Does Cisco UCCE 8.5 Virtual Machine support VMXNET3 driver?

Does Cisco UCCE 8.5 Virtual Machine support VMXNET3 driver?
VMware ESXi 5.0

Saeed,
about " can you provide with link which highlight the current support VM for UCCE. " not sure if I understood you right, but if you wanted to know which are all the UCCE components can be virtualized on VM, then please refer " Contact Center Applications " section of http://docwiki.cisco.com/wiki/Unified_Communications_Virtualization_Supported_Applications
Pls remember to rate helpful posts.
GP

Similar Messages

Does Cisco 3845 with NM-16A/S support OIR feature or Hot swap for this NM.

Dear Sir
My customer would like to implement Cisco 3845 with NM-16A/S x 4. I found that Cisco 3845 support OIR function but I am not sure OIR function that Cisco 3845 support, it support with which NM models. Can anyone tell me that NM-16A/S on Cisco 3845 support OIR function on this NM or not.
Thank you very much
Wisit

Hi,
From what I have read from the following document.
http://www.cisco.com/en/US/products/ps5855/products_installation_guide_chapter09186a00802ccf1d.html
Network Modules
Network modules install directly into slots in the rear of the router. The Cisco 3845 router supports online insertion and removal (OIR, or hot swap) of network modules. The Cisco 3825 router does not support OIR.
Caution The Cisco 3845 router supports OIR with similar modules only. If you remove a network module, along with any installed WAN or voice interface cards, install another module and card combination exactly like it.
Interface Cards
Cisco 3800 series routers do not support OIR (hot swap) of interface cards inserted directly into router slots. You must turn off the router before installing or removing an interface card.
The Cisco 3825 router and the Cisco 3845 router each provide four interface card slots, labeled on the rear panel by HWIC and a number. Each slot can be occupied by one single-wide WIC, VIC, VWIC, or HWIC.
Hope this helps
Sarb

MDT 32bit boot image does not boot type 2 virtual machine in hyper-v

I created a type 2 virtual machine on a windows server 2012 R2 and tried to boot it with MDT 32 bit (x86) boot media and it will not boot.
Same media works if I use type 1 virtual machine .
Is this expected behavior ?
Thanks

Hi,
Yes as Gen 2 machines only nsupports only x64 os and the following OS:s
Windows Server 2012
Windows Server 2012 R2
64-bit versions of Windows 8
64-bit versions of Windows 8.1
-- My System Center blog ccmexec.com -- Twitter
@ccmexec

Does Cisco Cloud E-mail Security Solution Support IPv6?

For the Cisco Cloud E-mail Security Solution - does it support both inbound and outbound IPv6? Are there any limitations? I know the IronPort E-mail Security Appliances supports IPv6 - but specifically interested in the cloud service.
Thanks,
--Jim

arkhane wrote:
Hi.
Does anyone could explain me about SSL/TLS?
Here is the situation:
E72 allows in securîty settings to select SSL/TLS. I selected it for both accessing and sending mails and I can logon to my POP and send with SMTP. So apparently no problem.
But I asked my internet provider if they support SSL/TLS and they told me no they does not support it....so my question is does really SSL/TLS works in my situation and my provider has no clue on security settings or SSL/TLS does not work but it has no incidence on using my mails as I said I can receive mails and send mails even if those security settings are selected...?
Thanks if anyone could explain me this.
Some e-mail providers like Gmail use SSL/TLS.
http://mail.google.com/support/bin/answer.py?answer=13287
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

Does the ARRIS TG862 provide time machine support?

I am trying to see if I can get rid of my airport extreme (4th gen) and just use the comcast provided Arris TG862 modem/router. I use VOIP and Time machine but through the Airport Extreme.
Any help is appreciated,
Thanks,
-Scott

The first question would be whether the Arris TG862 provides a USB port for a shared network hard drive......which, based on the limited amount of online information available.....it does not appear to do.
If you have the 862 handy, you could perform a quick check.
I am not sure how VOIP would tie into the Arris product....or the AirPort Exteme for that matter, so can't help on that one.

AnyConnect VPN on Mac - Can't SSH to Virtualbox Virtual Machines

Hi,
I'm running AnyConnect version 3.1.05170 on my Mac. I'm also doing SW Development on multiple Virtual Machines on my Mac via VirtualBox. When I connect via VPN, I can no longer SSH to my Virtual Machines. I'm sure there is a rules setting or something that is killing my "Host Only Network" in VirtualBox so I can no longer access them. The worst part is that even if I Quit the AnyConnect Client, I still can't SSH to my Virtual Machines, so whatever rule is put in place doesn't go away when I disconnect the tunnel.
Has anyone witnessed this or have a suggestion on how to go about solving it?
Thanks,
- Curt

Hello,
I just encountered the same problem. To solve it, I checked the box "Allow Local (LAN) access when using VPN (if configured)" in the preferences of AnyConnect.
It's working fine for me but I am using Parallels and not VirtualBox.
Regards
David

How do I get virtual memory support?

I am trying to run a new version of Parallels (8). When I try to start it, it says virtual machine support is turned off. How do I turn it back on?

I am having exactly the same problem!

Java card virtual machine

java card virtual machine
Is java card virtual machine support java code written in a java standard edition....
and what are the features and specification of java card virtual machine
how to get the java card virtual machine sdk and work with that in netbeans

1.Whether JCVM is Portable to different platform?Are you a java card user or a java card manufacturer?
As user this is not your concern. the JCVM is an inseparable part of your java card.
3.What is the use of Cref in JCVM.Whether that helps in portability?CREF is the "Java Card Reference Implementation". It allows you to run java card applets by simulating a java card environment on a common PC. It's intention is to be executed in an environment with an 32bit processor and lots of ram (compared to current smart cards). IMHO cref can not be ported to any current smart card platform.
Jan

Install R12 on a Virtual Machine hosted on Windows Vista

I wanted to install Oracle EBS R12.1.1 on Windows Vista Home Premium 64-bit but used to get .\jre\nt\1.6.0\bin\java error. Hussein Sawwan
helped and said that this is not certified. He adviced me to create a VMWare Server. Following is my experience. I hope it is helpful. Any
suggestions, additions are more than welcome. Thanks to all who helpmed me especially Hussein Sawwan, Helios, Gareth Roberts.
I used to get .\jre\nt\1.6.0\bin\java error after the installation would zoom through 33%. That was because my staging area was not correct. The staging area should be just next to c:\ or whatever be the root directory (or drive). No space or special characters in folder name. My current structure is as follows:
c:\r12stage. Under r12stage I have following folders and subfolders
oraAppDB -- 49 Disks
oraApps -- 11 Disks
oraAS -- 3 Disks (This comes from the Rapid Install Tools)
oraDB -- 5 Disks
startCD -- 1 Disk plus other folders. Just copy startcd from the unzipped download and paste to r12stage area.
I then created a virtual machine using VMWare Server (free download but need to register to get the serial number). Because I installed
vmware server on Vista Home Premium 64 bit Host OS, I have to boot my machine by pressing F8 and then select Disable Digital Signature
Enformcement. Thanks to Gareth Roberts for this tip. Create a vm and install Windows 2003 by selecting the .img file (first cd) by selecting Use ISO image and then path of the windows 2003 cd 1 (zipped file). start the virtual machine, that will install windows 2003 and then ask for location of 2nd cd. On the host machine, where the second win 2003 zip file resides, unzip the second zip file and name the folder as cd2. share this folder to the __vmware_user__ and from the virtual machine, map network drive to \\hostmachinename\cd2. Select this as the location of cd2 and complete the installation. Install MKS Toolkit from http://cygwin.com/ and visual c++ from Microsoft website. for information on this please refer to the following URL. Thanks to Muhammad Habib
http://mhabib.wordpress.com/2007/03/14/installing-oracle-applications-e-bussiness-11i-on-windows-xp/
After installation is done and Windows Update is run, share the r12stage directory on the host machine to the vmuser and launch rapidwiz.cmd from the command prompt and follow the instruction. For internet connection from the VM use Ethernet as NAT.
If the installation errors halfway through, clean up your VM by following instructions in document id 292424.1 in MetaLink. If you dont have access to Metalink then I summarize the steps briefly over here.
Launch the Registry Editor.
Navigate to the HKEY_LOCAL_MACHINE\Software key.
Select the Apache Group subkey and delete it.
Select the Oracle subkey and delete it.
Navigate to the HKEY_LOCAL_MACHINE\System\Current Control Set\Services.
Carefully select and delete each service beginning with Oracle. For example, delete "Oracle Apache Server PROD_<nodename>".
When you are finished, exit the Registry Editor.
Navigate to the Environment Variables editing screen according to your system setup. For example, right-click My Computer and select
Properties. From the Advanced tab, click the Environment Variables button.
Select the following system variables if created during the failed installation, and delete them: DISCO_JRE, DISCO_VBROKER, JSERV,
VBROKER_JAVAVM, VBROKER_TAG, WV_GATEWAY.
Select the Path variable, but do not delete it. Carefully edit it and remove any component with "Oracle" in the name, or that otherwise
references the failed install. For example, delete "E:\11.5.10\test\visora\8.0.6\bin;".
Save and exit System Properties.
Open a command window and navigate to the C:\Program Files\ directory. Delete the Oracle subdirectory.
If your Oracle Inventory directory was not C:\Program Files\Oracle\Inventory and was therefore not deleted in the previous step, locate it
and delete it.
Restart your machine
It is now safe to remove the Oracle filesystem that was partially installed during the failed installation. Go to the base install directory,
or top-level directory under which you installed either the Database Server (DATA, DB) or the Applications Tier Server (APPL, ORA, COMN)
directories, or both. Note that you may choose to rename a directory before you delete it. This allows you to use the same directory name and start a new installation even before you finish the delete filesystem operation. For example, if you placed your filesystem in a "test" directory under
"E:\11.5.10":
C:\> E:
E:\> cd 11.5.10
E:\> rename test oldtest
E:\> del /s /q oldtest
In another window:
C:\> cd <stage install directory>
Q:\> rapidwiz.cmd
After cleaning up if you still get error like RW-50004: Error Code received when running external process. Check log file for
details. Running database Install driver for VIS instance, after 13% complte step 1 of 5 then I suggest that you re-create the machine and follow the above steps again. Including installing win 2003, mks tool kit , vc++, etc. It will be a success.
Starting concurrent manager takes up enormous memory and slows down everything, so if you dont need it then dont ever start it. APPS password is apps and sysadmin user is sysadmin.
Good luck.
Mahesh Acharya

I had Vista 64-bit machine, installed Ubuntu in VMWare. Installed Oracle apps on 32-bit Ubuntu under VMware and was able to access Oracle apps. But, it is very very slow. It hangs sometimes and takes 15-20mins to display Ubuntu screens. Am I missing something here. I have a 4GB RAM and VMWare can not use all the 4GB. It may be using 2GB of 4GB. Am I missing something?

No sound in Virtual machine of Macbook after 10.5.1 update

Hi
I am using new macbook (C2D 2.2 GHz, 4G ram, 160 HDD, X3100 video) with Leopard.
When I installed virtual machine "VMware Fusion" to use boot camp windows partition, I could use boot camp windows as a full window(boot camp) and virtual machine(VMware Fusion's bootcamp partition use) fully.
However, after installing Leopard 10.5.1 update, I can't hear any sound from my virtual machine.
VMware Fusion is showing "Sound will not be available" !!!
So, I installed windows XP in virtual machine's image(not bootcamp).
BU, still no sound.
I think 10.5.1 update interfere virtual machine's sound driver or related driver.
Anyboy know this situation?

Peggy,
I didn't repair the permissions until I experienced the problems with Pages after the initial installation. After I did this, things worked fine. Like I said, after updating to 10.5.1 yesterday, the problem returned and after repairing permissions didn't get things back to normal, I reinstalled iWork '08.
Here's something odd. Even though I trashed the entire iWork '08, when I reinstalled, the installer told me that zero space was required to install iWork '08. So maybe there's some other disk issue involved?
The Repair Disk option is grayed out in Disk Utilities. There's an instruction to run the reapir application from a CD or DVD, but Leopard only has one installation disk and it doesn't have any independently running repair program on it.
Leigh

"This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible. This host does not support Intel VT-x"

Hi, I have installed vmware 5.5 hypervisor on hp G8 microserver. I have created one vm as windows 2008 R2. I have also install vmware workstation 11 on this vm. In this workstation when I tried to run vmware 5.5 hypervisor I come across "This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible. This host does not support Intel VT-x" this statement. Which shows that the host machine does not support virtualization and for that you need to go in Bios and enable it but in present case as host machine is also a vm and you would not find much detail of Bios when you log into the Bios therefore, I am pretty much stuck here. I don't see any information in relation to this. Now my question is:
1. Can we run ESXi inside a vm which is already sitting on ESXi?

I moved the discussion from VMware Workstation to Nested Virtualization which contains several hints on what's possible and what needs to be configured to make things work.
André

Does the GT780DXR support virtual machines.?

I want to use the GT780DXR as my main laptop, and I do a lot of virtual machine work with VMware.
I know that some manufactures block or disable VT options in the BIOS.
Before I buy can some one confirm that this option is available and can be enabled.
Thank you.

Thanks Bas.
I would prefer if it was a BIOS option, or just enabled by default.
I was also looking for an MSI pre-sales email address, but I couldn't find one.
If I am spending this much on a new laptop, I don't want to leave it to chance or a custom firmware.
Thanks.

Why does IE8 running on XP and Win7 Virtual Machine deletes the history while I'm still browsing the same site with client-side hashbang routing?

Hello,
I have a asp.net mvc 5 web application running on .net 4.5 hosted on my local windows 8 machine on macbook pro using parallels. I'm running Internet Explorer 8 Version: 8.0.6001.18702 running on XP and Version: 8.0.7601.17514 running on Windows 7 Enterprise.
I've got both of the virtual machine source from www.modern.ie
My web application is attempting to provide single page user experience by having some client-side routing by using '#!/xxx' hashbangs in the url so that I can get and post via ajax and change the hash in the url without causing the page to reload. My
code works fine in IE9+ and other modern browsers.
However, I'm facing this strange issue in both of the IE8 versions. When running my demo app in IE8, I can login, view home page and can navigate from this home page to many details page. From the very first login page, all the pages are the result
of form's post action via ajax which then expects html from server and loads in the DOM. The page structure of my app is like summary form => Details page (can also contain summary forms) => Details...so on.
The above process works fine for few of the navigation steps. If I keep navigating from one page to another & go back, I have observed that the browser back button is removing the history items slowly. And a time comes when it totally forgets about
all the history pages that I visited to reach this current page I'm viewing!! It treats like I have just started my browsing session and this current page is the first page I've landed on with no back option. Now if I again try to navigate, I have encountered
problems like both the back and forward buttons gets disabled.
Hope, my words above is clear enough to explain this problem. The same application works fine in IE9+ and other browsers.
Till now, I have tried following steps on both VMs:
Resetting IE8.
Increasing disk space to 1024mb for temporary internet files storage.
Setting 'Never' for Check for newer versions of stored pages.
Disabling the automatic crash recovery feature didn't helped in this case. Found this on support website.
Deleted temporary files, history, cache, etc many a times.
Search many forums, posted question on StackOverflow, ASP.NET
Forums - but didn't helped.
Tried 'beforeunload' event of browser to see if any of the page is reloading because of submit or any other reason. But the page doesn't reload at all.
The issue is browser forgets about the browsing history while I'm still browsing the same site.
Is there any possible fix for the issue above? Does IE8 have any issues as many ajax form post is happening on every page?

I have really tried many things to identify any possible reason of the issue above. Even rewrote all my javascript navigation code and checked server-side code.
But the only place where I got the solution is at site: http://www.enhanceie.com/ie/bugs.asp which states that there is a bug in IE8 which reads like:
IE0012: IE Travellog broken when navigating back/away from a page with
a large POST form If there is a form input field with a value longer
than 523,659 characters, when you navigate away from the page, IE may
clear the current session's travellog (similar to history), disabling
the back and forward buttons. Repros in IE6 & IE7.
There are following solutions that you can go for:
- Check for the input field that has lots of characters as mentioned above and solve your problem.
- If you have control over the system where IE8 will be used, you can add the following registry key on that machine. There is no existing key, so, you need to add a new one:
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\TravelLog] "MaxSize"=dword:ffffffff
I am really relaxed to find this information as I spent really long time to solve this issue. Hope this will help someone.

Server 2012 cluster - virtual machine live migration does not work

Hi,
We have a hyper-v cluster with two nodes running Windows Server 2012. All the configurations are identical.
When I try to make a Live migration from one node to the other I get an error message saying:
Live migration of 'Virtual Machine XXXXXX' failed.
I get no other error messages, not even in event viewer. This same happens with all of our virtual machines.
A normal Quick migration works just fine for all of the virtual machines, so network configuration should not be an issue.
The above error message does not provide much information.

Hi,
Please check whether your configuration meet live migration requirement:
Two (or more) servers running Hyper-V that:
Support hardware virtualization.
Yes they support virtualization.
Are using processors from the same manufacturer (for example, all AMD or all Intel).
Both Servers are identical and brand new Fujitsu-Siemens RX300S7 with the same kind of processor (Xeon E5-2620).
Belong to either the same Active Directory domain, or to domains that trust each other.
Both nodes are in the same domain.
Virtual machines must be configured to use virtual hard disks or virtual Fibre Channel disks (no physical disks).
All of the vitual machines have virtual hard disks.
Use of a private network is recommended for live migration network traffic.
Have tried this, but does not help.
Requirements for live migration in a cluster:
Windows Failover Clustering is enabled and configured.
Yes
Cluster Shared Volume (CSV) storage in the cluster is enabled.
Yes
Requirements for live migration using shared storage:
All files that comprise a virtual machine (for example, virtual hard disks, snapshots, and configuration) are stored on an SMB share. They are all on the same CSV
Permissions on the SMB share have been configured to grant access to the computer accounts of all servers running Hyper-V.
Requirements for live migration with no shared infrastructure:
No extra requirements exist.
Also please refer to this article to check whether you have finished all preparation works for live migration:
Virtual Machine Live Migration Overview
http://technet.microsoft.com/en-us/library/hh831435.aspx
Hyper-V: Using Live Migration with Cluster Shared Volumes in Windows Server 2008 R2
http://technet.microsoft.com/en-us/library/dd446679(v=WS.10).aspx
Configure and Use Live Migration on Non-clustered Virtual Machines
http://technet.microsoft.com/en-us/library/jj134199.aspx
Hope this helps!
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Lawrence
TechNet Community Support
I have also read all of the technet articles but can't find anything that could help.

Watchdog message at startup Virtual Machine Cisco Prime Infrastructure

Hello,
Anyone experience with the following messages when power on the virtual machine where PI is installed on:
Cannot setup NMI watchdog on CPU 0
Cannot setup NMI watchdog on CPU 1
Cannot setup NMI watchdog on CPU 2
Cannot setup NMI watchdog on CPU 3
This messages are seen through the console, Cisco PI seems to work fine.
Cisco PI 1.4
ESX 4.1
Kind regards,
Michel

Cisco PI is baked into Linux VM and this is a known issue with Linux VM with VMWare.
The details are mentioned here :
http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=2031297
However, this chnages are quite not supported by PI VM. Also, this is just a notification and can be ignored.
-Thanks
Vinod
**Rating Encourages contributors, and its really free. **

Does Cisco UCCE 8.5 Virtual Machine support VMXNET3 driver?

Similar Messages

Maybe you are looking for