Does IP Plus support SNA DLSw

I'm not sure which IOS to run on a router. I need IPSec 3DES and DLSw. What IOS do I need for a 3745?
Also, what IOS do I need for a 1720, same requirements?
Thanks

For 3745, IP Plus (i.e. IP PLUS IPSEC 3DES to get DLSw and 3DES) supports DLSw. For 1720, you need IOS with IBM feature (i.e. IP/IPX/AT/IBM/FW PLUS IPSEC 3DES to get 3DES and DLSw) set to support DLSw.

Similar Messages

Does Catalyst 2950 support SNA traffic ?

hello
we are trying to integrate some legacy sna hosts
to switching enviromnent.
we are faced to a strange symptom when legacy hosts
are connected to 2950 switch no traffic sna pass thru
we checked vlan,ports ,STP, but didnt found any hints
removing 2950 from configuration clear out the problem.
so simple diagram
7206 ==wan===7206=ethernet HUB=legacy sna host OK
----DLSW----> -------SNA------>
7206==wab===7206==CAT2950===legacy sna host NO OK
-----DLSW----> ---------SNA----->
are they any issue on 2950 for SNA traffic .
thanks in advance
JYP

Hi,
in general, No. There are no general issues with sna and a cat2950. The switch doesnt care what type of traffic runs through.
Besides the obviouos, the client and the dlsw router
must be in the same vlan.
There are sometimes problems with a switched environment. I.e if you do trunking with dot1q between the switch and the dlsw router and you use the switch in a mode where it tries to autonegotiate the trunk. Dlsw forwards some of the negotiation packets which leaves the switch in a state where the connections dont work.
We have also seen a problem in some situations where a dot1q trunk is used when the switch is configured for PVSTP, per vlan stp. In that case a special type of bpdu's is send which are also get forwarded by dlsw and can cause the switch on the other end to go to blocking ect.
All of those problems can be fixed by either putting a sap filter onto the bridge group on the dlsw router and only allow the sna saps you need or adopt the switch configuration. I.e. turn of autonegotiation of the trunk mode ect.
The issue needs to be looked at individualy and i would advice to open a case with the tac and work on this problem. So that we can understand what the problem is and fix it.
thanks....
Matthias

Does Nokia c5 supports text copy paste feature

Friends i had recently bought a nokia c5 mobile phone and i wants to know that does this phone supports TEXT COPY AND PASTE FEATURE? Its urgent, plz reply. Thanks

Once U have Selected the text keep pressing the # Key and pree the Left Soft Key to Copy The Text...
To past the text in any text editor press and hold the # key and press Right Soft Key...
# key plus Navigation keys also helps in removing the long texts... Just select the text and press C... Its faster than Using Delete Button to remove text..

Does Oracle Tutor support ".xlsm" file format ?

Does Oracle Tutor support ".xlsm" file format ? Where to find the list of supported file formats?
Customer is using Microsoft Office Professional Plus 2010 and EBS R12.1.3.
Thx,
Phil.

Fonzi,
Good, then we are talking about the same thing when it comes to states. The following defines all the digital logic states our hardware supports:
http://zone.ni.com/reference/en-XX/help/370520K-01/hsdio/flogic_states/
A note in that document states the hardware modules that can support all the digital states. The 6541 can still accept the WDT data type, since in your code it did let you. It just doesn't support some of the digital states that it contains. Since it doesn't have hardware compares, it can't handle the compare states. If the WDT only had
You are correct, you must use the WDT when using the extended digital states. Its documented here:
http://zone.ni.com/reference/en-XX/help/370520J-01/hsdio/digitalwaveformdata/
All of my resources have been found in the NI-HSDIO Digital Waveform Generator/Analyzer Help file, which is installed onto your computer with the HSDIO driver. An online version can be found here:
http://zone.ni.com/reference/en-XX/help/370520K-01/
Product Support Engineer
National Instruments

Does iMovie 11 Support Editing AVCHD natively?

Does iMovie 11 support editing AVCHD files natively or conversion to an intermediate codec is needed?

Not to the naked eye.
AVCHD is a highly compressed Group of Pictures format. iMovie does all its rendering at the end when you share the project, so to edit AVCHD natively requires that it would do all rendering plus translate the compressed frames of AVCHD on the fly. This would take a very powerful Mac, so Apple does not offer it.
Final Cut Pro does rendering in the background and does not wait until the project is complete before rendering, so it can edit natively. However, ProRes422 is a very advanced codec, and most people claim that you lose nothing in using ProRes. It also uses 4:2:2 chroma sampling (rather than iMovie Apple Intermediate Codec which uses 4:2:0) which should mean higher color fidelity.
So iMovie = very good.
Final Cut Pro X = Best
For consumer level equipment, (like mine) you probably will not notice.

Does Photo Booth support mirroring via VGA to iPad 2 or iPad Retina?

The company I work for is putting on an event, and we are considering some sort of photo booth for attendees.
We own a few large display monitors, and I was curious if we could use an iPad connected via VGA to the display to mirror Photo Booth as a way to create interest with other attendees at the event.
I think we would have some sort of stand that holds the iPad in place, where attendees can stand in front of it and snap pictures in Photo Booth. As that's happening, all the interaction on the iPad is mirrored to an external display next to the iPad stand.
Does Photo Booth support mirroring? Is this feasible?
Thanks in advance for any information!

Transfer the photo to your computer. Then You can use a USB flash drive & the camera connection kit.
Plug the USB flash drive into your computer & create a new folder titled DCIM. Then put your movie/photo files into the folder. The files must have a filename with exactly 8 characters long (no spaces) plus the file extension (i.e., my-movie.mov; DSCN0164.jpg).
Now plug the flash drive into the iPad using the camera connection kit. Open the Photos app, the movie/photo files should appear & you can import. (You can not export using the camera connection kit.)
Secrets of the iPad Camera Connection Kit
http://howto.cnet.com/8301-11310_39-57401068-285/secrets-of-the-ipad-camera-conn ection-kit/
 Cheers, Tom

Does nike plus work with the ipod shuffle fourth gen?

I already have any iphone but it is too big to run with. I like to listen to music while I run but I like to track how far I run with nike plus. I was looking to get the ipod shuffle fourth gen because its small and can clip on to my clothes while I run and is only $50, but does nike plus work with it?

Hello 5taytrill
The Nike Plus is not supported for iPad. The article below will answer that, plus some others that may come up.
Nike + iPod Frequently Asked Questions (general)
http://support.apple.com/kb/ht1602
What are the system and software requirements of the Nike + iPod Sport Kit?
iPod nano software version 1.2 or later
iPod touch (2nd generation) software version 2.1 or later
iPhone 3GS and later with iOS 3.0 and later
A Windows PC or Mac OS X computer with the latest iTunes
Regards,
-Norm G.

What type of HDD does MS-6382 support?

Hi,
My system has a MS-6382 mobo & I've got to change to the hard drive. I've been looking at ebay & the link below describes a HDD which has "ATA/133 or SATA interface and capacity of 120 GB"
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&category=16178&item=5208766733&rd=1
I don't know much about computers, or even the right questions to ask really, but does the 6382 support 7200rpm drives, ATA/133? What general specs for a HDD should I be looking for?
I would be grateful for any help anyone can give!
Here is some info on my current HDD:
HD Tune: ST380020A Information
Firmware version : 3.39
Serial number : 5GC0KMYD
Capacity : 73.1 GB (~78.5 GB)
Buffer size : 2048 KB
Standard : ATA/ATAPI-6
Supported mode : UDMA Mode 5 (Ultra ATA/100)
Current mode : UDMA Mode 5 (Ultra ATA/100)
S.M.A.R.T : yes
48-bit Address : no
Read Look-Ahead : yes
Write Cache : yes
Host Protected Area : yes
Device Configuration Overlay : yes
Automatic Acoustic Managment : yes
Power Managment : yes
Advanced Power Managment : yes
Power-up in Standby : no
Security Mode : yes
Firmware Upgradable : yes
Partition : 1
Drive letter : C:\
Label : MR01-G4
Capacity : 74822 MB
Usage : 17.54%
Type : FAT32
Bootable : Yes
Jorolat

Quote from: Wonkanoby on 19-June-05, 21:26:02
ata 133 is just a marketing gimick.............only data moves that fast is 2mb in the drives cache
the drive will run at about half that speed once the cache is cleared
dont worry about it
Er, I got another question
I'm now looking at this hitachi model:
http://www.cclonline.com/product-info.asp?id=210&pc=dealtime#
which has good reviews (probably for others in the range). I originally saw it on ebay but it turns out to be cheaper buying it from the above supplier.
The question I have is does the MS 6382 support serial ATA? I'm reasonably sure that the above drive is parallel ATA (ie compatable with the MS 6382) because of the manufacturer's info here:
http://www.hitachigst.com/hdd/support/d7k250/d7k250.htm
but I thought I'ld ask before I order it or in case I change my mind (again).
Thankyou for your help
Jorolat

Does lion server support a single email address across multiple devices??

I am looking to move from an outdated Microsoft Exchange Server 2003 to OS X Lion Server but I am unsure as to how Lion will handle email. I do not want to spend money on a new windows server if I can get a Mac Mini Server to do the job. I am a very small business with a number of email accounts for a couple employees and need access to email and calendar from both the office iMac's and my Macbook Pro when on the road. My IT guy says I need Exchange but he's been off base on a few other items recently and I wanted to check with other sources.
I have 2 new iMac's, a MacBook Pro, an iPad1 and and iPhone4 on the mac side of things and 2 windows computers running XP. I would get rid of the windows computers completely if not for my CAD program which runs best not in a virtual machine mode.
How well will email and calendar entries sync across devices?

I have a very similar setup at my office. Lion Server will push email, calandar, contacts to all of your apple product with out a hitch.
As far the Windows XP machines, you can access email over IMAP with Thunderbird, and calandars via sunbird or the built in web app.
I would ditch the exchange server move to Mac OS X Server, and never look back.
God Luck!
PS. All of your devices will be in sync all the time.
Shore answer:
Does lion server support a single email address across multiple devices??
Yes.

Does Crystal 2011 supports SAP R/3 4.6?

Friends,
I would like to know Does Crystal 2011 supports SAP R/3 4.6? Please help.
Thanks,
Tilak

Hi,
yes, it does. Here is a Screenshot from the CR2011 SPS6 Data Access File
The (4) indicates:
(4) SAP servers required to have at least the above patch levels. The following correction notes should be applied to your SAP BW / SAP NetWeaver BI system: 1125433, 1161911, 1162349, 1162416, 1170323, 1230303 and 1007048. OSS Correction Note 1007048 requires a manual configuration step.
Regards
-Seb.

Camera RAW does NOT yet support raw files for the new Canon Sureshot S95

Camera RAW does NOT yet support raw files for the new
Canon Sureshot S95.
Adobe, please can you provide an update asap

Hello!
I think that you need to be patient.
There has not been any release of Camera Raw since the release of the camera.
I recommend to try the next version once it will be released, as there might be preliminary support (and therefore not listed).
Usually, Adobe is amongs the firsts to support a new camera.
Even though the Camera Raw team is fielded with wonderful coders, I do not think that they do have a time machine to allow support before they have their hands on a camera

OK, as always I waited before downloading a new OS and I sure glad I did. On the APP store I sorted comments by most critical...and WHOA...what is Apple doing? No support for Logic 9, MS Office? Is Apple only trying to reach the iphone/iTouch crowd? HELP!

OK, as always I waited before downloading a new OS and I'm sure glad I did. On the APP store I sorted comments by most critical...and WHOA...what is Apple doing? No support for Logic 9, MS Office? Is Apple only trying to reach the iphone/iTouch crowd? HELP! I was going to buy a new Mac pro & two 27" monitors but until I see some real problem addressing by Apple...I'll keep what I have and see how everything pans out. If anyone has any comments to ally my fears, I welcome them. I've been a devoted Mac user since 1993. 7500; G4; G5; and my latest Mac Pro...Where do I go? Again...HELP!

Hi there,
If you look through ALL the reviews, they are mainly good. I feel that Lion is an excellent upgrade, although not essential.
There have been some issues with MS Office, but right now, it is up to Microsoft to issue a Lion compatible update, which will come in time. Saying this, MS Office has been working fine on my mac, it seems to be an isolated issue.
Logic 9 seems like a strange issue. Again, an update looks to be coming soon, with Lion support.
I do not feel that apple only focusing on the iPhone and iPad user base. There are many features carried along, but the machine can still be used for pro tools and use just as well. It still is a fantastic, reliable, fast, easy to use OS, which I have had very few problems with. Some additions you may not use, but they don't get in the way. You will love the new Exposé, Mission Control, as it is great for pro users who have many windows open at once, and the new spaces. You may however, never use Launchpad, but you don't have to, just drag it away from the dock!
I really reccomend buying a mac with Lion, although if you are worried about bugs, wait a few months for the issues to be ironed out, and updates to be given. Because the update is so very cheap, I really think you can hardly go wrong. Try it out with your current mac, and if you like it, go ahead and buy your new ones.
Lion is fantastic, albeit maybe rushed.
Any other queries, just ask,
Nathan

Does Apple TV support wireless connection to the new MacBook Pro retina in an extended display mode?

Does Apple TV support wireless connection to the MacBook Pro retina display in an extended display mode? What is the output resolution and is sound also transmitted across?

SB1983, by extended display do you mean mirror? All MBP since early 2011 support it if they are running OS X 10.8 Mountain Lion. The resolution will depend on your Apple TV (2 Gen is 720 and 3rd Gen 1080) and wifi, it will lose some quality but I find it minimal. It does also mirror the sound.
Jules

Does AVL table supports popin in WebDynpro ABAP

Hi,
Just a short question, does AVL table supports popin in WebDynpro ABAP?
I know that popin in supported in normal table in WD ABAP. Is this feature also available for ALV table?
Thanks
Yingzhi

Hi Yingzhi Liu,
Did you get any answers to this question?
I'm also trying the same where we need to show additional details for an ALV table row. Is it possible to have a table popin in ALV? We are on 2004s release and implementing Web Dynpro for ABAP.

Does iTunes 11 supports 5.1 Speakers?

Does iTunes 11 supports 5.1 Speakers? If yes which all speakers does it support and how to activate it on iTunes?I am able to play music in 5.1 surround mode using other players such as WMP 11, VLC, GOMP, WINAMP but when I play music using iTunes it only plays in stereo mode i.e. 2.1. The side / rear speakers do not give any output.
Specs:
Windows 7,
Gigabyte FX990-UD3 Motherboard with 7.1 audio on-board support using 6 3.5mm jack pins.
Creative SBS A520 5.1 speaker system.
iTunes 11.1 installed.

I think you mean HandBrake. I use HandBrake and I know exactly what you're talking about. Unfortunately, sometimes HandBrake shows that there is CC available but when you rip it, the CC doesn't appear in iTunes. I notice that but there is no way around it. This only happens with newer releases (I'm positive you only see this issue in newer films). HandBrake needs to be updated to keep up with the newer encryption by DVDs. There is nothing we can do. Hope that this post answered your question.

Does IP Plus support SNA DLSw

Similar Messages

Maybe you are looking for