Does N2K-C2232PP-10GE supports SFP Transceiver 1000BaseSX ?
Dear All,
Does N2K-C2232PP-10GE supports SFP Transceiver 1000BaseSX ?
Ethernet111/1/1
Model: unavailable
Type (SFP capable): unknown
Speed: 1000,10000
Duplex: full
Trunk encap. type: 802.1Q
FabricPath capable: yes
Channel: yes
Broadcast suppression: no
Flowcontrol: rx-(off/on),tx-(off/on)
Rate mode: dedicated
Port mode: Routed,Switched
QOS scheduling: rx-(8q1t),tx-(1p8q1t)
CoS rewrite: yes
ToS rewrite: no
SPAN: yes
UDLD: no
MDIX: no
TDR capable: no
Link Debounce: yes
Link Debounce Time: yes
FEX Fabric: no
dot1Q-tunnel mode: no
EFP: no
Num Rewrites Allowed: 0
Pvlan Trunk capable: yes
Port Group Members: none
EEE (efficient-eth): no
PFC capable: yes
Breakout capable: no
Thanks
For future users, as the question is couple months old.
http://www.cisco.com/c/en/us/products/collateral/switches/nexus-2000-series-fabric-extenders/data_sheet_c78-507093.html
Table 5. Cisco Nexus Fabric Extender Transceiver Specifications
-Kenny
Similar Messages
-
N2K-C2232PP-10GE and SFP-FC8G-SW
Hi
We install our new Storage and we would like to connect it trough our Nexus 2k infrastructure, so our question is very simple:
Is it possible to do it trough the SFP-FC8G-SW in the N2K-C2232PP-10GE? Are they compatible and can we configure the Ports for it?
To do it trough FCoE is not applicable, 'cos the HBAs for it are to expansive.
Thank you in advance for your support.
Kind Regards from SwitzerlandHi,
See this link:
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/release/notes/Rel_5_0_3_N2_1/Nexus5000_Release_Notes_5_0_3_N2.html#wp374982
Cisco Nexus 2000 Series
Cisco Nexus B22HP FEX1
N2K-B22HP-P
X
Cisco Nexus 2232TM FEX
N2K-C2232TM-10GE
X
Cisco Nexus 2232PP FEX
N2K-C2232PP-10GE
X
X
X
X
Cisco Nexus 2248TP FEX
N2K-C2248TP-1GE
X
X
X
X
Cisco Nexus 2224TP FEX
N2K-C2224TP-1GE
X
X
X
X
Cisco Nexus 2148T FEX
N2K-C2148T-1GE
X
X
X
X
Expansion Modules
16-port Universal GEM
N55K-M16UP(=)
X
X
N5596 Layer 3 GEM
N55K-M160L3(=)
X
X
N5548 Layer 3 daughter card
N55-D160L3(=)
X
X
16-port SFP+ Ethernet
N55-M16P(=)
X
X
X
X
8- 10 Gigabit Ethernet and 8- 10 Gigabit FCoE ports
N55-M8P8FP(=)
X
X
X
X
Transceivers
Fabric Extender Transceivers
Fibre Channel
8-Gbps Fibre Channel—short wavelength
DS-SFP-FC8G-SW(=)
X
X
X
X
8-Gbps Fibre Channel—long wavelength
DS-SFP-FC8G-LW(=)
X
X
X
X -
Does WS-C6704-10GE support WS-F6K-DFC4-AXL?
Hi guys,
I'm a bit confused here.
Here it says that you can upgrade WS-C6704-10GE with DFC4-AXL http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/hardware/Config_Notes/OL_24918.pdf (Table 2)
But here WS-C6704-10GE is not listed as compatible with DFC4-AXL http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/hardware/Module_Installation/Mod_Install_Guide/6500-emig/0adtrcrd.pdf (Table A2)
Also I was unable to add WS-F6K-DFC4-AXL to WS-C6704-10GE in the configuration tool.
I would be grateful if anyone could shed some light on it.No, you need to tell me the model of your supervisor card. Why does this matter, let me explain:
6704 is a 4-port line card that can push up to 40 Gbps. ideally, you'll find this line card with the Sup720. Installed together into a 6500 chassis, the Sup720 can support a 40 Gbps backplane which a 6704-10G can easily push at wire rate (non-blocking).
Now, enter a Sup2T. Stick the Sup2T into a 6500 chassis and the Sup2T can potentially move 80 Gbps of backplane. So, why would anyone want to buy a line card that can push 40 Gbps and push it into a chassis with 80 Gbps backplane. Doesn't make any sense. -
Cisco Nexus 5548UP support SFP-10G-LRM ?
Hi all, I have a question about Cisco Nexus 5548UP. Is Cisco Nexus 5548UP support SFP-10G-LRM ? Because in CCW, i can't configure the SFP-10G-LRM. There is only SFP-10G-LR, SR, and the others, but there's no LRM. Pelase help me to answer this question. Thanks a lot
The LRM is s special case transceiver which supports 10 Gbps over older FDDI grade multimode fiber when used with a mode conditioning patch cord. It is not supported on the Nexus 5548UP.
The SFP-10G-LR is used with single mode fiber for spans up to 10 km in length. It is supported on the 5548UP (and most every platform of Cisco's that takes SFPs).
Please see the product data sheet here. -
Does the 6600GT-VTD128 support video capture?
Hi,
I recently purchased an MSI 6600GT-VTD128 video card. The product information seems to suggest that the card has video input capabilities, and there is an adapter that plugs into the card that has a number of connections, one of which is labeled S-Video in. However, I haven't been able to get any video capture to work.
Does the card actually support this functionality? If not, what are the video input connections for? If so, is there some documentation as to how to set it up?
So far, I tried installing the video capture drivers that come with the card. I checked the manual. I checked the MSI web site FAQs. And I searched the forums.
Any help would be greatly appreciated.
Thanks,
DanielThanks Richard. Yes I do have a breakout cable like that. Actually, I described it in my original message. So, I am guessing from your message that you believe that the card should have the capability to capture video.
In my original message, I asked if there was any documentation on setting up the card for video capture. The manual does not describe the procedure, nor does the MSI web site.
There are drivers on the CD that claim to be for video capture, but they had no effect when I installed them. In fact, there appears to be no way to tell whether the drivers were actually installed successfully.
If anyone out there has successfully used this card for video capture, please let me know. -
I have the oringinal ipad, it does not seem to support ios6 and will not connect to itunes, WHY is this?
Start here... http://www.apple.com/support/iphone/assistant/itunes/
-
Does Photoshop CC not support touch on Windows 8.1 tablet?
Does Photoshop CC not support touch on Windows 8.1 tablet? Stylus nor finger working on canvas. Have all the updates from Windows and Adobe.
Photoshop does not have touch support. however some touch devices drivers have features the can be set to Photoshop Functions. For example
Tablets that have drivers that use Wintab API for pen support can be used with Photoshop Brush Pen support. Tablets that use Microsoft Ink API for pen support can not be used with Photoshop for Adobe does not have support for Microsoft INK API for Adobe states the INK API lack features used by Photoshop Brush engine. -
Does Sender Mail Adapter support "PayloadZipBean" module
Hi everyone,
I have a scenario where, I get the email with an zip file as an attachment and I need to extract this file and send across. There is no mapping transformation done here, only I need to forward the attached file to the file server.
Zip file always contains 1 file and is a text file.
so Its an Email to File Scenario.
Can I send the zip file as it is without unzipping i.e., send the attachment as iit is to the file server?
If I want to unzip the file, does the module "PayloadZipBean" support in case of sender mail adapter. ?
Thanks,
VarunHi Varun,
Use "PayloadZipBean " Module at Receiver Communication Channel in the Module Tab Set the "Module Key.mode = unzip"
and Receiver communication Channel file should be "FileName.txt".
http://help.sap.com/saphelp_nw2004s/helpdata/en/bd/c91241c738f423e10000000a155106/frameset.htm
Regards,
Naga. -
Get an Error window, The source folder does not contain any supported camera raw files
I am using CS2 and it would not open up my latest RAW files, I was getting a warning Could not complete your request because it is not the right kinds of document. So, I checked the Camera Raw Plug-in and it says Version 3.7. I see that my camera an Olympus E-20 is supported. But it is not opening the Raw files, the day before I took jpeg and they have opened. I will not trash my Adobe Photoshop CS2 because it was a royal pain to install and I don't know where the CD is.
I installed the latest DNG Converter and when I try to open up the folder which has all the RAW images that didn't open in Adobe, I still get an Error window that says, "The source folder does not contain any supported camera raw files." Why? It says it supports my Olympus E-20. I actually have the E-20n, I don't think that is the problem. My RAW icons usually show up as small image thumbnails and this time they are gray icons only with the incorrect date under the icon. Is there another product I can use without spending money? These images I took in RAW were special and I don't want to lose them. Please help!
EstherHello, I was using only CS2 with my Olympus E-20n for 5 years, no problem. It just started acting up in RAW this year. I downloaded Picasa that same day and now it seems to be opening up all of my RAW files that didn't open the other day. So, I think Picasa installed a new plug-in adaption to CS2 because now all my RAW icons have a new logo on them, the same one that's in Picasa. Strange, but it works now and I am not complaining anymore. I love CS2 and the many ways I can adjust RAW files, so I am using it, Picasa is a sideline now that I can take a look at many thumbnails and it organized all my photo files by the year and folders. Amazing free software. I have probably 60,000 images in my computer and an external hard drive and Picasa picked them all up and made a library, cool.
-
Does 10.5.6 Support Dual displays for Radeon 9800 Pro Mac Edition cards?
Does 10.5.6 Support Dual displays for Radeon 9800 Pro Mac Edition cards?
And is there driver updates for anyone using the all-in-ones HP printers...has anyone been able to use their scanners since the update? and has the dual screen support been added to avoid the blue screen on startup?The ATI Radeon 9600 PC/Mac edition 256 MB should work in the MDD G4. It has two DVI ports (one is dual-link and can support a 30" display). You will need adapters for ADC displays.
-
Does K8D Master-FT support Dual core Opteron?
Hi,
Does K8D Master-FT support dual core Opteron? I saw the latest BIOS was released at 2003/12/11 and said to support for all series of AMD Opteron(up to 248, SC, 2.2GHz/1M).
Thx, XuekunSorry I only looked after his question.
The entire K8D-Master3 series has support for it: >>Link<< -
Does Toshiba Multimedia Center support 5.1 via optical out?
Hello, I have a question before I buy this...
Does Toshiba Multimedia Center support 5.1 via optical out?
I can find this out anywhere they only mention digital out but that could be coax.
Can any of you help me?
ThanksHi
As far as I know the Toshiba Media Center supports these feature:
Dolby Digital Surround, Dolby Digital 5.1, EAX ADVANCED HD
_Ports:_
1 x LAN - RJ-45
4 x hi-speed USB - USB Typ A, 4-polig
1 x audio *SPDIF output*
1 x audio - line-In stereo port 3.5 mm
1 x headphones audio output stereo port 3.5 mm
Greats -
Does PSE 13 (Mac) support arranging pictures by EXIF Date-Time Taken?
Does PSE 13 (Mac) support arranging pictures by EXIF Date-Time Taken?
If not, is this an option under consideration?billqaz a écrit:
Does PSE 13 (Mac) support arranging pictures by EXIF Date-Time Taken?
If not, is this an option under consideration?
It's the default sort order. You can choose chronological order( ascending or descending) or by Import batch or by filename. Contrary to older versions, those sort orders are available not only in thumbnail view, but also in Folders view and albums. In albums you can sort as you like 'custom order'. No difference in Mac or Win. -
Does Final Cut Express support ProRes 1080p?
Does Final Cut Express support ProRes 1080p?
Hi(Bonjour)!
ProRes codecs was introduced with Final Cut Studio 2.
You can't create a ProRes sequence in FCE, but if you've installed the +Apple ProRes QuickTime Decoder 1.0 for Mac+ you will be able to import ProRes footage, but rendering or conversion will be needed.
http://support.apple.com/downloads/AppleProRes_QuickTime_Decoder_1_0_forMac
Michel Boissonneault -
Why the f**** does ios6. Not support YouTube on iPad 2? This is ridiculous if I would have known I would've never updated... I'm livid
YouTube is not now part of iOS 6. However, you can download the YouTube app at http://itunes.apple.com/app/youtube/id544007664.
See this similar post https://discussions.apple.com/thread/4335468?tstart=30
Cheers, Tom
Maybe you are looking for
-
How enter prise search works in sharepoint 2010
In my organization enterprise search is configured , -- sharepoint farm has -- two index servers ( share point server search service is configured in this servers) two web front end servers(sharepoint foundation web applications, and share point s
-
I updated firefox. When I did there was a circle with a slash (as in No!) across the firefox icon. I clicked on it to open the browser and the error message reads: the application firefox cannot be launched - 10661 How do I go to the previous version
-
My iMac did install new yosemite 10.10.3 telling me that new Photo app was "best ever" but now I can't open old iPhoto library because it was in old format of iPhoto library and the iPhoto app was now unusable because new Photo app. Can you help me!!
-
How to upgrade from Win 8.1 w/ Bing to Win 8.1 Professional
Hello, I just purchased an HP 400-413 Desktop PC from Best Buy and it came with Win 8.1 w/ Bing. I would like to upgrade to Windows 8.1 Professional. Can i simply purchase an upgrade license to unlock the professional features like Joining a Domain a
-
Mapping constant values to the target data source columns
Hi A Target data source has only two columns(RPT_NAME, RPT_LEVEL) and both of them are constants and mapped as follows WITH TEMP1 AS (select 'AS' as A from dual union select 'IS' as A from dual union select 'ED' as A from dual select t.A as RPT_NAME,