Do older basestations and express downgrade the speeds of the newer Airport Extreme?

In the past a device on an Airport network running at a slower speed would downgrade the entire wireless network.
I just purchased a New Airport Extreme. I also have an older Airport Extreme (g) and n Airport Express on my network.
My question is, are these devices downgrading my network speeds?

The new AirPort Extreme is dual-band, which means it simultaneously broadcasts a new (n) network and an old (b/g) network. Devices on the old network will not slow down devices on the new one.
http://www.apple.com/airportextreme/features/frequency.html

Similar Messages

√using successfully airport express for internet/ when hooking up new airport extreme light glows green, but does NOT appear in devices seen????airport wifi devices

using sucessfully airport express for internet
when hooking up new airport extreme light glows green, but does NOT appear in devices sesn in 5.6 airport wifi devices
wanting to use extreme at base and express in another part of the house

How is the express getting internet? What modem is it plugged into?
How is the extreme setup? New extreme cannot be setup with 5.6 utility.. you must use latest 6.3. Which also means you cannot setup from computer using less than Lion .. or you must use iOS with latest utility but it has limited configuration cf the computer version.
IPv6 is also needed.. turn on local link.

Speed problems with new Airport Extreme

Hi,
I just bought the latest Airport Extreme, and am using it as my router directly from my internet provider, a hole in the wall, with a normal cable between.
If I hook the cable right to my computer I get between 500-800 Mbit speed, all the time, rock solid, so my internet connection is very good!
Now, when I hook it up to my new AE, it works fine most of the time, or let's say 70% of the time. The other 30% the speed drops down to roughly 20-50 Mbit from the normal 250-400 speed when using the AE. Itäs not only that the speed drops, all my streaming devices stop working. I have three wireless speakers and an Apple TV. Normally it all works fine... but suddenly they all stop working, and that is when the router (AE) drops in speed.
Sometimes I have to plugg the plug on the AE, to restart it, and it works fine agaian, but sometimes ther's nothing to do.
It feels very strange that you one minute can have 400+ Mbit and then sudenly down to 20, and then back again...without doing anything at all in your apartment with your devices. I run on the 7.7.2 firmware...
Any clues?

I've got a similar sounding issue except when it happens to mine, it stays super slow until I reboot the AE. Not just changes some settings and let it update/refresh, I have to power cycle it. My internet connection isn't quite as fast as yours but it still should be a lot faster than what it is when this starts.
I have a 30Mbit connection. After power cycling the AE, it runs fine for several days. Then at some point, it gets extremely slow. Trying to load any web page takes roughly 30-45 seconds sometimes before it really seems like it starts getting a response from the server and starts downloading the page. I've tried a few pings and the requests continually time out for a while and then it will finally pick up and work.
I'm not real sure what to do about it. I'm wondering if the newest firmware upgrade has anything to do with it. I didn't see this issue until after updating to 7.7.2. May be completely unrelated but thats the only thing I can think of that has changed lately.

Brand New Airport Extreme and Motorola Surfboard 5101 Connection Dropping

I'm going to add to the chorus and point out that my brand spanking new Airport Extreme continually loses internet connectivity with my Motorola Surfboard 5101 modem (this is used on a Time Warner connection).
Disconnecting the Airport and connecting directly to the modem via ethernet cable works flawlessly as does using my old Linksys router. With the Airport Extreme it will work for a number of hours and then drop the internet connection. Airport Utility shows the Airport Extreme as having a green light while the internet connection has the amber "disconnected" light, but, as I said, cutting the Airport out of the connection leaves my internet connection stable and flawless so it seems the problem is either the Airport or the combination of the two.
So, is the only solution to replace the cable modem with one that works with the Airport? If so, how do I know what will work and what won't?
Should I return the Airport? Get a completely different 802.11ac capable router (which one)? Perhaps there is some arcae setting buried deep in the bowels of one device or the other that needs setting?

It's ok, I got. You have to put in password "BT" Never had to do that before, but it works....maybe this helps someone else.

I have just purchased and installed a new Airport extreme base station but now the Airport Utility cannot see my old Airport Express. Are their compatibility issues and do I need to purchase a new Express?

I have just purchased and installed a new Airport extreme base station but now the Airport Utility cannot see my old Airport Express. Are their compatibility issues and do I need to purchase a new Express?

When you can, take a look at the old AirPort Express and locate the model number in the faint print on the side of the device.
If you see A1084 or A1088, this is an older Express version that is no longer supported by the current version of AirPort Utility that you are using with the new AirPort Extreme.
If that is the case, your Express is at least 6 years old...probably older...so it is about time to treat yourself to a new version with much faster speeds and more features.

Installed my new Airport extreme and try to link it to airport express but the wifi still very slow

I installed my new Airport extreme today and try to link it to my airport express to expend my wifi coverage to my second floor but the wifi si very slow on second florr not better then without express? what can I do??

Hi Francois
Any wired connection or WiFi network extension (using your AirPort Express) with your second floor will make your network signal stronger but not necessarly faster. If your WiFi signal is so poor that internet connection keeps dropping, it will make a speed difference. Otherwise the only difference you'll notice is that the range of the wireless network has increased.
You say "wifi is very slow on the second floor". Do you mean that the internet is slow? Is it very fast on the first floor?
Try checking your internet connection speed on a laptop on each floor:
speedtest.net
and press "begin test recommended server".
The download speed should approximate your ISP contracted speed. Upload speed will be a fraction of this. Wifi will be slower but unless you have a super-fast internet connection, you probably shouldn't notice it.
Peter

New Airport Extreme and Older Airport Express No Longer Works

I recently bought a new Airport Extreme base station. Now the Airport Express that I've had for a number of years no longer works, flashing amber. It shows up under the Wi-Fi icon in the menu bar, but when I try to follow Apple's instructions for configuring it, I get this message:
"This version of AirPort Utility doesn't support this base station. Use AirPort Utility 5.6 to configure or manage this base station. AirPort Utility 5.6 is available at AirPort Service and Support."
I then tried downloading and installing Airport Utility 5.6 on my MacBook Pro (running OS X 10.7.4) and received this error message: "AirPort Utility can't be installed on this disk. The version of Mac OS X on this volume is not supported."
I then turned to my IPad, which also detected the Airport Express under Wi-Fi Settings but returned a message when I tried to set it up that the Airport Express couldn't be set by this software and re-directed me to the support web site.
While we have an Apple TV unit, I used the Airport Express to stream music directly to our stereo from my MacBook and IPad and Phone and would love to be able to continue to do so. Has anyone found a workaround for this problem, or will I be forced to buy a new Airport Express as well?
Thanks for any help you can offer,
Steve

I then tried downloading and installing Airport Utility 5.6 on my MacBook Pro (running OS X 10.7.4) and received this error message: "AirPort Utility can't be installed on this disk. The version of Mac OS X on this volume is not supported."
I just tried this on my MacBook Pro running 10.7.4 and had no problems downloading and installing AirPort Utility 5.6 for Mac OS X Lion
AirPort Utility 5.6.1 will not install on a Mac running Lion....only Snow Leopard or Leopard.
Can you check again to make sure that you are trying to install 5.6 and not 5.6.1?

I set up time capsule using a wireless 4g modem. it's been five hours and it still is saying making backup disk available (4.97 GB of 18.52 GB). Can I stop the whole thing, get a ethernet cable and start over to increase the speed of the backup?

I set up a new time capsule on a wireless 4g modem. I started the initial backup. It's been five hours and it still says "making backup disk available (4.97 GB of 18.52 GB)." Can I stop the whole thing, connect my computer to the time machine using an ethernet cable and start over to increase the speed of the backup?
Thanks,
David

Bunce wrote:
oh i already did that. Im working on my imac and looking into this on my macbook. Was able to reproduce the issue again by trying to open TM. Locked out the finder again and had to restart. I checked the serial number and it was an early 2009 purchase with no coverage.
If you bought a Mac and got AppleCare with it, within 2 years of buying the TC, the TC is covered, too.
I have to admit that this $500 unit was the first to apparently junk out. The western digital that had my main data on that is my daily external that I store about 2TB of data on is still perfect and the new technology TM appears to already be cashed. Love the computers, not to big of a fan on the externals of the apple TV's. No life expectancy. Neither here nor there.
suggestions before I either get this looked at or scrap the HD on it and move forward.?
Reset the TC. See [Resetting an AirPort Base Station or Time Capsule FAQ|http://support.apple.com/kb/ht3728].
Try a "full reset" of Time Machine, per #A4 in [Time Machine - Troubleshooting|http://web.me.com/pondini/Time_Machine/Troubleshooting.html] (or use the link in *User Tips* at the top of the +Time Machine+ forum).
If all else fails, take it to your local Apple Store or Authorized Repair location, they may be able to determine whether the disk is dead.
If it is, they might replace the TC for you. If not, they won't repair it, but if the electronics are ok, you can replace the HD yourself, if you want to. See http://discussions.apple.com/thread.jspa?threadID=2542983

I have a new Airport Extreme and an old airport express. I am getting an amber light on the new Extreme and a green light on the Express. I have internet no problem but the status light is blinking amber

I have a new Airport Extreme and and old airport express. I am getting an amber status light on the Extreme and a green light on the Express. The Extreme is blinking amber all the time.
I have internet and everything seems to be working.
I have reset and pulled the power cord on both the extreme and the internet block
How do I make it Green?

If things seem to be working OK, but the amber light is flashing......the AirPort Extreme has a message for you. To see what that might be......
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon
Click on the amber dot in the small window
It might be a message that a firmware update is available for your AirPort Extreme.

How can i measure the speed of the fan in sound and vibration signal simulator box

how can i measure the speed of the fan in sound and vibration signal simulator box
provided the values tach out:2 pulses/revolution and maximum speed = 6000rpm

Hi. I tried your suggestion and I could not get it to work well. In
fact it worked better without the running average (which suprised me).
I also played with the number of data points but still could not get it
to work well.
Do you have any other suggestions on how I could sort this problem out?
I
have attached a screen shot of the signal. To recap, I'm trying to
measure the'y' position of the flat regions of the signal. The signal
does not have a constant level, so this 'y' position varies with time
in a non-unform manner.
I am currently differentiating
the signal and selecting the y position when the differential is equal
to zero (within a tolerance band).
In the screenshot, the
signal has been zeroed using the method I have described above.
However, it occasionally has glitches which may be caused when the code
picks up a zero gradient at a peak or valley in the signal.
I therefore need some kind of algorithm that only measures the position of the flat regions.
Many thanks
John
Attachments:
screenshot.gif ‏121 KB

TS1741 Remote isn't recognising my new AirPort Extreme but does pick up an old appleTV and ap express and extreme.anyone know why? It does pick it up from the Music app

Remote isn't recognising my new AirPort Extreme but does pick up an old appleTV and ap express and extreme.Anyone know why? It does pick it up the new AP express from the Music app and plays through a single speaker

Remote isn't recognising my new AirPort Extreme but does pick up an old appleTV and ap express and extreme.Anyone know why? It does pick it up the new AP express from the Music app and plays through a single speaker

Just bought a brand new Airport Extreme and having trouble with it being recognized. I have a Mac version 10.5.8. Is my computer compatible? I have the Airport Express now and it works fine.

Just bought a brand new airport extreme and having trouble with it being recognized. My mac is version 10.5.8. What should I do?

The new AirPort Extreme needs the 6.x version of AirPort Utility, which comes packed in with Lion 10.7.5 or Mountain Lion 10.8.x......or......you can also configure the device using an iPhone or iPad running a recent iOS.
From Apple's Specifications:
Setup and Administration
iPhone, iPad, or iPod touch with iOS 5 or later and AirPort Utility 1.3
Mac with OS X Lion v10.7.5 or later and AirPort Utility 6.3
A few options.....
Borrow another Mac running Lion or Mountain Lion for 10-15 minutes and set it up. The Mac running 10.5.8 will be able to connect to the wireless....but it will not be able to make any changes to the configuration of the Extreme.
Update to Lion or Mountain Lion.....but check first to make sure that your Mac will support the operating system first.
Use....or borrow an iPhone or iPad to set up the Extreme

Proper way to mix new Airport Extreme with Airport Express, wired and wirel

I currently have several macs. Two of them have 1000 airport (macbook pro and macpro), the other 3 have 100 speed.
I have one Airport Express I'm using now. I'd like a faster setup though.
Here's how I've got it wired up now:
1. I go from my cable modem into a 10/100 Linksys wired router
2. A Net gear 10/100/1000 4-port switch is hooked to the router
3. My airport Express is hooked to the switch
4. my 4 other macs then are hard wired with regular ethernet cable to the switch.
So, my wireless is only for the device(s) that need it, and all other macs go through wires to the switch.
Now, I want to buy a new Airport Extreme to increase my wireless speed when copying files and sharing my iTunes library.
Will having the Express on the network make the Extreme jump down to 100 speed? Or, should I buy a new router, a 10/100/1000 router, and just plug the new Extreme right into it, thereby separating it technically from the slower Express/wired stuff?
I guess I won't even need the Express anymore unless I use it for my older macs that don't have the new n speed airport cards, right?
any insight would be helpful, I'd hate to buy stuff I don't need, and vice versa.

Please try taking the readings again using iStumbler's Inspector feature (select Edit > Inspector from iStumbler's menu) to determine the Signal-to-Noise Ratio (SNR) at your iMac for the following two cases:
o Case_#1: Just the AEBSn. (Temporarily unplug the AX for this reading.)
o Case_#2: When the network is configured for WDS.
Within the Inspector, on the Properties tab, note the values for "signal" & "noise" for each of these cases. These values should be negative.
SNR is the signal level (in dBm) minus the noise level (in dBm). For example, a signal level of -53dBm measured near an access point and typical noise level of -90dBm yields a SNR of 37dB, a healthy value for wireless LANs.
SNR Guideline
o 40dB+ SNR = Excellent signal
o 25dB to 40dB SNR = Very good signal
o 15dB to 25dB SNR = Low signal
o 10dB to 15dB SNR = Very low signal
o 5dB to 10dB SNR = No signal
For Case_#1, if the SNR is 20+dB, you may consider not using a WDS as this SNR value would represent decent Wi-Fi performance at your iMac's location from the AEBSn alone. If it's less than 20dB, then the WDS would be required. ... and, if this is the case, you would want to place the AX within the 20+dB range of the AEBSn to make sure it has the strongest signal to repeat.

Hi i am currently editing clips in premiere pro cc but everytime i go to change the speed not the duration of a clip it will not let me select it - also when i go to effect controls it will not let me select time mapping? please help

Hi i am currently editing clips in premiere pro cc but everytime i go to change the speed not the duration of a clip it will not let me select it - also when i go to effect controls it will not let me select time mapping? please help

savannahp
What version of Premiere Elements and on what computer operating system?
Please review the following that I excerpted from an older post here regarding Adobe's PRE_help comments about Hollywood Effect and mention of
Red Noir. Does any of the following apply to any of what is happening to you.
- Whenever I try to add an effect from the Hollywood Looks menu, it brings up a warning that all my previous effects on that clip will be deleted. However it will let me add those same effects *after* applying Hollywood Looks.
This is because of how the Hollywood Looks are designed to be used. Since these are effect presets (multiple effects in combination) that result in a specific "look"; they are best applied in isolation. If any previous effect is applied and we still allow a Hollywood effect to be applied, we will not be able to see what the effect does clearly. For e.g. if you already have a Gaussian Blur effect applied to your clip, and then we allow you to apply the "Red Noir" Hollywood effect, the fact that the "Reds" in the scenes will be highlighted and the others converted to B/W will not be clearly seen since the content is already blurred out. So any previously applied effects was designed to be removed. This holds good even if you apply a Hollywood look "on top of" another one. The previous one will be replaced. Having said that, you can customize the look further by either tweaking an already applied filter or by adding a newer effect on top. That is the reason you can apply an effect on top of the Hollywood Effects and not vice versa.
Please review and consider and then we can proceed from there if necessary.
ATR

How to connect old aiport express to my new Airport Extreme? My Ipad says "base station e5713b cannot be configured" and my AirPort tool on my PC will not permit me to add my new Airport Extreme network (no network names to choose from)

How to connect old aiport express to my new Airport Extreme?
I have a PC running with Win7 and just replaced my Jensen With a brand New Airport Extreme.
I have set up the Airport Extreme to the internet, Iphones and Ipads and it work as it should.
I have downloaded latest Version of Airport tool on my PC. In addition i have downloaded the airport tool for Ipad.
I have reset one of my airport Express and it now shows up both on the Ipad and on the PC airport tool.
My Ipad says "base station e5713b cannot be configured."
I have wired the airport Express to my Ethernet to be able to "see it" on my Airport tool.
My AirPort tool on the PC will not permit me to add the airport Express to my new Airport Extreme network (no network names on the drop-down list to choose from). I wished for an easy set-up, but nothing seems to be plug and play as the Commercial says.. can you please help me?
Sigve

Hi
Thanks for Swift reply.
Yep - I in fact have two A1088 and one A1264
I actually bought the new router because the Jensen
router always lost connection to the Airport Express after some hours or days. I
always needed to restart my Jensen to play music and that was driving my wife
mad. The hope was that the Extreme should fix this. Both A1088 have been set up
to only stream music to two of my stereo amplifiers from my PC’s Itunes library.
Are the A1088 now useless?
The A1264 has been set up to feed internet into a Denon Reciever that needed Ethernet cable.
Please advise
Regards
Sigve

Do older basestations and express downgrade the speeds of the newer Airport Extreme?

Similar Messages

Maybe you are looking for