Does k8n neo4/sli platinum support creative 6.1 surround speakers?

I own an MSI k8n neo4/sli platinum mother board with an on-board SB live 24-bit sound chip. I have confirmed that the retail version of the sound blaster live 24-bit pci sound card will support a 6.1 speaker set up (specifically creative labs megaworks 650) with creative labs proprietary plug configuration of having front center, sub, and rear center speakers all on the same (orange) plug. The plug configuration on the back of the k8n neo4/sli platinum is color coded the same as the retail version of the sound blaster live 24-bit sound card. what I need to know is... Does the k8n neo4/sli platinum support a 6.1 surround sound speaker configuration? I can find no documentation in the literature confirming or denying this. FWIW... the creative sound card softwear that came with this motherboard will allow me to configure and test for 6.1 speakers... but I get no sound from my rear center speaker. On testing, the 5.1 speaker configuration works as it should but I am unable to test for 7.1 config as I lack a 7.1 speaker setup. I am using Version 5.12.1.356 of the creative drivers downloaded from the MSI driver support.
Thanks for your time.
Malpighi44
 

Update...
 Last night I noticed that, in windows sounds and audio devices_advanced speaker settings, there is no 6.1 speaker configuration option. (GO to: control panel \sounds and audio devices \sounds and audio devices properties \ volume \speaker settings advanced \advanced audio properties \speakers \speaker setup pull down menu).
 I don't know if this pull down menu is generated by windows XP auto detection or the MSI/Creative drivers and .inf files that are installed for the SB 24-bit chip, but it leads me to believe that this MB does _not_ support 6.1 sound.
 Can anyone else confirm that this 6.1 speaker option is present or missing in windows with:
1) This MB
2) Windows XP in general
or 3) if it is available to those that have an audigy or 6.1 compatible sound card
Once again...
Thanks for your time,
Malpighi44
My system:
ANTEC SLK3000B ATX CASE
ATHLON 64 3800+ NEWCASTLE
MSI K8N NEO4 PLATINUM SLI
OCZ PREMIER DDR PC3200 2X512MB
2-MAXTOR MAXLINE III 250GB
POWERCOLOR RADEON X800XL PCI-E 256MB VIVO
ENERMAX EG495P-VE NOISETAKER 485W PS
LITEON SOHW-1673S 16X8X16 DVD+RW
LITEON SOHD-16T9S 16X DVD-ROM
1.44MB 3.5IN FLOPPY
WINDOWS XP PRO service pack 2

Similar Messages

  • Confused - whats the difference between K8N Neo4 SLI Platinum and Diamond??

    MSI web page says the Diamond has:
    "Silicon Image's SATA RAID supports another 2 SATA II ports. Transfer rate is up to 300MB/s."
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=638
    their Platinum page doesn't list the Silicone Image raid as a feature on the Platinum.
    I have K8N Neo4/SLI Platinum and it has the Silicone Image raid - I'm using it now. 
    Can anyone explain this? 
    Another question:  for both boards it shows:  "NV RAID (Software) - - RAID function available for ATA133 + SATA HD drives or 2 SATA HD"   
    How can the Raid fuction work for ATA133 drives since the cables for SATA and PATA are different?   What do the mean Raid for 133?
    Thanks!!!
    Tony

    https://forum-en.msi.com/index.php?board=36.0
    d/l a raid manual and all should be clear

  • MSI K8N Neo4 SLI Platinum / HDD_LED Problem

    Hello,
    First off I would like to say that MSI boards rock! I've always been happy with them, in fact this is my fourth MSI board. The board is K8N Neo4 SLI Platinum.
    Unfortunately, I'm having a problem with this one. The problem is minor, but it shouldn't happen, at least I don't think. The problem is that even though the hard drive activity wire is properly connected to HDD_LED, it is not working with my SATA drive. No light at all!
    I read in newsgroups that there are people with this same problem (although not necessarily with this same board). I haven't found a solution to this yet. So my inquiry here is:
    1. Is there anyone else with this exact board with a SATA drive that can confirm his/her HDD_LED light is also not working with a SATA drive?
    2. Does MSI have a fix/solution for this?
    Thank you.

    Quote from: Jesteronyer6 on 23-July-05, 08:10:26
    THere is a positive and negative side on those pins have you tried flipping it over?
    This has got to be one of the biggest "pains in the a&&" in setting up a new mobo and connecting it to a new case...

  • NOT Stable overclock on K8N Neo4 SLI Platinum 3.9 MOD + Venice 3000+

    Hi, to all the people that make this forum so usefull. 
    I´m wondering what i´m doing wrong? ??? ??? ???
    I have a Venice 3000+ E3 on a K8N Neo4 SLI Platinum and 1 Gb OCZ Rev2, TCCD.
    I have overclocked the CPU to 9 x 290 Mhz (2610Mhz) HTT 3X, MEM 1:1 290Mhz 2.5-4-3-10 1T 2.75V.
    Memory is ok at this setting on MEMTEST v1.65.
    I have tried Every VCORE possible to the CPU and Nforce Chipset and can´t make it stable.
    I can work on windows with this settings but some times the computer locks. >:(
    If any of you in the forum have a suggestion or recomendation, please Let me Know.
    For a list of complete hardware of my rig, look at the signature.
    Thank for all.
     

    I had this exact same problem, same RAM, same MOBO, with an X2 3800+.
    For some reason it wouldnt overclock 1:1, and that RAM at wouldnt run at 2.5-x-x-x-1T timings (and i dont think it did 2T stable for too long either). So i was limited to either 2 or 3.
    So right now I'm running my X2 at 2.55ghz and my OCZ Platinum 1gb TCCD @ 232(2-3-3-6-1T). Done so by using 183 divider at 255fsb. HTTmulti=3x
    Does dual prime 95 for 10-12 hours (havnt tried for longer)
    Oh also, for voltage, the RAM has 2.80-2.85, and NF4 gets 1.55-1.60v.

  • Bios Settings For MSI K8N Neo4/SLI Platinum MB

    Hello all...  Has anyone came up with the best and most stable bios settings for the MSI K8N Neo4/SLI Platinum motherboard yet.  Specifically under the CPU and Memory menus. 
    If anyone has seen any, please post them. or post a link.
    Thanks
    DaaDoctor

    Well that depends on the installed CPU and memory, doesnt it? So I find that question kinda odd.
    One thing though: Dont use Cool n Quiet. 

  • MSI K8N NEO4 SLI PLATINUM Northbrigde fan faulty

    Hi, i have an MSI K8N NEO4 SLI PLATINUM mobo since it was released till now the northbridge fan gone faulty. It spin slow as if something causing it from spinning. Worst of all it makes a LOUD vacuum noise 'voooooooooooommm'. Anyway to fix this or to get it replaced? I still have warrenty for it. Thanks
    leon,
    London, United Kingdom

    Then there is a post here in the forum where some guys are talking about the replacement of that hsf and I think they did find one of some brand that I do not recall at the moment, but search here and you will find it...
    Be well....

  • K8N Neo4 SLI Platinum and Dual Core

    I just received my new MSI K8N Neo4 LSI Platinum motherboard and I am waiting on my new processor AMD Athalon64 dual core 4400+. My questions are:
    1. If the bios on the motherboard is not the latest one will the motherboard boot with the dual core processor. If not what are my options?
    2. If I manage to boot, and all the components are new, assuming I will boot into DOS, can I make a bios update from there or I need to install Windows and then do a bios update?
    3. And what are the bios update procedures for MSI motherboards?
    Thanks a lot guys for help

    Quote from: Dream_true on 30-June-05, 14:02:02
    hi,
    In order to use dual core CPU on the MB, update BIOS to the latest version (3.4 and above) before using it. After flashing BIOS, please enter BIOS Load Optimized defaults, Save&exit it, then change CPU to dual core one.
    For how to update BIOS, refer to:
    http://www.msi.com.tw/html/support/bios/note/award.htm
    You can use the dual core without updating the Bios. However, your second core won't work until the update. So you can use the cpu without the correct bios version to install windows.

  • Vista Sound problems with K8N Neo4 SLI Platinum

    I wonder if anyone have gotten the sound to work under 32-Bit Vista RC1 (build 5600) on the K8N Neo4 Platinum SLI (MS-7100)? Installation of the, by MSI, provided XP driver (Creative_audio_32-64bit.zip) seam to work, and the device looks installed in Device Manager, but still no sound... Also, the icon for volume control in the icon trey detects that there is no sound card installed.
    Anyone with a similar problem? Any solutions? Suggestions?
    Thanks in advance!
    Br
    Daniel

    Thanks!
    I did try one of these drivers before without success. Now when I tried the old driver from nov 2005 it worked!
    Drivers are found here:
    (http://se.europe.creative.com/support/downloads/download.asp?MainCategory=1&nRegionFK=&nCountryFK=&nLanguageFK=&sOSName=Windows+Vista+32-bit&region=3&Product_Name=Live%21+24-bit&Product_ID=10315&modelnumber=&driverlang=1033&OS=26&drivertype=1&x=17&y=9)

  • :K8N Neo4 SLI Platinum bios problem

     I have a strange problem with this bios, it goes back to default when you shut it down for awhile.
    The date goes back to Jan 1 2004 and all settings go to default.
    I've changed the battery thinking sure that was the problem, I've heard they've had some problems.
    The funny thing is if you shut it down and then restart it it's ok, but if you leave it for awhile it goes
    back to default. I flashed to 3.7 bios thought that might do it, but no such luck.
    MSI said just get the board or bios serviced, has anyone ever got a new bios chip from MSI?
    I'm trying to get this fixed without all the hassle, but it's not looking good.
    I like the board everything else has went fine, I guess I could leave it running 24\7's.
    When you make changes in the bios all works great, no problems except it won't hold them.
     3000 daabp lbble 0521                          Thanks for any ideas on this
      K8N sli
    2x6600gt
    2x512 ocz raid silicon
    550 antec ps

    I checked the sticky's (which I should have done to start with) I see there have been a lot of
    problems like this.
    Most of the problems have been with the K8N Neo4 Platinum, mine is the sli platinum but the problem
    seems the same.
    The bios shows the new energizer I put in at 2.86.
    I will try to fix this as it was a refurbished board from Newegg.
    I tried the cmos button several times and it made no difference, most of the complaints were having
    to change batteries every 2 to weeks.
    The new battery I put in didn't last the next morning when I booted it up it was right back to default
    and didn't even see the raid setup.
    It only takes about 1 minute to reset it but thats a pain in the butt, as I said if you just shut it down
    for a little while it saves the bios setting's fine.
    I like the board, it overclocks fine if you can keep the settings.
    I'm going to take the board out where I can get a good look in the batt. holder and see if I can
    see anything that might short the batt.
           Thanks for the reply  and any other suggestions   

  • Changing from K8n neo4 SLI Platinum to a K8n Diamond Plus

    Is it a  or  to try and just change  components and everything over and hope it boots up or get some help here in the forum for my answer? I am perplexed , one techie says it probably will need formatting and reinstall :biggthumbsdown:and yet another says tht they are both nf4 chipsets and should be able to boot up . What do you all think will work for me ? Maybe one of you has a solutin for me that is better than formatting and reinstall.  Thanks for your help

    Quote from: limpet on 08-July-06, 08:43:56
    yeah , the platinum won't give me 16 x video with the sli switch card in non-sli mode.
    that's strange, it is the second time that i've seen this problem on the forum, but i never had any problems with mine. however, i thougth that you were going for the extra memory voltages that the diamond plus can provide, because today's graphic cards are still far away from taking up even the 8x pci-e bandwidth. but if you got a good deal, go for it. both of them are excellent mobos.
    you probably won't need a clean system install, but i would suggest that you do it anyway. unloading old drivers and replacing them with new ones will always cause the system to slow down, even if you won't notice. that's why, for a new build, it is always suggested that you go with a clean OS install.

  • K8N Neo4 SLI Platinum-swap AMD 3500+ for Opteron 170

    The time has come to upgrade.  Wanted to check with you guys to make sure I'm not forgeting anything before I swap out my 3500+Clawhammer for a brand new Opteron 170 Denmark.
    I have removed my overclock and reset bios to defaults
    MB is    ms-7100 v1.0
    Bios shows with CPUz as     6.00 PG (dated 9/9/05)   I belive it is really --->  (3.7) 9/9/05
    current windows install reads as (uniprocessor)
    Should I just reset CMOS... install new CPU and I'm good to go?  Any advice would be helpful, I have tried to read up and thats what I came up with.

    Quote from: lbot on 15-February-07, 11:23:04
    I was looking to upgrade to the AMD Opteron 185 (Denmark). I haven't seen any publication from MSI yet and they haven't tested it yet. Does anyone have a similar board with an Operton 185?
    The Opteron 185 is just a faster version of the others.
    I would be real supprised if it wouldn't work.
    MSI CPU publish-testing-results is mostly slower then AMD puts out CPU's, but as it's a Denmark (just like the others), it would be strange if it failed.

  • USB Stopped working - K8N Neo4/SLI Platinum

    I am using Windows XP, no service packs.  I downloaded the latest chipset drivers from nVidia, still no success.  USB worked for about 2 days and then just stopped after the computer was turned off for about 12 hours.
    The BIOS is dated 12/24/2004 and appears to be newer than the bios available on the support page.
    The only card installed is a single gForce 6600 GT.  All four ATA positions are taken with two hard drives in the first chain and two dvd drives in the second chain.  Noting has changed other than adding a case fan and plugging it into the header by the CPU.
    I have tried all four rear USB ports and none of them work.  I then went to the BIOS and changed from 1.1+2.0 to 1.1 only.  Still, nothing works. 
    If this doesn't start working soon I'm going to have to get an RMA from NewEgg.com.

    You need at least sp1 installed for USB 2.0. support.

  • K8N Neo4 SLi Platinum wireless pci card

    I bought US Robtics Turbo wirless card adapter. I installed the card into the comm port and the software that came with the card. The system sees the card as Network Controller in the device manager. I've installed all the drivers that is avaliable for it, and nothing happens. I'm running XP64 and the bios hasn't been updated from the original bios, should i update the bios or find a wirless card that will work on XP64?

    Thx for the reply.
    I've tried all the other pci slot, got the same result. The systen sees a network controller that is with out a driver.  I contacted US Robotics support and the guy suggest upgrading the bios.

  • MSI K8N Neo4 SLI Platinum power requirements

    Is it true that it needs a -5v rail on the PSU in order to properly power the onboard SB live?

    The 12 volt and 5 volt rail are allowed a 10% tolerence and on very high end PSU they actually go 5%.
    12 volt +/- 10%= 13.2 max and 10.8 min
    12 volt +/- 5%= 12.6 max and 11.4 min.
    The biggest mistake you can make is using software to check voltages. Software and BIO (BIO is just software) readings are not accurate.
    The only way to see what is really going on is to backprobe your P/S connector or a molex cable while system is booting, running and then under load using a multimeter.
    I will include a little thing that I made up a few years ago for someone else, mind that it is a few years old but most of the ratings still hold true and you can adjust it to meet your needs. Like a few others I think that might have memory issues or maybe a driver problem.
    Here it is then:
    A 7200rpm HD draws around 20 watts, this 20 watts includes both the 5v & 12V rail.
    HD and CD's generally are figured at 2 Amps per device, let’s brake this down some.
    Spin-up: 12V x 1.3A + 5V x 650mA = 19W
    Read/Write/Idle: 12V x 350mA + 5V x 700mA = 7.75W
    Seek: 12V x 675mA + 5V x 725mA = 12W
    Those would be typical for a 7200 rpm IDE drive. As you can see a HD requires more power at start-up then during actual operation. This is why sometimes a PC takes a few tries to start up before it will actually make a successful boot and once it boots to windows all seems well or sometimes a occasional restart, which would indicate a weak/ bad P/S.
    Now to find the power used by the CPU you can check either AMD or Intel for the spec sheets on that CPU or you can follow this link that has tons of CPU ratings, CPU specs.
    Some more basic mathematics… When a 12-volt circuit is drawing 10 amps, it is consuming 120 WATTS of electrical power. 12 Volts X 10 Amps = 120 WATTS.
    This is the formula: P = E x I
    P - Watt (power)
    E – Voltage (electrical pressure)
    I – Amperage (current flow)
    Serial/PS-2 ports draw <35mA and if you have USB ports then they have a maximum of 500mA per port, again only if they are used- no use means no draw.
    The PCI slots are allowed 5A of the +5V, 0.5A of the +12V and 7.6A of the 3.3V Max per slot, again that is if the slots are used. So if the serial ports, PS-2 and USB ports are being used you are looking at around 5A draw on the MB, which would be around 20 Watts.
    So now we can add things up. (This is just an example of a basic system)
    MB=20W
    CPU= 60W, used as a norm.
    HD=20W
    CDRW=25W
    DVD=20W
    Graphic card=15W / newer GF4 and ATI 9000 and up= 35W
    RAM 10 Watts per 128 MB
    Network Card 5 Watts
    Average per PCI Card 8 Watts
    Total around 200W for this example.
    Now this will fall on different rails and that is were things get tricky, because as you see in my above break down of the HD that a HD use's both the 12V & 5V rail. This is why it is important that the 12V rail be at least 18 Amps if you plan on having more then 1 HD and case fans. Then you have the 3.3V & 5V rails that need to be strong too, the 3.3v rail is actually not so important with newer DDR MB and today’s CPU’s as it is mainly supplying the PS-2 ports power as well as some device cards. Most newer MB use the 5v and 12v rails mainly to supply the demands of today’s devices.
    Now this 200W is the bare min what is needed for things to run but in the real world you will want to add 50% to the 200W for your min P/S need, this allows room for spikes and heavy demands and a little head room to add hardware in the future.

  • K8N Neo4 SLI Platinum / Opteron 170 Overclock Help

    Having just replaced my 3500+ with a Opti 170 it is time to Overclock
    Previous Overclock with 3500+ at 2.5
    10x * 250 = 2500  (Cpu Freq)
    10 / .8333 = 12  (166)
    2500 / 12 = 208.33  (416.66)
    250 * 4x = 1000
    mem timings at 2.8v   (2.5) (3) (3) (8) at T1 
    Opti at same settings as above
    (getting some drops to desktop with BF2, and some lockups when rendering with Sony Vegas)
    Can anybody help me with those mem timings, I'm sure thats the problem.
    For now I am back at stock settings (see below)

    Quote from: MANIAC ~VVV~ on 16-February-07, 01:54:32
    Bio's reset and back at stock settings
    as shown in sig
    btw nice cpu congrats
    take care for dual core 1st:
    install Dual Core HotFix V4 --> https://forum-en.msi.com/index.php?topic=103843.0
    reboot.
    install Dual Core Optimizer --> http://www.amd.com/us-en/assets/content_type/utilities/Setup.exe
    reboot.
    well apply your stable memory settings from BIOS.(etc basic timings, mem. vcore).
    you have to find out max CPU freq. with corespond vcore. and keep HT link and memory freq. with acceptable range during testing.
    look here for tips as well: https://forum-en.msi.com/index.php?topic=105389.msg777869#msg777869

Maybe you are looking for