Do i need to register my IP Address?

I need to setup my Solution Manager to download support packages and OSS Note Corrections.
For this do i need to register my IP Address with SAP or i just need to go through a few configuration steps.
Actually i am little bit confused about this, i have gone through the initial and basic configuration steps(SOLMAN_SETUP) but i was unable to download SAP Note Correction in step 2 of Basic Configuration.
Please note: SAPOSS RFC is not working
Please Advise,
Thanks

Hi,
You need to setup SAP Router, in order to do so you have to register you sap router hostname and public ip address with sap. Once you do this you will get a distinguish name, using which you have create certificate and setup sap router.
In order to register your credentials create a message under XX-SER-NET-NEW
Only when your sap router is up and running SAPOSS rfc will connect to sap server.
Regards,
SBK

Similar Messages

  • HT204380 Can you use one AppleID/email for FaceTime, to receive an incoming call on both iPad and iPhone so as to answer which ever one is closer?  Or do I need to register another email for my iPad to work with FaceTime?

    Any thoughts?

    You need to register mother email address. See here http://ipad.about.com/od/iPad_Guide/ss/How-To-Use-FaceTime-On-The-iPad_2.htm
    See this thread for further Help - https://discussions.apple.com/message/18530214?ac_cid=tw123456#18530214

  • My MacBook was stolen and I need to know the MAC address

    An emergency question to Apple support. My MacBook was stolen and I need to know the MAC address of its network card. I have a receipt with the serial number of my MacBook. Can you assist?
    My serial: W8***66D
    Thank you
    p.s Any ideas how I can find it?

    Report the theft to your local authorities.
    Apple has no means of tracking thefts, as thieves themselves may claim the machine is theres just by looking up the information on the computer, and unless you registered the machine, it is really their word against yours, unless you also have receipt or other information that they can track to your receipt against your serial number.
    Your homeowners insurance may be able to recoup the cost.
    In the future, consider getting Lapcop, or Lojack for notebooks.
    Good luck!

  • Have 2 registered e-mail addresses, can't read a document or get reader to recognize my id.

    Why won't adobe reader let me log in and read my document using one of my registered e-mail addresses?

    Hi jhenrik,
    You don't need to be logged in to view PDF files in Adobe Reader, so there may be another issue here. What happens when you try to open a document? Do you get an error message?
    As for your username and password, you may want to reset your passwords to make sure that the right password is associated with each email address. (Are you able to log in to www.adobe.com with either email address?).
    Please try resetting your passwords, and then get in touch with us again if that doesn't work.
    Best,
    Sara

  • Do I need to register after purchase of lenovo s860

    Hi ,
        Do I need to register explicity after purchased of lenovo s860 through online?.
    If I want to check the product is origninal or not?
    If I want to increase the warrently what should i have to do?
    Please let us know answers for the above doubts.
    Regards,
    Harish.

    Hi,
    You need to setup SAP Router, in order to do so you have to register you sap router hostname and public ip address with sap. Once you do this you will get a distinguish name, using which you have create certificate and setup sap router.
    In order to register your credentials create a message under XX-SER-NET-NEW
    Only when your sap router is up and running SAPOSS rfc will connect to sap server.
    Regards,
    SBK

  • I recently got a new laptop and I cant get my itunes songs to play. It says I need to register my computer. How do I do this, I obviously not very good at comouters

    I recently got a laptop and I am unable to play my itunes songs on it. It says I need to register tha device. I am unsure on how to do this any help would be appreciated. Also note that I am a beginner and dont have a clue what I am doing. Thank You

    Hi valierie,
    To Authorize your Windows laptop:
    1.     Open iTunes and sign on with your Apple/iTunes ID
    2.     Press CTL+B to display the top menu
    3.     Click on Store in that Menu
    4.     In the dropdown, you should see "Authorize This Computer"
    5.     Click on that to authorize the computer to your iTunes ID
    Cheers,
    GB

  • Updated my AppleID account info.  Under password security shows an email address to be used to receive email with new password settings.  I need to update that email address, how do I do that?  Thanks!

    Updated my AppleID account info.  Under password security shows an email address to be used to receive email with new password settings.  I need to update that email address, how do I do that?  Thanks!

    Thanks for the help Niel.  I couldn't change the rescue email address (an address that no longer exists and is therefore useless) until I could correctly answer the security questions.  After numerous guesses, finally got them right.  Was then presented with the option to change the rescue email address. Guess the only other option was to have Apple Support make the change or reset my account info.  Have made note of the correct answers so this won't happen again.   Thanks for the fast response!!

  • I try to open Acrobat I get a message that I need to register the product. I click on register and after about a minute, I'm told that I don't have an internet connection. My internet connection is working fine. In fact I registered Acrobat Pro XI using m

    I try to open Acrobat I get a message that I need to register the product. I click on register and after about a minute, I'm told that I don't have an internet connection. My internet connection is working fine. In fact I registered Acrobat Pro XI using my account, but the program itself will not recognize it or allow me to use the software. What do I do?

    If you already registered, then there is no point to trying to do so again. Simply dismiss the dialog.
    Mylenium

  • HT4623 i have installed the beta version of 6.1 a month ago and now i cannot open my iphone 5 it needs regestration and when i try to register it says that it couldnt complete and i need to register in the developer what can i do now to reopen my device?

    I have installed the beta version of 6.1 a month ago and now i cannot open my iphone 5 it needs regestration and when i try to register it says that it couldnt complete and i need to register in the developer what can i do now to reopen my device?

    Probably wasn't a good idea to install beta software on a device when you're not a developer.
    Apple clearly states that beta software is not to be installed on production devices.
    Not really much you can do except wait for iOS 6.1 to be officially released and then install it.

  • New CS6 on disk for Mac will not take my valid serial number; do I need to register the product before it will accept serial number and load on my Mac Book Pro?

    New CS6 on disk for Mac will not take my valid serial number; do I need to register the product before it will accept serial number and load on my Mac Book Pro?

    Hi Erwin,
    Please go through the below forum link and check.
    https://forums.adobe.com/thread/1079210
    Regards,
    Anand

  • Icloud still shows my old email address when I try to enter, asking me for a password I no longer have. I need to change my email address and password in ICLOUD but I can't find a way to do it. Any ideas? Thanks.

    icloud still shows my old email address when I try to enter, asking me for a password I no longer have. I need to change my email address and password in ICLOUD but I can't find a way to do it. Any ideas? Thanks.

    Logout (System Preferences>iCloud) then login with the new address and password.

  • Ref:iphone 3G.I was visiting the US last week.One day my iphone battery completely drained overnight.I re-charged it but ever since it has either come up with a message saying it's registering, or that I need to register it.It was registered years ago.

    Ref: iphone 3G. I was visiting the US last week.  My iphone battery completely drained overnight. I re-charged it but ever since it has either come up with a message saying it's registering or saying I need to register it.  I'm concerned that if I re-register it on itunes I'll lose all my data.  I originally registered it a couple of years or so back, when it was new.  Any advice much appreciated.

    Thank you for quick reply.  The data is still there - every so often when I switch it on, it comes up with the main icon screen, rather than the emegency calls only screen (which it does most of the time), and I can get to my contacts, photos, and so on, but it won't connect to any mobile/cell network provider, including my network here in the UK - O2.

  • Do I need to register a domain name?

    Hi,
    I'm new to iWeb and have a simple question. Do I need to register my website's name or do I just type it in during the "Publish" stage?
    Thanks,
    Andrew

    You don't need to register your site name. If you want a domain name like www.mydomainname.com, then you'll have to purchase it and forward it to your site wherever it may be hosted. Where are you publishing to? If you're publishing to MobileMe there's nothing to do in iWeb but click use the File->Publish Entire Site or Publish Site Changes menu option.
    If you're publishing to a 3rd party hosting service you will need to put in the relevant site and server information for that host.
    OT

  • Do I need to create loopback IP address on servers when using LD?

    Beside ASLB mode, do I need to create loopback IP address for the servers when using Local Director?
    Understand LD does not use NAT for IP address, so the server may drop the packet when it sees the packet's destination is not for its own IP.
    And how to set the loopback IP on Windows servers? I can only create the secondary IP under the ethernet NIC configuration, and this always cause the two web servers to complain about duplicated IP address.

    The case of the loopbacks depends on whether you run LDIR in dispatched mode or directed mode.
    Directed mode is a form of NAT where the LDIR changes the destination IP address in the incoming packet to that of the real server chosen.
    Dispatched mode is sort of like 'Layer 2 NAT' or 'MAC NAT', because the LDIR changes the destination MAC address but not the destination IP address. For the server to actually pick up a packet adressed to an IP address not configured on the ingress interface, it will need to have this address configured somewhere else, and this is where the loopback adapter comes into play.
    It is true that with ASLB, you need to run dispatched mode. This is due to how the rewrite is implemented on the C6K (which is needed for ASLB).
    Regarding the Windows configuration, you need to install the loopback adapter. How this is done depends on the Windows version, but basically you need to install the driver manually, as if you had added a physical adapter to the machine and were to manually install a driver. You'll find the loopback adapter under the 'hardware' manufacturer Microsoft in the Add Hardware configuration dialog. When the new 'hardware' has been installed, you can configure an IP address on it like any other NIC.
    So to answer your question: No you do not *need* to use loopbacks when using LDIR, but this depends on the LDIR configuration.
    HTH,
    -A

  • Why do we need to Register a class ?

    When the class is already present in jar file then still why do we need to load the class and use it. The jar file is included in the lib and would be available for the environment.
    If any better explanation is provided will be very useful
    Thanking you in advance

    I assume you are talking about JDBC drivers over here. In general, otherwise you do not need to register classes.
    In JDBC, this has to do with how DriverManager works.
    When you load a driver class using the Class.forName(...) block, you are effectively executing the driver's static block.
    The static block has some code in it to register the class with the DriverManager by calling the static method DriverManager.register(Driver d).
    When your client code attempts to connect to a database by passing a JDBC-URL, the DriverManager iterates through the registered drivers and calls acceptsURL() on each of the drivers. The first driver to return a value of true gets to try connecting to the database.

Maybe you are looking for