Does MSI KT4 Ultra supports Kingston KVR400X64C25/256 ?

Hi people !
Can u pls help me with this ? I bought those memory but i dont know if its works well...
Thx in advance

Is This your board?
If so, it claims to support up to 2 DDR400 modules, but only at DDR333 speed with a 166/333 FSB CPU.

Similar Messages

Does the KT4 Ultra Support Sempron CPU's ?

Does the KT4 Ultra support Sempron CPU's ? The CPU support page doesnt seem to mention this motherboard....
If it does what BIOS rev do I need ?
If it doesnt what will MSI add it, as I see that the KT4V does support the Sempron ?
Thanks.

>If it doesnt what will MSI add it, as I see that the KT4V does
>support the Sempron ?
Sorry, above should read as follows :
If it doesnt WHEN will MSI add it, as I see that the KT4V does support the Sempron ?

Linux and MSI KT4 Ultra : DVD problems

Hi, I own an MSI KT4 Ultra Pure mobo. The vt8235 Southbridge is supported in the lastest version of the Linux Kernel, 2.4.20 . After upgrading the kernel all seems to work fine, but when the system try to initialize my hdc (Secondary master of IDE, a DVD reader DV-5800A from NEC) it locks up with the message :
hdc: device {Busy}
hdc: drive not ready for command
ide1: reset success!!
and start looping with this message.
What can I do to get work my DVD Reader? With my precedent MoBo it works perfectly
Thanks
Bye

Hmmm that error used to happen with an older kernel and an ALI chipset. If you leave it long enough does it give up trying and continue to boot? The ALI did this eventualy.

PROBLEMS AGAIN, MSI KT4 ULTRA GIVE POOR STABILITY IN MY SYSTEM!!!

Hi, i get problems when overclock (fsb) my cpu with 133 fsb to 136 ONLY!!! , only support the overclock my cpu 1800(1533mhz)--to(1580mhz), high fsb 137 or high freeze , restart my system when run games or aplication with geforce 3 ddr 64mb, i modify vol agp to 1.8 , but get error again.
HELP ME!!!
I NEED NEW BIOS THAT STABILIZE MY SYSTEM!!!
System:
MSI KT4-ULTRA 6590-SR
CPU XP 1800+
256 DDR SANSUMG
T.VIDEO GEFORCE 3 DDR 64 detonator 41.09 agp4x
WINDOWS XP PRO SPK1
POWER 350 WATTS CODEGEN

Thanks for you help, but my power 350 watts codegen work a:
20A---3.3v
30a---5v
However i read guide revision 12-12-02 about psu and all configuration is correct !!!!!!
My powersupply not is problem
I NEED THAT MSI MAKE NEW BIOS FOR KT4-ULTRA!!
Thanks

K8T Neo-FIS2R / Kingston KVR400X64C25/256

As a first time poster my apolgies if this has been covered elsewhere - I have read most of the posts on this forum but found no specific reference. Please just point me in the right direction if i am wrong!
I bought the Kingston KVR400X64C25/256 modules because:
a) they were listed by MSI on the list of tested Ram
b) they were on Kingston's list for the K8T NEO &
c) they were in stock. However...
If installed in DIMM 2 & 3 (as per MSI tested RAM pdf) the system crashes on trying to load Windows. DIMM 1 & 2 'works' if that allows for 8 or 9 restarts/day. I tried 1 & 3 to see if that improved the situation, but if anything it was worse. I have tried increasing the RAM voltage to 2.6 but there is no discernable difference. Upping the TRCD to 4 makes little or no difference.
Memtest86+ initially found no errors (16 hrs/93 passes) but when left running for a week came up with 10 errors (8 in test 6, 2 in test 4). MemTest (http://hcidesign.com/memtest/) gives me an average of 10 errors for 300% pass.
I'm now trying running the memory at 2.7v (within Kingston's ±.25v range).
In the meantime, has anyone run this memory without any problem - i.e. is it a simple case of faulty memory? Equally, has anyone had similar problems and found a solution?
thanks
MSI K8T Neo-FIS2R
AMI rev 1.2
AMD Athlon64 3000+ AMD heatsink/fan (working temp around 32°C)
2 x Kingston KVR400X64C25/256 (DIMM 1, DIMM 2)
NVidia GeForce3 driver v53.03
Antec TruePower 430W +3.3V 28A, +5V 36A, +12V 20A. Max load 410W
IDE1 ST340016A (master) ST320014A (slave)
IDE2 MSI DVD-ROM D16 (MS-8216)
Soundblaster Live 5.1 platinum
Windows XP Pro Version 2002 service Pack 1

Quote
Originally posted by Bas
Hi,
Sorry to say, but as soon as you get errors in memtest, no matter after how many hours, you need to try other memory.
As your memory seems to be unstable....errors in memtest are a NO-NO
hmmm! What if memtest, Prime95 etc. detect no problem over lengthy periods when sticks are individually tested in DIMM1 - as well as the system not crashing once - , but boot failures/memory dumps etc. abound when same sticks are individually placed at 2 or 3? Is this still a memory issue?
For what it's worth I have found Kingston's technical support more than helpful.
MSI K8T Neo-FIS2R
AMI rev 1.2
AMD Athlon64 3000+ AMD heatsink/fan (working temp around 40/42°C)
2 x Kingston KVR400X64C25/256 (DIMM 1, DIMM 2)
NVidia GeForce3 driver v53.03
Antec TruePower 430W +3.3V 28A, +5V 36A, +12V 20A. Max load 410W
IDE1 ST340016A (master) ST320014A (slave)
IDE2 MSI DVD-ROM D16 (MS-8216)
Soundblaster Live 5.1 platinum
Windows XP Pro Version 2002 service Pack 1

MSI KT4 Ultra and AMD XP3200+

Hi,
Is it possible to run an AMD Athlon XP 3200+ on the MSI KT4 Ultra Motherboard?
I know the motherboard supports FSB200/266/333, but will the cpu work if I manually set it to FSB400 in the bios?
Thanks for you help.

I don't think the cpu is unlocked, it is an original 3200+.
I thought you need an unlocked cpu if you want to overclock the cpu.
I just want to leave the multiplier on auto and set the frequency to 200MHz (its original setting).
The reason I need to know is that I stupidly bought the cpu without checking my motherboard FSB support and I cant return the cpu.
I have not received it yet and wanted to know if it was possible to get my computer up and running even if the KT4 Ultra does not officially support FSB400.
Would there be any harm in trying the cpu in my motherboard.
If anyone has managed to run an AMD XP3200+ cpu on a MSI KT4 Ultra, please let me know.
Thank You.

MSI Kt4 Ultra - Sound on Board

Hello, I have a problem with my onBoard sound.
Sry for my english, I am german.
I have a SB Live Volue soundcard and i want to install it, but when i deactivate the onBoard sound i cant't delete the drivers from it.
Pls, help, how can I deactivate the Sound-on-board, and install my other soundcard right ?
Pls, when someone is German here, write in german.
thx.

Yes, I disabled it in "Integrated Peripherals" the "Serial ATA Controller" and the "Audio Controller".
Is there someone more, I have to disable ?!
Or have I to deactivate it on the mainboard, too ?!
And how can I delete the drivers from Windows ?!
This drivers are:
Audiocodecs
Legacy-Audiotreiber
Mediensteuerungsgerät
Vidiocodecs
I have Windows XP and Win2k, because I use Partition Magic and Boot Magic.
MSI KT4-Ultra
Athlon XP 2000+
GeForce4 MX 440
256 DDR Samsung 333Mhz
SB Live 1024
Midi Tower 350 Watt

MSI GeForce3 Ti200 + MSI KT4 Ultra [problems]

hi, every time i am on my computer my computer restarts and random intervals and when it returns to windows from a reboot it telss me it had a display device driver failure.........i never used to have this problem b4 and only seem to get it now since i installed my new motherboard (MSI KT4 Ultra). I did a fresh windows install and am running the latest VIA drivers, i tried all the nVidia drivers out there old/new......same problem....... any help would be great, cause it's getting real annoying now.
This is the error i get:
Quote
The driver for the display device was unable to complete a drawing operation. Please check with the device manufacturer for a driver update.

well after removing the display driver and now running the standard vga driver, i am positive the thing at fault here is the driver.....because i my compter does not spontainiously reboot nor do i get any display errors, hoever my computer activity is very limited, i can not run any games or use any graphic intensive apps.
.......since the driver IS at fault, will MSI please release a fix or a new driver that will resolve this issue
Thnx.

Problem with my MSI KT4 Ultra

Hi all!
I have a BIG problem, I have tried to look at this board, but there is many different answers out there ;(
I have KT4 Ultra with Athlon XP 2600+
I have set FSB to 166, and when I startup BIOS says Athlon XP 2600+.
But in windows system, it only says:
AMD Athlon XP2600+
2.09Ghz !!!!
768Mb RAM
Why is windows only says 2.09Ghz??
AND, I think my system is very slow. I used to have AMD 1200Mhz. And this sytem is almost like my last computer.
My System:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive

Quote
Originally posted by swedecom
Ok, I use these settings in my BIOS, are they right for my system??
MY SYSTEM:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive
MY SETTINGS IN BOIS:
Spread Spectrum = +- 0.25%
CPU FSB Clock = 166Mhz
CPU Ratio = Auto
CPU Vcore = (V) Auto
DDR Voltage (V) = Auto
Termination Vol (V) = Auto
AGP Voltage (V) = Auto
Hope someone can help me out

No optical-out sound on MSI KT4-Ultra!!

Hi, I have recently set up a system based on the MSI KT4-Ultra board. I'm using an Athlon XP 1700+, a Radeon 9000 video card, and I've installed Windows 98.
Although all the drivers and audio applications which MSI provided installed fine, and 2-channel audio from the on-board sound chip works great both for music and for the 3-4 games I've installed so far, I can't seem to get the optical SPDIF port to work! I bought a cable and connected the computer to my Sony MD-player and attempted to copy my CDs onto MD. I go into the MSI control panel and check the box to enable SPDIF-out, removing the speaker cable from the analog line-out just for good measure. When I plug the optical cable into my MD it recognises digital input and prepares for recording. I press record on the MD and play on the computer's CD-player app, but the MD LED shows "no signal". I'm pretty sure both the MD recorder and cable are OK since I've used them to copy CDs from a Kenwood portable CD-player quite recently, so it must be the MB that's giving me problems. Indeed, when I've stopped playback in the CD-player app and went back into the audio control panel, I found that the SPDIF box had been unchecked of its own accord. I've tried this several times, and I've unplugged the S-bracket and reinstalled it all over again just to make sure it was plugged in properly, and I still get the same problem. All audio works fine except optical out! Haven't got a coaxial cable or recorder so I can't check if the coaxial port is equally buggered or if it's just the optical, but I'm getting really annoyed here: this was the one feature I liked best about this board and the only one which isn't working! Any ideas, anyone?

dude, i think i can get u ur signal, but currently i can only get silent recordings, u may have better luck.
on the minidisc, there should be a switch or button that will toggle synchronised recording on and off, turning it off should get u a signal, but it wont be in sync wiv the cd, ie u cant trust it to form track gaps.
hope that helps, done flame me if it dont, if i manage to get substance to my recording, i will send u the info just in case.
take it easy

MSI KT4 ULTRA-BFISR + Ati Radeon 9700 pro = not good??

Hello everybody!
First of all, i youst have to say that i think MSI have the best motherboards....
Here's the problem (i haven't buyed anything yet!):
I am going to buy MSI KT4 ULTRA-BFISR and ATI Radeon 9700 Pro, but i have read many places that Radeon aint working with MSI KT4-based cards! Im am going to buy an 520W Power (i aint so good in english so i hope you now what i write :D )
I am also going to buy 2 x Cosair pc3500 xms ram... Is this one working with the motherboard by the way?
But my question is: Will the Ati Radeon 9700 pro work with this card? (i must remember to buy the 1.3 version!) I am gonna get my Radeon 9700 pro from USA, how can i now when i order that is an 1.3 card?
Thank you for answering! :]

I think also that even there is two drivers, that is not a reaseon why it isn't work. One time I install only standard VGA drivers, but result was that I got two standard VGA driver. 8o
First time I try without VIA drivers, then with 4.42 and 4.43 VIA drivers. Result was almost same all the time, it always crash when Nature test start, but this exist also to older mobo (Abit KT7A-RAID). Problem exits few games they lock up or stuttering. Ati demos works fine, but one time that car demo stuttering a lot, but I transfer data at same, so I'm not sure what was reason.
This moment I don't have possibilities to try Hyperion 4.45 drivers or something else, because it's my friend computer.
MSI KT4V 6712 (Bios 1.0)
AMD Athlon 1.2
512 MB DDR 333 RAM
SoundBlaster Live
ATI Radeon 9700 Pro (Club3D)
Power 300W
Realtek Ethernet card
Samsung 40GB harddrive
Samsung DVD
VIA 4.42 and 4.43
WIN98

MSI KT4 Ultra! A little question.

Hello. )
I'm very interested, in the new MSI KT4 Ultra, but i've a doubt:
The pure version of the KT4 Ultra, has a fan on the chipset?
How many IDE channels come with this pure version?
Thank you, and sorry about my poor english. :D

You can modify de FSB in the bios, but there is a jumper that provides these 3 options, 100mhz, 133mhz and 166mhz. 100mhz for the duron cpu's, 133mhz for the Athlon xp Palomino and Tbred, and 166mhz for the athlon xp Barton ( not 100% confirmed).

MSI KT4 ULTRA MS-6590

I have this motherboard: MSI KT4 ULTRA MS-6590 sempron and I have already bought the new CPU SEMPRON (AMD Sempron 2400+). I want to know if my motherboard is compatible with new CPU.
Thank you
Sorry for my English, but I'm Italian.

Hi
Not according to http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=356&kind=1

MSI KT4 ULTRA MAX VCORE

Is it possible for MSI to add higher Vcore settings with a BIOS update? The MSI KT4 ULTRA has a max Vcore of 1.85 which doesn't really help the overclockers much. If they could get the max Vcore to 2.00 that would be great for XP overclockers. )

I'm not complaining about my KT4 ULTRA. I think its a good board for people who aren't really into overclocking and performance tweaks, but I love to tweak the performance of my rig. I hate to say that other motherboard companies seem to get the picture, that they should make their boards as overclocking friendly as possible. ASUS, Abit, Epox etc. are considered the best because they have conquered into the overclocking market. I wish MSI would throw their hat in the same market because I personally feel they can.

MSI KT4 Ultra-SR (MS-6590) And IDE3

Rig is As Follows:
MSI KT4 Ultra-SR (MS-6590)
AMD Athlon 1000Mhz :(
512MB DDR333 (PC2700) x1 stick
MSI GeoForce 4 Ti4200 8)
IDE1: Western Digital 40Gb 5400rpm (win xp pr) as master & Maxtor 80Gb 7200rpm as slave
IDE2: Liteon 52x24x52 CD-RW ) as master & Samsung 12x DVD as slave.
Soundblaster 5.1 Live PCI
350w Power Supply
MSI D-Bracket 2 & S-Breackets Fitted Also.
I have Three Questions.
>My CPU has a FSB of 200, but the bios (version that came with board) shows it as 100 FSB. See here for athlon bus speeds
Is it ok to increase the bus speed without damaging the processor.
>The two brackets that i have fitted (s and d brackets) do not work. Why?
>What are the optimal and settings for my ram (PC2700 512MB DDR) and GFX Card (MSI GF4 TI4200).
>Oh yeah, my CPU is now operating at a higher temp than before (using old K7VZA ECS Mobo) @ 50-55. Is this normal??
Sorry for the n00b questions, it's just that this is the first time iv ever taken my PC to pieces and re-configured it myself :P
Thanks in advance. -RjA

I can help a little 1000MHZ AMD chip=200FSB XP CPUs=266FSB this is CPU speed . AMD 1000MHZ CPU needs to run @100FSB where a XP CPU can run @133FSB This is MEMORY speed . Trying to crank that poor old chip up to anything other than 100 will do you NO good. You need to buy a bigger cpu of the XP kind. A lot of the older XPs can be had for a low price. 50c isn't not super hot. My KT4 runs in the 40s. You might want to think about a bigger cpu cooler to bring the temps down a bit. Most of your settings should be left at system default, since you only have a 1000MHZ CPU. When you go up to an XP then you can make a few changes. Regards BIGDADDY51 :D :D

Does MSI KT4 Ultra supports Kingston KVR400X64C25/256 ?

Similar Messages

Maybe you are looking for