Does airplay require wireless connection?

does airplay require wireless connection to internet?

For one, it doesn't need any connection to the internet. It's a local streaming protocol that works over your LAN. No internet required.
As for the wireless component, no. It'll work over a wired or wireless LAN.

Similar Messages

Hub Manager does not show Wireless connection

My 'Hub Manager' shows my Ethernet connected PC; my hub phone and the wireless connected printer.
My daughter has a new laptop which has wireless connection to my Hub. According to her laptop it is connected to my Hub and she has access to the internet.
However, my Hub Manager does not show her as connected to the Hub. The result of this means that she cannot connect to the wireless printer.
We have disconnected and re connected to no avail.
Any thoughts??? All help appreciated.

Hi
to get more replies suggest you repost on the broadband board
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

WRVS4400N does not allow wireless connections

I've had the WRVS4400N for about six months. Three times in the past two months I have had to factory reset the device and reconfigure it because it would not allow any wireless connections. Perhaps unfortunately I applied the latest firmware update about a month before these problems began. Is there any work-around or setting change that I can make to avoid this problem? When wireless connections are impossible the device is still reachable via the ethernet connection.

If only the wireless is dorpping on the unit then, most probably a firmware concern. Try reflashing the firmware again if that helps. Also try to change some of the advance wireless settingso nthe router, set the RTS and fragmentation to thresholds to 2306 as well as teh beacon interval to 50.

HP Envy- does it require internet connection for the air print feature to work?

I am considering purchasing an HP Envy printer, but I live in an area with limited internet service (very slow dial-up). Does the Envy require an internet connection to work? I have a Macbook Air, and am assuming that I can just use my wireless router without connecting it to the internet. Has anyone out there used the air print in this situation?

Hi,
It should work without internet just a home network should be ok.
Regards,
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

WRT54G does not allow wireless connections

I installed a WRT54G V8 for my neighbor. After much pain and fights with the wizards I got it to where it works with wired computers. I set up the wireless and named it, selected security, recorded the Key, even had the wizard record the computer setup program on a USB drive.
The two wireless computers I have tried can both see the network but clicking connect does not get me the enter key window. Actually nothing happens after showing connecting for about a minute. I tried the setup program and it said it could not set up the computer. I tried setting up the parameters manually and then connecting nothing happens.
But the routers DHCP table shows the names of the two wireless computers as being connected.
Some time when I try to connect (with manual entered data) the network page will show "Not Connected" over the top of the network name. But the button at the bottom of the page has switched from "Connect" to "Disconnect" and the machine is in the DHCP table.
Any suggestions?

Greyhair wrote:
I am using XP SP2 on both of the wireless computers and I am using the default windows client. In the wireless networks tab is where we tried setting up the network manually. Are you saying that with a WRT54G I can have only one wireless network installed on the machines?
I will try it on one of the machines this afternoon when I go over to try again to get it to work.
Why is this so hard!??!
Hi greyhair ,
Ridcully did provide some good information.
The wireless network tab .
for that ,
strt>control panel>network connections or (network and internet connections) icon> network connections
Right click on the wireless network connection listed
go to properties ,
here you will find three tabs - general >wireless networks>advanced
you need to click on Wireless network
and remove preffered networks from the network list (even yours )!
and click ok !
and again , right click on wireless network connection > go to View aivialable wireless networks ....try connecting to your network by first clicking (highlighting)
on the network name , and then click connect.
any problem , feel free to ask here.
pe@c3
~~~Nobudy's Perfect , i try To Be So ! Each n every moment of maH LYF , AND I THINK dat wats make Me "Different" From others....~~~

New XTier Apache2 Module - does it require SSL connections?

Scenario:
NW 6.5 SP5
eDir 8.7.3.8
ZfD 6.5 SP2
Issue:
TID #: 2973878
New Apache2 xtier module for NetWare 6.5 SP5 released for LDAP over SSL .
Details:
After applying the new MOD_XSRV.NLM (228187 byte/17. may 2006 6:35:47 pm),
the Middle Tier clients can no longer login to eDir!
Backrev. to the old version solves the problem.
We do not use SSL for the Middle Tier LDAP connections through the ZfD Agent,
but use cleartext connections over port 389.
This patch was applied due to general maintenance/patch level, although we actually don't
need the SSL option for the moment.
But does this new MOD_XSRV.NLM actually require use of SSL,
or is it supposed to handle both cleartext and SSL LDAP-connections?
In other words, can it be used at all if we don't use SSL for Middle Tier connections?
- Erik

Erik Aaseth,
>TID #: 2973878
>New Apache2 xtier module for NetWare 6.5 SP5 released for LDAP over SSL .
This update is only for ZFD7. So no worries.
The TID doesn't state this so it will be updated.
Jared Jennings
Data Technique, Inc.
Novell Support Forums Sysop
http://wiki.novell.com

Laserjet p1102w does not maintain wireless connection with macbook pro

Above product was set up and working. If it sits idle for awhile it does not print. I have to click on WiFi signal, select hpsetup, then after that is complete reselect my network and then it prints. Printed self test page - device is 'connected'. Running OS 10.7.3

Yes. I had troubles getting it to work originally and I had to talk to someone at HP who helped me with it. We ended up setting it up manually and it worked fine; but if I don't use it for awhile it will not print. Actually that is not entirely true. Once in awhile it will - about 10% - but most of the time it will not unless I do the above.

Does airplay work with airport express without wifi?

I would like to stream music from my Macbook Air to my stereo using Airport Express. However, it is my weekend home in which there is no wifi connection. Will it still work or does Airplay require a wifi conenction to the internet to work?

Yes, you should be able to get it to work. I tried it just now with an older AirPort Express, and it works for me, but the configuration and settings are rather unconventional.
Set the AirPort Express to create a wireless network with no security code— it may work with one but maybe not. Configure the AirPort Express in Bridge Mode with respect to the Internet, and assign it a static IP address of, say, 192.168.4.1.
I made a wireless connection to the AirPort Express from an iPhone 5 and was able to play music from my iPhone to speakers attached to the AirPort Express. Interestingly, the iPhone doesn't actually make a full connection to the AirPort Express but the wireless network name shows up in its Settings.
The iPhone has a self-assigned 169.x.x.x IP address, but I am able to choose the AirPort Express-attached speakers from the Music app on my iPhone.
There may be a cleaner way to do this, but one way or another you should be able to get it to work.

7525 Wirelessly connected, loses internet connection, will not print from wireless network

Have a 7525 Photosmart printer (approx 7 months in service) that has been working great until now. I had to change the dsl/wireless router over the weekend and now I can't print wirlessly from the network. According to the printer diagnostics, the printer is connected to the network but each time I try to print, the computer being used can't find the printer. Checking the Wireless Network Test Results page, all is fine except there is no internet connection. Restoring the internet connection requires a 're-boot' of the printer, i.e., switching it off and unplugging, after which network printing is restored. However, that only lasts for a very short time, less than 1 minute, then no more network printing.
I think there is something fishy with the IP address. HP Print and Scan Doctor can't find the printer using this address. Typing the IP address into the browser gets an error message that the page cannot be found. That address should lead you to the printer page, but it does not. Changing the router resulted in an IP address change for the printer, but I wasn't even able to manually set the IP address via HP troubleshooting as it required the ability to get to the printer page from the IP address.
I am rambling on, but I have reached my knowledge limit and hope that someone can give me some other suggestions on what to try next. Thanks

Hi Seenders and welcome to the HP Forum,
I understand that you are having connection issues with the printer on the network. I will try my best to help you resolve this issue. In this document for Printer Does Not Maintain Wireless Connection are different solutions that may resolve your connections issues. Once you have the printer up on the network make sure you update the IP Address on your computer.
I hope this information is useful. Let me know how it works out.
Thank you,
I worked on behalf of HP.

Hp office jet 6700 (Mac)-wireless connection keeps failing...

Hi-I am hoping that someone has a solution for this. We have an HP Officejet 6700 that has worked flawlessly till last week. The wireless signal keeps dropping. I think that is the issue because if I go into Setup on the printer itself and go to Network and start all over with finding my router, it works fine. For one print job. Then if I have something something else to print I have to go through that whole setup routine again.
If I just go to Print it says locating printer and then it says that the printer is not connected. What is going on?? Very frustrated. I tried uninstalling and reinstalling the driver (I downloaded the driver from the HP website). That didn't fix it. I saw that there was a firmware update but couldn't install it even though I plugged my laptop into the printer with a USB cord.
Something is going on that I don't have a clue in how to fix it. I really appreciate any help. Thank you, Judy

Hi mrstucci,
I would to help you establish a more consistent connection between your Officejet 6700 printer and your Mac. Please use the following document to troubleshoot the issue; Printer Does Not Maintain Wireless Connection.
If the issue persists, please also take a look at this helpful document; 'Printer is offline' Message Displays on the Computer and the Printer Does Not Print: Mac OS X.
Please let me know if this resolves the issue of if you require further assistance. Thanks.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Printing with HP Deskjet 1510 from wireless connected ipad using computer connected to broadband

Hi,
I am trying to figure out easy way to print any content from my ipad connected with wifi through xp computer to HP Desjket 1510,

Hi Ieb_Fabulous,
Welcome to the HP Support Forums. I gather you are trying to hook your Deskjet 1510 printer to your laptop with a wireless connection.
This printer does not support wireless connectivity. I have included the Deskjet 1510 Printer Specifications for your reference.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Deskjet 3050 wireless connection trauma

Hi, my Deskjet 3050 has stopped working over the wireless network and I'm stumped. It was working fine, but has now stopped. My laptop is connected to the home router (BT) and the printer is also connected to the same router (according to the router config page), but I can't connect to print. I've gone back to the beginning and re-installed the printer and all drivers and software, I can print with a USB, I can transfer wireless config details via USB, but I still can't print wirelessly. Help?

Hi PG-PG,
I understand that you are having a problem with getting the printer working on your wireless network. I will try my best to help you resolve this. I suggest power cycling your network.
How to power cycle network
Follow these steps to reset your HP printer, your wireless router, and your computer.
1.Press the Power button on the HP printer to turn it off.
2.Disconnect the power cord from the rear of the HP printer.
3.Disconnect the power cord from the wireless router.
4.Turn off the computer.
5.Wait 30 seconds.
6.Reconnect the power cord to the wireless router.
7.Wait 30 seconds, or until the router is fully on and ready.
8.Turn the computer back on.
9.Wait for the computer to reload.
10.Reconnect the power cord to the rear of the HP printer.
11.Turn the printer back on.
If this does not resolve the issue then I suggest setting a Static IP Address. In this document for Printer Does Not Maintain Wireless Connection has steps for setting that up.
I hope this information helps, please let me know how it goes.
Thank you,
I worked on behalf of HP.

Color Laserjet Pro 100 (M175NW) looses wireless connection

Hi,
the printer goes offline from the local wlan after working ok 12 to 24 hrs.
symptoms:
* wireless LED on the printer blinking after waking the printer with the ok button
* wireless status page: not connected
* wireless status page: no wireless lans are found (minimum four others are active)
* wireless status page: always 69-71 disconnects (link quality is good, distance from router 5m)
* wireless lan switched off-on from printer panel: wireless led stays off, no blinking
my tests:
* no difference with/without power save mode
* no difference using router from TP-Link or Arcadyan
* no difference using no/standard/long group key interval on the router
* no difference using only ip4/all services on the printer
* no difference enabling/disabling ip6 on the printer
* no difference printing/not printing during 24 hrs
* no difference using channel 1/7 on the wlan (no other networks on these channels)
workaround:
printer off - on, everthing back to normal, but I am not happy with that
My settings
* printer firmware new: Version:20120806
* static ip
* wpa2-personal aes
* windows vista all patches installed
* current hp printer driver
* wlan settings transferred via usb during standard install
my guess:
buggy firmware or defective network card in the printer
Any ideas? Device is on warranty...

Printer does not maintain wireless connection.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02817031&tmp_task=solveCategory&cc=us&dlc=en&la...
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

HP Officejet Pro 8600 Plus losing wireless connectivity, cannot scan to computer

In our office, we have roughly 4 computers using the HP Officeject Pro 8600 Plus, all of which are connected wirelessly. The printer was previously connected to the internet wirelessly with no problems. A couple of days ago however our computers started randomly disconnecting. The printing function would work for a bit, then disconnect. I found the only solution to this problem was to hit the button on our wireless router that resends the wireless signal out for connectivity.
We hardwired the printer with an ethernet cable and I myself didn't see any further problems regarding connectivity but a couple of the other computers had spotty connections. Again, each time this can be remedied by hitting the button on the wireless router.
Today however we had an additional problem, after trying to scan a document through the automatic document feeder, the printer said it was jammed (although it wasnt). When we went to rescan, the scan to computer function was no longer working. I can scan by hitting the scan button on my HP Printer Assitant interface, and I can also scan to email, but cannot scan to computer.
I have gone through several forums and haven't been able to find a solution. I personally use Windows 8, but other people in our office are using older versions of Windows. We've tried unplugging, restarting, hardwiring, resetting wireless settings, uninstalling, etc. etc. Before a few days ago the pritner was working fine for a number of months.
If anyone has any ideas they would be greatly appreciated.

Hi rtaw,
Welcome to the HP Forums!
I understand that you cannot scan to computer, and that you are losing wireless connectivity, with your HP Officejet pro 8600 Plus. I am happy to help you with this issue!
Please take a look through this wireless guide. Printer Does Not Maintain Wireless Connection.
For the scanning, please see this guide. A 'Connection Error' or 'No Computer Detected' Error Message Displays during Scanning.
Hope this information helps you, and let me know if you have any more issues!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

HP OfficeJet Pro 8600 Wireless Connection Problems

Started having problems scanning. Then problems printing from my desktop - Unable to find printer. Uninstalled / Re-installed HP Software / Drivers; Desktop is still unable to find the printer - During setup: The IP Address is either incorrect or it is from a different wireless network that has the same name as your network.
I have verified the following:
The IP Address of my Desktop and Printer are the same except the last number
The HP Scan and Print doctor sees the printer and indicates all is functioning normally
I can see the printer via web browser and the printer's IP address on my desktop
I can print to the printer via wireless from my iPad and laptop
The only issue is configuring the printer on my desktop and actually printing from it.
Thanks in advance for your assistance.
This question was solved.
View Solution.

Hello NorseGuy ,
Please let me take a moment to say "Welcome" to the HP Forums.
I hope you enjoy your experience!
I see that you are having an issue with staying connected on the wireless network.
First off, please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
I would also suggest going through the following document for troubleshooting the Printer Does Not Maintain Wireless Connection
Please feel free to write me back if you have any other questions or concerns.
Thank you.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Does airplay require wireless connection?

Similar Messages

Maybe you are looking for