Does it create a problem if I only connect the backup external drive every few days for use with Time Machine? Should I have purchased Time Capsule instead?
After a near miss with my 4-year old MacBook, I finally wised up and purchased a WD My Passport for Mac to back up my hard drive. I connected the Passport today and have performed the first full backup. However, I do not wish to keep it permanently connected to the laptop. Does this create a problem if I only connect the drive every few days? Should I have purchased Time Capsule instead?
Hello,
I don't think it'll cause a problem, but I'd disable/turn off Time Machine before disconnecting, then turn it back on after you connect it again.
Similar Messages
-
Am I the only one that has safari restart every few minutes when using private browsing?
I have no idea why, but when I use private browsing on safari, it seems to have a mind of it's own once and a while. Randomly, it decides to quit without the "quit unexpectidly" part normally found in this issue, and when I go back onto safari, all of the tabs I had open are no longer there.
Nope, that's all I use is Private browsing on it and it's never behaved this way.
-
Does TM backup external drives?
I have an external 30GB USB2/Firewire drive that I store my work files on. I also have an external USB2 200GB drive that is set up for TM only.
The 30GB external drive does not get backed up when is is connected via Firewire.
Can TM back up an external drive? If so, how?"Open the TM preference pane and click on the Change Disk button. All the drives listed can be backed up by TM unless you put it in the Excluded list (access through the Options button.)"
Drive is visible in the TM prefs pane and is not on the excluded list.
But it is not being backed up by TM.
Going back in TM and the drive is greyed out and not selectable.
How do I get it on the back up list?
What I think I noticed was that when this drive was connected as a USB2, it was backed up. However, now that I am using the Firewire connection it is not. -
HT3529 Is there a way to create, store and use preset messages for use with "Messages"?
Is there a way to create, store and use preset messages for use with "Messages". I often have a recurrinig message to send, after a repeating event, and need to enter the same short message each time. It would be nice to have this short message stored and selectable so that I do not need to enter each time.
found an answer that seems to work:
https://discussions.apple.com/message/17997300#17997300 -
I see that Adobe still hasn't fixed this issue where Lightroom freezes up during import when a system has multiple external drives attached. Disappointing.
A friend suggested that I configure Lightroom to only recognize the single external drive where I save my RAW files. I haven't been able to find out where in Lightroom's settings to do this.
Currently the only folders I have in Lightroom are my local C disk and my external drive with the RAW files, (K), where I do all my editing.
Can anyone offer advice on how I can either do what my friend suggested or find another way of dealing with/solving this issue? Currently Lightroom is almost unusable for me since I cannot add new files on my K drive to develop.
Thanks.I save edited images from Photoshop into a new folder on the same hard drive my catalog is on, then attempt to import, or to right-click on the edited image and choose Open in Lightroom. Lightroom hangs in either situation.
-
How does one install non-English character sets for use with the "find" function in Acrabat Pro 11?
I have pdf files in European languages and want to be able to enter non-English characters in the "find" function. How does one install other character sets for use with Acrobat Pro XI?
Have you tried applying the update by going to Help>Updates within Photoshop Lightroom? The update should be using the same licensing? Did you perhaps customize the installation location? Finally which operating system are you using?
-
my host name changes every few days, since Xmas adding a macbook its changed 6 times. Do I need to stop this? Does it cause problems with sharing between the iMac and macbook?
There are several possible causes for this problem.
1. Two (or more) computers on the local network have the same Bonjour name, such as "X's-MacBook-Pro.local".
2. You have two simultaneous connections to the same local network: probably Ethernet and Wi-Fi. If applicable, disconnect the Ethernet cable or turn off Wi-Fi.
3. A Mac wakes from sleep due to network traffic. This is due to a bug in OS X that may only affect some models.
4. A device that gets its network address from the router wakes from sleep, and the address it was using before has been assigned to another device.
5. A third-party wireless router has incompatible settings or firmware. In that case, refer to the manufacturer or ISP for support. Restarting the router may help, temporarily.
6. See also this support article.
Rename the computer in the Sharing preference pane. -
This is not correct solution. I have fresh/new copy of Windows 7 64 bit and I have the same problem.
Autorun only shows the Apple Bonjour service. It started when try to sync more than one iphone over WiFi. I have two iphones and an iPad. I turned off syncing over WiFi and still has high CPU utilization. One of the CPU's is pegged at 100%. It is the AppleMobileDeviceService.exe process.For the record, I then followed the suggestion of MarcDCMB in https://discussions.apple.com/thread/4291206 of just manually restarting the Apple Mobile Device service in Windows services.msc once each time after starting iTunes and the service no longer hogs CPU after that service restart. Not too painful as a work-around, and apparently an effective one, but clearly not a solution to the problem. Again, as above, all the other solutions didn't work for me and I have no conflicting software as far as I can tell. So you'd have to say this Apple's problem.
Also FTR, I am still on the 5.2.0.6 version of the Apple Mobile Device Support MSI and I don't know if that is relevant to this work-around working but my sense is that it is NOT relevant. I'll report back on this thread if I re-upgrade and the problem returns in spite of the service-restart approach. -
I want to upgrade the IOS of my Cisco 2821 from Version 12.4(11) to v 15.1 (XB), but I have CCME v 4.2 (0), is there any problem if I only upgrade the IOS and leave the CCME as it ?
ThanksCME is part of the IOS, so you can't upgrade the IOS seperately from CME.
That said, if this is a production environment you should proceed with caution and be prepared to roll back as you may find bugs, etc.
You should also look at release notes and make sure your phone firmware will still work or needs to be upgraded too.
Brandon -
I have created a PDF with mp3 audio clips, the file works on PC's with audio playback (WIndows 7, 8 ) however the audio does not play when hosted on a website or an ipad/tablet computer or smart phone when used with PDF reader
adobe42135678 wrote:
the audio does not play when hosted on a website...
When viewing in what browser? -
I own a iPhone 2G Today
He underwent updated Software
He gave me this message
"The SIM card inserted in this iPhone does not appear to be supported.
Only compatible SIM cards from a supported Carrier may be used to activate iPhone. Please insert the SIM card that came with your iPhone or visit a supported Carrier's store to receive a replacement SIM card.
I did not know what to do??Follow this article: iPhone: Troubleshooting No Service or No SIM
Symptoms
In certain situations, iPhone may present one of the following symptoms:
"Invalid SIM" or "No SIM Card installed" alert appears intermittently.
Status bar displays "No SIM" when a SIM card is installed.
Resolution
If you encounter any of the above symptoms on your iPhone, try these steps to attempt to resolve the issue:
Update your iPhone to the latest version of iOS.
Toggle Airplane mode On and Off.
Try turning iPhone off and then on again.
Check for a carrier settings update. Tap Settings > General > About. If an update is available, a prompt will appear.
Remove the SIM Card and verify that it is a valid, carrier-manufactured SIM. Also verify that it is not damaged, worn, or modified. Then reinsert it.
Restore the iPhone.
If you still are unable to resolve this issue, contact Apple support for further assistance. -
When you open iTunes this message appears. The sim card inserted in this iPhone does not Appear to be supported. Only compatible SIM cards from a supported Carrier may bre used to activate iPhone. Please insert the SIM card That came with your iPhone or visit a supported Carrier's store to receive a replacement sim card.
dear sir.
where i get this replacement sim card.i live in bangladesh.not have support carrier in my coutry..
so how get..please help me.. -
The SIM card inserted in this iPhone does not appear to be supported.
Only compatible SIM cards from a supported Carrier may be used to activate iPhone. Please insert the SIM card that came with your iPhone or visit a supported Carrier's store to receive a replacement SIM card.I got the same message.
I bought an iPhone 5 at full retail price from an AT&T store. I requested the phone to be unlocked through their unlock portal. The AT&T unlock system asked for the IMEI number, a copy of my receipt showing that I bougth the phone at "No Commitment" price. A few hours later I received a message from AT&T stating that the unlock request was approved. I then followed the instructions to back up the phone and restore it through Itunes. The phone activates normally with the AT&T SIM card. But when I insert my VODAFONE SIM I get the massage "THE SIM CARD... etc.
I tried again to back up & restore the phone 3 or 4 times, no success. I have also allowed 24 hours for the unlock process to complete. Still no luck.
I have checked again on the AT&T Unlock Status portal and it shows "Unlock approved".
Where is the issue here? Do I have to call Apple or return the phone to AT&T and get the unlocked phone through the Apple Store?
Thanks for any help on this. -
The SIM card inserted in this iPhone does
not appear to be supported.
Only compatible SIM cards from a supported Carrier may be used
to activate iPhone. Please insert the SIM card that came with your
iPhone or visit a supported Carrier's store to receive a
replacement SIM card.It appears that you have an iPhone that is locked to a carrier other than the one you were using. Now that you have tried to update the iOS, it has relocked. That is what happens if you are using a phone that has been hacked to unlock. You have also forfeited support from Apple and from this forum.
-
my iphone 5 is problem facing like that. when i switch off my iphone5 then plugh for charge with data cable or charger adapder or only data cable with no power connect phone is starting why? means on my phone Why? any one can explane this matter please. switched off my phone but on without power button . what is the problem?
Thanks
s.m slimall iphone is same like that
Maybe you are looking for
-
Error while calling utl_dbws.create_service
hi, i get following error "ORA-29541: class SYS.oracle/jpub/runtime/dbws/DbwsProxy could not be resolved" while calling a webservice from utl_dbws.create_service Can any on help me. kiran
-
How to get the number of hits ("returned rows") in read table statement
Hi Experts I have the statement shown below, which seems not to work as I would like it to. My problem is that I would like to do two different things depending on weather or not a read table statement results in 0 hits or 1 (or more) hits. READ
-
How to select Multiple files in ADF?
I have a requirement to select multiple files in my aaplication. I know af:inputfile can select only one file and putting more af:inputfile component on the screen is not an option. Can someone please help me on this Thanks RJ
-
Item in FRF is paid in EUR due to expiring currency
Hi Expert, Our client has got error after F110 run for custome in Production due to which he is unable to generate Payment advice. Please find below Error in F110 after Paymen run done "Item 16039805 in FRF is paid in EUR due to expiring currency". C
-
Consolidating libraries on my two macs
I have one iTunes account, but I purchase music from both my macs, thus I have different songs in my "purchased music" folders. I have two questions: 1) Is there a way to sync my computers so they both reflect all my purchases in the "purchased folde