Does it do any good to use a "N" router with a "G" computer

I need a little more range not speed. I see extended range "G" routers but they cost as much as an "N router. I would continue to use a standard "G" internal card in the computer.

Sorry, but in most cases, you will need to wire your WAP to your primary router.
The only combination of router and WAP (that will work wirelessly) that I know of, where the WAP can be setup as a "wireless repeater", is the combination using a WRT54G and a WAP54G. Note that when the WAP54G is used as a wireless repeater, your wireless connection speed is cut in half to 27 Mbps, and your maximum data throughput is cut in half to about 1.0 to 1.5 Megabytes per second. This is because the 54 Mbps wireless g connection is being shared between receiving data and transmitting data.
Because of these limitations, most users prefer wiring their WAP to their primary router, as this will give them their full wireless g bandwidth.

Similar Messages

Hi Guys! I have an Imac with Mac OS X version 10.5.8 and bought a wireless keyboard. Unfortunately I can´t use the volume buttons on the keyboard. I have checked almost everything, does anyone have any good idea?

Hi Guys! I have an Imac with Mac OS X version 10.5.8 and bought a wireless keyboard. Unfortunately I can´t use the volume buttons on the keyboard. I have checked almost everything, does anyone have any good idea?

Hello, try kguy's solution here...
https://discussions.apple.com/thread/2332457?start=0&tstart=0
First, Go to System Preferences, keyboard, and click on the Keyboard tab
Make sure that the checkbox by "Use all F1, F2, etc, keys as standard function keys" is NOT checked.
Next, click on the Show All button, and select Bluetooth. You should see your Apple Wireless Keyboard listed on the left side of the screen.
Click once to select it, and then click the gear icon at the bottom of the box, and choose Disconnect.
Power off the keyboard by holding down the power button on the keyboard for a few seconds until it show "keyboard Off on your imac screen, then turn it back on again.
The device should appear once again in your bluetooth list.
Try out the volume control buttons now, and see if that cleared things up

Does Apple have any good way of managing iPhones for business?

I finally broke down and allowed iPhones into our company when Apple introduced the ability to provision phones like phones (e.g. don't have to teather them to a computer to set up). This and the "business" management tools opened the door, so we got about 30 of them.
WHAT A HUGE MISTAKE!!!!
Apple is now going backward. When a phone comes into our shop, we have to load up iTunes and get the phone to sync before we can do simple things like wipe the phone or troubleshoot "why did my bluetooth quit working". All of their "enterprise focus" seems to be around security and app control, with nothing I've seen for the day-to-day keeping things running. (Not saying app control and secuirty are unimportant, just not enough).
Does Apple have any good business management tools that I'm missing? I know about MDM, but too much setup for a relatively small number of phones. Besides, my understanding is the MDM only does app management / security policy. Right now we use Apple's stand-alone configurator. Fine for pushing policy and apps, but useless for troubleshooting and day-to-day management (like resetting a phone back to factory configs).
Also, is my carrior correct that Apple will not allow them to replace phones that have gone bad under warranty? They told me for the iPhones we have to physically take them to an Apple store for troubleshooting / replacement even after 100% identifying the issue! That is an hour (at least) wasted to send one of my folks to the store. I know we don't just have a bad carrior, becaue they happily send out replacement on other brands after troubleshooting over the phone.
I actually do like the overall look/feel of the iPhones. But unless Apple becomes much more corporate-friendly, I can only recommend that companies refuse to purchase any iDevice. BYOD, sure...but when you buy tens or hundreds of phones stick to Android, Blackberry, or even (sorry) Microsoft based devices.

Does not seem to work that way for us. We plug the phone in, and the first thing iTunes does is say the phone needs to be "authorized for this computer". It also states that the phone can only be authorized for x computers.
It then goes through it's jig while we wait, and finally comes up with the phone. Only then can we try to wipe / update the phone. We do stop the sync process, that automatically starts wanting to run. Maybe has to do with a version difference between what you use and what we use. I did notice that an older version of iTunes seemed a bit friendlier, but would not support our iPads.
However, when we were troubleshooting the bug where wireless / bluetooth quits working it was quite a bit more difficult than this for a phone a user handed us. Troubleshooting steps required that the phone be "restored" in iTunes. However, iTunes insisted on our providing a password that neither we nor the user knew. Maybe just learning curve, but it took about an hour before we were able to get that phone to a point where we could reset it.
Here is a sincere question for you, since you say you support a fleet of phones. Do you really NOT get annoyed when your tech has to take a iPhone to a computer with iTunes, plug it in, and work from there whenever there is a user issue that needs to have the phone wiped back to factory standard? This compared to being able to punch a few buttons on a different phone, right there in the users office, then hand it back to the user and say "your are fixed".
My only assumptions are that IT staff want to solve issues as quickly and efficiently as possible. Requireing a tech to deal with iTunes for simple procedures is not, IMHO, "as quick and efficient as possible".

Apple iMac 24" 2008 , will this imac be any good for using xcode ? Thanks

Apple iMac 24" 2008 , will this imac be any good for using xcode ? Thanks

Hmmmm.
http://www.nvidiadefect.com/apple-2008-imac-24-with-nvidia-geforce-8800-gs-t2243 .html

Hey guys, im in need of seriously help. i let a friend jailbreak my iphone and now its jus stuck at the apple screen. i tried rebooting it and everything but nothin is working. does anyone have any good advice?

hey guys, im in need of seriously help. i let a friend jailbreak my iphone and now its jus stuck at the apple screen. i tried rebooting it and everything but nothin is working. does anyone have any good advice?

put the phone in DFU mode (do a search for how to do this) and restore to the latest firmware. you may have to download the firmware from apple and when selecting restore or update in itunes press the shift key and select the firmware.
Hope this helps

Does JCE 1.2.2 make use of a certificate with an expiration date?

Does JCE 1.2.2 make use of a certificate with an expiration
date?
If so, what's the date?

The validation code which checked for certificate expiration was only found in JCE 1.2.1. It WAS REMOVED from JCE 1.2.2 and all successive releases like JCE in JDK 1.4.x and 5.x (and soon in 6.x). This expiration problem was the primary reason for releasing JCE 1.2.2 over three years ago. Export control regulations changed following the release of JCE 1.2.1, and Sun released 1.2.2 shortly thereafter so that customers wouldn't have this expiration problem.
This change is documented as the first bullet in the change log for JCE 1.2.2, which is found both in the product distribution itself and on the following JCE product page:
http://java.sun.com/products/jce/jce122_changes.html
That said, JCE 1.2.2 is indeed signed with a certificate which is valid until October 2006, HOWEVER the JCE 1.2.2 and JCE in JDK 1.4.x/5.x code no longer checks that expiration date. All it cares about is that the code signature is valid.
My understanding is that BOTH JDK 1.3.x and JCE 1.2.2 are slated for End-of-Life on March 30th, 2006, and will no longer be supported by Sun. Both should continue to work after that time, but will no longer be supported.
I hope that helps clear the confusion.

My ipod nano gen 4 is stolen! He is my first love with ipod. Can I lock this device by use serial number of the device? I don't want any bad guys use or do anything with my love one. Please let me know if have the way to do thanks.

My ipod nano gen 4 is stolen! He is my first love with ipod. Can I lock this device by use serial number of the device? I don't want any bad guys use or do anything with my love one. Please let me know if have the way to do thanks.

zenith_nm wrote:
My ipod nano gen 4 is stolen! He is my first love with ipod. Can I lock this device by use serial number of the device? I don't want any bad guys use or do anything with my love one. Please let me know if have the way to do thanks.
Nope!
http://support.apple.com/kb/HT2526 How to report lost or stolen Apple product

How To Use Your Own Router with Out Loosing Verizon's FIOS Services

How to use your own router with Verizon’s FIOS Service
First, you need a basic understanding of how FIOS works but unfortunately there are two types of FIOS systems out there. All of the systems utilize a fiber optic cable to bring TV, phone and internet to your location over one optic cable. In addition these systems provide interactivity including widgets, remote DVR, movies on demand and so forth via an IP (Internet Protocol) signal. Your STB (Set Tip Box) requires both a video and IP signal. The IP signal is necessary for all of the aforementioned interactivity. The fiber cable terminates at the Optical Network Terminal or ONT for short. The ONT converts the optics into a digital signal that can be utilized by ones equipment. From the ONT your video, phone and internet are provided to the location. This is where things can differ as the internet signal can be provided via a coaxial (MoCA or Multimedia over Coax Alliance) or RJ45 Cat5 (Ethernet) cable. It is important to identify and understand the differences of these two setups. In my case I have my internet entering via Ethernet cable, which in my humble opinion makes things a heck of a lot easier.
How does one tell the difference? In most cases it’s rather simple; just look at the Verizon’s router WAN (Wide Area Network) Port. Does it have a RJ45 (Ethernet) or Coax (TV cable Cord) going to it? If the router’s WAN port doesn’t have a coaxial connector then one will need to convert the MoCA signal into a usable Ethernet signal that routers understand. The easiest way is to use Verizon’s router as a bridge. In this method the Verizon’s router simply converts the signal and passes it along to your own router. The challenge is to try to maintain the interactivity that FIOS TV provides. Because of this one needs to supply the IP routed signal back to the FIOS router. There are multiple methods for doing this and I would recommend investigates which one make the most sense.
In my particular case the IP signal was provided by Ethernet. Again there are various ways of installing one’s own router. The hardest is to utilize Verizon’s router as a bridge. This setup requires configuring Verizon’s router as a bridge and also creating a VLAN (Virtual Local Area Networks). In addition one needs to set up their own router so it will work with the various routing tables and networks. For me this is too complex for the average person and it can be difficult to trouble shoot if something goes wrong. Please consider that Verizon will not support utilizing third party routers.
The easier method is to request an Ethernet signal (if you don’t already have one) from their ONT. I would highly recommend getting your hands on a NIM or Network Interface Module. This device is used to convert Ethernet to Coaxial so it can be fed back to your STBs. These can be purchased online and Verizon technicians can be a valuable resource with these sorts of acquisition. At the very least they can point you to the right direction. Once you have a NIM the rest is rather simple.
Log into the current Verizon Router.
Located the router’s MAC address and copy it down.
Go to the port forwarding section and copy down the Applied Rules.
Example:
Network Computer/Device: 192.168.1.100:63145
Application & Ports Forward: Application UDP Any -> 6347
Note: There may be up to three entries for each one of your Set Top Boxes.
Look at your current device list, typically found on the home screen. Copy down your STB MAC and IP address.
Example:
IP-STB1
Connection Type: Ethernet
* IP Address: 192.168.1.100
IP Address Allocation: DHCP
*MAC Address:                07:73:fFe:ad:8b:3f
* Things you will need to write down
Go to the network section and look for the main Ethernet connection. Select this and then select more setting, typically found at the bottom. Release the current lease.
Remove the Verizon router
Install your router
Connect the NIM by plugging in an Ethernet from one of the routers LAN (Local Area Network) ports to your NIM. Then connect the coax cable, the same cable that was used by Verizon router.
Set you DHCP routing IP pool to accommodate Verizon’s STB IP’s (note their IP’s start at 192.168.1.100)
Go to DHCP section and reserve the STB IP’s by inserting the IP’s and MAC addresses. This shall ensure that nothing else utilizes the same IPs as the STBs thereby preventing IP address conflict.
Add the port forwards from Step 5 above.
Clone Verizon’s Mac Address utilizing the info from step 2
Finish setting up the router in typical fashion.
Unplug and re-plugin your STB’s and test functionality. It’s best to try using a widget or Movie on demand function.
Note: if the new router can net get an internet signal contact Verizon’s support and have them release the IP and reset the ONT.
EVERYTHING should be working at this point.

3 Go to the port forwarding section and copy down the Applied Rules.
Example:
Network Computer/Device: 192.168.1.100:63145
Application & Ports Forward: Application UDP Any -> 6347
Note: There may be up to three entries for each one of your Set Top Boxes.G
Your display obviously is not like mine as mine does not dosplay the port associated with the ip address
whatever, the STB's start at 192.168.1.100 and icement by 1 for each
the port addr's will be 63145 alo incrementing by 1
there is 1 entry for each in my pf list
however each ip addr also has a port entry starting at 35000 also incrementing by 1 for each ip addr
For some unknow reason these are duplicated e.g I appear to have 11 entries exaactly the same for each stb and as the fios services rules have no action switc there is nowhere to delete the extraneous garbage.
Why do you clone the mac addr??

Can I use the airport express with a desktop computer that is not wire less- I want to have wifi in the house for an iphone

Can i use the airport express with a desktop computer not wifi- I want wifi for my iphone

I can't seem to find any information anywhere. It seems like it should work since the AX is showing up on his wifi settings on both his iPhone and iPod. Not to mention the Apple "Genius" told him that it should work. However, they also told him that it came with an ethernet, USB and the stereo patch cables...

HT4199 I have a new iPhone 4s. I have a home wi-fi network using Cisco Linksys2000 router with all settings per this article - phone will not see network if set to 5 GHz channel width - solution?? 2.4 works but is not optimal with other devices in home

I have a new iPhone 4s. I have a home wi-fi network using Cisco Linksys2000 router with all settings per this article - phone will not see network if set to 5 GHz channel width - solution?? 2.4 works but is not optimal with other devices in home (computers; tivo). Have others seen this? Any advice is much appreciated.

Stephen Spark is right - your best alternative is to use a simultaneous dual band wireless router like the AirPort Extreme. Your Cisco Linksys2000 is not a dual band router, meaning that it will be constrained to operate at the slowest speed of all the devices on your network.
The AirPort Extreme's dual networks will support all your 802.11n devices as well as all your 802.11b/g devices on both the 2.4 and 5 GHz frequencies simultaneously.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

Currently using Photoshop CS5, but with a replacement computer and upgrade to Yosemite, keep being told I need to install the legacy Java 6. Currently, Photoshop won't even open. I absolutely do not want to subscribe, don't want to mess with the cloud, ju

Currently using Photoshop CS5, but with a replacement computer and upgrade to Yosemite, keep being told I need to install the legacy Java 6. Currently, Photoshop won't even open. I absolutely do not want to subscribe, don't want to mess with the cloud, just want to buy an upgrade to something that will run for a while longer. I don't care about Lightroom, Bridge, Illustrator, etc.; most of those I've deleted over the years. But I do use Photoshop - or would if it would still run. What options do I have?

This is the java you need for photoshop cs5 to work on mac os x 10.10 Yosemite
https://support.apple.com/kb/DL1572?locale=en_US
It's also possible you may have to reinstall photoshop cs5 even after installing the above java, because sometimes the upgrade to mac os x 10.10 messes up the photoshop cs5 installation.
You can download photoshop cs5 from here if you don't already have the install media.
https://helpx.adobe.com/creative-suite/kb/cs5-product-downloads.html

Does anyone know any good free games or apps?

im loooking for some free games which are good i like action games so if anyone knows any good games please tell me

It all really depends upon what you want. Since you are asking for free games, just download them and try. It does not cost anything.

Is there any way to use Adobe Extension Builder with After Effects?

I have been using Script UI and Javascript within the ExtendScript Toolkit to build panels for After Effects CC, but I like the way the Adobe Extension Builder works with Eclipse, and the power of including external libraries like JQuery. Is there any route to build extensions for After Effects with this or some similar solution?

Hi Hallgrimur,
I was checking the documentation for CC14 Extension SDK and found that the HTML5 extension development is available now for After Effects too. I could not find any update of Extension Builder though which would support the After Effects extension development. While searching I came across this thread, so was wondering if you might have any update on how to go about with the HTML5 extension development for After Effects. Thanks a lot in advance.

I need to know if any body is using this hard disk with leoardandtimemachin

Hi i need to know if any body has tried to use this hard drive with time machine and leopard and if any body has have any problems using it with these applications the external hard drive is:
Lacie brick lego hard drive, usb 2 high speed, 7500rmp refrence, 301150U from 2006 thanks

I am not using that drive, but I would recommend a FireWire drive (FireWire 800 if available), for better speed and reliability.

Does it do any good to use a "N" router with a "G" computer

Similar Messages

Maybe you are looking for