Do I have an upgrade path?
Hello,
Here is my situation: My wife and I just bought a new home. She has an older G4 PowerMac (400MHz). We also have an Airport Base Station (Snow) that I use wirelessly for my PowerBook G4. Unfortunately, her desk is located a long ways away from any wired connectivity. Thus, I need to find a wireless solution for her old G4.
Question: Is there a way to continue using my Apple Airport Base Station (Snow) which has a wired connection to the Internet and EXTEND the wireless connection to a device (Airport Express?) that I could locate near her desk and then simply plug in her PowerMac G4's ethernet port?
In other words, I'd like to just be able to just plug her G4 into the Aiport Express via wired connection and then have the Airport Express be able to relay data connectivity wirelessly back to my Snow ABS located in another room.
Will that work? Is this possible? If not, is another setup similar to this possible?
Thanks for any help...
-Tige
TigeMac: I think you and Duane have "crossed signals" in this discussion.
What you want to do is use an Airport Express as device that you could cable to the PowerMac's ethernet port, to provide wireless network access to that PowerMac. The Airport Express is only capable of being used in that manner when it is configured to "extend" the wireless network of another Airport Express device or an Airport Extreme Base Station. Your older Snow Base Station, on the other hand, cannot have its wireless network "extended" by an Airport Express device.
See also your other discussion on this topic at:
TigeMac, "Is this possible? Getting conflicting advice...", 10:19pm Sep 21, 2005 CDT
Similar Messages
-
I have a copy of Motion I have never used but mean to get started. Info says Motion v2.0.1 I don't know if this is Motion 2 or what, the handbook just says Motion. I think 3 is out. Do I have an upgrade path without buying Final Cut which I don't need? Is 3 a lot better? I'm using a G5 iMac with 1.5Gb of RAM and its 1.6Ghz - will this perform?
Thanks for your help guysThe only way to get Motion3 is to buy an upgrade for FCS I'm afraid.
Motion performance will depend on your graphics card you have in your iMac
System requirements are here:-
http://www.apple.com/finalcutstudio/specs.html
hope that helps
Peter -
Usually there is a upgrade path for current users of the software at a reduced price. I dont see anything like that for Lightroom 6. Will I have to pay full price just to upgrade to the new LR6 standalone version???
The standalone upgrade is 79 US Dollars.
Go to Products, select Lightroom 6, click on Buy, select Upgrade instead of Full -
Hi, I am a Lightroom user and currently have 5.6 version (DVD Version). The lightroom 6 version, for existing lightrrom users, is there an upgrade path or it is a new software entirely. In either cases, what costs are associated.
Thanks,
RajLR 6 is a new payfor upgrade, $80 in the US if you have the serial-number-licensed LR 5. If you're already using the CC version of LR+PS then it just comes along as a new app you can install.
It’ll run alongside your LR5 so you can try it out and see if it’s something you want.
The only trial is a LR-6-CC version that you can convert to a serial-number-licensed version if you buy a serial-number. I think the download in LR 5 when it notifies you of an upgrade is what you can use to try it, although I don’t have personal experience with that seeing as I have the CC version of LR+PS so the CC App provided the Install button for me.
The main issues people are having are for some system configurations performance is worse. Adobe rewrote it to use the GPU in the Develop module but some people’s video cards aren’t up to the task, and for some people even turning off the GPU, while speeding things up, doesn’t make it as fast as LR 5.
On my system it seems to work great. -
Upgrade from SCCM 2012 SP1 CU4 to R2 Fails - Unsupported Upgrade Path
Hi everybody,
I'm currently upgrading our SCCM infrastructure to SCCM 2012 R2 after have finished with the upgrade from SCCM 2012 RTM to SP1 CU4, thus far everything works fine, but when I try to update any
of the site servers, whether CAS or Primary, I'm getting the following error message in the Prerequisites Check:
I've gone through the system requirements and prerequisites over and over again and I can assure you that every possible update, supported OS, feature set, SQL Server, check list, etc,
etc, have been followed as per the official documentation available, however I'm stuck in this point, and surely enough I haven't been able to find out a similar case.Additionally I'm adding
the ConfigMgrPrereq log (the relevant portion of it) in case someone could kindly take a look at it.
<04-25-2014 02:06:46> ******* Start Prerequisite checking. *******
<04-25-2014 02:06:47> ********************************************
<04-25-2014 02:07:00> INFO: Detected current installed build version [7711] for sitecode [BRA]. For Upgrade,
minimum supported installed build version is [7804].
<04-25-2014 02:07:00> INFPROSCCMCMS.usersad.everis.int;
Unsupported upgrade path; Error;
Configuration Manager has detected that one or more sites in the hierarchy are installed with a version of Configuration Manager that is not supported for upgrade.
<04-25-2014 02:07:00> INFO: This rule only apply to primary site, skip checking.
<04-25-2014 02:07:00> INFPROSCCMCMS.usersad.everis.int;
Active Replica MP; Passed
<04-25-2014 02:07:00> INFO: This rule only applies to primary or secondary site in hierarchy, skip checking.
<04-25-2014 02:07:00> INFPROSCCMCMS.usersad.everis.int;
Parent site replication status; Passed
<04-25-2014 02:07:00> <<<RuleCategory: Database Upgrade Requirements>>>
<04-25-2014 02:07:00> <<<CategoryDesc: Checking the target ConfigMgr database is ready to upgrade...>>>
<04-25-2014 02:07:00> ===== INFO: Prerequisite Type & Server: SQL:INFPROSCCMCDB.usersad.everis.int
=====
<04-25-2014 02:07:00> <<<RuleCategory: Access Permissions>>>
<04-25-2014 02:07:00> <<<CategoryDesc: Checking access permissions...>>>
<04-25-2014 02:07:00> INFPROSCCMCDB.usersad.everis.int;
SQL Server sysadmin rights; Passed
<04-25-2014 02:07:00> INFPROSCCMCDB.usersad.everis.int; SQL Server sysadmin rights
for reference site; Passed
<04-25-2014 02:07:00> INFO: CheckLocalSys is Admin of <INFPROSCCMCDB.usersad.everis.int>.
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
Site server computer account administrative rights; Passed
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
SQL Server security mode; Passed
<04-25-2014 02:07:09> <<<RuleCategory: System Requirements>>>
<04-25-2014 02:07:09> <<<CategoryDesc: Checking system requirements for ConfigMgr...>>>
<04-25-2014 02:07:09> INFO: OS version:601, ServicePack:1.
<04-25-2014 02:07:09> INFO: Target computer is a Windows server.
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
Unsupported site server operating system version for Setup; Passed
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
Domain membership; Passed
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
Pending system restart; Passed
<04-25-2014 02:07:09> <<<RuleCategory: Dependent Components>>>
<04-25-2014 02:07:09> <<<CategoryDesc: Checking dependent components for ConfigMgr...>>>
<04-25-2014 02:07:09> INFO: Return code:0, Major:10, Minor:50, BuildNum:4000
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
SQL Server version; Passed
<04-25-2014 02:07:09> INFO: Get Sql edition:Enterprise Edition.
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
SQL Server Edition; Passed
<04-25-2014 02:07:09> INFO: Checking Tcp is enabled to Static port, SQL Server:INFPROSCCMCDB.usersad.everis.int,
Instance:.
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
SQL Server Tcp Port; Passed
<04-25-2014 02:07:09> INFO: Checking if SQL Server memory is limited.
<04-25-2014 02:07:09> INFO: SQL Server memory is limited.
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
Configuration for SQL Server memory usage; Passed
<04-25-2014 02:07:09> INFO: Checking if SQL Server memory is configured to reserve minimum memory.
<04-25-2014 02:07:09> INFO: Installing the central administration site or primary site, requires SQL
Server to reserve a minimum of 8 gigabytes (GB) of memory.
<04-25-2014 02:07:09> WARN: SQL Server minimum memory is 8000 MB.
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int; SQL Server process memory allocation;
Warning; Configuration Manager requires SQL Server to reserve a minimum of 8 gigabytes (GB) of memory for the central administration site and primary site and a minimum of 4 gigabytes (GB) for the secondary site. This memory is reserved by
using the Minimum server memory setting under Server Memory Options and is configured by using SQL Server Management Studio. For more information about how to set a fixed amount of memory, see
http://go.microsoft.com/fwlink/p/?LinkId=233759.
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
Case-insensitive collation on SQL Server; Passed
<04-25-2014 02:07:09> INFO: Check Machine FQDN: <INFPROSCCMCDB.usersad.everis.int>.
<04-25-2014 02:07:09> INFO: getaddrinfo returned success.
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
Validate FQDN of SQL Server Computer; Passed
<04-25-2014 02:07:09> INFO:CheckSupportedFQDNFormat <INFPROSCCMCDB.usersad.everis.int>
<04-25-2014 02:07:09> INFO: NetBIOS <INFPROSCCMCDB>
<04-25-2014 02:07:09> INFPROSCCMCDB.usersad.everis.int;
Primary FQDN; Passed
<04-25-2014 02:07:09> <<<RuleCategory: Site Upgrade Requirements>>>
<04-25-2014 02:07:09> <<<CategoryDesc: Checking if the target ConfigMgr site is ready to upgrade...>>>
<04-25-2014 02:07:09> <<<RuleCategory: Database Upgrade Requirements>>>
<04-25-2014 02:07:09> <<<CategoryDesc: Checking the target ConfigMgr database is ready to upgrade...>>>
<04-25-2014 02:07:09> ===== INFO: Prerequisite Type & Server: SDK:INFPROSCCMCMS.usersad.everis.int
=====
<04-25-2014 02:07:09> <<<RuleCategory: Access Permissions>>>
<04-25-2014 02:07:09> <<<CategoryDesc: Checking access permissions...>>>
<04-25-2014 02:07:09> INFO: The rule 'Administrative rights on site system' has been run on server 'INFPROSCCMCMS.usersad.everis.int',
skipped.
<04-25-2014 02:07:09> <<<RuleCategory: System Requirements>>>
<04-25-2014 02:07:09> <<<CategoryDesc: Checking system requirements for ConfigMgr...>>>
<04-25-2014 02:07:09> INFO: The rule 'Unsupported site server operating system version for Setup' has
been run on server 'INFPROSCCMCMS.usersad.everis.int', skipped.
<04-25-2014 02:07:09> INFO: The rule 'Domain membership' has been run on server 'INFPROSCCMCMS.usersad.everis.int',
skipped.
<04-25-2014 02:07:09> INFO: Windows Cluster not found on INFPROSCCMCMS.usersad.everis.int.
<04-25-2014 02:07:10> INFPROSCCMCMS.usersad.everis.int;
Windows Failover Cluster; Passed
<04-25-2014 02:07:10> INFO: The rule 'Pending system restart' has been run on server 'INFPROSCCMCMS.usersad.everis.int',
skipped.
<04-25-2014 02:07:10> <<<RuleCategory: Dependent Components>>>
<04-25-2014 02:07:10> <<<CategoryDesc: Checking dependent components for ConfigMgr...>>>
<04-25-2014 02:07:10> INFPROSCCMCMS.usersad.everis.int;
Windows Deployment Tools installed; Passed
<04-25-2014 02:07:10> INFO: CheckAdkWinPeInstalled on INFPROSCCMCMS.usersad.everis.int.
<04-25-2014 02:07:10> INFPROSCCMCMS.usersad.everis.int; Windows Preinstallation Environment
installed; Passed
<04-25-2014 02:07:10> INFPROSCCMCMS.usersad.everis.int;
SMS Provider machine has same domain as site server; Passed
<04-25-2014 02:07:10> <<<RuleCategory: Site Upgrade Requirements>>>
<04-25-2014 02:07:10> <<<CategoryDesc: Checking if the target ConfigMgr site is ready to upgrade...>>>
<04-25-2014 02:07:10> <<<RuleCategory: Database Upgrade Requirements>>>
<04-25-2014 02:07:10> <<<CategoryDesc: Checking the target ConfigMgr database is ready to upgrade...>>>
<04-25-2014 02:07:10> ***************************************************
<04-25-2014 02:07:10> ******* Prerequisite checking is completed. *******
<04-25-2014 02:07:10> ******************************************<04-25-2014 02:07:10> INFO: Updating
Prerequisite checking result into the registry
<04-25-2014 02:07:10> INFO: Connecting to INFPROSCCMCMS.usersad.everis.int registry
<04-25-2014 02:07:10> INFO: Setting registry values
If you wonder whether it might be related to this error:
-2014 02:07:00> INFO: Detected current installed build version [7711] for sitecode [BRA]. For Upgrade, minimum supported installed build version is [7804].
I confirm that this one site is a secondary one that's attached to a primary site and this log is from the CAS server, I managed to tall it and delete it from that site, but still appears listed
on the CAS management console, any idea how to force the removal of a secondary site that's attached to a primary from the CAS site when it has been removed already from said primary?
I've already tried the
Preinst /DELSITE XXX command but it only works when the site to remove it's attached to the local site and certainly not from a CAS
Finally, the version, build number and everything is correct, no idea what could be the problem, does anybody know a way to bypass this or force the re-evaluation of this rules, I've got
the impression that it's being cached somehow.
Any help would be highly appreciated,
Thank you.
Marcelo Estrada MCP-MCTS-MCITP-MCSA-MCSEHello again everybody,
I've finally managed to fix this up, in the end I had to delete those entries manually from the database as Garry suggested. After this was done the upgrade has gone through as expected with no further ado and has finalized already, now moving on to the
primary sites.
If anybody out there is facing the same issue, what I did was to delete those "stubborn" records executing the following statements over the CAS database:
DELETE
FROMServerDataWHERESiteCode='XXX'
DELETE
FROMSC_SiteDefinitionWHERESiteCode='XXX'
And this is pretty much about it. I'd recommend to take a proper backup first though as best practice.
Thank you all anyways for your answers and comments,
Marcelo Estrada MCP-MCTS-MCITP-MCSA-MCSE -
Error Message: "This upgrade path is not supported"
Scenario
During the process of upgrade to Windows 10 Technical Preview, we may encounter the error “This upgrade path is not supported. Please close Setup and re-launch from the root of the media or go back and pick a different installation
choice.” in the Compatibility report.
Analysis
Step 1: Perform the scenario 1: the upgrade installation fails.
Reproduce this error following the steps below:
Download the Windows 10 Technical Preview ISO installation file.
Extract the ISO installation file to C:\New folder, and now the location of the installation file is
C:\New folder\9841.0.140912-1613.FBL_RELEASE_CLIENTENTERPRISE_VOL_X64FRE_EN-US\.
Click setup.exe from the installation file, and then click
Install now.
Setup is starting, and then get two options Upgrade and
Custom which is the classic setup wizard which we can see during booting from DVD.
Click Upgrade to run upgrade installation, however, the error occurs.
It seems that it is impossible to perform upgrade installation to Windows 10 Technical Preview, although it is fine to click
Custom to perform clean installation which cannot keep the personal setting and applications.
However, what we want is upgrade installation, not clean installation.
Step 2: Perform the scenario 2: the upgrade installation works fine.
If extract the ISO installation to C:\New in the above step2, click the
setup.exe from the installation file C:\New\9841.0.140912-1613.FBL_RELEASE_CLIENTENTERPRISE_VOL_X64FRE_EN-US\, the upgrade installation would work fine, which is as shown the following two figures:
Step 3: Check the setupact.log
file which contains information about setup actions during the installation of the two scenarios.
Scenario 1: Check the setupact.log file of the scenario 1. The detailed information is shown as below:
2014-10-14 19:03:40, Info UI Determining whether we should run ConX or legacy setup
2014-10-14 19:03:42, Info UI Will launch ConX setup experience
2014-10-14 19:03:42, Info UI Launching ConX setup experience
2014-10-14 19:03:42, Info UI Launching C:\New folder\9841.0.140912-1613.FBL_RELEASE_CLIENTENTERPRISE_VOL_X64FRE_EN-US\Sources\SetupPrep.exe
2014-10-14 19:03:44, Info UI Unknown command line for ConX setup experience. Launching legacy setup experience.
2014-10-14 19:03:44, Info UI Determining if we are in WDS/Unattend mode
2014-10-14 19:03:44, Info UI No need to hide autorun
2014-10-14 19:03:44, Info [0x0a000a] UI Autorun:Autorun core successfully initialized!!!
2014-10-14 19:03:44, Info [0x0a000b] UI Autorun:Autorun UI successfully initialized!!!
2014-10-14 19:03:44, Info UI AppWindow has layout style 0
2014-10-14 19:03:45, Info UI NavWindow has layout style 0
2014-10-14 19:03:45, Info [0x0a011c] UI WizardDialogPost::SetActive
2014-10-14 19:04:57, Info [0x0a018e] UI Passing command line parameter ("C:\New folder\9841.0.140912-1613.FBL_RELEASE_CLIENTENTERPRISE_VOL_X64FRE_EN-US\Sources\setup.exe /HideWelcome /uilanguage:en-US /targetlanguage:en-US") to IBS.
Scenario 2: Check the setupact.log file of the scenario 2. The detailed information is shown as below:
2014-10-14 19:08:04, Info UI Determining whether we should run ConX or legacy setup
2014-10-14 19:08:05, Info UI Will launch ConX setup experience
2014-10-14 19:08:05, Info UI Launching ConX setup experience
2014-10-14 19:08:05, Info UI Launching C:\New\9841.0.140912-1613.FBL_RELEASE_CLIENTENTERPRISE_VOL_X64FRE_EN-US\Sources\SetupPrep.exe
According to the two logs, we can get the following points:
In scenario 1, it would invoke the SetupPrep.exe in the source folder directly to perform an installation preparation. However, it failed to recognize the path
C:\New folder\9841.0.140912-1613.FBL_RELEASE_CLIENTENTERPRISE_VOL_X64FRE_EN-US\Sources\SetupPrep.exe. Then it would launch legacy setup.
In the scenario 2, Windows setup would be redirected to the ConX setup to perform upgrade installation automatically.
So, what is the difference of the scenario 1 and 2 to bring the different results of upgrade installation?
Workaround
Based on lots of testing, we find that if there is no space in the extracting location of the ISO installation
file, the upgrade installation would work fine.
What’s more, we can get the meaning of the two setup models in the setupact.log:
Legacy setup: it is same with setup from DVD boot.
ConX setup: it would check the compatibility and language UI for upgrade preparation, then perform migration and upgrade directly.
Additional Resource
From the release of Windows 10 Technical Preview, many users have installed and tested Windows 10 Technical Preview, we still hope more and more users would download and install Windows 10 Technical Preview for test, and provide
us your feedback.
Download Windows Technical Preview
http://windows.microsoft.com/en-us/windows/preview-iso
Download Windows Technical Preview for Enterprise
http://www.microsoft.com/en-us/evalcenter/evaluate-windows-technical-preview-for-enterprise
Please click to vote if the post helps you. This can be beneficial to other community members reading the thread.Hello,
I would guess that existence of a space in the folder name is what the issue is. Try removing the space from the folder name and see if works. New_Folder for example
Thanks, Darrell Gorter [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. -
Migrating from CUCM 8.6 to CUCM 10.0 - Do I have to upgrade presence as well?
Hello Raees,
I've got a question regarding the Migration from CUCM 8.6 to 1.0, I went through the below "Ask the Expert" article.
https://supportforums.cisco.com/discussion/12103966/ask-expert-cisco-unified-communications-manager-cucm-version-100
My question is, the CUCM 10.0 upgrade mentions the following on page 22
"Refresh upgrade of Unified Communications Manager nodes only
Complete the high-level tasks listed in this section when you want to perform a refresh upgrade of only the
Unified Communications Manager nodes in your network. When you upgrade Unified Communications
Manager nodes without upgrading IM and Presence nodes, ensure that the installed version of the IM and
Presence Service is compatible with the new version of the Unified Communications Manager software."
I would only like to Upgrade the CUCM nodes but the client is using Presence 8.6 as well, would I have to upgrade Presence 8.6 to something else as well or can I just upgrade to CUCM 10.0 and the presence 8.6 would work with it, if I have to upgrade Presence as well then what version of Presence would I have to upgrade to and for the "Refresh Upgrade for Presence" can you mention the SKU that I got to get off the Product Upgrade Tool.
Since it's going to be a Refresh Upgrade for CUCM from 8.6 to 10.0 can you as well provide me with the SKU for the upgrade that I got to purchase, I can see two of them as follows:
UCM-10.X-SW-K9-XU=
CUCM Software Version 10.X for PUT Only, Export Unrestricted
UCM-10.X-SW-K9=
CUCM Software Version 10.X for PUT Only
Thanks
AamerThank you for the reply Chris,
I have a few more questions with regards to what you mentioned in your reply, I'd be glad if you could clarify:
I have not dealt with IMP before...
1) is it like a plugin that runs on CUCM instead of a full fledged server or is it a stand alone server like CUPS (just renamed/rebranded).... I have till date been dealing with CUPS as a stand alone server that integrates with CUCM via the CUCM -> System-> Application Server Option.
2) If it's a plug-in then how would the upgrade be done from the CUPS Stand Alone to this IMP that runs within the CUCM Server or would it be a fresh installation or some activation of services within CUCM... and if it's a stand alone server then what Upgrade Image do I need to upgrade CUPS 8.6.4 to IMP 10.0 or 10.5.
I'm sorry but the upgrade path for CUPS 8.6.4 to IMP 10.0/10.5 is not clear for me, could you help me understand the migration for CUPS 8.6.4 to IMP 10.0/10.5..... could you as well advise any documentation that shows detailed steps for the upgrade from CUPS 8.6.4 to IMP 10.0/10.5... the CUCM upgrade is clear to me from the Upgrade Guide.
Thank you
Aamer -
Windows 8.1, Update 1 upgrade path
Hi, if there is anyone of any influence who might read this, please, please, for you own sakes make an upgrade path directly from Windows 8.0 --> Windows 8.1, Update 1
I cannot upgrade from W8.0 --> 8.1.
I cannot upgrade due the the following error. But I believe it is a silly error and can be overcome as some have managed:
https://answers.yahoo.com/question/index?qid=20131018074442AAswJqp
http://answers.microsoft.com/en-us/windows/forum/windows8_1-windows_install/windows-81-install-unable-to-create-ramdisk/887b5adc-86ce-4c37-9c58-72eca5f712d4?page=8&tm=1396807793681
I even had a MS 3rd line Andswer Desk (ref:1233447567.) guy who was remote controlling my machine trying clean boot give up after saying that if my
MB manufacturer wont support drivers past Vista then there is nothing they "should" do... But Vista is EoS but not extended support as XP is, that ends 2017:
http://windows.microsoft.com/en-gb/windows/lifecycle
This is an issue I'm having with my personal PC but I also work in IT infrastructure and I think this needs to be sorted. This is going to become a BIG issue for many other people who have Vista/XP-grade systems with the requirements for 8.1.1 who will try
to upgrade.
Please can someone help?
System: Q6600, MB: XFX Nvidia Nforce 680i LT, 8GB RAMHi,
Windows 8.1 do have have higher requirements for hardware, If your computer hardeware device was too old, you may encounter some problem during install or using Windows 8.1.
Roger Lu
TechNet Community Support -
Merom / Conroe upgrade path for Intel iMac?
Has anything been released about a processor upgrade path (if possible) to take the Early 2006 IiMacs from the Yonah CPU family to Merom or Conroe?
I'm still steamed to be stuck with a 32-bit CPU (even though it is a good one, funny how that fact is still judiciously left out of all promotional materials) and wondered if I will be left high and dry in 2-3 months when the 64-bit Core 2 Duo chips ship.
It would be nice if there were an upgrade path to bring the early adopter faithful into the 64-bit realm. Anyone heard a mighty rumblin' ?People have successfully removed the CPU and replaced it. And, the new chips are supposed to be compatible with any Yonah based system.
So, while there is no official upgrade path, it should not be a problem installing a new CPU in the machine later.
Obviously, the heat of the new chips will be a consideration. They may be hotter, they may not be.
And, it will obviously void your warranty.
But, it should be possible. -
Hi,
I have to upgrade Oracle 8.1.6 to Oracle 8.1.7.4. In the Oracle8i Migration Release 3 (8.1.7) PDF documentation, I don't find a upgrade path. So I think I can directly uprade to 8.1.7.4. But somebody told me that I have first upgrade to 8.1.7.0?
Is there anybody with experince in this topic and can help me?
OliverYou have to first upgrade from 8.1.6 to 8.1.7.0 and then apply the 8.1.7.4 patch. 8.1.7.4 is not the full blown database software, it's an upgrade.
The readme for 8.1.7.4 states:
This is not a complete software distribution and you must install it over an existing 8.1.7 Oracle Server installation. -
Is there an upgrade path from Final Cut Studio 3.0 to Final Cut Pro X?
Is there an upgrade path from Final Cut Studio 3.0 to Final Cut Pro X ?
The price of FCPX pretty much is the cost of the upgrade of FCPStudio, but a much better value (at least so far -- every update has been free.) However, it's only the single app so you might feel like you're not getting as much for your money. Don't be fooled. Most of Color and Soundtrack Pro are built into FCPX. FCPX will conform video automatically so Cinema Tools aren't really needed anymore. The Motion engine is part of FCPX, although I do recommend buying Motion 5 (an extra 50 bucks.) (Motion 4 seems to have died in Yosemite - you can't even launch it.)
I "upgraded" from Final Cut Studio 3... it took me about a week to decide to pack up all the old software for good. YMMV. However, if you use DVD Studio Pro... hang on to that. -
We currently have two Nexus 7010 with 5.0(2a) as system images.
We would need to know the correct upgrade path to 6.1(1). On the release notes it reads the path is from 4.2(8), 5.0(5) or 5.1(6) to 5.2(5) then to 6.1(1).
Also if ISSU is possible or, because we may need to upgrade EPLD, if there is no upgrade path to do a non-disruptive upgrade.You probably need to dig a little deeper to get a definitive answer (sup1 or 2, type of cards, etc..) but here is a diagram in the release notes for 6.1 found here:
http://www.cisco.com/en/US/docs/switches/datacenter/sw/6_x/nx-os/release/notes/61_nx-os_release_note.html
If this posts answers your question or is helpful, please consider rating it and/or marking as answered. -
Upgrade path from CCP 9.3R2 to 9.3.2
Hi Team,
Can someone help on the process involved in upgrading a CCP9.3 R2 environment to 9.3.2.
Is the upgrade faily straight forward or do we have to do some customizations to make this happen??
I have a CCP 9.3R2 and CPO 2.2 in a DEV system, have lot of custom content in this environment.
I am upgrading CPO 2.2 to CPO 2.3 engine but not importing the content because I have custom content built on 2.2.
I am liking to know the process doing an upgrade for CCP
- is the inplace upgrade of CCP 9.3R2 to 9.3.2 valid???
OR
- building new CCP 9.3.2 and export / import content from 9.3 R2 to 9.3.2 valid??
Thanks
SatishCCP upgrade should be straight forward. Refer to the CCP doc for upgrade paths and instructions. You would have to test the content you built in 9.3 R2 as I do not know all the inner parts difference in the two versions.
-
Upgrade path from ODI 10.1.3.5
Hello Friends,
We are using ODI 10.1.3.5. Like to get some recommendations on upgrade path from 10.1.3.5.
I read that we need to first upgrade to 10.1.3.6.x before considering upgrade to 11G release.
I guess, this might be in consideration to upgrade with minimal change with patch upgrade to 10.1.3.6.x than upgrading to big change 11G release.
If we have to upgrade to one safe step with not of a big impact/change to users and projects...what release upgrade-to is ideal? 10.1.3.6.x?
Appreciate your response!! Thanks.Thanks for the information. If we have to upgrade to a latest release 11G it looks we can from 10.1.3.5, any suggestions we should consider 11.1.1.5 or 11.1.1.3? Not sure if these release are in sync with target KM's like Essbase & Planning on EPM front we are on 11.1.1.3
-
Upgrade Path for migrating Essbase 7.1 to Essbase 11.1.2.1??
Can any one tell me the upgrade path (and related documents) for migrating Essbase 7.1 to Essbase 11.1.2.1??
Thanks Nathan for your response.
Will the below Essbase Upgrade steps work (From version 7.1 to Version 11.1.2.1 directly)?
1. Install Essbase 11.1.2.1 in one server (new) and Shared Services in another server (new). Both the new servers with Win 2008 OS.
2.Login to EAS console in the new server. Open the outline version 7.1 and then migrate to version 11.1.2.1.
3. Copy the artifacts (such as Calc Scripts and Rule Files etc.) from the Old Essbase directory (Version 7.1) to the new Essbase directory (Version 11.1.2.1).
4. Extract data from the old system and import into the new system.
5. Export Essbase security from old system and import to the shared services of the new system. This might requires some manual interventions.
Or, do I have to upgarde from version 7.1 to 11.1.1.3 and then from 11.1.1.3 to 11.1.2.1?
Maybe you are looking for
-
Mac suddenly can't connect to internet (but sees rest of network ok)
for some very odd reason one of our macs now refuses to see the internet. all the macs are hooked up to a gigabit switch and then to our dsl line via a sisco firewall. the problem mac can see every other mac on the network and connect successfully to
-
Some applications fail to open
Some of my apps no longer open. They used to. Over the wekend I shut down the computer. Yesterday the problems began. The following apps all exhibit the same behavior: Appleworks, Quicken 2007, EyeTV. And that behavior is... - no matter how I try to
-
RollBack Transaction using UDO
Hi I want to perform some validation on MY UDO form. But problem is if i entered some wrong value into our form then what happen, it shows the alert and saved data also. <b>Is it possible to stop this transaction</b> , if yes how???. Plz suggest
-
When I open a new folder and the same again, it shows 2 different folders in 2 different windows. Id like to see only 1 folder, previous folder would be replaced with the new folder. Im awared that there is an option to choose either you want the fol
-
Workflow email for Purchase Requisition Approval
We have a requirement of sending email to the approvers for approving purchase requisition. Alongwith the email sent out to the approvers (to their Outlook/ Lotus Notes Inbox), we will also like to show the content of the line items of the purchase r