Do CSS 11500 series allow remote SPAN?

Hi,
I found SPAN (Switch port analyzer) is available on CSS 11500 series, but could only found destination must be local. Is it possible to do remote SPAN and make the destination be in another remote switch?
And how many local span sessions are allowed?
Thanks,
Rgds
Jorge

Cisco WebNS Software Version 7.20 delivers support for a new Cisco CSS 11501 model and Cisco WebNS Software 7.20 supports SPAN the features.
Switched Port Analyzer (SPAN) or port mirroring is useful for network analysis?a copy of the packets received or transmitted by a source port is sent to a designated destination port.
Kindly go through these links to get detailed information:
http://www.provantage.com/cisco-systems-css11503-ac~7CSCO288.htm
http://www.cisco.com/en/US/products/hw/contnetw/ps792/prod_release_note09186a008077c440

Similar Messages

CSS 11500 Series Query

Hi
I have 2 CSS 11500 series units working in a master / slave configuration.
Both units are identical in regards to hardware, IOS, etc.
1 unit allows the running config to be saved by the ' copy run start' command where the other goes through the motions of saving, but a 'show startup-config' shows nothing.
This unit seems to be operational in every other regard. Is this a hardware fault or am I missing a software command somewhere along the way ?
Thanks
Ian

You get such problems when the device is running short of memory. Try increasing the DRAM because what is happening is that the device saves the config in the NVRAM but it does not have enough DRAM to display the configuration when the "sh startup-config" command is executed. A temporary solution is to restart the device, if the problem persists then you have to upgrade the memory.

Services with different IP address subnets over CSS 11500 series

Hi all folks!
I have two CSS 11500 series...
In just a few months i will have ready a DRS (Disaster Recovery Site), where i will have 2 more servers to add to the environment.
But this servers will be in a different subnet from that today i have for the servers who are configured in the current services of my CSS.
So then the doubt i arises is:
Is correct to add two new services with these servers, but using the IP addressing of the DRS site???, and including on the CSS a static route to this network, (of the DRS) in order to reach them?? is it correct, it will work well?
This would be so....
             ________________LAN to LAN_____________________
             |                                                                                |
             |                                                                                |
|------SITE A------|                                                        |------SITE B------|
     [Firewall] ===============IPSEC============= [Firewall]
           |                                                                                |
           |                                                                                |
[CSS-A]-[CSS-B]                                                            [SWITCH]
       |          |                                                                     |         |
     [SWITCH]                                                                    |         |
[srvA] [srvB] [srvC]                                                          [srvD] [srvE]
So, at [CSS-A] & B, i will put a static route to firewall that know the subnet of site B through the IPSEC tunnel.
So In the CSSs, i will add the new services for the Servers "D" & "E" with the IP address of Site B.
This should be seen as well:
!*************************** GLOBAL ***************************
ip route 0.0.0.0 0.0.0.0 [IP FIREWALL]
ip route SITE B [IP FIREWALL]
!************************** SERVICE **************************
service srvA
ip address A.A.A.x
port 8080
service srvB
ip address A.A.A.x+1
port 8080
service srvC
ip address A.A.A.x+2
port 8080
service srvD
ip address B.B.B.y
port 8080
service srvE
ip address B.B.B.y+1
port 8080
I know that this practice is not the most desirable, in fact should use"Basic Global Server Load Balancing Site Redundancy Using the CSS with DNS", but I don't have much time to change the entire environment today, and in this first stage i have to begin with this poor but quick solution that i thought and i wanted to be validated if there is posibliidades this to work
Within their experiences that they say? Will operate?
Thanks in advance!
Regards!
Esteban =)

Daniel!
Sorry by delay!
Thank you so much for you time for reply.
You have given me a great help to this doubt!
But..using "source group" let me know..
I can´t undertand the really difference between NAT with ACls as you can see at this link: (http://www.cisco.com/en/US/products/hw/contnetw/ps789/products_tech_note09186a0080093dfc.shtml)
and
this other link, using NAT (from the piont 5), (http://www.cisco.com/en/US/products/hw/contnetw/ps789/products_configuration_example09186a0080093dff.shtml)
where the NAT is configured under a method different from the previous one..
So.. for this scenario described above, which would you recommend using? I would think that the second is the most indicated truth? What do you think?
Thanks in advance again!!!
Have nice day!
Regards.
Esteban.

CSS 11500 Series LOGs

Hi everyone,
I need some help about one type of CSS 11500 LOG messages:
OCT 12 07:47:03 1/1 273 WCC-6: Computing slow start parameters for newly activated service index 4
OCT 12 10:25:05 1/1 274 WCC-6: Computing slow start parameters for newly activated service index 3
OCT 12 11:19:49 1/1 275 WCC-6: Computing slow start parameters for newly activated service index 3
OCT 12 11:26:33 1/1 276 WCC-6: Computing slow start parameters for newly activated service index 3
OCT 12 12:20:37 1/1 277 WCC-6: Computing slow start parameters for newly activated service index 3
OCT 12 14:04:32 1/1 278 WCC-6: Computing slow start parameters for newly activated service index 4
OCT 12 14:04:53 1/1 279 WCC-6: Computing slow start parameters for newly activated service index 5
OCT 12 14:05:01 1/1 280 WCC-6: Computing slow start parameters for newly activated service index 4
I was trying to find some explanation about these LOGs, but I didn’t have any success.
My questions are:
1. What does this LOG type mean?
2. Does it signalize some issue on the service?
Thanks a lot for the help!
Regards,
Marko

Hi Marko,
Please go through the below link:
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/css11500series/v8.20/configuration/content_lb/guide/ContRule.html#wpmkr1150644
Just pasting some content. Read the details please.
Slowly Starting Connections on a Service
When you configure a content rule with the least connection (leastconn) load-balancing method, a service on the rule with the fewest connections receives the next request. If you activate a service on this rule, the service may become flooded with requests.
To prevent the flooding of connections on a newly activated or reactivated service, you can enable the slow-start feature on a content rule configured with the leastconn load-balancing method. Through this feature, you can configure:
•The rate that an activated service receives connections. The slow-start rate is applied globally to all leastconn content rules on the CSS. By default, the rate is enabled with a default value of 3. If you disable the rate by setting it to 0, the slow-start feature is disabled on all leastconn content rules configured on the CSS.
Note We recommend that you do not change the slow-start rate default value.
•The maximum time that the service remains in the slow-start process. The slow-start timer sets the number of seconds that the service on a leastconn content rule is in the slow-start process. The timer is applied to a leastconn content rule. By default, the timer is disabled. If the timer is disabled, the slow-start feature is disabled on the rule.
When you enable the slow-start feature on the CSS and a leastconn rule, a service on the rule enters the slow-start process when you:
•Add and activate a service to the rule
•Reactivate a service after suspending it on the rule
•Activate the rule
When you activate a rule, it starts to load balance the connections on its services. The service with the least number of connections is selected to enter the slow-start process.
When a rule has only two services, only one service can enter the slow-start process. When the rule has more than two services, a newly activated service can enter the slow-start process when one of the services is currently in the slow-start process and the other services are out of the slow-start process.
A service in the slow-start process slowly continues to receive connections until either the slow-start timer expires or its connections equal the number of connections on the other active services of the rule. Then, the service exits the slow-start process and starts receiving connections as it normally would.
Regards,
Kanwal

What is the appropriate product name for CSS 11500 on Bug Toolkit

Today I tried to search DDTs of CSS 11500 on Bug Toolkit (http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl), however I can not find out appropriate product name corresponding to CSS 11500.
Before I had searched DDTs of CSS 11500 on Bug Toolkit many times, at that time, if my memory correct..
I selected "Cisco CSS 11500 Series Content Services Switches" in the list of "Search for bugs in other Cisco software and hardware products" on Bug Toolkit.
But I can not find this product name today.
Do you know what product name appropriate for CSS 11500 on Bug Toolkit ?
Your information would be appreciated.
Best regards,

Hi Gilles,
Thank you for your cooperation.
Today, I can find the CSS at "new Bug Toolkit".
http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs
Select Product Category: Application Networking Services
Select Product: Cisco CSS 11000 Series Content Services
So I understand I should go "new Bug Toolkit" instead of old "Bug Toolkit" to
search any DDTs for CSS 11500.
Many thanks.
Best regards,

Sorry Server for CSS 11500

Hi,
I have a question regarding sorry server configuration on the CSS 11500 series.
Is there a way for the sorry server to ignore the URL path and always send the user traffic to the "root" page (e.g. index.html) of the sorry server web server?
The problem I have is the redirection of the "root" page (url "/") that is configured for the normal traffic is causing the sorry page not to work since the URL path ("/psp/CUSTOMER1/?cmd=login") does not exist on the sorry page web server:
service Sorry-Server
protocol tcp
port 8000
keepalive type tcp
ip address 192.168.2.254
active
service server1
ip address 192.168.2.101
protocol tcp
keepalive type tcp
port 8080
active
service server2
ip address 192.168.2.102
protocol tcp
keepalive type tcp
port 8080
active
owner Customer1
content Content1
    vip address 192.168.1.101
    port 80
    protocol tcp
    url "/*"
    balance aca
    advanced-balance arrowpoint-cookie
    flow-timeout-multiplier 6
    add service server1
    add service server2
    primarySorryServer Sorry-Server
    active
content Content1-Redirect
    redirect "/psp/CUSTOMER1/?cmd=login"
    vip address 192.168.1.101
    port 80
    protocol tcp
    url "/"
    active
Thanks in advance for your help!
Best regards,
Harry

Hi again,
During a maintenance window I made the following change and that made things a bit better:
service Sorry-Server
type redirect
keepalive type none
redirect-string "192.168.2.254:8000"
active
However, since the redirect string points to a private address, Internet users are not able to access the URL.
As a work-around I sent the redirect to a new content rule with a public address and then configured a second sorry page server:
service Sorry-Server
type redirect
keepalive type none
redirect-string "sorry.example.com:8000"
active
service Sorry-Server-2
ip address 192.168.2.254
protocol tcp
port 8000
keepalive type tcp
active
owner Customer1
content Content2
    vip address x.x.x.x
    add service Sorry-Server-2
    port 8000
    protocol tcp
    active
Is there a better way to do this?
Best regards,
Harry

Cisco CSS 11500 and RDP

Dear NetPros:
Does anyone know that does Cisco CSS 11500 Series Content Services Switch support 'Session Caching of RDP Clients? session for roaming of disconnected sessions' features?
Thanks
Bernard

The Cisco CSS 11500 is a compact modular platform, specifically designed to provide robust Layer 4-7 traffic management services for e-business applications in Internet and intranet data centers.
This URl should help you:
http://www.cisco.com/en/US/netsol/ns340/ns394/ns50/ns254/networking_solutions_package.html

CSS 11500 Certificate Signing Request (CSR)

Would any of you know if and how to configure / general a wildcard or multi-domain SSL certificate on a CSS 11500 appliance? The "SSL gencsr ..." command doesn't seem to allow me to add more than one domain name during the information gathering.
Any help or input would be greatly appreciated.
Thanks,

WildCard certs are supported on CSS.
The only thing that makes it a CSR for a wildcard certificate would be that the common name would be something like "*.yourdomain.com".
Since a wildcard certificate represents multiple domains, it can be re-used on the
multiple https content rules of different IPs.
The CSR procedure for a wildcard certificate on the CSS is not different than the CSR
procedure for a regular certificate (You just need to put something like "*.yourdomain.com" in front of common name):
CSS11506(config)# ssl gencsr app1key
Country Name (2 letter code) [US]US
State or Province (full name) [SomeState]CA
Locality Name (city) [SomeCity]San Jose
Organization Name (company name) [Acme Inc]Yourdomain Inc.
Organizational Unit Name (section) [Web Administration]SSL Admin
Common Name (your domain name) [www.acme.com]*.yourdomain.com
Syed

CSS 11500 - Support IPV6

Does the 11500 series support IPV6? If so, what code level was it first introduced in? If not, when will it be supported? Thank you!

not supported and will never be on the CSS.
A new device will be created and it will come with many new features including ipv6 support in hardware.
Gilles.

Users losing session on 11500 series Content switches

What would cause users to loose session connection on the 11500 series switches.Arrowpoint cookies are been used.

the CSS has an aggressive way of destroying idle connection.
If a connection stays idle for 8 sec, the CSS mark it has idle.
Once marked idle, a connection will stay idle forever for the CSS - even if traffic is still going on between client and server.
So at some point of time, the CSS will decide to reuse the memory used to switch a connection marked idle.
At this time, the user will lose his session.
The solution is to increase the idle timeout.
The command is 'flow-timeout-multiplier' and you configure it per content rule.
Give it a try with a timeout multiplier of 20 and see if this improves the situation.
You may have to increase the value.
Gilles.

CSS 11500 Responds for any Port

Hopefully this is an easy question but I am having a heck of a time finding an answer.
We have multiple CSS 11500 clusters. We have found that on all of them, if you try to open a session on any port to an IP address on the backend of the CSS, the CSS will complete the SYN-ACK-ACK session with the client. This happens regardless of whether there is something on that IP address or not.
Example:
Front Back
10.1.1.0/24 --- CSS --- 10.2.2.0/24
Coming from any IP, if I try to telnet to ANY IP on the 10.2.2.0 subnet (whether or not there is an actual server on that IP) on any port (whether or not that port is open or not), the CSS will complete the initial connection. I have verified this using telnet to numerous ports and viewing the transaction in a packet capture.
Is there any way to shut this off? This is causing some licensing issues for our security folks that use a vulnerability scanner licensed on number of IP addresses.
Thanks for any input!

Thanks for your reply Marvin.
We actually use ACLs already - primarily for purposes of allowing backend servers to reach load-balanced services on the CSS they sit behind or for reverse proxy services.
I have tried specifically blocking access to backend IP addresses that are not used but oddly enough the CSS still replies and opens the initial TCP session just like any other.
I think I'm going to have to open a TAC case on this one. If they can't answer it, I may be forced to put all of these behind firewalls - which is doable but not ideal.

Changing Max-Connections in CSS 11500

I have an architecture with two 11500 in active-passive mode and receive 800 connections every 5 minutes.
Could appear secondaries effects if i change the default of max-connections in CSS 11500 for example to 1200?
One of the risks i want to avoid is with this change, the CSS could be crashdown because of the drop of connections..

Good morning,
Could you please let me know what is the exact parameter you are talking about?
From what you described, I believe you may be referring to the "max connections" parameter configured under the services. This command just limits the number of concurrent connections that are allowed on a specific real server to ensure that the server itself doesn't get overloaded. Increasing this limt would not have any negative effect on the CSS itself, but, since you are allowing more simultaneous connections on the server, you may experience resource issues on the server itself.

A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (p

A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that
the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)(Microsoft SQL Server, Error: 2)
The system cannot find the file specified
Cannot connect to COWBOYS.
Here are the technical details===================================
A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider:
Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft%20SQL%20Server&EvtSrc=MSSQLServer&EvtID=2&LinkId=20476
Error Number: 2
Severity: 20
State: 0
Program Location:
at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection, Action`1 wrapCloseInAction)
at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj, Boolean callerHasConnectionLock, Boolean asyncClose)
at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, Boolean withFailover)
at System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean ignoreSniOpenTimeout, TimeoutTimer timeout, Boolean withFailover)
at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance, SqlConnectionString connectionOptions, SqlCredential credential, TimeoutTimer
timeout)
at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(TimeoutTimer timeout, SqlConnectionString connectionOptions, SqlCredential credential, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance)
at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, SqlCredential credential, Object providerInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance,
SqlConnectionString userConnectionOptions, SessionData reconnectSessionData)
at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, DbConnectionPoolKey poolKey, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionFactory.CreateNonPooledConnection(DbConnection owningConnection, DbConnectionPoolGroup poolGroup, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionFactory.TryGetConnection(DbConnection owningConnection, TaskCompletionSource`1 retry, DbConnectionOptions userOptions, DbConnectionInternal oldConnection, DbConnectionInternal& connection)
at System.Data.ProviderBase.DbConnectionInternal.TryOpenConnectionInternal(DbConnection outerConnection, DbConnectionFactory connectionFactory, TaskCompletionSource`1 retry, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionClosed.TryOpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory, TaskCompletionSource`1 retry, DbConnectionOptions userOptions)
at System.Data.SqlClient.SqlConnection.TryOpenInner(TaskCompletionSource`1 retry)
at System.Data.SqlClient.SqlConnection.TryOpen(TaskCompletionSource`1 retry)
at System.Data.SqlClient.SqlConnection.Open()
at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.ValidateConnection(UIConnectionInfo ci, IServerType server)
at Microsoft.SqlServer.Management.UI.ConnectionDlg.Connector.ConnectionThreadUser()
===================================
The system cannot find the file specified
I have tried from so many forms. This is so frustrating. Thank for everyone/anyone who wants to help. So this is what happened: I had to uninstall my previous sqlserver 2012(which worked great) for some reason, and I uninstalled everything from that download.
Then I installed the trial edition of sql server 2012 (64 Bit) and It wouldn't connect to the database. (Error mentioned above.) My local DB is COWBOYS. (COWBOYS is also my computer name.) After this, I have tried downloading sqlexpress and sqlserver 64bit
many times and cannot connect to my local DB.
How do I connect to my Local DB?
Also, I think this might help: (When I run sqlserve.exe, which I was able to find in C:\Program Files\Microsoft SQL Server\110\LocalDB\Binn, I get an error: Your SQL server installation is either corrupt or has been tampered with(Error getting
instance ID from name). Please uninstall then re-run setup to correct this problem.
I would happily re install it, if it wasn't my 20th time.
I don't have any remote connections, I don't use username/password, only window authentication. I work mostly on visual studio, but without able to store /retrieve data, I don't know how to survive.
May be the solution is very simple, but I am too frustrated.
Some of the things I have tried:
From a command prompt, enter one of the following commands:
net start "SQL Server Agent (MSSQLSERVER)" OR
net start "SQL Server Agent(instancename)"(for instance)
on my sql configuration, I cannot start anything because there is nothing there to start. I can post more details, if that would help. Also, some more details about the error:
Details
Product:
SQL Server
ID:
2
Source:
MSSQLServer
Version:
10.0
Component:
SQLEngine
Message:
An error has occurred while establishing a connection to the server. When connecting to SQL Server, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. (provider: Named Pipes Provider, error:
40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
Explanation
SQL Server did not respond to the client request because the server is probably not started.
User Action
Make sure that the server is started.
Version:
9.0
Component:
SQLEngine
Message:
An error has occurred while establishing a connection to the server. When connecting to SQL Server 2005, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. (provider: Named Pipes Provider, error:
40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
Explanation
SQL Server did not respond to the client request because the server is probably not started.
User Action
Make sure that the server is started.
Any one that can help me, I will be greatful. Thank you so much. p.s. please ask me anything if you have any questions.

It sounds like there are a couple things going on here. First check if you have a successful install of SQL Server, then we'll figure out the connection issues.
Can you launch SQL Server Configuration Manager and check for SQL Server (MSSQLSERVER) if default instance or SQL Server (other name) if you've configured your instance as a named instance. Once you find this, make sure the service is started.
If not started, try to start it and see if it throws an error. If you get an error, post the error message your hitting. If the service starts, you can then launch SSMS and try to connect. If you have a default instance, you can use the machine
name in the connection dialog. Ex: "COWBOYS" where Cowboys is the machine name. However, if you named the SQL Server instance during install, you'll need to connect using the machine\instance format. Ex: COWBOYS\Romo (where Romo
is the instance name you set during install).
You can also look at the summary.txt file in the SQL Server setup error logs to see what happened on the most recent install. Past install history is archived in the log folder if you need to dig those up to help troubleshoot, but the most
recent one may help get to the bottom of it if there is an issue with setup detecting a prior instance that needs to be repaired.
Thanks,
Sam Lester (MSFT)
http://blogs.msdn.com/b/samlester
This posting is provided "AS IS" with no warranties, and confers no rights. Please remember to click
"Mark as Answer" and
"Vote as Helpful" on posts that help you. This can be beneficial to other community members reading the thread.

Unable to allow remote control and deny transfer files in RM

Hi, we're running ZCM 11 SP1 and I have a question about assiging rights to non-Helpdesk users for remote control only for user application support. It looks like if I deny transfer files that the button for remote control automatically changes from allow to deny. I couldn't find anything in the forums, KB, or docs to see if this is working as intended or a bug of some sort? If intended, do you know why remote control and transfer files go together, just curious? In ConsoleOne versions of remote management we had always limited non-Helpdesk remote operators and were hoping to do exactly the same with ZCM11. Thanks.

Originally Posted by spond
Newellt,
I can't see why it would be necessary, I suggest you open a Service
Request and complain!
Shaun Pond
Was there ever a workaround for this? I'm seeing the same behavior in 11.2.3 and we have a need to block file transfer but allow remote management.

After restoring SharePoint farm backup ( The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connection)

Hi,
I have taken farm back and restore it in new UAT environment, while access to the main site getting the below error:
Error
An unexpected error has occurred.
Troubleshoot issues with Microsoft SharePoint Foundation.
Correlation ID: 866476f3-23dd-4e1e-97af-bffc62cc2d57
Date and Time: 7/15/2014 11:26:35 AM
When i checked in log i got below error
System.Data.SqlClient.SqlException: A network-related or instance-specific
error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40
- Could not open a connection to SQL Server) at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject
stateObj) at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecu...
Thanks in advance
Said Al Balushi

Hi Wendy,
i have checked all below points, every thing is fine but still i am getting the same error.
Check SQL services are runing
Check remote conenctions are enabled
Check SQL Browser service is runing
Check TCP/IP protocal enabled at SQL server
Check out windows firewall setting
Thanks,
Said

Do CSS 11500 series allow remote SPAN?

Similar Messages

Maybe you are looking for