DMR for skipping inspection lots

Hi friends,
I am new to QM. I want to create DMR for skipping four lots after one inspected lot.
Can you please tell me, configuration steps reqd.
Thanks in advance.

Tcode QDR1 > set name > at lot creation > next >
stage 10 > click on insp stage, Severity 04
stage 20 > tick on skip
stahe 30 > Severity 04
select both lines & click on stage change
stage 10
no. of insp : 1
new insp stage : 20
rej : 1
new insp stage : 10
stage 20
no. of skip : 4
new insp stage : 30
rej : 1
new insp stage : 10
stage 30
no. of insp : 1
new insp stage : 20
rej : 1
new insp stage : 10
& save
now u can apply this DMR in inspction plan
It may help you.

Similar Messages

Skip Inspection LOT

Dear Gurus,
suppose one material having QM activate,all the processes have been carried out on regularbasis.
now if a vendor supplies material with no rejection last three months,system should skip inspection lot
material should post the stock to unrestricted not in QC. stock
is it possible in SAP
Siva

Keep in mind that dynamic modification is not time driven. It is lot driven. You cannot specify any set times.
The only time you can specidy a number of days is for the reset value. The DMR gets reset if NO lots are created in a given time. Each time you get a new lot, the reset date is recalculated.
FF

How partial inspection is done for a inspection lot & vendor payment done based on inspection result

Dear Gurus,
In our business 1000 bag material is received in one material document. So one Inspection lot is created.
Now business take randomly 10 bags from that 1000 bag & inspected. The Bags are inspected on various parameters such as Weight , Fabric , Valve Size , Cross Sec Area, Print Quality , Stitching Thread , etc . The values for all this types of parameters are prepared in an excel sheet in a prescribed format.
The Values for each Quality Parameters are then matched with the desired prescribed average figures.
Based on the Values which deviate from "Average" figures , deductions are computed
Logic is 1% for single defect in a bag for 1 parameter . Likewise if more defects is found then add 1% in multiples
e.g 1% + 5 defects then .05 * basic Raw material cost .
This figure along with proper description is recorded under "Remarks" column of the report format and send to Accounts department for the
deduction process from Vendor
we need to capture the inspection parameters in system as per the above process.
And please tell me how I configure this process in SAP .
Thanks & Regards,
Bubai

Hi Bubai,
you can create a QM Control Key (which is used to QM View of Material Master) which you have to set the indicator Block Invoice. This indicator is blocked invoice with blocking reason I (I = Inspection) if there is still no usage decision for the inspection lot or the inspection lot is reject.
(SPRO -> Quality Management -> QM in Logistics -> QM in Procurement -> Define Control Keys).
Best Regards,
Apostolos

Standard Report for all inspection lots

Dear all,
Pls guide me from where I can retrieve the data for result recorded for MIC, inspection lot wise.
Actually currently working for Pharma company where we are using, Inspection Plan (task list type Q), with inspection point 200 u2013 Physical sample. Materials are being managed through Batches, so each inspection lot is having separate batch number.
Now the requirement is to find a STD sap report that can retrieve us the result for a material for all the inspection lots (Batches) it have, in the report type from where I can down load it to word/excel.
In short, the report should contain, Material, results for all MICs under all inspection lots.
I have already tried out;
QGP1 but it shoe the result for only a MIC at a time.
QGA2 but not able to visualize results for all MICs at once.
MCXB but, gives only the quantity of MICs not the results of it.
Regards,
Shyamal Joshi

Hi Craig,
The requriement is to have results for the Inspection lots only, not for the batch values.
The report MCXD is giving the quantitative analysis for the batches, I will be very pleased if you suggest me any report that gives me the results (values entered during result recording) of these MICs, inspection lot wise, just as the MCXD give quantitative.
I think the term BATCH is creating confusion, that is Y u have suggested me CL03N, but as I have mentioned eariler also, currenlt working with Pharma company, where each manufacturing lot is give a batch number, (in sap terminology the Batch management function, MSC1N), that is why i freauently used BATCH. Sorry for that communicational error from my side, and I am very much thank full to you for your each valuable comment, suggestion.
Regards,
Shyamal Joshi

Error in Setup Tables for QM Inspection Lots

Hi,
I have an issue when I attempt to fill the setup tables for QM that I receive the following error for the Inspection Lots (QV) only. When I fill the setup tables for Notifications and Inspection Results, then these are OK and use the same standard function module 'qmex_inspection_lot_import_ini'.
"Internal error in program SAPLQMEX, function module / subroutine qmex_inspection_lot_import_ini, code 1".
Has anyone any ideas of the cause or have you experienced this before?
Thanks,
Scott

Hi,
The most likely reason that leads to the above error message in your
system is an inconsistency of the inspection lots.
To get the inconsistent inspection lot,please check your system in the
following way:
- transaction OLIQBW for running Setup table
- switch on debugging mode
- set break point in the function QMEX_INSPECTION_LOT_IMPORT_INI
on the line:
ELSE.
   MESSAGE e011(qmex) WITH sy-repid
                           'qmex_inspection_lot_import_ini'
                           '1'.
> then excecute F8 to go to this break point.
- double klick on ' l_qals-prueflos'
on line 77 in the same function QMEX_INSPECTION_LOT_IMPORT_INI:
READ TABLE qave_tab INTO l_qave
                    WITH KEY prueflos = l_qals-prueflos <      here !
                    BINARY SEARCH.
Please check following note:
305244 Missing operations for the inspection lot
89541 Inspection lot exists w/o status object: EM BS001
536769 Inspection lots without status object
Thanks,
Venkat

Multiple notifications for an Inspection lot

Hello
I would like to create one notification by defect keyed for an inspection lot .
If I work with serial numbers I can create one notification by defect
If I don't use serial numbers , all defects are linked to a single notification even though I remove the tick for "One notification by Inspection lot " in the Inspection lot category customizing ?
I would like to know if there is a way to do that.
Thanks for your help
Regards
Regis

It seems this link has got some useful replies:
Multiple notification creation for defects recorded during UD
Also other similar discussion:
Multiple notification against single inspection lot (03 inspection type)

Collective UD for 04 inspection lot origin

Hi All,
I need to know about collectived UD for 04 inspection lot origin. In QA16, I do not get any 04 lots. Do I have to go for QA41? Then what are the prerequisites and configurations?
Thanks in advance!

Hi Sujit,
I tried this and made a variant in QA41 too. But some its not working. I searched in google and SDN and found all steps are followed, but its just not working.
My settings are:
1. Auto UD time taken as 12 hours in customizing
2. Auto UD box ticked for material
3. In QA41, created a variant (In full screen)
4. Inspection lot selection taken as order confirmed
5. UD codes, plant all set
Now what i feel i am mistaking in scheduling the variant. Can anyone please let me know the steps to schedule it?
My scenario is: for 04 type materials, I want to do a collective UD when lots are OK
And Do I have to assign to any material?
Thanks!
Edited by: SAPQM11 on Sep 15, 2010 8:00 AM

Skip inspection lots

Hi All,
Can anybody please guide me abt Skip lots and automatic usage decion.
According to what I have understood,if i activate Skip lots and automatic UD tick in QM view of Materail Master and keep the characterstics in Inspection plan as optional charracteristics,Automatic UD will be made for the lot after particular time lapse (time maintained in Customising) and stock posting of lot will be done to unrestricted stock
My doubts are-
Is result recording required?
When will the lot have stats as SKIP?
Are there some more conditions for SKIP lots?
Please guide and also correct me if I am wrong

Hi
If I am not using dynamic modification rule,Can i not skip lots?
No
Also,If i can,is result recording necessary if DMR is not being used?
It is not mandetory to do RR for SKIP lots
My scenario is that my client does not want to deactivate the inspection type in setup but does not want inspection for a particular material to happen for next 4 months.
Best sloution will be to use Quality Info Record for the same.
As you aware that Quality Info Record is Vendor-Material-plant combination.
So in QI01-->You can Maitain Relese Date: -->This will be 4 months Hence date.
& In Inspection control of QInfo record you can maintain "No Inspection"
This will put material to Unrestricted use directly after GR made till valid date.
After that you can change the date.
or
Use DMR & in QDR3 you can maintain "Reset period " as 4 months.
this will reset the DMR & lots will come to Quality for inspection.
I hope this will add some value.
Regards
Sujit

How to do single usage decession for multiple inspection lots

we are clearing Usage decision each & every lot for which taking lot of time, if any setting for a GR Document number/Multi GR document nos connected lots to be cleared at a time automitically,

Hi,
In addition to Anupam's reply,
Follow the SPRO path for Auto UD---> Select your plant for AUTO UD settings -
> then go to InspLot completion tab where you need to define following time fields under Automatic Usage Decision tab page :
Delay time for skip lot (in Mins)
Waiting time (hrs) & Waiting time (Mins).
Waiting time is the time which must elapse after inspection lot creation after that only system will carry out automatic usage decision.
Save above settings.
Further as a master data part, you need to maintain tick in Automatic UD check box for the respective material for which you want activate automatic UD.
Hope this clears your doubt.
Revert if still any query.
Regards,
Tejas

QM 'Skip' Inspection Lot Characteristics

Does anyone know where I would be able to find information on 'Skip' master inspection characteristics through an inspection lot? And, is it possible for a certain characteristic to skip on a scheduled interval as opposed to a characteristic that is skipped every time?
Thank you

Try http://help.sap.com/saphelp_40b/helpdata/en/2d/350bd8448c11d189420000e829fbbd/frameset.htm
Regards
Bala

Resetting a sample for an inspection lot

How to reset a sample to an inspection lot, and transfer stock to inspection lot.

Try using the transaction codes QAC2 and QAC3 for both of your queries.
or open the inspection lot in change mode and assign the sample you would like.
Hope this helps you.

For the Inspection lot status is CRTD instead of REL status

Dear Experts,
Today I have observed strange behavoir of the system.
For the Finished material 04 insp type, Every day we used to generate inspection lots automatically with MB31for 101 mov type.
generated inspection lot status will be REL bydefault. Today we observed system status is CRTD.
I have checked any material master/Inspection plan been change or not, but it was not changed.
Please suggest how this behavior happen suddenly.
Regards
Don

Dear Don,
Check in SPRO for inspection type configuration. Some body has changed the 'Task list usage' for Inspection type.
If you are using '1' and if there is other one except '1' then system will create inspection lot in CRTD status.
You need to change it manually in QA02 and assigne plan.
Thanks and Regards
Harriesh.

Enhancement for QA01 (Inspection Lot)

For creation of new inspection lot via QA01; upon saving, user wants to disable printing of the inspection lot form (sapscript using standard print program 'RQEEAS20') when the system status 'QALS-KZSKIPLOT' = 'X'. May I know how should I go about to start? (if user exit? which user exit?)

Hello,
Here i suggest you that if you are using Exit for UD then in that only just apply one code where program first will check the QAMR/QASR etc. all result table field w.r.t inspection lot and if fields found empty means no data or RR then system wont pass UD code for UD posting.
Or just make first MIC as required MIC and apply the code in that first MIC, if that MIC value is blank then again system wont allo UD.
Secondly, Status profile maintenance is also an another stdn way to execute the requirement.
Regards

SAP QM Default Inspection Plan for all Inspection Lots created in the Plant

Scenario: We have a Proto type plant in which Daily 15 to 20 materials are created every day. We have only one inspection plan for all the materials.
Problem: We don't want to do material assignment in the Inspection Plant header every time a new material is created
Requirement: Is there any way to default the inspection plan for all the inspection lots created in the Plant by Standard Configuration or User Exit.
Your answers will be much appreciated and rewarded.
Thanks in advance,
Thiyagu

Hi,
In our case Creation of Inspection lots are controlled by QM View of Material Master. Our problem is to find alternative for assignment of New Materials in the Plan header in Tcode QP02, as we have only ONE INSPECTION PLAN. So our expection is all QM Inspection Lot created in the Plant should always get assigned to the SINGLE INSPECTION PLAN, with out doing any assignment of material in the Plan.
Thanks,
Thiyagu.

Batch not created for the Inspection lot?

Hi Experts,
I have created a the production order by inputting the Batch in the GR tab and released the production order. The release of Production order will create a Type 03 lot , but surprisingly it doesn't show the Batch in the Batch field when i look the inspection lot that was created by release of production order, instead it shows blank. I have checked the material master and it is batch managed material. Please let me know where I'm going wrong.
Configuration- Batch is unique at material level indicator checked
my plant has Batch status management indicator
Please find the screenshot below for type 03 lot and also the Batch management indicator in material master in sales/general view, work scheduling and warehouse1.
Thanks,
Pavan

Hi Pavan,
According to SAP Note 50618, you may consider to implement the correction on that note or use partial lot assignment.
For partial lot assignment, you can find the setting in Routing header and customizing in SPRO with path: Quality Management - Quality Planning - Inspection Planning - General - Define Identifier for Inspection Points.
There's also another discussion regarding this issue. Please find here.
Regards,
Julian

DMR for skipping inspection lots

Similar Messages

Maybe you are looking for