DLSW use which tcp port to transmit and receive data.

i wang to know at which tcp or udp port does DLSW OR dlsw+ use to transport data?
thank you.

It really depends on the vendor. RFC1795 defines TCP 2065 and 2067 for DLSw. However, Cisco routers only uses TCP 2065 in DLSw version 1 mode. Cisco routers support DLSw version 2 (RFC 2166) in 11.3T. If two Cisco routers with 12.0 software, Cisco routers use UDP 2067 on top of TCP port 2065.

Similar Messages

How can I transmit and receive messages using Vector CANTech CancardXL with LabVIEW?

I'm a new LabVIEW user and I need transmit and receive CAN messages using a CancardXL from Vector CANTech with LabVIEW.
Could somebody have any vi or suggestion?

I made a set a LabVIEW VIs to work with Vector/Softing CANCards starting from an example program I downloaded from Softing. These use the Call Library Node to interface with the cards .dll.
I can't give these out because they were developed for a customer. I would contact Vector and see if they have an example program for your card. Might be the same one I started with.
[caution, salesman hat going]
Of course if you need help developing the VIs, we'd more than happy to assist you.
[remove saleman hat]
Ed Dickens - Certified LabVIEW Architect - DISTek Integration, Inc. - NI Certified Alliance Partner
Using the Abort button to stop your VI is like using a tree to stop your car. It works, but there may be consequences.

Monitoring Transmit and Receive Error

We have an monitoring system to monitor all the access points transmit and receive errors.
There are four column name "Receive Error", "Receive Discard", "Transmit Error" and "Transmit Discards".
I have notice that there are a lot of transmit discards packets than the rest of the columns for one of the AP.
Is it normal for the packets of the AP to have transmit discards high?

I notice that this AP the Dot11 driver runtime (1331728) is very high than normal Access point (78157)
The rest of the process runtime looks equal.
Is this indicate that the Dot11 driver is going to be faulty?
Transmit Discards AP
CPU utilization for five seconds: 0%/0%; one minute: 0%; five minutes: 0%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
22 127 10867611 0 0.00% 0.00% 0.00% 0 Per-Second Jobs
23 218 2173540 0 0.00% 0.00% 0.00% 0 Compute load avg
24 1134632 181178 6262 0.00% 0.00% 0.00% 0 Per-minute Jobs
25 1331728 317947128 4 0.08% 0.02% 0.00% 0 Dot11 driver
Normal AP
CPU utilization for five seconds: 0%/0%; one minute: 0%; five minutes: 0%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
21 238 10867159 0 0.00% 0.00% 0.00% 0 TTY Background
22 101 10867206 0 0.00% 0.00% 0.00% 0 Per-Second Jobs
23 170 2173453 0 0.00% 0.00% 0.00% 0 Compute load avg
24 1125336 181172 6211 0.00% 0.00% 0.00% 0 Per-minute Jobs
25 78157 318443069 0 0.00% 0.00% 0.00% 0 Dot11 driver

I used to be able to send and receive iMessages, now I can only send not receive. It's an iPad mini

I Used to be able to send and receive iMessages from my iPad mini, now I can only send iMessages and not receive them. It's the same withFaceTime, can FaceTime from the device but can't receive them.

Unable to make or receive FaceTime calls after April 16, 2014
http://support.apple.com/kb/TS5419
Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
http://tinyurl.com/a7odey8
Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/TS4268
iOS: FaceTime is 'Unable to verify email because it is in use'
http://support.apple.com/kb/TS3510
Using FaceTime and iMessage behind a firewall
http://support.apple.com/kb/HT4245
iOS: About Messages
http://support.apple.com/kb/HT3529
Set up iMessage
http://www.apple.com/ca/ios/messages/
iOS and OS X: Link your phone number and Apple ID for use with FaceTime and iMessage
http://support.apple.com/kb/HT5538
How to Set Up & Use iMessage on iPhone, iPad, & iPod touch with iOS
http://osxdaily.com/2011/10/18/set-up-imessage-on-iphone-ipad-ipod-touch-with-io s-5/
Set Up Alert Sounds
http://www.quepublishing.com/articles/article.aspx?p=1873027&seqNum=3
Extra FaceTime IDs
http://tinyurl.com/k683gr4
Troubleshooting Messages
http://support.apple.com/kb/TS2755
Troubleshooting iMessage Issues: Some Useful Tips You Should Try
http://www.igeeksblog.com/troubleshooting-imessage-issues/
Setting Up Multiple iOS Devices for iMessage and Facetime
http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
FaceTime and iMessage not accepting Apple ID password
http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
Fix Can’t Sign Into FaceTime or iMessage iOS 7
http://ipadtutr.com/fix-login-facetime-imessage-ios-7/
FaceTime, Game Center, Messages: Troubleshooting sign in issues
http://support.apple.com/kb/TS3970
Unable to use FaceTime and iMessage with my apple ID
https://discussions.apple.com/thread/4649373?tstart=90
iOS 7 allows you to block phone numbers or e-mail addresses from contacting you via the Phone, FaceTime, or Messages
http://howto.cnet.com/8301-11310_39-57602643-285/you-can-block-people-from-conta cting-you-on-ios-7/
How to Block Someone on FaceTime
http://www.ehow.com/how_10033185_block-someone-facetime.html
My Facetime Doesn't Ring
https://discussions.apple.com/message/19087457#19087457
How to watch FaceTime calls on the big screen with Apple TV
http://www.imore.com/daily-tip-ios-5-airplay-mirroring-facetime
Send an iMessage as a Text Message Instead with a Quick Tap & Hold
http://osxdaily.com/2012/11/18/send-imessage-as-text-message/
To send messages to non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
How to Text on the iPad
http://ipad.about.com/od/ipad_tricks/a/How-To-Text-On-The-Ipad.htm
How to Send SMS from iPad
http://www.iskysoft.com/apple-ipad/send-sms-from-ipad.html
How to Receive SMS Messages on an iPad
http://yourbusiness.azcentral.com/receive-sms-messages-ipad-16776.html
Apps for Texting http://appadvice.com/appguides/show/apps-for-texting
You can check the status of the FaceTime/iMessage servers at this link.
http://www.apple.com/support/systemstatus/
 Cheers, Tom

How would I import multiple Roadrunner emails each with multiple folders and continue to use my Roadrunner email to send and receive?

How would I import multiple Roadrunner emails each with multiple folders into Apple Mail and continue to use my Roadrunner email to send and receive from within Mail?

Try this.. Click the first in the CC field hold Shift, Click the Second Third, Fouth, Fifth and so on... click right Mouse select add to Contacts.

TCODES FOR SENDINGIG AND RECEIVING DATA THROUGH ALE

Hi,
All,
Message type I can find for the following :
Equipment master: EQUIPMENT_CREATE
Work centre: WORKC2, WORKC3 or WORKC4
Functional location: FUNC_LOC_CREATE
but i did'nt find a transaction code for sending and receiving data through ALE.
For example: Send material T.code BD10,
Receive material T.code BD11.
Please give the solution.
Regards.

can Tx BD21 is of any help

How to stop apps from sending and receiving data?

Or does it even matter because I have cellular data turned off...

If you have cellular data turned off apps can still send and receive data via WiFi. But why do you have apps that send and receive data if you don't want them to send and receive data?

Using a serial port via kermit and a USB adapter

I have need to use a USB->Serial adapter for connecting to console ports (Firewalls, etc). I bought a nice Keyspan adapter for this.
First, I've not been able to find a version of kermit that will work on Snow Leopard. Anyone have an updated version?
Second, which device do we use for "set port /dev/ttyXXX" ? Is there some novel way that the system tells you which tty is mapped to which port?
I'm sure there must be more to it... there is a disc with these USB devices for OS X (though I'm not sure they'll work in Snow Leopard).
Thanks!

Take a look at GoSerial http://www.furrysoft.de/?page=goserial it configures the port and acts as a terminal. There is also the screen command in the terminal, and minicom you can get though macports.

I want to transmit and receive the transmitted audio signal using labview with usrp ...can i get some help to do soo...thanks in advance

plz help me

this example receives frames on the same port. By CAN design you cannot receive the frame you are transmitting. If you want to receive what you transmit in addition there are 2 options:
- use the second port of your CAN device for Receiving the frames you transmit
- use the Self Receiption mode (refer to the manual for further details ho w to use this mode)

Using separate ethernet ports for LAN and internet

Following scenario:
A couple of Lion clients and a Lion server connected to a switch. Switch connected to router for internet access. All devices, clients, server and router are in the same C-Class net.
I'd like to connect the Lion server with 2 ethernet ports to the switch, so that one port is solely used for connections to the Lion clients (aka LAN) and the other port is solely used for connections to the internet. That way heavy LAN traffic to/from the server cannot bog down internet access to the server. Any ideas how to acomplish that?
Usually you would configure the Lion server as a router and connect the Lion clients (via a switch) to one port and the cable modem to the other, so both ports are in different subnets. But I don't want all internet traffic from the clients going through the Lion server.
The best I've come up so far was to configure both ethernet ports with static IP addresses. The one connecting to the clients with a 255.255.255.0 netmask but no router IP given. The one for internet with a 255.255.255.255 netmask and the router IP set to my physical router IP. It seems to work, but I'm not sure, whether this is the suggested way to do such a setup.
Maybe some manual editing of the routing table is are more solid solution?
Any tips appreciated.
Pete

What you want to do can be done but maybe not the way you are trying.
First yes, you would use two Etherner ports on the Mac, if it is a Mac Pro or XServe it has two built-in, other Mac models can do this using a USB Ethernet interface.
Next, the way I would normally do this is to have a separate switch for the WAN router, this would make the setup look like the following
LAN Switch ----- Server ------------ Router --- Internet
       | |                             |
       | |                            NAT
       | +-----------------------------+
       |
       +------ Client Devices
The router could be doing NAT via one interface, or a separate Firewall box could do the NAT.
Another possible way would involve segmenting the lan switch by setting up a VLAN and putting one port for the Servers second Ethernet connection on to that VLAN (using public IP addresses and the a connection to the router on that VLAN, the LAN switch could then route between the two VLANs. Cheaper LAN switches do not have this ability.

Different Ports for Sender and Receiver?

For testing a tool it would be nice to run RTPSender and Receiver on the same computer. But here?s the problem. I run VideoTransmit and AVReceive2 (both from the Sun code samples) with the following parameters. VideoTransmit should send to IP A and to Port 22224. AVReceive2 should listen to packets from IP B and Port 22224. Now VideoTransmit sends from a random port, but Port 22225 is used on both computers for exchanging user information. Because of this it isn?t possible to run both on the same computer because both want to use port 22225 for a connection.
Is there a possibility to change this?

http://java.sun.com/products/java-media/jmf/2.1.1/apidocs/
RTPManager
http://java.sun.com/products/java-media/jmf/2.1.1/apidocs/javax/media/rtp/RTPManager.html
SessionManager-Depricated
http://java.sun.com/products/java-media/jmf/2.1.1/apidocs/javax/media/rtp/SessionManager.html
You can Send and Receive on one computer.
Can't remember the combo though.
It's one of
transmit 192.168.1.255 22222 //multicastIP port#
receive 127.0.0.1 22222 //localhost port#
or
transmit 192.168.1.100 22222 //computerIP port#
receive 127.0.0.1 22222 //localhost port#
There is the answer in these forums somewhere.
I just hate to see people struggle.

Not able to Transmit and receive RTP in Linux

Friends,
I am not able to receive the RTP stream transmitted from another Linux machine though I was trying doing it with JMStudio. The transmit shows as if it is working properly and JMStudio in the receiver machine keeps waiting. Tranmission and receiving between the two same machines when in windows is fine.
Can anyone tell me what the problem is, do I have to add any feature to make this work in Linux.
Sreekant

I too am unable to transmit OR recieve RTP from Linux (RedHat 8.0). I am using JMF-2.1.1e and J2SDK 1.4.2.
I can play files on Linux and I can transmit and recieve between Win boxes (98 and 2K) but my RedHat (8.0 and/or 7.3) can not send or recieve to anyone or anything. I have tried JMStudio and RTPPlayerApplet.
TCPDUMP says udp port 22224 unreachable [tos 0xc0]
JMStudio says that no data has arrived.
I have all firewalling turned off and have tested on two different networks without success. All other networking functions are operational.
My problem is identicle to the problem decribed in the following linked post.
http://forum.java.sun.com/thread.jsp?thread=154947&forum=28&message=966551
I also found another discussion that referenced big/little endian problems in the JMF implementation. (scary stuff)
http://www.vovida.org/pipermail/rtp/2001-April/000112.html
Any help or tips on resolving this issue are welcome. I will be happy to supply more info if needed. Also, if anyone has managed to get RTP working on Linux then what versions Linux/JDK/JMF, what program?
Thanks in advance.

COPA: how to identify which cost element for sender and receiver in IMG

Hi Guru,
I know my cost element for sender and receiver from the settlement document, but where in IMG, i can identify how it settup to use which cost element for my sender - order , which cost element should be used for my reciever profit segment.
Thanks,
Kick

Hi,
Go to KEI1
Select your transfer structure
double click on assignment lines
check the source and value fields to get the mapping.
Regards,
Sridevi
<i><b>Pls. assign points, if useful</b></i>

What address i should i give to transmit and receive web cam image

hi
I want to Know what address and port i have to give send and receive the web cam

The IP address should be the IP address of the computer that should receive your transmission. If you want all the computers on your subnet to receive the transmission, then use 255 as the last number in your IP address. For example, "192.168.1.40" can be used for a point to point transmission and "192.168.1.255" can be used for all computers that are on your subnet. .
The base Port number can be any port number that is not in use by any other service on your computer. For example, you can use "22222". Make sure that it is an even number. The first media track will be transmitted from the base port number. The next track will go to base port number plus 2 and so on.
Regards
Praveen.

Callback for transmit and receive

NCTYPE_STATE _NCFUNC_ MyCallback (
                                    NCTYPE_OBJH       ObjHandle,
                                    NCTYPE_STATE      State,
                                    NCTYPE_STATUS     status,
                                    NCTYPE_ANY_P      RefData)
     if ( (State & NC_ST_WRITE_MULT ) || (status == CanErrFunctionTimeout) )
          status = ncWrite(ObjHandle, sizeof(Transmit), &Transmit);
     else if (State & NC_ST_READ_MULT)
     status = ncReadMult(ObjHandle, sizeof(ReceiveBuf), (void *)ReceiveBuf, &ActualDataSize);
     ..... some other codes....
my calls to callback:
Transmit :      Status = ncCreateNotification (TxRx, NC_ST_WRITE_MULT, 100, NULL, MyCallback);
Receive:        Status = ncCreateNotification (TxRx, NC_ST_READ_MULT, NC_DURATION_INFINITE, NULL, MyCallback);
I provide two buttons to call either transmit or receive and when I run my program and call either one of these functions ONCE, the ncCreateNotification run continuously till my whole debugger hangs. I am using borland Cand USB-CAN. Can someone help me on this?

Seems like I cannot create two objects at the same time. I am trying to create objects: TxObj and RxObj.
Both values are the same. 0xA601A0.
The flow of my program goes like this:
- configure object through ncConfig and ncOpenObject
- transmit by calling ncCreateNotification and I will call this from time to time if I wish to transmit any data. This function returns a 0.
- receive by calling ncCreateNotification and this will return NC_ST_READ_AVAIL. I will only call this function once and it will return me data if there's any message sent.

DLSW use which tcp port to transmit and receive data.

Similar Messages

Maybe you are looking for