Does Logic Work With USB Keyboard?

if so what ones would you recomend?
also a portable mic, doesnt have to be great quality that can go in the mini jack of a mac book. just for ideas.
thanks

Hi Syn,
The answer is yes.
If your just looking for a basic keyboard to just record onto logic, take a look at the keystation range from M-Audio. Ive had one for a while now and never had a problem. I don't need much else for what im doing.
As for something a bit more advanced i wouldn't know enough to reccommend something. But the Keystation Pro 88 or Axiom range look ok.
On the mic side of things i have a JTC CX-07S Mic.
Nice and cheap and very portable. You will have to get a 1/4 " adaptor for it but it will do the trick.
Hope this gives you a few ideas or at least points you in the right direction.
Cheers
M<<br>
PB G4 1.67ghz Mac OS X (10.4.9)

Similar Messages

IOS7 does not work with BT keyboard

Passcode typed in Apple wireless keyboard cannot login to iPad running iOS7 at first attempt.
Also several other username & password fields do not recognize Bluetooth keyboard.
Any known workarounds?

I'm with you. I went from a Windows HTC phone which worked perfectly to an IPhone 5S and now the message feature on my 2010 Honda Insight does not work. Since I do quite a bit of traveling, this is a little annoying.

Does iPhone work with USB 1.1 on iMac 17 inches 1 GHz ?

My GF just got her iPhone and I tried to use it with my iMac but it wouldn't show up in my iTunes. I wonder if this was because there are only USB 1.1 on my Mac (5 of them). Please post a response if you happen to know about this and I will really appreciate it, thanks a lot. Nick

The iPhone specs are as follows
Mac system requirements
Mac computer with USB 2.0 port
Mac OS X v10.4.10 or later
iTunes 7.5 or later
Although it may work on some systems results can not be predicted if you go below those specs, it is a known issue that the iPhone does not like any USB below 2.0,
hope this helps

975X Platinum PowerUp - PS/2 Mouse wouldn't work with USB Keyboard!!!

I cannot get my PS/2 Mouse move with when USB Keyboard is connected. Both PS/2 Mouse and Keyboard work fine together. Similarly, both USB Mouse and Keyboard are OK. Any solution??? Would be grateful for any assistance. Thanks

Quote from: mike315 on 09-February-07, 23:00:26
I built two 975X PUEs for two different people, finished them about 10 days apart. They both ran fine for about a week and then on the same day, in two different houses over 25 miles apart they both "lost" all USB devices. Yes, the USB Controllers still showed just fine in Device Manager but every USB port was dead.
I went to both locations, UNinstalled ALL USB Controllers, let WindowsXP re-boot and re-find all controllers, which it did. All USB ports went immediately active and have been fine for about two weeks since. By the way, I didn't unplug or re-plug anything.
I can't prove my theory, but both PCs were set to download WindowsXP updates AUTOMATICALLY and INSTALL them, and both PCs were using Broadband, i.e., "always on". Tell me I'm crazy, but I think a WindowsXP update knocked out the USB ports.
OK, I'm crazy, but answer me this: What are the odds that two PCs - in different locations - would experience the SAME exact HARDWARE problem - and no others before or since - at the exact same time?
And, if you Google for USB problems IN GENERAL, you'll find other people experiencing the same thing about the same time, especially if they use WindowsXP BUT do not have Internet Explorer 7 (IE7) installed . . . which was exactly the situation with my two 975x builds. Also, many of these people identify their recent problems as USB wireless mice problems, which is how both my build PCs were being run. By the way, IE7 has already been identified as causing driver problems with some hardware, e.g., older model scanners.
Very nice, but that really doesn't answer the topic or helps :P nice story though.

Bug report: entering serial number does not work with azerty keyboard

I did not find a place to submit bug reports, so I'm posting here.
During the instalation of Photoshop Elements 8 for Mac, I was not able to enter any numbers in the serial number fields. Some other keys did work (like &é$...). My keyboard is an azerty (Belgium). Notice the numbers on an azerty keyboard have to be entered while holding the shift key. I tried switching the keyboard to "French - Numerical" (wich enables numbers to be entered with shift lock on), and then some number keys worked, and others didn't.
I solved this with a workaround, by temporary switching my keyboard to U.S. English.

You can submit a bug report by clicking "Feature Request/Bug Report" in the upper-right corner:
http://www.adobe.com/support/photoshopelements/
Despite what it says, I've seen no hard evidence that Adobe ever pays attention to PSE bug reports.

HT1379 reset does not work with bluetooth keyboard

although people write on the internet that bluetooth keyboard can initiate boot key-sequences, I cannot see it work...
after updateing to Lion my volume setter is broken.

Since you have a pre-unibody MBP, you can fairly easily change the keyboard yourself. Check iFixit or Powerbookmedic and see if they have replacements available.
Ciao.

Does it work with USB?

I've been importing movies from my DV/tape camcorder to my MacBook over firewire.
Now I want to buy a MacBook Air, which only has USB.
So I tested iMovie & USB on MacBook, and iMovie doesn't see the camcorder.
QUESTION: Is it possible to import movies to iMovie via USB? (Maybe I did something wrong)

Tape cameras are firewire only. MacBook Air is not a good fit if you are going to be editing videos.
You can import from USB camcorders such as the SDHC or Hard Drive-based AVCHD camcorders. But even then, I would not recommend the MBA, because video takes up a lot of hard drive space, and the MBA does not have much.

I bought the last apple wire keyboard , but it does not work with my usb ..

i bought the last apple wire keyboard , but it does not work with my usb hub why ?
the only way it works its when connecting it thrue my powerbook usb ...
the problem is i HAVE TO USE IT THRUE AN USB HUB ... do you think its because my hub is cheap ? 10 $ .... i 've been told that it comes from the fact that i need an auto-alimented usb hub ...?.
suggestions gentlemen ?

I have eyes everywhere. Two of them can see the word "Paris", right below your name, at left.

USB Camera does not work with iChat

Hello,
I'm having a terrible time getting my ToUcam Pro II to work with iChat. I downloaded the iUSBcam program. That didn't work. I downloaded the program Macam, and copied the proper file into the Quicktime Library (as suggested) and that didn't work. I downloaded IOXwebcam, and got an error stating that it wouldn't run due to the fact that it didn't have the proper security settings. Sigh.
So... what am I to do?
I'd like to buy a webcam that does, actually, work with my 8 month old Mac Pro 4 core mac desktop, but the iSight camera is ridiculously expensive. Any other suggestions would be appreciated.
Brad

An X-box 360 cam will do it although not in that list.
Anything that is USB 2.0 and marked UVC compliant or Vista Certified.
Be Aware some Mac Keyboards do not have USB 2.0 ports.
11:57 PM Tuesday; September 8, 2009

External USB HD does not work with HAL:

External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.

I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era

Ipod does not work with new usb

i got my computer cleaned and a usb 2.0 pci card put in and now my ipod does not work with it, can anyone help

tell me what you mean and i will tell. i ask the guy in the shop to remove any viruses and put my files in order and also put winzip on, ad-ware se peronal and windows defender. and to install a usb2.0 pci card, so that i can put music onto my ipod faster. is this enough for you

I am running 10.8 and I am trying to get a E-mu 1x1 midi/usb connector to work with my keyboards. It's not working with any keyboard at all. I believe it is a Mainstage/Mac issue. Mainstage can recognize the the interface but it won't work.

I am running 10.8 and I am trying to get a E-mu 1x1 midi/usb connector to work with my keyboards. It's not working with any keyboard at all. I believe it is a Mainstage/Mac issue. Mainstage can recognize the the interface but it won't work.

Here are two screen shots to show you what I am seeing. The first screen shot shows it allowing me to select (highlighted in blue) my admin user (which is what I am locced in as). The second screen shot shows it allowing me to select the "Guest" user (highlighted in blue). However when I click on the user "Orion" nothing happens. It will not change to highlight that user.

HT4882 hi apple it's kian ! i have mac book air with 10.7.2 version may keyboard light does'nt work with f5 and f6 ! please help me !

hi apple it's kian ! i have mac book air with 10.7.2 version may keyboard light does'nt work with f5 and f6 ! please help me !

Hello Kian,
This may sound silly but if you put your hand over the isight camera, do the lights change on the keyboard?
Ryan

Brightness control does not work with the bluetooth keyboard connected on my iPad2. Please someone could help me ?

Brightness control does not work with the bluetooth keyboard connected on my iPad2. Please someone could help me ?

Julien-
I have the Apple MC184LL/A Bluetooth Wireless Keyboard. The brigtness control works with mine, as do most of the other functions.
Try cycling the keyboard off and on. Hold the power button until the green LED goes out. Then press it one more time to turn it back on.
You might try resetting the iPad's network. Go to Settings-General-Reset-Reset Network Settings. Then you may need to reconnect your WiFi and Bluetooth.
If that doesn't help, try resetting/rebooting the iPad. Hold both the Home and Sleep buttons for several seconds until the Apple logo appears. Ignore the "Slide to power off" arrow. The iPad will restart in a couple of minutes. Resetting this way will not hurt anything, and sometimes clears up mysterious problems.
Fred

How does lion work with logic 9.1.4?

how does lion work with logic 9.1.4?

Greetings,
So far, everything seems as stable as before. Which doesn't actually mean its rock solid, but otherwise workable. I'm running a Focusrite Saffire Pro 24DSP with beta audio drivers. So far, everything is running well. I decided to jump into the 64bit work environment with Logic. I have yet to encounter huge problems with the 32bit audio bridge. Just making sure I bounce everything that is 32bit.
As for everything else within Logic, I can't say I hate Lion. Matter of fact, Lion seems buggier than Logic at the moment. Logic handles well in Lion, but Lion on its own overall is a different can of worms. I am mixed about a 10.7.1 update. Usually, it fixes something on the OS, but breaks something else in Logic.
I have faith that Lion will turn out to be as solid as Snow Leopard. SL was my favorite OSX so far. Lion still leaves allot to be desired in terms of stability.
Again, answer to your question: for me, Logic and Lion play nice.............for now.
LGK

Does Logic Work With USB Keyboard?

Similar Messages

Maybe you are looking for