Do I have a K7N2 Delta-ILSR????

Its my understanding that the K7N2 Delta-ILSR has the MCP2-T chip, but the chip I have where the MCP2-T should be has a label on it that says "MSI 400 FSB". So is this mobo a K7N2 Delta-ILSR or not? The only thing that I find printed on it is K7N2 and MS-6570 Ver 1.
Thanks for any help.
MM

Quote from: osnavi on 21-September-05, 12:08:48
Then ? What about the MAX AMPS. asked ?
Yes you did ask for the AMP ratings. I spent 29 years trouble shooting high-end solid state equipment where incorrect voltages wreak havoc on IC chips so I assumed that is what you really wanted to know.
A power supply is going to handle the required current or its not. If it can't handle it, shuts down. (Isn't there a question on the A+ certification test that address this? Jack adds a hard and the PC won't power up. Why? Answer: C. The power supply is too small.) So why is Max AMP so important in trouble shooting my problem? I also think that Dr. Stu's Statement "if there is not enough current on the 12v rail, then the CPU cannot start" is incorrect. Basic ohms law: you need VOLTAGE and a LOAD (CPU) first to have current.
The max AMP rating for my PU is as follows +3.3v=35amp, +5v =28amp, and +12v= 22amp. The supply is out of an Avaya sever cabinet with no brand name on it. As I posted in an early post, "The power supply tests good". This is an assumption that I made because I just built a Pentium 3.4Gig a few days before I took on this project. But just to be sure I got out my oscilloscope with a current probe and a load box (light bulbs and a potentiometer) and tested each supply lead. The amp's far exceeded the ratings before the PU shut down each time.
So now back to my question from an early post: My POST card is telling me that the BIOS is stuck in "Reset" Does the BIOS get the reset from the CPU or does it come from the external short?

Similar Messages

K7N2 DELTA-ILSR AND DDR-RAM

I got K7N2 Delta-ILSR, the last bios version, and
2x256 twinmos pc3200 ram. The 50% of the times the computer startes without problems, but the other 50% it gets hang up when I start the computer and the "d-Leds" indicate:" the memory module is damaged or not installed properly".
I know that the ram-modules works, but not with this Motherboard.
I need to get new ram-modules.
Somebody have the K7N2 DELTA-ILSR, with ddr-ram that works ??? (not K7N2G- IL and ILSR)
[size=15]You can list this here, it will help a lot of people! [/SIZE]

If you'll look at the start of the forum you'll see an article "good memory choices" start there.If you don't want to spend the bucks buying new mem read this http://www.msi.com.tw/program/e_service/forum/index.php?threadid=20221&boardid=14

K7N2 Delta ILSR memory problem

I have a K7N2 Delta ILSR board with Athlon XP 2500 with 2 Gig of Mushkin Black Line ram (the ones that are
suppose to be CL2). I change the FSB to 200, and my memory won't run at CL2. Want to raise the Dram voltage
to 2.8V to see if it would make a difference. I looked all over this site for the modded bios 7.8. Does anyone
have the modded bios??? Any help would be appreciated.......

He/She overclocked the 2500+, to make it become a 3200+. Done it myself, but it mostly works with the first step of the 2500+. - That means the overclock forum.
Well, CAS 2 is a very tight timing, which I don't think is possible. In general on Socket A systems:
- FSB 133/266 --> CAS 2 or 2.5
- FSB 166/333 --> CAS 2.5
- FSB 200/400 --> CAS 3

K7n2 delter ilsr raid

i have a k7n2 delter ilsr but i seam to be unable to use its raid when i add a harddrive to it keeps saying bios not installed is there anyway in removing it or is there a nack to as theres nothing in the manuel for it. ???? ?(

hi
my knowledge of raid is limited
the sata connectors and ide3 is part of raid.
if you add or remove any drive you have to define a new drive array.
when it says no bios it means no drives are connected.
atleast its why i get that message on my promise ultra100 tx2 ide controller card.
you have to push a certain button to get into raid bios.
bye

Athlon Xp 2500+ on k7n2 delta-ilsr

i have the k7n2 delta ilsr mobo and i just recently installed a athlon xp 2500+ but my mobo only detects a 1900+ if you know how to fix this problem i would appreciate it. thanks.

yes i did. i did what they told me too and still its on only running at 1900+

AGP Setup For k7n2 delta ilsr

I have a k7n2 delta ilsr mb, in display properties on desk top setting tab then advanced button then GeForce tab under adapter information is Bus and memory. To the right of Bus it reads AGP (PCI mode) shouldn't that read AGP (8X), how can I change this. Ron.

Hi,
No, leave it at 64 or 128.
Go here for an explanation:
http://www.rojakpot.com/default.aspx?location=7&var1=18
Then - Click on: "Free Access To the BIOS Optimization Guide" near the bottom of the page - then click on "AGP Aperture Size"
Axel

Win XP problem w/k7n2 delta ilsr

I forgot to put this in my first post. I have a k7n2 delta ilsr and I'm using win xp pro. In device manager under Other Devices it reads:
? ethernet controller
? raid controller
? sm bus controller
? universa serial bus usb controller
Did I forget to install or setup something.
Thanks, Ron.

Hi,
Yes, you should install the nForce drivers for your board:
The latest ones are here:
http://www.nvidia.com/content/drivers/drivers.asp
Axel

Need help with jumper settings for k7n2 delta ilsr

I have a k7n2 delta ilsr and I'm using a AMD 2800+ barton 333 fsb. I'm not sure what the jumper settins are for this cpu. The users guide only shows 133/166 and 200, can anyone help me with the jumper settings.
Thanks, Ron.

Hi,
As your processor is 333FSB - the jumper should be set to 166FSB as should the BIOS. As your RAM CPU combination runs at 2x166=333 or thereabouts.
Basically, as a general rule, if you halve the FSB speed of your processor you'll get the setting for both BIOS and Jumper. 200FSB=100, 266FSB=133, 333FSB=166 etc. etc.
Axel

Sata boot with K7N2 Delta-ILSR

I have a K7N2 Delta-ILSR board and can't load the os to the sata drives. Both drives are new and raid 0. The load sees no drives and the raid drives don't show in the boot device menu in the bios. What have I missed? Is this possable?
Thanks for any help,
Mike

so you made the array control plus f i assume
have you set scsi second to cdrom
then hit f6 as xp install starts
and feed in drivers

1st boot probs with k7n2 delta ilsr

1st build, 1st boot error
NVIDIA Boot Agent, PXE-2.0 (build 082 V1.82)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting NVIDIA Boot Agent.
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER
i have a k7n2 delta ilsr
amd athlon xp 2500+ 1.83ghz 333 fsb
maxtor diamondmax+9 120 gb sata
kingston ddr333 pc2700 cl 2.5
sapphire radeon 9700 pro atlantis 128 mb ddr
if anyone can help i would greatly appreciate it!

Quote
1st build, 1st boot error
NVIDIA Boot Agent, PXE-2.0 (build 082 V1.82)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting NVIDIA Boot Agent.
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER
i have a k7n2 delta ilsr
amd athlon xp 2500+ 1.83ghz 333 fsb
maxtor diamondmax+9 120 gb sata
kingston ddr333 pc2700 cl 2.5
sapphire radeon 9700 pro atlantis 128 mb ddr
if anyone can help i would greatly appreciate it!
You first need to make sure you have the promise controller drivers installed for it to recognize the hard drive. The system should have came with a floppy disk with the drivers on it........Make sure your boot order is floppy drive/cdrom drive/sata/scsi........boot to the XP cd after you have the sata controllers installed......then run the XP disk setup partion/format/install.........after installation you can set boot order as sata/scsi as first boot device.

Best Cooler For XP 3000+ on K7N2-Delta ILSR?

As the title suggests I am looking for a good, high performance Heatsink and Fan for my current XP 3000+ system. I have a K7N2 Delta ILSR mobo. Three Heatsinks I have been looking at are:
Thermaltake Volcano 12 Extreme
Thermalright SLK-900A with a Vantec Tornado 92mm fan
Thermaltake SilentTower - (I think this one requires holes in the Mobo which the K7N2 Delta ILSR doesn't have :( Please correct me if I am wrong).
I am looking for a high-performance heatsink at an affordable price (max £50) with which I can do some overclocking. Currently I have one of the Zalman ones ( I think it is a CNPS6000-CU) which is insufficient (load temps 66 C). Help would be much appreciated. Thanks in advance.

Yeah, i'm looking for a good price vs performance vs noise solution really. Both the Volcano and the Vantec Tornado are really loud, but they seem to perform quite well.

K7n2 delt ilsr instabilty problem update

have a k7n2 delta ilsr have an issue where it is unstalble ie get bsod at welcom etc at 400 fsb ie 200 setting in bios will run at 166 in safe mode the 3200 cpu is reconised as at 2.39 ghz it should be 2.2 ghz if i run cpucz it says the multiplier is *12 is this a motherbord fault have updated bios too 7.8 latesed have tried diff make of memory power supply but i think the problem is looking me in the face in the fact that the cpu is reconised as 2.39 ghz and the muilt is *12 i think it should be * 11 can any body help regards bazer

yes has latesd bios    AMD Athlon(tm) XP 2700+ here is some info pc wizard 2005
Codename :   Barton
Revision :   A2
Technology :   0.13µ
CPU ID :   6.A.0
CPU IDEx :   7.A.0
Features :
VME - Virtual Mode Ext. :   Yes
DE - Debugging Extension :   Yes
PSE - Page Size Extension :   Yes
TSC - Time Stamp Counter :   Yes
MSR - Model Specific Registers :   Yes
PAE - Physical Address Extension :   Yes
MCE - Machine Check Exception :   Yes
APIC - Local APIC Built-in :   Yes
SEP - Fast System Call :   Yes
MTRR - Memory Type Range Reg. :   Yes
PGE - Page Global Enable :   Yes
MCA - Machine Check Architecture :   Yes
PAT - Page Attribute Table :   Yes
PSE36 - 36-bit Page Size Extension :   Yes
PSN - Unique Serial Number :   No
DS - Debug Trace & EMON Store :   No
ACPI - Software Clock Control :   No
SS - Self Snoop :   No
TM - Thermal Monitor :   No
HTT - Hyper-Threading :   No
SBF - Signal Break on FERR :   No
MON - Monitor/Mwait :   No
DSCPL - CPL qualified Debug Store :   No
TM2 - Thermal Monitor 2 :   No
CID - Context ID :   No
EST - Enhanced SpeedStep Tec...   No
NX Bit - No-execute Page Protec...   No
VMX - Vanderpool Technology :   No
Miscellaneous :
FPU - Co-processor Built-in :   Yes
CX8 - CMPXCHG8B :   Yes
CX16 - CMPXCHG16B :   No
CMOV - Conditionnal Move Inst. :   Yes
CLF - Cache Line Flush :   No
FXSR - Fast Float Save & Restore :   Yes
DAZ - Denormals Are Zero :   No
MMX Technology :   Yes
SSE Technology :   Yes
SSE2 Technology :   No
SSE3 Technology :   No
X86-64 Technology :   No
AMD MMX Technology :   Yes
3DNow! Technology :   Yes
Extended 3DNow! Technology :   Yes
3DNow! Pro Technology :   Yes
SMP - MP Capability :   No
Power Status :
Voltage Control :   No
Frequency Control :   No
Thermal Sensor Built-in :   Yes
Addressing Information :
Physical Addressing max. :   34-bit
Linear Addressing max. :   32-bit
Mainboard Upgradebility :
Socket/Slot :   Socket A
Upgrade interface :   ZIF Socket
Supported Speed :   2200 MHz (or more)
Supported Voltage :   1.6V
al Information :
Performance Rating :   PR-3300 (estimated)
Real Frequency :   2164.89 MHz
Multiplier :   12x
Front Side Bus Information :
FSB Frequency :   180.4 MHz
Bus Speed :   360.8 MHz (DDR)
Initial Frequencies :
Frequency :   2000 MHz
FSB Frequency :   166 MHz
Control Clock Frequency :
Type :   None
Thermal Information :
Core Power :   63.42 W (estimated)
Resistance :   0.46 °C/W (estimated)
Processor Performance Information :
Throttle Mode AC :   None
Throttle Mode DC :   Adaptive
Current Configuration :   None
Throttle :   2164 MHz
CPU Throttle Temperature :   60°C
CPU Shutdown Temperature :   100°C
eneral Information :
A0 (RAS 0) :   256 (Single Bank)
A1 (RAS 2) :   256 (Single Bank)
A2 :   Empty
Memory Controller Information :
Memory Controller :   Standard, EDO
Number of connectors :   3
Max. Module Size :   32 MB
Max. Memory Size :   96 MB
Supported Speed :   70ns, 60ns
Supported Voltages :   5v
Error Detection Method :   8-bit Parity
Error Correction Capability :   Unspecified
Current/Supported Interleave :   1-way/1-way
Chipset Information :
Type :   DDR-SDRAM PC2900
Frequency :   180 MHz
FSB/RAM Multiplier :   1/1x
Channels :   Dual
ECC Diagnostic :   No
CAS Latency (tCL) :   3 clocks
RAS to CAS (tRCD) :   3 clocks
RAS Precharge (tRP) :   3 clocks
Cycle Time (tRAS) :   8 clocks
Information SPD EEPROM (A0) :
Manufacturer :   Samsung
Part Number :   M3 68L3223ETM-CCC
Serial Number :   F6016243
Type :   DDR-SDRAM PC3200 (200 MHz)
Size :   256 MB (1 rows, 4 banks)
Module Buffered :   No
Module Registered :   No
Width :   64-bit
Error Correction Capability :   No
Max. Burst Length :   8
Refresh :   Reduced (.5x)7.8 µs, Self Refresh
Voltage :   SSTL 2.5v
Supported Frequencies :   166 MHz, 200 MHz
CAS Latency (tCL) :   2.5 clocks @166 MHz, 3 clocks @200 MHz
RAS to CAS (tRCD) :   3 clocks @166 MHz, 3 clocks @200 MHz
RAS Precharge (tRP) :   3 clocks @166 MHz, 3 clocks @200 MHz
Cycle Time (tRAS) :   7 clocks @166 MHz, 8 clocks @200 MHz
Information SPD EEPROM (A1) :
Manufacturer :   Samsung
Part Number :   M3 68L3223ETM-CCC
Serial Number :   F6056193
Type :   DDR-SDRAM PC3200 (200 MHz)
Size :   256 MB (1 rows, 4 banks)
Module Buffered :   No
Module Registered :   No
Width :   64-bit
Error Correction Capability :   No
Max. Burst Length :   8
Refresh :   Reduced (.5x)7.8 µs, Self Refresh
Voltage :   SSTL 2.5v
Supported Frequencies :   166 MHz, 200 MHz
CAS Latency (tCL) :   2.5 clocks @166 MHz, 3 clocks @200 MHz
RAS to CAS (tRCD) :   3 clocks @166 MHz, 3 clocks @200 MHz
RAS Precharge (tRP) :   3 clocks @166 MHz, 3 clocks @200 MHz
Cycle Time (tRAS) :   7 clocks @166 MHz, 8 clocks @200 MHz

[nForce] K7N2 Delta ILSR - Do i have to have raid with sata drive

Hi guys,
Probably a really stupid question, but here goes
My machine has 1 ide HDD and 1 SATA HDD.
The SATA drive is set up as raid0 and is purely used as a data disk. The OS(win xp pro sp1) is on the IDE drive
The only way i could get the SATA HDD recognised by windows, was to set up a raid array with just the 1 disk.
Pretty useless raid array i know.
Did i have to do this or is there a way to have the sata hdd usable without having to set up a raid array
Thanks
John L
MSI K7N2 DELTA ILSR
ATHLON XP 2500 Barton
2X512 MB PC3200
Leadtek GF4mx460
WD 8MB CACHE 80Gb IDE
Samsung 120Gb Sata

you have to do it for the controller to work
but it has no effect on the drive
you can move a regular drive on ide 3 back to a normal ide and its all fine

Someone plz help me with my k7n2 delta-ilsr

Hey everyone,
I just put my sytem togother and ran into a problem. I got the system to boot up just fine. It was not until I tried installing windows xp proffesional that I ran into problems. The installation process runs pretty smoothly, until the computer reboots to run windows for the first time. After it reboots the windows logo appears and the after 2 seconds or so, a blue screen appears saying that windows was shut down to prevent any damage to my computer. I have never encountered this problem before when I built other systems. The screen suggests that I should check my HDD's for viruses or check to see if they are configured correctly. The HDD's are SATA and I have them set up in RAID 0 mode and yeah I installed the RAID drivers during the installation process. Thinking that I had made mistake setting up the SATA drives, tried installing windows using a regular IDE hard drive and it gave the same message. I am stumped anybody have any ideas of what I might be doing wrong? Any help would be appreciated . My system specs are below.
MSI k7n2 delta-ilsr mobo
AMD 3000+ Athlon XP cpu (333 fsb)
ATI Raedon 9000 ( I know it's crappy , I'm still saving up for the ATI all in wonder 9800 )
x1 kingston 512mb pc3200 DIMM
x2 maxtor 80gb maxtor hdd's
x1 regular cd-rom drive
x1 floppy drive
420w raidmax psu
(+3.3v = 26A, +5v = 32A, +12v=13A)

Memory that comes with timing of 5 2 2 2 or 6 2 2 2 or usally winbond BH-5 memory chips. Ones with 5 3 2 2 or CH-5 winbond chips. The BH-5 chips overclock a little better than the CH-5. (Muskin uses BH-5 winbond in there black ram)
Winbond is no longer making BH-5 chips but is going to make a limited run of them as demend is high for them.
The first number shown here is the Traz and it controls the flush timing bench testing is showing that a higher number of 9, 10 or 11 or getting better bench results than the 6 or 5. Thats with Dual Channel memory.
The timing you show probly should be something like 8 3 3 3 or 8 3 3 2.5 unless it is there faster Dual channel ram.
The timing numbers can also appear like this 2 2 2 5 the high number is the Traz either way.
Look on your memory manufactor web site for the timing that if should run at also look at the voltage as this can make a big differance.

HELP me with my K7N2 delta ilsr

Can anyone help me with this problem. I have just upgraded to MSI's K7N2 delta ilsr motherboard. Its all working quite well apart from the fact that the pc wont start up from cold....at all.
When I start the pc from an off state, it runs up the fans and drives, but does not post.
The diagnostic led pannel on the back of the pc shows that the cpu is faulty or not installed correctly.
If I then press the reset button, the pc posts, and boots up just fine.
It does this EVERY time I start up.
I have tried re installing the cpu, which is an XP 2800+ 333 barton, but to no avail.
I have asked a few questions on other forums, but I cant solve it.
These are the suggestions so far.
1. the psu (I have a Tsunami 400 atx psu) could not be giving out enough power on initial startup, but once the pc is running, it has enough to boot the pc from a reset.
2. The mobo or the bios could be at fault. I have not flashed the bios, or upgraded it in any way from original, so is there an issue with the original bios on these boards, and 2800 barton chips??? Could it be a mobo fault? The pc runs fine once the machine is booted.? how do I test it?
3. The cpu could be faulty? but would this not stop it running fuull stop?
4. my ram. I have a single stick of OCZ 512mb pc3200 ddr, which I was told would make the pc fly. Not shure on that statement, but is this ram compatible?? could this be the problem?
Im fairly new to the upgrade side of things, and I need some help with this one.
Also, Id be really greatfull if some one could talk me through flashing my bios to the latest version, as the thought of doing this narks me a bit...I dont want to mess it up and get a dead pc...
HELP

+3.3v 14A
+5v 28A
+12v 16A
+5vsb 2A
-5v 0.5A
-12v 0.8A
Hope this helps, as my pc seems to be living with its case off a lot these days..haha

Do I have a K7N2 Delta-ILSR????

Similar Messages

Maybe you are looking for