Does DW have guides?

Looked everywhere and nothing under help - does it have
guides like in any other Adobe package, which u pull down from the
rulers top and left?

Deansplit wrote:
> Looked everywhere and nothing under help - does it have
guides like in any other Adobe package, which u pull down from the
rulers top and left?
Dreamweaver 8 does. You just pull them down from the rulers
just like
any other Adobe prog.
David Powers, Adobe Community Expert
Author, "Foundation PHP for Dreamweaver 8" (friends of ED)
Author, "PHP Solutions" (friends of ED)
http://foundationphp.com/

Similar Messages

I'm trying to install OS 10.6 onto my Macbook, which currently has OS 10.5.8. I clicked install (on the DVD) and selected my Macintosh HD drive. I was given the message that that disk cannot be used because it does not have the GUID partition????

I'm trying to install OS 10.6 onto my Macbook, which currently has OS 10.5.8. I clicked install (on the DVD) and selected my Macintosh HD drive. I was given the message that that disk cannot be used because it does not have the GUID partition. In order to have a GUID partition, it suggested I go to disk utility and make the change. I couldn't see the partition tabs in the disk utility application. So how do I accomplish the GUID partition?

The problem is, reformatting the partition may require you erase the hard drive. Normally Intel Macs are preformatted GUID. The fact that yours is not, says someone who initially installed the system on your Mac did you a disservice. Regardless, you should backup your data before you upgrade. GUID formatted drives generally are not compatible with iBooks (pre-2006 consumer notebooks by Apple) Powerbooks, and PowerMacs, and iMac G5s. So if you indeed have machine with the MacBook name on the screen frame, it was not properly formatted from the beginning.

Does ps have quick and guided mode? Or can I add this mode?

I am newbie. I have not used ps before. I tried ps elements and it's very good.
But considering I will update this sw annually, photoshop cc may be better as for price.
So I have a question.
Does potoshop cc have quick and guided mode? Or can I add this mode?

No, Photoshop does not have Quick and Guided modes. There isn't Organizer in Photoshop either but you have Adobe Bridge instead.

HT2434 does anybody know what happens if I dont update the firmware of my macbook pro (does not have a guid partition scheme))

does anybody know what happens if I dont update the firmware of my macbook pro (does not have a guid partition scheme)?

Apple will hire a high school girls clique to follow you around, make fun of you & post disparaging comments on Facebook .

The security database on the server does not have a computer account for this workstation trust relationship

When I try to log on to my DC it says "The security database on the server does not have a computer account for this workstation trust relationship". It won't let me log on. I installed another server server 2012r2 (its virtual )
and I can get to ADSI edit.
I think what happened was I had a pc that could not connect without unplugging the network cable. So I found this fix
FIX: “The security database on the server does not have a computer account for this workstation trust relationship”2032011
I’ve seen a lot of solutions, or suggestions rather, with regard to the error in the title of this post. In my experience, the problem can almost always be resolved without extra domain add/removes and reboots, which is the most prevalent solution I have
seen around. Usually, this issue is due to a mismatch between attributes of the computer account in Active Directory and those values on the system itself. Here are the steps I take to fix this issue when it crops up:
Open up Active Directory Users & Computers pointed to the domain the computer account resides in
From the “View” pull-down menu, make sure that “Advanced Features” is checked
Navigate to the part of your organizational unit (OU) structure where the computer account for this server resides
Open the Properties for the computer object
Choose the “Attribute Editor” tab on the Properties dialog box
Check the Attributes dNSHostName & servicePrincipalName – anywhere that a fully qualified hostname is specified (e.g. myserver.mydomainname.com), make sure that the entry matches the hostname
you have configured when you go here on your server: Start -> Computer -> Right-Click, Properties -> Change Settings (under “Computer name, domain… settings”) -> Full Computer Name
As an example, for a fictitious W2K8 R2 server whose Full Computer Name is “srv1.mydomainname.com”, these attribute/value pairs should be in Active Directory:
dNSHostName:
srv1.mydomainname.com
servicePrincipalName:
HOST/SRV1
HOST/srv1.mydomainname.com
RestrictedKrbHost/SRV1
RestrictedKrbHost/srv1.mydomainname.com
TERMSRV/SRV1
TERMSRV/srv1.mydomainname.com"
Not reading it carefully I add a computer with the same name as the pc having the issue and followed the above. The problem is that I did not notice that the spn did not want the name of my server (serv1) but the name of the trouble
pc.
dcdiag output
PS C:\Users\administrator.TOM> dcdiag.exe
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
***Error: DC3 is not a Directory Server. Must specify /s:<Directory Server> or /n:<Naming Context> or nothing to
use the local machine.
ERROR: Could not find home server.
PS C:\Users\administrator.TOM> dcdiag.exe /s:DC2
Directory Server Diagnosis
Performing initial setup:
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site\DC2
Starting test: Connectivity
The host 9e0dca7a-d017-445a-b354-adee5ff53d48._msdcs.TOM could not be resolved to an IP address. Check the DN
server, DHCP, server name, etc.
Neither the the server name (DC2.TOM) nor the Guid DNS name (9e0dca7a-d017-445a-b354-adee5ff53d48._msdcs.TOM)
could be resolved by DNS. Check that the server is up and is registered correctly with the DNS server.
Got error while checking LDAP and RPC connectivity. Please check your firewall settings.
......................... DC2 failed test Connectivity
Doing primary tests
Testing server: Default-First-Site\DC2
Skipping all tests, because server DC2 is not responding to directory service requests.
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test CrossRefValidation
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test CrossRefValidation
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Running partition tests on : TOM
Starting test: CheckSDRefDom
......................... TOM passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... TOM passed test CrossRefValidation
Running enterprise tests on : TOM
Starting test: LocatorCheck
......................... TOM passed test LocatorCheck
Starting test: Intersite
......................... TOM passed test Intersite
PS C:\Users\administrator.TOM> regsvr32 schmmgmt.dll
PS C:\Users\administrator.TOM> netdig /fix
netdig : The term 'netdig' is not recognized as the name of a cmdlet, function, script file, or operable program.
Check the spelling of the name, or if a path was included, verify that the path is correct and try again.
At line:1 char:1
+ netdig /fix
+ ~~~~~~
+ CategoryInfo : ObjectNotFound: (netdig:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
PS C:\Users\administrator.TOM> Setup /PrepareSchema
Setup : The term 'Setup' is not recognized as the name of a cmdlet, function, script file, or operable program. Check
the spelling of the name, or if a path was included, verify that the path is correct and try again.
At line:1 char:1
+ Setup /PrepareSchema
+ ~~~~~
+ CategoryInfo : ObjectNotFound: (Setup:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
PS C:\Users\administrator.TOM> netdiag /test
netdiag : The term 'netdiag' is not recognized as the name of a cmdlet, function, script file, or operable program.
Check the spelling of the name, or if a path was included, verify that the path is correct and try again.
At line:1 char:1
+ netdiag /test
+ ~~~~~~~
+ CategoryInfo : ObjectNotFound: (netdiag:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
PS C:\Users\administrator.TOM> nslooup
nslooup : The term 'nslooup' is not recognized as the name of a cmdlet, function, script file, or operable program.
Check the spelling of the name, or if a path was included, verify that the path is correct and try again.
At line:1 char:1
+ nslooup
+ ~~~~~~~
+ CategoryInfo : ObjectNotFound: (nslooup:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
PS C:\Users\administrator.TOM>

Ok fixed.
At a elevated cmd prompt run ;
C:\Users\administrator.TOM>setspn -x
As you can see the DC serv1 had duplicate SPNs.
Checking domain DC=TOM
Processing entry 1
HOST/serv1.TOM is registered on these accounts:
CN=SERV1,OU=Domain Controllers,DC=TOM
CN=C00049,CN=Computers,DC=TOM
{14E52635-0A95-4a5c-BDB1-E0D0C703B6C8}/TOWN-HBWJ29ZOQC is registered on these ac
counts:
CN=Administrator,CN=Users,DC=TOM
CN=TOWN-HBWJ29ZOQC,CN=Computers,DC=TOM
{14E52635-0A95-4a5c-BDB1-E0D0C703B6C8}/town-hbwj29zoqc.TOM is registered on thes
e accounts:
CN=Administrator,CN=Users,DC=TOM
CN=TOWN-HBWJ29ZOQC,CN=Computers,DC=TOM
RestrictedKrbHost/serv1 is registered on these accounts:
CN=C00049,CN=Computers,DC=TOM
CN=SERV1,OU=Domain Controllers,DC=TOM
RestrictedKrbHost/serv1.TOM is registered on these accounts:
CN=C00049,CN=Computers,DC=TOM
CN=SERV1,OU=Domain Controllers,DC=TOM
found 5 groups of duplicate SPNs.
Went to the computers OU and changed computer c00049 to the correct SPN. Now I have a new issues, I'll start a new thread.

SSL VPN message "This (client) machine does not have the web access privilege."

Hello!
I am trying to configure the SSL VPN (WebVPN) and I am almost done but when clicking on the URL's I configured in the bookmarks, I get the message "This (client) machine does not have the web access privilege. Please contact your SSLVPN provider for assistance." I looked through the many tutorials and guides in existence and none talks about such error and the fix for it. In fact, if I search the net for this error message I get only one match, in the Cisco website, where is say that "The client computer does not meet the security criteria of having web access functionality through the SSL VPN gateway." and as fix it gave this tip "Check the URL to the gateway or contact the administrator if it persists." So, nothing on the website about what this issue is and how to fix it. I will provide my IOS configuration and hopefully someone will spot the issue. Here it goes:
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
logging message-counter syslog
no logging buffered
enable secret 5 $1$1LLX$u7aTc8XfNqPZhPVGwEF/J0
enable password xxxxxxxx
aaa new-model
aaa authentication login userAuthen local
aaa authentication login sdm_vpn_xauth_ml_1 local
aaa authorization network groupauthor local
aaa session-id common
crypto pki trustpoint TP-self-signed-1279712955
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1279712955
revocation-check none
rsakeypair TP-self-signed-1279712955
crypto pki certificate chain TP-self-signed-1279712955
certificate self-signed 01
3082023A 308201A3 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31323739 37313239 3535301E 170D3130 30333233 31313030
33375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 32373937
31323935 3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100A8EF 34E3E792 36660498 9801F934 E8A41865 3599EA35 B073AC91 D7A53AF4
A4390D2F CB3DB2DE 936B28F0 A25F3CE1 6F40FD9E E79096F2 F89620E0 B31A7B34
649BBA22 AE44CB55 9F38BF0C 2F2770CF 8380C167 C17D760C 380E28E4 FF7D6874
9EFC310A 2AA60835 F1AA384F CD1A0173 19C98192 EBFBD531 24CB9203 EA9E7D54
B2C30203 010001A3 62306030 0F060355 1D130101 FF040530 030101FF 300D0603
551D1104 06300482 02523130 1F060355 1D230418 30168014 0D9D62EC DA77EAF3
11ABF64D 933633F9 2BA362DC 301D0603 551D0E04 1604140D 9D62ECDA 77EAF311
ABF64D93 3633F92B A362DC30 0D06092A 864886F7 0D010104 05000381 81006853
48ED4E3E 5721C653 D9A2547C 36E4F0CB A6764B29 9AFFD30A 1B382C8C C6FDAA55
265BCF6C 51023F5D 4AF6E177 C76C4560 57DE5259 40DE4254 E79B3E13 ABD0A78D
7E0B623A 0F2D9C01 E72EF37D 5BAB72FF 65A176A1 E3709758 0229A66B 510F9AA2
495CBB4B 2CD721A7 D6F6EB43 65538BE6 B45550D7 A80A4504 E529D092 73CD
   quit
dot11 syslog
ip source-route
ip dhcp excluded-address 192.168.0.1 192.168.0.10
ip dhcp pool myPOOL
   network 192.168.0.0 255.255.255.0
   default-router 192.168.0.1
   dns-server 87.216.1.65 87.216.1.66
ip cef
ip name-server 87.216.1.65
ip name-server 87.216.1.66
ip ddns update method mydyndnsupdate
HTTP
add http://username:[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 1 0 0 0
no ipv6 cef
multilink bundle-name authenticated
vpdn enable
vpdn-group pppoe
request-dialin
protocol pppoe
username cisco privilege 15 password 0 xxxxxxxx
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
crypto isakmp fragmentation
crypto isakmp client configuration group vpnclient
key cisco123
domain selfip.net
pool ippool
acl 110
crypto ipsec transform-set myset esp-3des esp-md5-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map clientmap client authentication list userAuthen
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
archive
log config
hidekeys
interface Loopback0
ip address 10.11.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface Loopback2
description SSL VPN Website IP address
ip address 10.10.10.1 255.255.255.0
interface Loopback1
description SSL DHCP Pool Gateway Address
ip address 192.168.250.1 255.255.255.0
interface FastEthernet0
description $ES_LAN$
ip address 192.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface BRI0
no ip address
encapsulation hdlc
shutdown
interface FastEthernet1
interface FastEthernet2
switchport access vlan 2
interface FastEthernet3
interface FastEthernet4
interface FastEthernet5
interface FastEthernet6
interface FastEthernet7
interface FastEthernet8
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
bundle-enable
dsl operating-mode auto
interface Vlan1
no ip address
interface Dialer1
ip ddns update hostname myserver.selfip.net
ip ddns update mydyndnsupdate host members.dyndns.org
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip policy route-map VPN-Client
dialer pool 1
ppp chap hostname xxx
ppp chap password 0 xxxx
ppp pap sent-username xxx password 0 xxxx
crypto map clientmap
ip local pool ippool 192.168.50.100 192.168.50.200
ip local pool sslvpnpool 192.168.250.2 192.168.250.100
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
ip http authentication local
ip http secure-server
ip nat inside source static tcp 192.168.0.2 21 interface Dialer1 790
ip nat inside source static tcp 192.168.0.15 21 interface Dialer1 789
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.10.10.1 443 interface Dialer1 443
ip nat inside source static tcp 10.10.10.1 80 interface Dialer1 80
access-list 102 deny   ip 192.168.0.0 0.0.0.255 192.168.50.0 0.0.0.255
access-list 102 permit ip 192.168.0.0 0.0.0.255 any
access-list 110 permit ip 192.168.0.0 0.0.0.255 192.168.50.0 0.0.0.255
access-list 144 permit ip 192.168.50.0 0.0.0.255 any
route-map VPN-Client permit 10
match ip address 144
set ip next-hop 10.11.0.2
control-plane
banner motd ^C
================================================================
                UNAUTHORISED ACCESS IS PROHIBITED!!!
=================================================================
^C
line con 0
line aux 0
line vty 0 4
password mypassword
transport input telnet ssh
webvpn gateway MyGateway
ip address 10.10.10.1 port 443
http-redirect port 80
ssl trustpoint TP-self-signed-1279712955
inservice
webvpn install svc flash:/webvpn/svc_1.pkg sequence 1
webvpn install csd flash:/webvpn/sdesktop.pkg
webvpn context SecureMeContext
title "My SSL VPN Service"
secondary-color #C0C0C0
title-color #808080
ssl authenticate verify all
url-list "MyServers"
   heading "My Intranet"
   url-text "Cisco" url-value "http://192.168.0.2"
   url-text "NetGear" url-value "http://192.168.0.3"
login-message "Welcome to My VPN"
policy group MyDefaultPolicy
   url-list "MyServers"
   functions svc-enabled
   svc address-pool "sslvpnpool"
   svc keep-client-installed
default-group-policy MyDefaultPolicy
aaa authentication list userAuthen
gateway MyGateway domain testvpn
max-users 100
csd enable
inservice
end
Thank you!

Hi,
Please check SAP note:
2004579 - You cannot create a FR company from a Package
Thanks & Regards,
Nagarajan

While deploying to another server from RM client using build definition i got below error "Package location does not exist or deployer user does not have access"

We have installed RM client in the POC server .
Installed Deployment Agent in Dev server .
We created Configuration stages for POC->Dev.
We created a template with x copy deployer and selected source as build definition.
While releasing we faced following issue ,
The release was success in POC (Where RM client is installed), but in DEV environment (Which is different server)it got rejected because of the error
"Package location(Path) does not exist or deployer user does not have access"

Hi Dhamayandhi
There is quite a bit to do to get RM working successfully. I have a soup-to-nuts guide on implementing continuous delivery with TFS and RM
here.
Cheers - Graham
Blog:
http://pleasereleaseme.net LinkedIn:

Error : Sales Org.Unit does not have these attributes -- Urgent

Hi, Team,
I am unable to create a service order with serivce material ( Only installation visit charges ) for w/o warranty product .
I am getting error : " Sales Org.Unit does not have these attributes "
I had checked the related Org data of respective sales org , already the sales area combination is also maintained from R/3 with required attributes "
Pls revert with possible solution .
Regards,
VCS

PePe :
Thanks for reversion !!
Basically it is a product Service Material (Servicing Charges), where in I had checked in the transaction , Though the required sales area is well maintained in the R/3 System and is being replicated to the CRM .
When I checked the product Service material , the required comination is missing and could find other sales area combinations .
Pls guide , how to go to get this resolved .
Regards,
VCS

Does anyone have problems occasionally with their slide to unlock on iphone 4s with the ios7 update? And do you think there will be a bug fix? Bit worried

Hi everyone,
I've recently updated my iphone 4s with the ios7 update and there was a bug fix I also downloaded recently but I hadn't noticed anything wrong at the time. I know it's not happened that often today but does anyone have any problems with their 'slide to unlock' button and have to reload their iphone again? Do you think there'll be a bug fix for it? Just worried as it's not old and I have a feeling I shouldn't have bothered with the update at all.

Why would you think it's a bug? If it were a bug EVERYONE would be having the same issue.
Basics from the user guide are restart, reset, restore from backup, restore as new.

I'm getting this error with bootcamp "The startup disk does not have enough space to be partitioned"

Here's the story...
I had a dual boot configuration on my mac with Mac OS X Lion and Windows XP (made with bootcamp).
I decided to reinstall windows.
I deleted the windows partition using BootCamp.
Tried to recreate the Windows partition with Boot Camp and got: "The startup disk does not have enough space to be partitioned You must have at least 10 GB of free space available"
After reading several posts on this forum I decided to defrag the hard drive and try again.
The defrag did not work and I'm still getting the error, I have 22 gb of free space on my drive.
Any suggestions?
Also, I tried repair disk and repair permissions
Hmm, my external harddrive says on the box "OS X 10.5.8 or higher (32-bit kernel only)" Could the 32-bit requirement be an issue? Is lion 64-bit?

Boot Camp must be able to allocate a contiguous block of space on the drive. If it cannot find 10 GBs of contiguous space, then you cannot create the Windows partition.
You will have to backup your OS X partition to an external drive, boot from the external drive, use Disk Utility to repartition and reformat your hard drive back to a single volume, then restore your backup to the internal hard drive.
Get an empty external hard drive and clone your internal drive to the external one.
Boot from the external hard drive.
Erase the internal hard drive.
Restore the external clone to the internal hard drive.
Clone the internal drive to the external drive
Open Disk Utility from the Utilities folder.
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the external backup drive. Source means the internal startup drive.
Restart the computer and after the chime press and hold down the OPTION key until the boot manager appears. Select the icon for the external drive and click on the downward pointing arrow button.
After startup do the following:
Erase internal hard drive
Open Disk Utility in your Utilities folder.
After DU loads select your internal hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed. Do not quit Disk Utility.
Restore the clone to the internal hard drive
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the internal hard drive. Source means the external startup drive.
Note that the Source and Destination drives are swapped for this last procedure.

Hi - I have just bought my first IPAD and I need to transfer from my MAC a 'recipe file' consisting of many, doc and docx files - I have also just bought Keynote to do this but I can't seem to transfer,, does anyone have any suggestions? Thanks

Hi - I have just bought my first IPAD [3 rd gen, no wifi] and one of the things I want it to do is to accept transfered word files
preferably as folders from my MAC - I just bought Keynote but it doesn't seem to work. My files are all doc and docx so I think
perhaps looking into it more I should have bought Pages instead,, but I don't want to spend more money on another app if
possible. Does anyone have any suggestions?

You can download a complete iPad User Guide here: http://manuals.info.apple.com/en/ipad_user_guide.pdf
Also, Good Instructions http://www.tcgeeks.com/how-to-use-ipad-2/
Apple - iPad - Guided Tours
http://www.apple.com/ipad/videos/
Watch the videos see all the amazing iPad apps in action. Learn how to use FaceTime, Mail, Safari, Videos, Maps, iBooks, App Store, and more.
How to - Articles & User Guides & Tutorials
http://www.iphone-mac.com/index.php/Index/howto/id/4/type/select
iPad How-Tos http://ipod.about.com/lr/ipad_how-tos/903396/1/
You can download this guide to your iPad.
iPad User Guide for iOS 5
http://itunes.apple.com/us/book/ipad-user-guide-for-ios-5/id470308101?mt=11
 Cheers, Tom

Hi, my facebook app on my Ipad3 has stopped allowing me to put comments on. Does anyone have any ideas how to correct this? Don't know if it is a problem with the Ipad or just the facebook app. Thanks.

Hi, my facebook app on my Ipad3 has stopped allowing me to put comments on. Does anyone have any ideas how to correct this? Don't know if it is a problem with the Ipad or just the facebook app. Thanks.

Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems
http://tinyurl.com/32drz3d
I saw one post where a user said dust got inside the small microphone hole. Using a vacuum cleaner removed the dust and restored the audio.
 Cheers, Tom

ADF Menu model does not have shortDesc

Hello experts, in my application I need to support 508 compliance. I have implemented ADF menu model and noticed that the menu items does not have shortDesc attribute. In the structure window when I view the menu xml file, I can see accessKey, lable etc. But no shortDesc attribute. Please guide me what should I do. I will have to provide shortDesc for all text items, menu items etc.
thanks

I created ADF menu model from unbounded task flows which will be added to the template using af:navigationPane. The only place where we can add valid label and other attributes for each of the menu option is at menu model meta data file. This is xml file and in structure window, we can change the attributes to each of the menu option. I do not see shortDesc attribute.
Not sure it is a bug in jdev 11.1.1.6
thanks

HT5423 Does Apple have anything official documentation listing compliance with UN38.3, UL 2054, and UL 60950-1?

While it's nice to claim compliance in a Press Release, does Apple have anything official backing this up, like a test certificate, or at lease a Statement of Conformity listing UN38.3, UL 2054, and UL 60950-1? These aren't listed in Apple's "Important Product Information Guide."

Obviously aviation is a special use of the iPad. You come to a forum of regular users with an attitude about Apple and it takes numerous posts before you so much as give us a hint as to your (alleged) real needs. Perhaps if you're really interested in the information, rather than simply trying to make some sort of a point, you would ask United Airlines or American Airlines why they chose the iPad. Naturally, you could also ask the FAA why they gave their approval. In fact, you could always ask Apple, which apparently you never did.
On the other hand, you could simply stay here foolishly trying to make a point about Apple.

Does it have a feature that supports management with accounts, fixed IP, VLAN ?

I'm not quite familiar with those advanced features if it does exist as the fact that i've been primarily using cheap and unknown AP products for years :D I'm planning on upgrading my APs for personal reasons. Could anyone tell me does it have a feature that likely supports management with accounts, fixed IP, VLAN? What is it called and which product could fit my needs?
Thanks.

My name Eric Moyers. I am an Engineer in the Small Business Support Center.
Thank you for the question. Currently all of our Small Business Wireless Access Points support Management accounts, fixed ip's and vlans.
Here is a link for some model comparisons.
http://www.cisco.com/c/en/us/products/wireless/buyers-guide.html
http://www.cisco.com/c/en/us/products/wireless/small-business-100-series-wireless-access-points/models-listing.html
http://www.cisco.com/c/en/us/products/wireless/small-business-300-series-wireless-access-points/models-comparison.html
http://www.cisco.com/c/en/us/products/wireless/small-business-500-series-wireless-access-points/models-comparison.html
If you have any other questions or some specific questions, I am most happy to answer them. You can repost here or if you mouse over my picture you will see my email and can email me directly.
Eric Moyers
.:|:.:|:. CISCO | Cisco Presales Technical Support | Wireless Subject Matter Expert
Please rate helpful Posts and Let others know when your Question has been answered.

Does DW have guides?

Similar Messages

Maybe you are looking for