DMC250 unable to see my PC

I have a DMC 250 Director. On my pc I have installed the Cisco Media Server and Cisco Media Player. I also have a Cisco Media Hub.
Problem: The DMC250 can not see my pc as a Music Source unless I disable the firewall on my pc. The Media Hub shows up.
I have followed the instructions in the Troubleshooting part of the Users Manual and inserted an exception: Name UpNP, Port 8015, protocol TCP in the firewall. I have also enabled the Cisco Media Server in the Programs Exception list.
However, when the firewall is active the pc does not appear. Stopping the firewall makes the pc reappear in the source list.
Note: From the Media Player I can see my pc as a source along with the Media Hub, and I can play the music from my pc on the DMC250 using the Media Player to place a tune in the playlist.
Any suggestions to what additional settings I have to make in the Firewall?

What is the firewall that you are using? You can also try these articles.
Installing Wireless Home Audio with McAfee
Installing Wireless Home Audio with Trend Micro Internet Security Pro
Installing Wireless Home Audio with AVG
Installing Wireless Home Audio with Zone Alarm
In general, you only need to have 3 applications to be allowed on the firewall.
WHASetup.exe
AVMediaServer.exe
CiscoMediaPlayer.exe
FAQ on firewall configuration for Wireless Home Audio Setup

Similar Messages

Unable to see interface on ASA 5510 Firewall

Hi All,
I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0/0                x.x.x.x           YES CONFIG up                    up
Ethernet0/1                x.x.x.x           YES CONFIG up                    up
Ethernet0/2                unassigned      YES unset administratively down down
Internal-Control0/0        127.0.1.1       YES unset up                    up
Internal-Data0/0           unassigned      YES unset up                    up
Management0/0              192.168.1.1     YES CONFIG up                    up
Please suggest what could be the reason.
Regards
Pankaj

Hi Ramraj,
Even i have the base license for my ASA 5510 which is showing all the 4 interfaces in sh ver. I don't think so license would be an issue. There should be some IOS code bug that needs to be upgraded. If this goes for an OS upgrade it should get resolved.
Its not showing up in sh ver . As Karsten said he might be running on old IOS version.
fy-a# sh ver
Cisco Adaptive Security Appliance Software Version 8.4(4)1
Device Manager Version 6.4(5)
Compiled on Thu 14-Jun-12 11:20 by builders
System image file is "disk0:/asa844-1-k8.bin"
Config file at boot was "startup-config"
fy-a up 1 day 1 hour
Hardware:   ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW016 @ 0xfff00000, 2048KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                             Boot microcode   : CN1000-MC-BOOT-2.00
                             SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
                             IPSec microcode : CNlite-MC-IPSECm-MAIN-2.06
                             Number of accelerators: 1
0: Ext: Ethernet0/0         : address is 2c54.2d0c.8f1a, irq 9
1: Ext: Ethernet0/1         : address is 2c54.2d0c.8f1b, irq 9
2: Ext: Ethernet0/2         : address is 2c54.2d0c.8f1c, irq 9
3: Ext: Ethernet0/3         : address is 2c54.2d0c.8f1d, irq 9
4: Ext: Management0/0       : address is 2c54.2d0c.8f1e, irq 11
5: Int: Not used            : irq 11
6: Int: Not used            : irq 5
Licensed features for this platform:
Maximum Physical Interfaces       : Unlimited      perpetual
Maximum VLANs                     : 50             perpetual
Inside Hosts                      : Unlimited      perpetual
Failover                          : Disabled       perpetual
VPN-DES                           : Enabled        perpetual
VPN-3DES-AES                      : Enabled        perpetual
Security Contexts                 : 0              perpetual
GTP/GPRS                          : Disabled       perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 250            perpetual
Total VPN Peers                   : 250            perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
This platform has a Base license.
Serial Number: JMX1AXXXXX
Running Permanent Activation Key: XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Configuration register is 0x1
Configuration has not been modified since last system restart.
fy-a#
Ramraj please do correct me if am wrong.
Please do rate if the given information helps.
By
Karthik

When using the camera downloader in Adobe Bridge CS6 with Nikon D5200 we are unable to see previews of the photos and it is very slow to download. The issue occurs under a the users rights, but not under admin level. This is a new issue

When using the camera downloader in Adobe Bridge CS6 with Nikon D5200 we are unable to see previews of the photos and it is very slow to download. The issue occurs under a the users rights, but not under admin level. This is a new issue.

Hi Jdentremont,
Lync client gets user photos by first querying the Address Book Web Query (ABWQ) service on the server, which is exposed through the Distribution List Expansion web service. The client receives
the image file and then copies it to the user's cache to avoid downloading the image each time it needs to be displayed. The attribute values returned from the query are also stored in the cached Address Book Service entry for the user. The Address Book Service
deletes all cached images every 24 hours, which means that it can take up to 24 hours for new user images to be updated in the cache on the server.
To troubleshoot your problem, please follow the steps below:
1. Navigate to
“X:\share\1-WebServices-1\ABfiles\000000000\000000000” folder. (ABS file share)
You should see some photo files in this folder as the following screenshot.
2. Delete all the files in this folder.
3. On test PC, delete local cache files.
%userprofile%\AppData\Local\Microsoft\Office\15.0\Lync\[email protected]
4. Sign-in Lync with the test account.
5. Go back to the ABS file share, check if there is any Photo file in the folder.
Best regards,
Eric
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Unable to see pipe line steps in the SXMB_MONI

HI,
i have done the development and quality work for my p i7.1
i was testing the messages in the Quality System.
So i went to SXMB_MONI to see the messages.
After double clicking on the successfully processed message, it shows
pipe line steps.
in that I am able to see
1.inbound message(CENTRAL)
2.XML Validation inbound channel Request
3. call adapter
4. Response
but i am unable to see
1. Receiver Determination
2. Interface Determination
3. Receiver Grouping
4. Request Message Mapping
5. Technical Routing
whereas in the develoment system i am able to see the above all.
is there any configuration i have to do in the SXMB_ADM?

can i know that Configuration objects were created/ imported by using transport mechanisum?
if created ,
check the cache status and re activated those objects whatever u r posted in thread.
if transported :
u ll follow ,whatever posted by Earlier

Unable to see 'Search Dialog Box Component' option

In trying to follow Thilo Brandt's article to 'Develop a Serach Component for KM Search iView', but I'm unable to see Content Management -> User Interface -> Mapping -> Search Dialog Box Component. Is there something I need to 'turn on' so that I can view that option?
We are using EP6 SP2.
thanks,
Biju.

Forgot to mention that the article is available at: https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sapportals.km.docs/documents/a1-8-4/developing a search component for km search iview.article

HT204291 Airplay mirroring. Macbook 2012 retina display. Unable to see desktop on television, audio works perfectly. Both OS on ATV and Mac are running latest versions

Airplay mirroring.
Macbook 2012 retina display. Unable to see desktop on television, audio works perfectly. Both OS on ATV and Mac are running latest versions.
Firewall set correctly (allow incoming...)
When I click mirroring to turn it on, teh Apple TV screen goes blank (from its home setting)
Any help appreciated.

Hi!
I figured it out! It was a firewall issue.
I use Handsoff and I checked it before i wrote here. There was no "user defined rule" that denied the communication but when i changed to "All rules" the program displayed several rules regarding AppleTV and its IP.
So if anybody has the same problem make sure you see all rules of your firewall and get rid of the AppleTV related rules generated by the program itself. You dont need to update to the latest iOS on the AppleTV!
I hope that I can help some people with this info to fix the problem.

Wired computers unable to see printer on Airport Express...help?

Hi all,
I recently set up an Airport Extreme on our office network to offer wireless network access piggybacked on our wired router. I then purchased an Airport Express which I was planning on using as a wireless print server for our Canon i9900 for all office computers connecting wired or wirelessly, which would interface with the network via the Airport Extreme Base Station.
I have configured the Express as an extension of the existing Airport network, and attached the printer to it via USB. All the computers in the office which have airport cards onboard can see and print from the printer, which is great. The problem is that all of the computers connecting to the network via wires are unable to see the printer (this is under both 10.3.x and 10.4.x, all airport software completely updated.) The Extreme base station shows up for all office computers in their Airport Admin Utility, AND if the printer is connected directly to the Extreme Base Station via USB, all computers can see the printer over Bonjour/Rendevous.
Anybody have ideas as to how I can get my wired machines to see the printer on the Airport Express?
Thanks!!

Applications > Utilities > Airport Admin Utility
Scan and Select your Airport
Click Configure
On the Airport Tab
Base Station Options...
Check Enable Remote Printer Access
iFelix

Unable to see the personalization link on any page

Hi,
I am unable to see the personalization link on any of my pages (not even on login page).
I am setting the profile option value to "Yes" for the profile option
FND: Personalization Region Link Enabled
Also I have bounced the Apache.
Please help me as I am stuck due to this.
Thanks,
Anoop

Did you enabled the profile option Personalize Self-Service Defn (FND_CUSTOM_OA_DEFINTION) .It must be set to Yes.
Abhay

Unable to see data in Table in smartform

Hi all,
I need to create a smartform where I have to print the header details at the start and then below that details for all line items for a particular document.
so i have data ;ike :
Header data :
field 1 : field 2:
Field3 : field4:
field5: field6:
Item data :
field1 field2 field3 field4 --> Item 1
field1 field2 field3 field4 -->Item 2
field 1 field2 field3 field4 -->Item3
For the Header data,Im planning to use a template in a secondary window.
However for the item data,i need to use a table (As i know the no of records only at runtime).Also another reason for usng table would be that I dont need the header on each flloowing page but only the Line item details on the following pages.
Now my ques is :
1.I hav ecreated the form and put some constant /texts to just test the form.I am able to see the texts/data in the header data.However Im unable to see the data for the Item i.e. in the TABLE.
I have used template for Header details which I can see.
I dont know what Im doing wrong.Is it because in the DATA tab under TABLES,I have given an interna table but there is no data in the table?
I have defined only 1 line type in my table an dthat has 4 cells (as I need to print 4 item fields under the Item data)
PLease let me know what I am doig wrong because of which Im unable to see the item data in table form.
Thanks!

Hi,
Have you used any exists?
in exists is there any system date kind?
Can you try to run your report thru RSRT and use debug option there.
before reporting please check your all connected targets have data for reporting.
mean at targets-->request tab, reporting symbol was there or not.
Any master data objects included in multi provider?
if yes then please check those, if any ACR was running then it may cause you.
if possible try to develop simple query with as per needs(mean to see 2015 data only).
As my guess selections/filters migth be hidden, please check those.
Thanks

Unable to see master data changes

I added a new field as an Attribute to Master Data (Customer Number) and loaded the data which was successfull. I created an infoset and created a report but am unable to see the values in this new field. I check 'Values in the Infoprovider' on the reports. Also when i go to RSISET and look for Infoset Values I do not see them there.

Hi,
I think there are two things you should check:
1. Have you seen the data for which you added into the attribute in your InfoObject?
2. Have you seen the field which you added into the attribute in your InfoSet?
If you got a "NO" answer, you maybe lose step(s).
Hope above helps you.

Unable to see line items in segment clearing account

Friends,
Why we are unable to see the line items in intersegment clearing account/zero balance clearing account, eventhough the master is maintained as open item and line item display.

Hi,
I have received the following error message.
Account 1999990, company code xxxx is clearing account
Message no. MSITEM111
Diagnosis
You have stored account 1999990 in company code xxxx as a clearing account. At the same time, you use line item management with this account.
System Response
Error message issued because line item display cannot read data for an account in a ledger if line items exist partially in the entry view together with clearing items for which there are no line items. In such cases, only the data with line items would be selected.
Procedure
Check the Customizing settings or account control. Change the settings so that only automatic postings without line items can be made to the account, or select a different account as the clearing account.

Unable to see the values in detail block

Hello,
I have a master detail block, when I query the form, I am unable to see the values for a particular field(Column), all other columns appear properly in the details block, Upon checking the same table(s) in SQL ( by using the JOIN defined in the where clause of the relationship in Forms) , it shows the relevant records for all fields. So what could be wrong with the Form, please advise.
Thanks
FM

IQ wrote:
I have just checked the field its a non-database field which is being used as a LOV column to display a value derived from LOV. How do I make this populate at Query time, as obviously this works when the Form is in a insert mode but not for Query mode. How to make it work for Query ? As it for LOV column and non-database filed, ignore my first suggestion.
Does your non-database filed has associate any column ?
For example, you have SUPPLIER_ID (database column) and SUPPLIER_NAME (non-database column). SUPPLIER_NAME has LOV column. And when selecting supplier name from LOV value also assign at supplier_id.
Now to show supplier name when querying, you have to write POST-CHANGE trigger at supplier_id. like
SELECT ASSC_CODE INTO :MST_SUPPLIER.ACC_CODE
FROM ACC_SUB_SUB_CONTROL
WHERE ASSC_ID=:MST_SUPPLIER.SUPP_ASSC_ID;Hope this helps

Unable to see other writer's checked check boxes in comments of shared review

I'm using Acrobat 3D Version 8 in a Windows XP environment. We are using SharePoint for shared reviews.
We are able to see developer's comments, and we can respond back to the comments with a reply. However, when we use the checkbox to indicate that a comment has been addressed, each writer can only see the checkmarks that she makes. We cannot see checkmarks made by other writers.
We have tried selecting the check box, and we have also used the check box icon to select the check box. We then publish and the the action is accepted as a comment and is published. But we are unable to see each other's check boxes.
Why?
Thanks!

Solved on my own.
Simply close BEx Analyzer and restart it again. If still it doesn't work then restart your computer and then run BEx Analyzer again, it will definitely work.
TR.

Unable to see live data view for a access db

I'm using the following:
Asp.net C#
Server 2003 Sp2/
DW CS3
Access db
I'm attempting to connect to a "local" db on my server.
I use the database connection string"
Provider=Microsoft.Jet.OLEDB.4.0;
Data Source=C:\catalog\Catalog\files.mdb;
Persist Security Info=False
ole db connection
While in the data link properties window the connection is
successful but in the ole db connection window I get "An
unidentified error has occurred".
If I just press ok I'm unable to see any of the table in my
db.
All I want to do is setup the Live Data view
Thanks in advance for all your help.

"madhooper" <[email protected]> wrote in
message
news:fcc6vt$jd6$[email protected]..
>
>
> I'm using the following:
>
> Asp.net C#
> Server 2003 Sp2/
> DW CS3
> Access db
>
> I'm attempting to connect to a "local" db on my server.
> I use the database connection string"
>
> Provider=Microsoft.Jet.OLEDB.4.0;
> Data Source=C:\catalog\Catalog\files.mdb;
> Persist Security Info=False
> ole db connection
>
> While in the data link properties window the connection
is successful but
> in
> the ole db connection window I get "An unidentified
error has occurred".
>
> If I just press ok I'm unable to see any of the table in
my db.
>
> All I want to do is setup the Live Data view
>
> Thanks in advance for all your help.
Did you configure your testing server?
Set up a testing server
http://livedocs.adobe.com/en_US/Dreamweaver/9.0/WSc78c5058ca073340dcda9110b1f693f21-79e0.h tml
Preparing to build dynamic sites
http://livedocs.adobe.com/en_US/Dreamweaver/9.0/WSc78c5058ca073340dcda9110b1f693f21-7a31.h tml

Unable to see "New from Par" option while creating Custom portal layout

Hi All,
I am unable to see "New from Par" option in Content Administrator. I am trying to create a custom page Layout for which I am need create layout using new par file. I am not able to see this menu option. Does anyone know from where to enable this option?
Nitesh

There is no option like "new from par" from ep 7.
Create an iview based upon portal components.
check the below link for creation
http://help.sap.com/saphelp_nw04/helpdata/en/f5/eb50360e6a11d7b84900047582c9f7/frameset.htm
Koti Reddy

DMC250 unable to see my PC

Similar Messages

Maybe you are looking for