Does 1900 series router supports voice functon?

                   I have seen that 1921 and 1941 can insert a vwic3 interface card,but i cannot see pvdm on 1921&1941,my question is that how 1921&1941 support voice function(e.g voice termination)?

Hi.
Based on these docs, it does not support voice
http://www.cisco.com/en/US/products/ps10538/prod_series_comparison.html
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6789/ps7290/ps10589/data_sheet_c78-598389.html
VWIC3 cards are not only for voice, that's why you can add them to a 1900 series router.
http://www.cisco.com/en/US/prod/collateral/routers/ps5855/data_sheet_c36-609138.html
HTH
Regards
Carlo
Sent from Cisco Technical Support iPhone App

Similar Messages

  • Does CRM email router support digitally signed emails?

    Hello There,
    I have configured email router in a one of our test environment to check, i am able to trace incoming mails which has digital signed mails get tracked in CRM. 
    Does CRM email router support digitally signed emails? 
    i am not able to trace mails in to CRM,, have you ever faced this ???? kindly suggest i need this to figure this out.
    Thanks,
    Vinay Kumar.
    Vinay Kumar.

    Thanks Vinay, glad you got it working. We were having some issues and its related to the level of rollup and whether certain headers are allowed through exchange or not.
    However MS's answer is that it does not work.
    Confusing eh.
    CHeers
    Stuart
    Stuart

  • Configuring New Interface and NAT on Cisco 1900 Series Router.

    Hello Cisco Team,
    am asking for advise on how to how setup NAT rules and overload on my 2nd interface on my cisco 1900 series router,am not sure where am getting it wrong.
    my router has 2 interface, interface one has IP address 10.5.5.5X and plugs into my ASA firwall and into my switch and works just fine.
    i have just configured my second Interface with a new IP 172.16.0.X- i  want to NAT my new IP address to our public IP address which is 41.77.X.X
    my configuration so far are as follows.
    GigabitEthernet0/0         172.16.0.X      YES manual up                    up - Not working                                                                            
    GigabitEthernet0/1         10.5.5.X      YES NVRAM  up                    up- this works fine
    GigabitEthernet0/0/0       41.77.X.X  YES NVRAM  up                    up   

    Hello Jon,
    Thanks for your feedback, my router configuration are as follows.
     interface GigabitEthernet0/0
     description WL2504
     ip address 172.16.0.2 255.255.254.0
     duplex auto
     speed auto
    interface GigabitEthernet0/1
     description WAN
     ip address 10.55.55.2 255.255.255.252
     ip nat inside
     ip virtual-reassembly in
     duplex auto
     speed auto
    interface GigabitEthernet0/0/0
     description LINK TO CLT INTERNET
     ip address 41.X.X.130 255.255.255.248
     ip nat outside
     ip virtual-reassembly in
     duplex full
     speed 100
     media-type sfp
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    ip nat inside source list 1 interface GigabitEthernet0/0/0 overload
    ip route 0.0.0.0 0.0.0.0 41.X.X.129
    ip route 41.X.X.136 255.255.255.248 10.55.55.1
    ip route 192.168.0.0 255.255.255.0 10.55.55.1
    access-list 1 permit 10.55.55.0 0.0.0.255
    access-list 1 permit 192.168.0.0 0.0.0.255
    access-list 1 permit 192.168.1.0 0.0.0.255
    from the router interface  interface GigabitEthernet0/0- I will connect it to my wireless Controller WL 2504

  • IOs for cisco 1900 series router

    Hi,
    Kindly provide me the IOS version (cisco 1900 router) which can fix the below listed Bugs,
    Cisco IOS TCP Listener Crafted Packets Remote DoS (CSCek37177)
    Cisco Multiple Devices Crafted IP Option Remote Code Execution (CSCeh52410)
    Cisco IOS System Timers Remote Overflow (CSCei61732)
    Cisco IOS Secure Shell Server TACACS+ Multiple DoS (CSCed65778, CSCed65285)
    Cisco IOS IKE XAUTH ISAKMP IPSec SA Establish Authentication Bypass(CSCeg00277)
    Cisco IOS Telnet Service DoS (CSCef46191)
    Cisco IOS H.323 Protocol Implementation Flaws Cisco IOS Malformed IPv4 Packet Remote DoS Cisco SSH2 Server/Client Malformed Packet Remote DoS (CSCdz60229, CSCdy87221, CSCdu75477)
    Cisco IOS SSH Large Packet CPU Consumption DoS (CSCdw33027) Cisco SIP Crafted INVITE Message Handling DoS (CSCdz39284, CSCdz41124) Cisco IOS Data-link Switching (DLSw) Capabilities Exchange Remote DoS (CSCsf28840)
    Cisco IOS AAA RADIUS Long Username Authentication Bypass (CSCee45312)
    Cisco IOS TCLSH AAA Command Authorization Bypass (CSCeh73049)
    Cisco IOS MMP Stack Group Bidding Protocol (SGBP) Crafted UDP Packet Remote DoS (CSCsb11124)
    Cisco IOS IPv6 Packet Processing Arbitrary Code Execution (CSCef68324)
    Cisco IOS Malformed BGP Packet Processing Remote DoS (CSCee67450)
    Cisco IOS Multi Protocol Label Switching (MPLS) Packet Remote DoS (CSCeb56909)
    Cisco IOS IPv6 Packet Processing Remote DoS (CSCed40933)
    Cisco IOS SCCP Control Protocol Malformed Message DoS (CSCee08584)
    Cisco IOS OSPF Packet Handling DoS (CSCec16481) Cisco IOS ARP Table Overwrite DoS (CSCdu81936)
    Regards,
    Bala

    Hi,
    The Current running IOS version is 12.2(4)T7. I tried through bug toolkit. but i couldn't able to consolidate the IOS to fix these bugs.
    Regards,
    A.Bala
    leolaohoo wrote at Tue Jan 25 02:20:52 GMT+05:30 2011:
    >Balakrishnan Appavu,
    >
    >A new message was posted in the Discussion thread "IOs for cisco 1900 series router":
    >
    >https://supportforums.cisco.com/message/3277195#3277195
    >
    >Author : leolaohoo
    >Profile : https://supportforums.cisco.com/people/leolaohoo
    >
    >Message:

  • Does SRP series routers support VRRP?

    Hi,
    can somebody check if SRP routers support VRRP or HSRP? In documentation isn't this capability mentioned. I need make a backup to my main IOS based router.
    Regards, Martin

    Hi,
    the console port indeed does not support RS232 modem control (data set ready/Data Carrier Detect (DSR/DCD), data terminal ready (DTR)). However, you cannot change the settings on the console port. You need to configure your modem to to ignore DTR and assert autoanswer. The associated Hayes-compatible commands are AT&D0 and ATS0=1, respectively.
    Regards,
    Nethelper

  • IPS on 1900 series Router

    This should be a simple question.
    Customer is thinking about the whole IDS/IPS environment.
    He has some 1921 routers.
    Am I correct is saying that If the router has the FL-SEC installed, then all they would need is to purchase the CON-SUSA-1921SEC subscription?
    And if he has a plain router, then he needs to add the FL-SEC and then the CON-SUSA-1921SEC?
    Thanks

    Within the Cisco Virtual Switching System, one chassis is designated as the active virtual switch and the other is designated as the standby virtual switch. It should be noted that there is no requirement that the two members of the Cisco Virtual Switching System use the same chassis type. The members consisting of the Cisco Virtual Switching System can be different chassis with varying slot counts. Additionally, note that no Cisco 7600 Series chassis will be supported after the system is converted to Cisco Virtual Switching System mode. The initial release of the Cisco Virtual Switching System supports only one Supervisor Engine 720-10G VSS per chassis. A subsequent software release will allow for redundant supervisors to exist in a single physical chassis within the VSS.

  • Does mak book pro support voice and vedio chat on yahoo messenger with windows yahoo messenger on the other line?

    dear All,
    i am planing to buy Makboocpro 13. but befor muying the mac i need to make sure that it is support the voice and vedio chat on yahoo messenger with another windows yahoo messenger user.
    that is very importabt to me cause if not i won't but it
    appreciate your feed back
    thanks
    Hamed Nofal
    [email protected]

    Hi Joseph,
    I have 2011 Mac Book Pro 13 and I have Yahoo 3.0.1 Beta version of Messenger. I am not able to chat with my friends, who are using Windows OS. As a matter of fact, I tried to view my cam on yahoo but somehow it says, "permission denied"!!
    Any configuration issue?
    Your help is appreciated.
    Thank you.

  • Does Cisco 857 router support Easy VPN?!!

    Hi,
    I've a Cisco 857 router with a 12.4(6)T IOS.
    I want to configure it to act as an Easy VPN server, to allow my remote clients -using cisco vpn clients- to access the internal resourses behind the router.
    Is it applicable with this router model?!!
    thanks and regards,
    Ala

    Ala, upsolutely, you would probably need advance k9 security image, check at software advisory tools and slect software features for your platform.
    sofware advisory
    http://tools.cisco.com/Support/Fusion/FusionHome.do
    857 Models See table 3 Software feature
    http://www.cisco.com/en/US/prod/collateral/routers/ps380/ps6195/product_data_sheet0900aecd8028a9a9_ps380_Products_Data_Sheet.html
    HTH
    Rgds
    Jorge

  • Does the Cisco 26XX-XM router support E1 CAS signaling

    Does the Cisco 2600-XM series router support E1 CAS signalling for its E1 digital voice port or jst only support E1 R2 signaling.
    Thanks

    Only E1 R2 and E1 PRI.
    Taimoor

  • 1900 series warranty

    Hi,
    Can anyone clarify what does "1 year limited liability warranty" offer. This is with refrence to 1900 series router warranty.
    I checked the Cisco Warranty Q&A (https://www.cisco.com/en/US/prod/warranty_qa_guest.html) page but it does not also mention any thing with refrence to 1 year limited liability warranty.
    Regards
    ijlal

    Per the 1900 Series Data Sheet:
    Warranty Information
    The Cisco 1900 Series Integrated Services Router have a 1 year limited liability warranty.
    By the way this forum is dedicated to the Cisco Small Business routers, not really the best forum for the ISR routers.  The best Support Forum for all Traditional Cisco products is the Cisco Netpro Support Forum (Netpro link at the near the top of this page).
    Best Regards,
    Glenn

  • 3600 series router for VOIP

    i need to know will cisco 3600 series router support 4 to 6 E1 for voice over IP using ISDN or PRI singnaling if 2-Port E1 Multiflex Trunk Voice/WAN Interface Cards (VWICs)is used in three slots provided by 3600 routers

    For Cisco 3600 routers to support VOIP you need to have NM-HDA module to provide DSP support without which VOIP can not be handled on 3600 series routers.Maximum Number of NM-HDAs Allowed in 3640 routrer is 3 and 3660 router is 6.So you can use either 3640 or 3660.

  • Does 1841 router support IPsec vpn?

    Hi,
    how can i check if my router supports IPsec VPN?
    Cisco 1841 Software (C18410IPBASEK9-M), 12.4(11)T
    regards
    kimhoe

    Hi,
    Yes, it does support IPSEC VPN. You can check it from software adviser tool at Cisco site,
    http://www.cisco.com/en/US/partner/support/tsd_most_requested_tools.html
    Regards,
    ~JG
    Please rate helpful posts

  • Does OCMS Support Voice Recognition?

    Hi,
    I am interested in building a voice recognition solution so customers can call in and create their own Service Request in Oracle CRM. I've seen a couple of old articles (2004/05) about Oracle building this capability into their Mobility Server product but can't find any info on the Oracle site.
    Does anyone know if OCMS supports voice recognition? If so, is there any doco on it? Is it hard to do?
    Any help appreciated.
    PL

    PL,
    OCMS in itself is purely a singalling server and does not support media operations such as voice recognition. However, OCMS does work with media servers such as Genesys' VoiceGenie VoiceXML platform, which does perform Speech Recognition with VoiceXML scripts.
    Adam

  • Just like HP servers, does Cisco UCS C-Series Standalone supports Network Fault Tolerance ?

    Just like HP servers, does Cisco UCS C-Series Standalone supports Network Fault Tolerance ? if yes then, where can i find this option
    Windows :- 2k8 R2

    Just like HP servers, does Cisco UCS C-Series Standalone supports Network Fault Tolerance ? if yes then, where can i find this option
    Windows :- 2k8 R2

  • Does the UCS C-Series Servers supports PCI/e card digium T1/E1

    Hello,
    Does the UCS C-Series Servers supports/compatible with PCI/e card digium  TE407P/TE420 T1/E1.?
    The server will be used as Asterisk server.
    Thanks
    Philip

    Hi Philip,
    Compatibility will depend on the server model that you have and whether the digium card is a full length, low profile, or half length pcie card.  Take a look at http://www.cisco.com/en/US/products/ps10493/prod_models_comparison.html#~tab-a for details.  If there are any issues with the card itself once it is installed it will have to go through the 3rd party manufacturer.

Maybe you are looking for