Does ACI support a VXLAN Tunnel between Leaf(Leaves) and VMware-vDS, and MS-vSwtich?

Hi Experts,
I have a quick question about Normalized Forwarding of ACI Fabric.
Does ACI support a VXLAN Tunnel between Leaf(Leaves) and VMware-vDS, and MS-vSwtich? Otherwise any plan to provide that function in the future?
If there is no function and plan How is Normalized Forwarding possible with VXLAN headers that are generated by each Hypervisor? Of course I know it's possible for a VM on ESXi to communicate with another VMs on Hper-V without VXLAN but I just focus on Normalized Forwarding between Multi-Hypervisor.
Or If AVSs are implemented on ESXi and Hyper-V repectively, is it possible to make a VXLAN Tunnel between Leaf(Leaves) and AVSs on ESXi and Hyper-V? And what is a example of that usage?
Thanks in advance.
Paul

Hi Paul,
As I understand, ACI Leaf to the VMware-vDS is still vlan so no tunnel for VXLAN. When we integrate Vcenter with the ACI, We define the vlan range for the traffic from VM-ware-vDS to map EPG to a VMware ESXi port group.
For the MS-vSwitch, As It support OpFlex agent could act as VTEP but not part of the fabric. But I am not sure about this.
As AVS is part of the fabric so It will act as a VTEP (VXLAN Tunnel between Leaf(Leaves) and AVSs)
But what is the benefit are you looking? Traffic normalization is still there because Traffic within the fabric is encapsulated as VXLAN. External VLAN/VXLAN/NVGRE tags are mapped at ingress to an internal VXLAN tag.
Note:the VLAN ID has local significance for the leaf node
Regards,
Anser

Similar Messages

The printing of .pdf file from Project 2013 stops when the file name should be written. Project 2013 crashes. Does someone know what is wrong between Project 2013 and Adobe Acrobat 9?

The printing of .pdf file from Project 2013 stops when the file name should be written. Project 2013 crashes. Does someone know what is wrong between Project 2013 and Adobe Acrobat 9?

The Acrobat 9.x product family passed into "End of Support" mid-year of 2013.
Acrobat 9 support of MS Project via PDFMaker stops with Office 2007.
For Office 2013 support you must use Acrobat XI (11.0.1) or newer.
A good to have reference:
https://helpx.adobe.com/acrobat/kb/compatible-web-browsers-pdfmaker-applications.html
Acrobat Pro and Standard DC are what are currently available for purchase.
Be well...

My host name changes every few days, since Xmas adding a macbook its changed 6 times. Do I need to stop this? Does it cause problems with sharing between the iMac and macbook?

my host name changes every few days, since Xmas adding a macbook its changed 6 times. Do I need to stop this? Does it cause problems with sharing between the iMac and macbook?

There are several possible causes for this problem.
1. Two (or more) computers on the local network have the same Bonjour name, such as "X's-MacBook-Pro.local".
2. You have two simultaneous connections to the same local network: probably Ethernet and Wi-Fi. If applicable, disconnect the Ethernet cable or turn off Wi-Fi.
3. A Mac wakes from sleep due to network traffic. This is due to a bug in OS X that may only affect some models.
4. A device that gets its network address from the router wakes from sleep, and the address it was using before has been assigned to another device.
5. A third-party wireless router has incompatible settings or firmware. In that case, refer to the manufacturer or ISP for support. Restarting the router may help, temporarily.
6. See also this support article.
Rename the computer in the Sharing preference pane.

Is there a way to Move files to the iCloud thus freeing up disk space on my Mac? Or does iCloud only sync (replicate) files between my Mac and the cloud?

Is there a way to Move files to the iCloud thus freeing up disk space on my Mac? Or does iCloud only sync (replicate) files between my Mac and the cloud? I want to free up disk space on my Mac and assumed that the icloud would be a good way to do this, but having 'moved' 70Gb of files to the iCloud drive (I've upgraded to 200Gb storage) my Mac is still nearly full and I've realised that it seems to just Sync files just like dropbox.

So, the big question is did the Apple guys confirm that this is how the new iCloud drive should be working? I'm guessing, from your response, that this is indeed the case. Are they going to fix this anytime soon? I thought that this was a new function of the iCloud drive in Yosemite.
I just want an online storage facility to back up my photo & music collections. I did look at Dropbox as they have a good deal going with their Dropbox Pro, however this is still just a sync service where the Master files reside on your local disk drive - although I have read that there may be a way to work around this. Still not ideal.

How the hell does a person share session data between JSP page and a Servle

1. How the hell does one share session data between a servlet and a JSP page without using a bean but rather using a normal string variable.
2. When using session scope to access a bean the application complains about not finding the bean on the specified scope, however when I use an application scope the save the same bean, the application does find it.
Please help!!!!!!!
SERVLET:
HttpSession session = request.getSession(true);
ServletContext servletContext = session.getServletContext();
customerID = result.getString("CustomerID");
userName = result.getString("UserName");
session.setAttribute("UserName",userName);
session.setAttribute("CustomerID",customerID);
System.out.println("Customer UserName = " + session.getAttribute("UserName"));
response.sendRedirect("/economics/subscriptions/default.jsp");
JSP PAGE:
<?xml version="1.0" encoding="UTF-8"?>
<jsp:root xmlns:jsp=http://java.sun.com/JSP/Page mlns:c="http://java.sun.com/jsp/jstl/core" xmlns:sql="http://java.sun.com/jsp/jstl/sql" version="2.0">
<jsp:directive.page isThreadSafe="true" session="true" contentType="text/xml"/><jsp:output omit-xml-declaration="false"/><jsp:scriptlet>response.addHeader("x-xslt-nocache", "true");</jsp:scriptlet><pml>
<page type="web" search="y">
     <pageName>Commercial Banking</pageName>
     <jsp:directive.include file="/economics/header.inc"/>
     <jsp:directive.include file="/login.inc"/>
     <jsp:directive.include file="/economics/leftMenu.inc"/>
     
     <content>
     <searchSum>Commercial - Main Content</searchSum>
     Value = <c:out value="${request.session.getAttribute("UserName")}"/>
     </content>
     <jsp:directive.include file="/economics/rightNav.inc"/>
     <jsp:directive.include file="/footer.inc"/>
</page></pml></jsp:root>

For a start, just "session" instead of "request.session" would work better. But why did you post this here and not in the JSP forum? Doesn't seem to have anything to do with Java programming.

HT4623 I have an iPad 3.2 and would like to upgrade the IOS to 5 or 6. I'm having difficulty doing so, including using a cable between my laptop and my iPad. What should I do?

I have an iPad 3 and have attempted, without success, to upgrade to iOS to 5 or 6. I've tried it wirelessly, without success, and cabled it to my laptop, also without success. What am I doing wrong?

The option to update without the computer (Over the air) was made available with iOS 5. If your iDevice is using a version of iOS lower than 5, you will need to use iTunes on your syncing computer to perform the upgrade. Use the Apple link below as a guide for the upgrade.
http://support.apple.com/kb/HT4972
Also read the instructions from the section entitled "Update your device using iTunes" at the link below.
http://support.apple.com/kb/HT4623
Information regarding transferring purchases from your iDevice to iTunes on your syncing computer can be found at the link below.
http://support.apple.com/kb/ht1848

Does itunes support intel x3100 graphics for watch video and tv shows in itunes: not working

Hi I have a asus p5k-vm motherboard with intel 3100 onboad graphics accelerator. I had a gtx 570 video card install and was using itunes
to watch video and tv shows. I sold my gtx 570 and I am using intel x3100 onboard graphics accelerator as my video card. Everything works
fine until I try to watch video or tv shows in itunes. When it tries to start, the screen starts and then right awat it stop and shuts down becuse of some error. I don't know what the problem is.
Please help.

Since updating to 5.0 numerous people have had an issue with optical out. . Try Restart your ATV & computer. Also cycle the power on the ATV and TV (unplug it for 30sec). You should also submit a bug report directly to Apple since they DO NOT read these forums
https://www.apple.com/feedback/appletv.html

Why does Apple support not have the manual for iPad and iOS5 available? The manual on the site has none of the new features.

Has anyone else noticed that the manual has none of the new features, for example iCloud in it? The iPhone iOS5 manual is correct.

http://manuals.info.apple.com/en_US/ipad_user_guide.pdf

L2 tunnel between me3600x and 3925

Hello,
We are currently trying to configure a l2tunnel between a ME3600X (running 15.3(3)S3 with the AdvancedMetroIPAccess licence) and a 3925 (running 15.0(1)M2 with the datak9 licence).
We are part of a CsC architecture, playing the role of the customer carrier, using BGP for label distribution between the Backbone carrier and the Customer carrier.
Our architecture is quite flat as the CE and PE roles are on the same routers.
we have the view on the following architecture and can configure the R1, RCV1, RCV2 and R2 routers :
R1 --- RCV1---(Backbone Carrier)---RCV2--- R2
We have 3 sites A,B and C but only 2 dark fibers to connect them.
We are using the CsC to build a L2 tunnel and close the triangle :
   A-ME=tun=3925-B
     df          df
               C
For year were using a 2911 and a 3900 to build the tunnel and it was good. The tunnel was build with an xconnect l2tpv3.
we replaced our 2911 for a ME3600X few weeks ago following the advice of our backbone CsC contact, and we are now facing the following problem :
the configuration we used is not working any more : we can build the tunnel but the spanning tree BDPU are not passing through (We use rstp for spanning-tree protocol).
3925 : ______________
pseudowire-class backup-sro-ypa
encapsulation l2tpv3
ip local interface GigabitEthernet0/0/0.777
interface GigabitEthernet0/1
description interface connecting site B
no ip address
duplex auto
speed auto
no keepalive
no cdp enable
xconnect 10.193.32.50 5 pw-class backup-sro-ypa
interface GigabitEthernet0/0/0.777
description interface facing the CsC
encapsulation dot1Q 777
ip address 10.193.32.42 255.255.255.252
mpls bgp forwarding
ME3600 : ______________
pseudowire-class backup-ypa-sro
encapsulation l2tpv3
sequencing both
ip local interface Vlan777
interface GigabitEthernet0/1
description interface facing the CsC
switchport trunk allowed vlan none
switchport mode trunk
mtu 1512
service instance 777 ethernet
description *** Transport vers to CsC***
encapsulation dot1q 777
rewrite ingress tag pop 1 symmetric
l2protocol tunnel
bridge-domain 777
interface GigabitEthernet0/2
description interface connecting site A
no switchport
no ip address
xconnect 10.193.32.42 5 encapsulation l2tpv3 pw-class backup-ypa-sro
interface Vlan777
description vers RCV
dampening
mtu 1512
ip address 10.193.32.50 255.255.255.252
no ip unreachables
mpls bgp forwarding
As we have no experience with the ME3600X and their EVC and service instance concepts we have a hard time figuring out what solution to use :
- According to this post l2tpv3 is not supported on the ME3600X : https://supportforums.cisco.com/discussion/11919131/configuring-pseudowire-between-3800-router-and-me3600x
- According to this one it seems possible to interoperate a tunnel between a 2911 and a Me3600 : https://supportforums.cisco.com/discussion/11848451/eompls-and-layer-2-tunneling
Our need is slightly different though, as we are trying to pass a dot1Q trunk in the tunnel.
We tried to switch to encapsulation mpls, with no luck so far...
Any help or feedback would be greatly appreciated.
Best Regards,
Jérôme Schlumberger

News from the lab...
I decided to start again my config from scratch :
On the ME3600X___________ :
pseudowire-class backup-ypa-sro
encapsulation l2tpv3
ip local interface Vlan777
sequencing both
interface GigabitEthernet0/2
description *** Backup L2 VLans Internes avec RSROHES1 ***
no switchport
no ip address
no keepalive
no cdp enable
xconnect 10.193.32.42 5 pw-class backup-ypa-sro
On the 3900___________
pseudowire-class backup-sro-ypa
encapsulation l2tpv3
ip local interface GigabitEthernet0/0/0.777
sequencing both
interface GigabitEthernet0/1
description Tunnel_BB_HEIGVD
no ip address
duplex auto
speed auto
no keepalive
no cdp enable
xconnect 10.193.32.50 5 pw-class backup-sro-ypa
-> The "sequencing both" is mandatory to get the tunnel UP.
-> I configured l3 interfaces on the devices facing the ends of the tunnel and I can't ping them. Looking a little bit more carefully, I noticed that the arp table does not fill on the 3900, but it does on the 3600. I guessed that's a limitation on the 3600, but still not sure.
I then tried to switch to mpls encapsulation with the following configuration :
On the ME3600X_____________________________
pseudowire-class backup-ypa-sro
encapsulation mpls
interface GigabitEthernet0/2
description *** Backup L2 VLans Internes avec RSROHES1 ***
no switchport
no ip address
no cdp enable
xconnect 10.193.32.42 5 pw-class backup-ypa-sro
On the 3900___________
pseudowire-class backup-sro-ypa
encapsulation mpls
interface GigabitEthernet0/1
description Tunnel_BB_HEIGVD
no ip address
duplex auto
speed auto
no keepalive
no cdp enable
xconnect 10.193.32.50 5 pw-class backup-sro-ypa
This time, impossible to get the tunnel UP :
sh xconnect all detail :
XC ST Segment 1                         S1 Segment 2                         S2
------+---------------------------------+--+---------------------------------+--
DN     ac   Gi0/1(Ethernet)              UP mpls 10.193.32.50:5               DN
            Interworking: none                   Local VC label 147
                                                 Remote VC label unassigned
                                                 pw-class: backup-sro-ypa
Actually, as I am in a CsC architecture using BGB for label distribution with the CsC core, there is not ldp neighbor, and it seems to be the reason why I can't get the tunnel UP.
I am now trying to avoid ldp for the signaling of the tunnel using AToM Static Pseudowire Provisioning but I am to much of a newbie for that. I get a "Incomplete AToM manual config" when configuring the xconnect on the me3600...
Here is my config on the ME3600x so far :
pseudowire-class backup-ypa-sro
encapsulation mpls
protocol none
interface GigabitEthernet0/2
description *** Backup L2 VLans Internes avec RSROHES1 ***
no switchport
no ip address
no cdp enable
xconnect 10.193.32.42 5 encapsulation mpls manual pw-class backup-ypa-sro
! Incomplete AToM manual config
Funny, I tried to configure
RYPRC01(config-if-xconn)#mpls label 0 1048500
on the xconnect sub config section of the interface, but it won't appear in the config...
I am really stuck, and any help would really be appreciated.
Best Regards,
Jérôme Schlumberger

Phase 2 tunnel is not going up between PIX 525 and Watchguard

Hi Folks,
Can you please help me in knowing where is the problem liying, currently I am trying to establish a VPN tunnel between PIX firewall and Watchguard , all the parameters of both devices are the same though Phase two tunnel is not coming up.
here is the debug :
crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:500 dpt:500
OAK_MM exchange
ISAKMP (0): processing KE payload. message ID = 0
ISAKMP (0): processing NONCE payload. message ID = 0
ISAKMP (0:0): Detected NAT-D payload
ISAKMP (0:0): NAT does not match MINE hash
hash received: b3 8f bb 0 93 3b 65 e8 35 6f 54 6 c4 6f 59 cc
my nat hash : dd 70 9 ac 35 58 40 da 3b 5b fc 1b 4c 87 d2 11
ISAKMP (0:0): Detected NAT-D payload
ISAKMP (0:0): NAT does not match HIS hash
hash received: ba 72 c5 e 5b fb 88 f0 1e f7 8a ba c9 c6 c1 cc
his nat hash : c 4c 89 a5 66 c1 dd 80 76 48 3f a5 b0 f0 56 ed
ISAKMP (0:0): constructed HIS NAT-D
ISAKMP (0:0): constructed MINE NAT-D
return status is IKMP_NO_ERROR
crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500
OAK_MM exchange
ISAKMP (0): processing ID payload. message ID = 0
ISAKMP (0): processing HASH payload. message ID = 0
ISAKMP (0): SA has been authenticated
ISAKMP: Created a peer struct for 212.37.17.43, peer port 37905
ISAKMP: Locking UDP_ENC struct 0x3cbb634 from crypto_ikmp_udp_enc_ike_init, count 1
ISAKMP (0): ID payload
next-payload : 8
type : 2
protocol : 17
port : 0
length : 23
ISAKMP (0): Total payload length: 27
return status is IKMP_NO_ERROR
ISAKMP (0): sending INITIAL_CONTACT notify
ISAKMP (0): sending NOTIFY message 24578 protocol 1
VPN Peer: ISAKMP: Added new peer: ip:212.37.17.43/4500 Total VPN Peers:16
VPN Peer: ISAKMP: Peer ip:212.37.17.43/4500 Ref cnt incremented to:1 Total VPN Peers:16
crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500
ISAKMP (0): processing NOTIFY payload 24578 protocol 1
spi 0, message ID = 3168983470
ISAKMP (0): processing notify INITIAL_CONTACT
return status is IKMP_NO_ERR_NO_TRANS
crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 484086886
ISAKMP : Checking IPSec proposal 1
ISAKMP: transform 1, ESP_3DES
ISAKMP: attributes in transform:
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (basic) of 32000
ISAKMP: encaps is 61433
ISAKMP: authenticator is HMAC-MD5
ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP (0): SA not acceptable!
ISAKMP (0): sending NOTIFY message 14 protocol 0
return status is IKMP_ERR_NO_RETRANS
crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500
ISAKMP: phase 2 packet is a duplicate of a previous packet
ISAKMP: resending last response
ISAKMP (0:0): sending NAT-T vendor ID - rev 2 & 3
crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500
ISAKMP: phase 2 packet is a duplicate of a previous packet
ISAKMP: resending last response
crypto_isakmp_process_block:src:213.210.211.82, dest:212.118.128.233 spt:500 dpt:500
ISAKMP (0): processing NOTIFY payload 36136 protocol 1
spi 0, message ID = 287560609
ISAMKP (0): received DPD_R_U_THERE from peer 213.210.211.82
ISAKMP (0): sending NOTIFY message 36137 protocol 1
return status is IKMP_NO_ERR_NO_TRANSdebug
ISAKMP (0): retransmitting phase 1 (0)...
Thanks,
Ismail

Hi Kanishka,
The Phase 2 Parameters are the same also PFS is disabled !
There are some curious things in the debug msg, could you please throw some light on them
ISAKMP (0): Checking ISAKMP transform 1 against priority 1 policy
ISAKMP: encryption 3DES-CBC
ISAKMP: hash MD5
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP: default group 1
ISAKMP (0): atts are acceptable. Next payload is 0
ISAKMP (0): processing vendor id payload
ISAKMP (0:0): vendor ID is NAT-T
ISAKMP (0): processing vendor id payload
what does the vendor ID is NAT-T above mean ? Is it say that both sides are using Nat traversal.
Also in ecryption its says encryption 3DES-CBC
i am not sure if this CBC is the culprit. Because thats what watchgaurd uses only it does not have an option for only 3DES.
strange enought that Phase 1 is getting up, I am also questioning myself about the following message appearing in Phase 1:
ISAKMP (0:0): Detected NAT-D payload
ISAKMP (0:0): NAT does not match MINE hash
hash received: b3 8f bb 0 93 3b 65 e8 35 6f 54 6 c4 6f 59 cc
my nat hash : dd 70 9 ac 35 58 40 da 3b 5b fc 1b 4c 87 d2 11
ISAKMP (0:0): Detected NAT-D payload
ISAKMP (0:0): NAT does not match HIS hash
hash received: ba 72 c5 e 5b fb 88 f0 1e f7 8a ba c9 c6 c1 cc
his nat hash : c 4c 89 a5 66 c1 dd 80 76 48 3f a5 b0 f0 56 ed
ISAKMP (0:0): constructed HIS NAT-D
ISAKMP (0:0): constructed MINE NAT-D
return status is IKMP_NO_ERROR
how come Phase 1 is coming up though the PIX is claiming that his HASH is not the same as HIS HASH :(
the log messages on WATCH GUARD states that there is no proposal chosen!
why both firewalls are not friends?
I appreciate any input

Your client does not support opening this list with windows explorer - related to multiple uploads?

Hi folks -
I've read through some threads regarding "Your client does not support opening this list with windows explorer" and it seems a lot of folks have a lot of solutions throughout the forum posts. Is there anything official or semi-official regarding
this?
I've tried a lot of the fixes including:
checking to see if the WebClient service is on
modifying so-and-so registry (I've since changed them back since they seem to have no effect)
and changing various settings in Internet Options including making sure the site is in the Local intranet zone.
I could live without this functionality but just recently my upload-multiple-files functionality in SharePoint 2010 has also gone away (red x instead of directory UI). I wonder if it's related somehow and could give us a clue.
If it helps I'm using various browsers but of the IE flavor 8 and 9 32-bit as the base for testing this.

For SharePoint 2013 (so could apply to 2010 as well), my problem was that I was trying to "Open with Explorer"
something that probably can't be opened with Explorer. In my case, I just wanted to open my team's Shared Documents with Explorer. I found that when I first log into SharePoint and view the page, I'm presented with those Shared Documents, but also other things
as well.
To get "Open with Explorer" to work, I must click "Shared Documents" under the Libraries heading on
the left. Then, all the other stuff (Links, Getting Started, etc.) go away and I'm focused on my team's shared documents. From there, I can go up to the Library Tools section in the ribbon, choose the Library tab in the ribbon, and click Open with Explorer.
Works like a champ on Windows 7 64-bit, running IE 9 32-bit.
Unfortunately that's not what was going on in my case. One obvious way to check is to see if other people or other computers can Open with Explorer. In my case it was just this one machine on my desk that had the issue.

Pages 5.0 version does not support pictures in header

I recently installed new soft OS X Maverick and along with this also renewed soft for Numbers, Pages, Keynote, and some more apps.
Pages version 5.0 does not support its earlier version pre-set headers and footers. All the logos (picture files) I had inserted for my company template in the header are gone and I cannot re-enter them either. Does anyone can give e a hint on how to use picture files in Pages version 5.0 templates?
This is first time in 2+ years that I prefer to use MsWord over Pages on my Mac, which is a pity.
*I have tried to get used to new soft versions of numbers and pages now for around 3 weeks but it cannot make me to change my opinion that the eralier versions were much better. Unfortunately with OS X Maverick I have to use new versions for these apps, or do I, any hints?
I already deleted once (2 weeks ago) OS X Maverick and switched back to OS X Mountain Lion (I use TM), but then decided after while to still update the op system soft to newest one available, as I've hoped that developers in Apple will come up with their soft improvements and bug fixes soon enough.
Among the other disomforts (like pages, numbers and changed tag system) Safari is much slower than with previous version.
Any hints are appreciated!
Thanks, Paul

https://discussions.apple.com/message/21546508#21546508 check this out

IMAQ ClipboardToImage IMAQ Vision does not support the file type you specified.

Hi.
I have been trying out the inventeering INVENTvisionIMAQexample.vi. But i always encoutered
an error in the INVENTvisionVFWcopy.vi of "IMAQ ClipboardToImage IMAQ Vision
does not support the file type you specified." And the video window does not
appear full size with real-time capture image. Does anyone encountered this problem as well? Please enlightened me. Thank you.

What error it is throwing ? if you could attach the vi then it will be easy to find out the problem

SSRS 2014 Does not support vertical text in Chrome, Safari and FireFox

Why SSRS 2014 does not support "Writingmode=Vertical " forTextbox in Chrome, Safari and Firefox ?
It is showing horizontaly in all browsers. in IE versions it is vertical.

You can report such browser issues here directly to SSRS team:
What browser rendering issues do you need fixed?
Olaf Helper
[ Blog] [ Xing] [ MVP]

Does it support - million orders per week?

Hi friends
does sap support million sales orders per week?
and if so how to do that?
Thanks
Prasad

Hi
SAP will definitely support this, but the question is whether the organisation can produce/procure and manage such huge amounts of inventory. I really doubt why an organisation should create 1million orders per week i.e. 52 million order per year.
If you can explain you need so many orders, it will be useful to us.
This may also affect the system performance based on the servers, location etc.
Reward if this helps.

Does ACI support a VXLAN Tunnel between Leaf(Leaves) and VMware-vDS, and MS-vSwtich?

Similar Messages

Maybe you are looking for