Does my board support dualchannel?

Hi there,
maybe a stupid question, but ... does my board MSI 6702 K8T Neo-FIS2R support dualchannel-ram? Or is this only possible with pentium-boards?
How can I determine it, if my modules (both 512 mb mdt ram ddr 400) run in dualchannel?
Bye,
Marcel

Quote
Originally posted by Jocko
Quote
Originally posted by skippy9146
Quote
Originally posted by Jocko
Hi
Your right Ven42. the K8T Neo FIS2R, is single channel unregistered non ECC. but if dual channel is fitted it will run as single channel.
The 939 pin Mobos are dual channel, registered Ram boards.
Cheers
jocko
Ooops my bad
Too many NEOs floating around to keep up with.
But I do know that 939's are non-registered RAM boards (got one). 940's use the registered memory.
Know the feeling.
I thought the Via Neo2 was dual channel and registered Ram, I live and learn.
cheers
jocko
Well, I have the Platinum w/ the Nvidia.... I ought to put it in my sig.

Similar Messages

Does my board support FSB 800 Cpus?

Hi!
I have a MSI-845PE Max-L Mainboard (supports FSB 533Cpus).
Can it support the new FSB 800 CPUs? Will there be a BIOS-update?
I can't imagine, the Heatsink without an active fan can cool the nb @ such a high FSB!!!
tia
Geforceraid

None of the 845 based chip sets were originally designed to support 800mhz fsb. Some board makers have found they can overclock certain versions of that chip set to run at 800mhz. Even if the mobo maker sells it as a 800mhz board it is still overclocked. The new 875 chip set is designed to run at 800 mhz and as such should prove to be more stable. Also if you have an 845 series chip set running at 800 mhz it is already overclocked to the max so there is little or no room for additional overclocking. The new 875 chip set should have plenty of additional room for overclocking since it is only running at spec when at 800 mhz.

Does the X58 boards support intel 2 core quad 775?

i have a question the X58 boards support 2 core quad processors? because it says 45 nm support.

For future reference, look at the socket of cpu.
Core 2's are socket 775 or LGA 775, X58 is for Nehalem or better Bloomfield cpu's, new architecture and has socket 1366 or LGA 1366.
The numbers stand for the number of pins found on the bottom of the cpu, the core 2's had 775 contactpoints, the new Nehalem 1366.
The 45 nm you refer to is the productionproces on which it is made on, e.g. 45 nm.
The smaller this number becomes, the next step is 32 nm, the more processors can be cut from a wafer.

Does iTunes 11 supports 5.1 Speakers?

Does iTunes 11 supports 5.1 Speakers? If yes which all speakers does it support and how to activate it on iTunes?I am able to play music in 5.1 surround mode using other players such as WMP 11, VLC, GOMP, WINAMP but when I play music using iTunes it only plays in stereo mode i.e. 2.1. The side / rear speakers do not give any output.
Specs:
Windows 7,
Gigabyte FX990-UD3 Motherboard with 7.1 audio on-board support using 6 3.5mm jack pins.
Creative SBS A520 5.1 speaker system.
iTunes 11.1 installed.

I think you mean HandBrake. I use HandBrake and I know exactly what you're talking about. Unfortunately, sometimes HandBrake shows that there is CC available but when you rip it, the CC doesn't appear in iTunes. I notice that but there is no way around it. This only happens with newer releases (I'm positive you only see this issue in newer films). HandBrake needs to be updated to keep up with the newer encryption by DVDs. There is nothing we can do. Hope that this post answered your question.

Definitive list of what boards support Prescott CPU

I was just look around and found this. It look like some boards support the Prescott better than others1
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=prescott

Hey Guys
Just looked at the post and am confused lol
I am using a 875P Neo-FIS2R so by the looks of the link by ghostwalker my mainboard wont support the new Prescott. V vvvv bad lol.
But on seans post it seems that my mainboard does support it. A while ago I saw a link on the forum to some official statement from MSI saying the 875P Neo-FIS2R would support prescott. Wot ya guys think cos otherwise im a bit skrewd lol
Cheers
SAspaz

Does the mobo support Z68A-GD65 (B3) was removed?

Does the mobo support Z68A-GD65 (B3) was removed?. Currently not find BIOS updates and Virtu does not work with the Core i5 3570K.

Well, that is highly irregular! One day it's not found on the Websites, and now it is. That was not on the Global site yesterday, because I looked. And a (G3) UEFI/BIOS at that.
You are mostly on your own on this one. The 'key' or 'certification' has obviously been removed from hardware/firmware or whatever it is on the board that handles that aspect. How you get it back depends on what you decide to do. If it is that important to you, the mainboard may have to be restored to it's former glory of Sandy only UEFI/BIOS's. Use the link in one of my previous replies and contact MSI Technical about all this. They are the only ones that can help you possibly get the Virtu problem resolved. What have you really gained using an Ivy CPU on a Z68 (B3)? Good luck!

Does Neo2 LS support Celeron D ?

Hi !
I have searched a bit in this forum, but I can't find any hard fact about this question : Does Neo2 LS support Celeron D ? BIOS Upgrade ?
Regards
Kjetil, Norway

Celeron D and Prescott cpu ready MB;
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=prescott
If you got 865 PCB 1- version 1 board, you have to update bios to 2.3.

I want to buy MSI N630GT-MD4GD3 but does your gpy support my mainboard ?

hello msi i want to buy MSI N630GT-MD4GD3 but does your gpu support my mainboard ?
please help me guys
here is my mainboard spec :-
GRAPHICS   º Integrated Intel® Graphics Media Accelerator 950 ( GMA950 )
º Max Dynamic Video Memory up to 224MB(System Memory greater than or equal to 512MB)
EXPANSION SLOT   º 1 x PCI Express x16 slot
º 1 x PCI Express x1 slot
º 2 x PCI slots
CPU   º LGA775 socket for latest Intel® Core™2 Duo /Pentium 4 (6xx)/ Pentium D /celeron (4xx)/Celeron D Processors
º FSB 1066/800/533 MHz
CHIPSET   º Intel® 945GC & ICH7
º North Bridge: Intel® 945GC
º South Bridge: Intel® ICH7

This is a Users-to-Users Forum. If you want to ask MSI: >>How to contact MSI.<<
Considering PCI-E compatibility it is fine with a Nvidia card. Still nobody can guarantee you an old 945GC board won't have bios problems supporting a current generation vga. Most likely it will work though.

What type of HDD does MS-6382 support?

Hi,
My system has a MS-6382 mobo & I've got to change to the hard drive. I've been looking at ebay & the link below describes a HDD which has "ATA/133 or SATA interface and capacity of 120 GB"
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&category=16178&item=5208766733&rd=1
I don't know much about computers, or even the right questions to ask really, but does the 6382 support 7200rpm drives, ATA/133? What general specs for a HDD should I be looking for?
I would be grateful for any help anyone can give!
Here is some info on my current HDD:
HD Tune: ST380020A Information
Firmware version : 3.39
Serial number : 5GC0KMYD
Capacity : 73.1 GB (~78.5 GB)
Buffer size : 2048 KB
Standard : ATA/ATAPI-6
Supported mode : UDMA Mode 5 (Ultra ATA/100)
Current mode : UDMA Mode 5 (Ultra ATA/100)
S.M.A.R.T : yes
48-bit Address : no
Read Look-Ahead : yes
Write Cache : yes
Host Protected Area : yes
Device Configuration Overlay : yes
Automatic Acoustic Managment : yes
Power Managment : yes
Advanced Power Managment : yes
Power-up in Standby : no
Security Mode : yes
Firmware Upgradable : yes
Partition : 1
Drive letter : C:\
Label : MR01-G4
Capacity : 74822 MB
Usage : 17.54%
Type : FAT32
Bootable : Yes
Jorolat

Quote from: Wonkanoby on 19-June-05, 21:26:02
ata 133 is just a marketing gimick.............only data moves that fast is 2mb in the drives cache
the drive will run at about half that speed once the cache is cleared
dont worry about it
Er, I got another question
I'm now looking at this hitachi model:
http://www.cclonline.com/product-info.asp?id=210&pc=dealtime#
which has good reviews (probably for others in the range). I originally saw it on ebay but it turns out to be cheaper buying it from the above supplier.
The question I have is does the MS 6382 support serial ATA? I'm reasonably sure that the above drive is parallel ATA (ie compatable with the MS 6382) because of the manufacturer's info here:
http://www.hitachigst.com/hdd/support/d7k250/d7k250.htm
but I thought I'ld ask before I order it or in case I change my mind (again).
Thankyou for your help
Jorolat

Does lion server support a single email address across multiple devices??

I am looking to move from an outdated Microsoft Exchange Server 2003 to OS X Lion Server but I am unsure as to how Lion will handle email. I do not want to spend money on a new windows server if I can get a Mac Mini Server to do the job. I am a very small business with a number of email accounts for a couple employees and need access to email and calendar from both the office iMac's and my Macbook Pro when on the road. My IT guy says I need Exchange but he's been off base on a few other items recently and I wanted to check with other sources.
I have 2 new iMac's, a MacBook Pro, an iPad1 and and iPhone4 on the mac side of things and 2 windows computers running XP. I would get rid of the windows computers completely if not for my CAD program which runs best not in a virtual machine mode.
How well will email and calendar entries sync across devices?

I have a very similar setup at my office. Lion Server will push email, calandar, contacts to all of your apple product with out a hitch.
As far the Windows XP machines, you can access email over IMAP with Thunderbird, and calandars via sunbird or the built in web app.
I would ditch the exchange server move to Mac OS X Server, and never look back.
God Luck!
PS. All of your devices will be in sync all the time.
Shore answer:
Does lion server support a single email address across multiple devices??
Yes.

Does Crystal 2011 supports SAP R/3 4.6?

Friends,
I would like to know Does Crystal 2011 supports SAP R/3 4.6? Please help.
Thanks,
Tilak

Hi,
yes, it does. Here is a Screenshot from the CR2011 SPS6 Data Access File
The (4) indicates:
(4) SAP servers required to have at least the above patch levels. The following correction notes should be applied to your SAP BW / SAP NetWeaver BI system: 1125433, 1161911, 1162349, 1162416, 1170323, 1230303 and 1007048. OSS Correction Note 1007048 requires a manual configuration step.
Regards
-Seb.

Camera RAW does NOT yet support raw files for the new Canon Sureshot S95

Camera RAW does NOT yet support raw files for the new
Canon Sureshot S95.
Adobe, please can you provide an update asap

Hello!
I think that you need to be patient.
There has not been any release of Camera Raw since the release of the camera.
I recommend to try the next version once it will be released, as there might be preliminary support (and therefore not listed).
Usually, Adobe is amongs the firsts to support a new camera.
Even though the Camera Raw team is fielded with wonderful coders, I do not think that they do have a time machine to allow support before they have their hands on a camera

OK, as always I waited before downloading a new OS and I sure glad I did. On the APP store I sorted comments by most critical...and WHOA...what is Apple doing? No support for Logic 9, MS Office? Is Apple only trying to reach the iphone/iTouch crowd? HELP!

OK, as always I waited before downloading a new OS and I'm sure glad I did. On the APP store I sorted comments by most critical...and WHOA...what is Apple doing? No support for Logic 9, MS Office? Is Apple only trying to reach the iphone/iTouch crowd? HELP! I was going to buy a new Mac pro & two 27" monitors but until I see some real problem addressing by Apple...I'll keep what I have and see how everything pans out. If anyone has any comments to ally my fears, I welcome them. I've been a devoted Mac user since 1993. 7500; G4; G5; and my latest Mac Pro...Where do I go? Again...HELP!

Hi there,
If you look through ALL the reviews, they are mainly good. I feel that Lion is an excellent upgrade, although not essential.
There have been some issues with MS Office, but right now, it is up to Microsoft to issue a Lion compatible update, which will come in time. Saying this, MS Office has been working fine on my mac, it seems to be an isolated issue.
Logic 9 seems like a strange issue. Again, an update looks to be coming soon, with Lion support.
I do not feel that apple only focusing on the iPhone and iPad user base. There are many features carried along, but the machine can still be used for pro tools and use just as well. It still is a fantastic, reliable, fast, easy to use OS, which I have had very few problems with. Some additions you may not use, but they don't get in the way. You will love the new Exposé, Mission Control, as it is great for pro users who have many windows open at once, and the new spaces. You may however, never use Launchpad, but you don't have to, just drag it away from the dock!
I really reccomend buying a mac with Lion, although if you are worried about bugs, wait a few months for the issues to be ironed out, and updates to be given. Because the update is so very cheap, I really think you can hardly go wrong. Try it out with your current mac, and if you like it, go ahead and buy your new ones.
Lion is fantastic, albeit maybe rushed.
Any other queries, just ask,
Nathan

Does Apple TV support wireless connection to the new MacBook Pro retina in an extended display mode?

Does Apple TV support wireless connection to the MacBook Pro retina display in an extended display mode? What is the output resolution and is sound also transmitted across?

SB1983, by extended display do you mean mirror? All MBP since early 2011 support it if they are running OS X 10.8 Mountain Lion. The resolution will depend on your Apple TV (2 Gen is 720 and 3rd Gen 1080) and wifi, it will lose some quality but I find it minimal. It does also mirror the sound.
Jules

Does AVL table supports popin in WebDynpro ABAP

Hi,
Just a short question, does AVL table supports popin in WebDynpro ABAP?
I know that popin in supported in normal table in WD ABAP. Is this feature also available for ALV table?
Thanks
Yingzhi

Hi Yingzhi Liu,
Did you get any answers to this question?
I'm also trying the same where we need to show additional details for an ALV table row. Is it possible to have a table popin in ALV? We are on 2004s release and implementing Web Dynpro for ABAP.

Does my board support dualchannel?

Similar Messages

Maybe you are looking for