Does not boot only beep error code 4-3-4-3 Model: M55 MT-M 8810-W8T

Have a M55 MT-m 8810-W8T that does not display.
Power i suppose is OK as it powers up and give beep code of 4-3-4-3. From what I found it is a PHOENIX BIOS Q3.07 OR 4.X version. From searching I can only find that it means that "Boot code was read OK'. After the beep code I still have no display. Have tried on-board VGA (without the PCIe videocard). Tried the PCIe videocard, different memory, reset CMOS ......but still cannot get to the BIOS not boot into Windows.
So what does that exactly mean and how do I get the PC to boot up fully?
Thanks for any help in advance.

That usually means a memory error. Remove all of the memory and install one stick in the first slot. I have also overcome this error by "cleaning" the contacts of the memory module with the eraser of a pencil. Gently "scrub" the gold contacts at the botton of the DIMM, completely remove any residue and re-seat the module. It is possible you are mixing high and low density ram which could cause a situation like this.

Similar Messages

IMAC does not boot, only beeps. Video attached

Hello:
I am trying to figure out why an iMAC does not boot properly.
Memory:1GB (only 1 module in one of the 2 available slots).
Everytime I push the power button I only hear a sound and that's it.
You can hear the HDD spinning but the screen is always black.
Please find the sound that the iMAC makes everytime I turn it on:
http://www.youtube.com/watch?v=duRTB3iDZEU
Keboard does not respond so I cannot use things like press a key when turning on the computer, etc.
Mouse light is ok.
I am a newbie with MAC's so excuse me if I'm not doing something right.
Thanks

Hello robertin75
Check the ram, if the module has gone bad, has become dislodged or not fully seated in the slot then the iMac will only beep indicating an error and will not startup.
http://support.apple.com/kb/HT2341
I'm not exactly sure which model iMac you have and so it's hard to give specific instructions, but if you check in the User's Guide that came with it you will find the instructions for replacing and installing ram in your model.
If you no longer have the User's Guide you can find out by using the the following link.
http://support.apple.com/kb/HT1463
or the next one if it happens to be a newer glossy screen aluminum model.
http://support.apple.com/kb/HT1758
Dennis

TS1424 I download movies and when I reach the full size, like 4.01 GB for an HD movie, it does not say "done" but Error Code= -36

I download movies and when I reach the full size, like 4.01 GB for an HD movie, it does not say "done" but Error Code= -36

What do you think about turning File Vault off?
I'd first make a copy or backup of that Home folder first, then I'd never use Filevault again.
Is it possible the disk could be failing but Disk Utility not pick anything up?
Yes, DU just checks Directory structure, and not all that well at that, it is possible that there are bad blocks/sectors on the HD right where that Home Folder is located.
And finally, where is a good place to find interpretations of those cryptic error codes?!
For error -36, might try this...
http://docs.info.apple.com/article.html?artnum=301580
Well, in pure Apple File System talk... -36 ioErr I/O error (bummers)
Not very helpful, but generally means a Drive quit being Readable or Writable since starting the operation...
http://fuzzy.wordpress.com/2006/12/10/ioerror-36/
Terminal for one...
Find error code...
/usr/bin/grep "36" /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/CarbonC ore.framework/Headers/MacErrors.h
Or open this file in Text Edit if you have it...
System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/CarbonCor e.framework/Versions/A/Headers/MacErrors.h

There was a recent upadate on my PC, however it does not work. A error code comes up which says, min version is not compatible with max version. And I caanot open my browser. Please help.

I do a system restore which allows me to open my browser. Without this I cannot open my browser - the error code comes up every time.

Do a clean (re)install
* Download a fresh Firefox copy from http://www.mozilla.com/firefox/all.html and save the file to the desktop.
* Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
* Don't remove personal data when uninstalling.
* It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
From https://support.mozilla.com/en-US/questions/764376

The update does not work. An error code appears U44M1P2003

la mise a jour ne se fait pas. J'ai un code d'erreur U44M1P2003
Message was edited by: vincenth2012

See the following:
http://forums.adobe.com/message/4193333#4193333

HT4061 I have an iphone 5s, does not boot, blinking white screen with black logo, when trying itunes restore from mac and pc, error code 4013 which is usb error, any ideas?

I have an iphone 5s, does not boot, blinking white screen with black logo, when trying itunes restore from mac and pc, error code 4013 which is usb error, any ideas? Does a totally dead battery have that effect? I have had it plugged in to a computer overnight, but maybe does not charge when totally dead?
Please help, thanks in advance all1

Hi eggroll77,
Welcome to Apple Support Communities.
That alert codes does suggest there is a USB related issue. If you haven’t already, try the troubleshooting suggestions in the article linked below.
iOS: Restore errors 4005, 4013, and 4014
I hope this helps.
-Jason

Satellite C850-1NU does not boot Win 8.1 - Error Code 0xc0000098

Windows 8.1 will not boot
Laptop is *Toshiba Satellite C850 1NU*, as from Saturday it will not boot up!
*Error states "The boot configuration Data File doesn't contain valid information for an operating system.*
*File:\ BCD*
*Error Code 0xc0000098*
I have transferred recovery tools from another laptop to a USB stick and then enter bios of the Toshiba Laptop to make the USB drive to boot first.
It then comes up with the recovery tools.
I clicked on "Refresh your pc" it then reports "The drive where Windows is installed is locked. Unlock the drive and try again".
I clicked on "Reset your pc" it then reports "Unable to reset your pc. A required drive partition is missing".
I have also tried "Automatic Repair" and it reports "Repair couldn't repair your PC".
I am at a loss as to get my sons laptop up and running again. Advice would be much appreciated. Thank you.

Further to my question, *I have now resolved the issue.*
Thanks to phanlon7 on this link
[http://answers.microsoft.com/en-us/windows/forum/windows_8-system/windows-crash-refresh-hard-drive-locked-unlock/a6bb04ff-5dba-4e10-a849-644cd0851bc6?page=2&rtAction=1390385080363]
I used a usb stick and copied recovery from another windows 8 laptop.

Satellite Pro A100-080 does not boot - stays dark after 3 beeps

Hello,
after one week off, the Toshiba Satellite Pro A100-080 (PSAASE-00G004GR, 4 GB RAM) of my children does not boot anymore.
When powering on the system, it *beeps 3 times* (one longer, two short beeps), then the HDisk light shortly blinks "blue" and then nothing more happens. A/C, Power and Batterie LEDs are "blue", which seem to be the OK state.
No other useful help, as the display stays dark.
We had upgraded to 4 GB MEM (Kingston) one year ago and I already tried the former used 1 GB (included when purchased) or the 2 x 1 GB replacement from December 2007, but same status with those modules. So it is not
a defect memory.
I hope it is not the mainboard, probably only the included NVIDIA GeForce Go 7600 graphics adapter?
Does anyone have an idea, what might be the issue?
Thx for a short help.

Hello
Generally speaking this kind of beep codes are hardware related or with other words hardware is malfunctioning. So I think its a hardware problem and an ASP should check your notebook to identify the reason of this.
On the Toshiba website you will find a list of ASPs:
http://eu.computers.toshiba-europe.com > Support & Downloads > Find an authorized service provider

HT4790 My Mac OS Lion 10.7 FileVaulted HD does not boot, prohibitory sign, stop sign appears some minutes after boot starts. Disk Utility repair shows four error messages: Unable to bootstrap transaction group 2517: inconsistent crosscheck (the same with

My Mac OS Lion 10.7 FileVaulted HD does not boot, prohibitory sign, stop sign appears some minutes after boot starts. Disk Utility repair shows four error messages:
Unable to bootstrap transaction group 2517: inconsistent crosscheck
No valid commit checkpoint found
The volume xxxxxxxxxxxxxx(here it shows physical volume number) was found corrupt and can not be repaired.
Problems were encountered during repair of the partition map
Error: Storage system verify or repair failed.
(the same with 2518, 2519 and 2520 transaction group)
I suppose it is serious bug in Mac OS Lion managing FileVault and wonder what the help could be?

Most likely culprit is your Lacie drives which are notorious for flaky power supplies which cause just the sort of erratic behaviour that you describe. Have had similar issues myself. Lacie has been good about replacing my power converter-- twice. If you have seven of them, good luck finding the bad one or more. Like I said, the behaviour is erratic. Sometimes it'll work sometimes not. I can't comment on Samsung drives because I've never used them and have never heard anything about them. Same with Softraid. Why not just use Disk Utility. Sounds like you're ready for an external hardware raid. This will be much faster, much more reliable, and may even be cheaper than seven firewire drives. Check out G Tech, and Maxx Digital for starters.
Best of luck
Terry

Does anyone know what this error code means?My itunes will not open, no matter how many times i downlaod and restore it??? "The procedure entry point xmlITexTextReaderName could not be located in the dynamic link library libxml2.dlll."

Does anyone know what this error code means?My itunes will not even open, no matter how many times i downlaod and restore it??? "The procedure entry point xmlITexTextReaderName could not be located in the dynamic link library libxml2.dlll." Please let me know if your know anything! It is greatly apprecitated!

Taken at face value, you're having trouble with an Apple Application Support program file there. (Apple Application Support is where single copies of program files used by multiple different Apple programs are kept.)
Let's try something relatively simple first. Restart the PC. Head into your Add or Remove Programs control panel, select "Apple Application Support", click "Change" and then click "Repair".
If no joy after that, try the more rigorous uninstall/reinstall procedure from the following post. (Although the procedure is for Vista and 7 and you've got XP, just read "Computer" as "My Computer", read "Uninstall a program control panel" as "Add or Remove programs control panel" and assume the system is 32-bit, and you'll be doing the right things.)
Re: I recently updated to vista service pack 2 and I updated to itunes 10.2.1 and ever since I did that my itunes won't open any more. Itunes starts but before anything loads a

I have a printer xerox 3220 on networking ,have pc´s and a mac ,problem:it´s already install but does not work ,only print many page with code program,i will appreciate the solution

i have a printer xerox 3220 on networking ,have pc´s and a mac ,problem:it´s already install but does not work ,only print many page with code program,i will appreciate the solution

Hi guillermospain,
Welcome to the Support Communities!
The article below may be able to help you with this.
Click on the link to see more details and screenshots.
OS X: Connecting a Wi-Fi printer to your Wi-Fi network
http://support.apple.com/kb/ht3500
OS X Mountain Lion: Set up a printer
http://support.apple.com/kb/PH11145
OS X Mountain Lion: Reset the printing system
http://support.apple.com/kb/PH11143
Cheers,
- Judy

New system does not boot properly

I just set up a new system with:
a MS-6728 Neo2 FIS2R Mobo,
1gb Geil PC-3500 RAM (2x512),
2.6C proc.
2 Maxtor 120gb IDE drives RAID 0 with the onboard promise controller.
Lite-On DVD burner
ATI radeon 9800 video card
Enermax 300 watt power supply with:
3.3v - 28amp
5v - 30amp
12v 22amp
170watt total 3.3/5 combined
My problem is that my system NEVER boots up normally. It always freezes in the bios startup. The D-bracket stops at almost every possible combination of led's, which according to the manual the problems were: Testing RTC, Initialize Video interface, Testing memory, Initializing floppy controller, Memory detection, Decompressing bios to ram, possibly more. Sometimes I also just get beeping, either a continuous beep or 8 beeps. A few times it would display the bios startup screen, but halfway down would be gibberish characters and would be locked up. When I then turn the computer off then on again, the bios is reset at least somewhat(i know because I usually disable the full screen image on startup) and says memory timings are too tight, and I have the choice to enter bios or hit any key to automatically fix things. If I hit any key it will boot up ok. However when I restart/turn off the computer, the next time it again does not boot. I tried upping the ram voltages from 2.5-2.9v, and that seems to stay that way in the bios, even when it resets itself. Everything else is set to auto/slow. If I try to manually adjust the memory timings, even to the slowest possible settings, it does not boot, and I must turn it on/off a few times till the bios resets again, with the boot process stopping at one of the possiblilitys mentioned above. Using the info tab on speedfan, I got the memory info, and it displayed the voltage at 2.5v, not sure what that means but it is strange.
What I have already attempted:
I sent back the ram and got a new set, which hasn't changed anything. The first time the other ram failed memtest, this time it passed(for about 2 hrs). So I don't think its the ram.
I borrowed an antec truepower 430w powersupply, which had no effect.
I went back to bios version 1.3 from 1.9, which also seems to have no effect.
I was hoping to overclock the system a bit and enable performance mode etc etc, but now I'll be happy to just not have to go through a song and dance everytime I restart the computer. This is only the second computer I have built from scratch, and the first with raid, but that seemed to all go ok. Please help me diagnose the problem!

I too am having problems with my system.
865PE Neo2-FIS2R
2 Maxtor 120GB S-ATA drives, RAID 0, Promise
2 512MB Geil Ultra CL2-3-3-6
HP CD-RW
What IDE settings are you using?
E.g...Native? P-ATA Only...all of those settings
For me...sometimes XP will install and boot...but eventually system is unstable and XP crashes and corrupts itself...Event Manager errors different each time
Someone mentioned problems with Maxtor and AMI BIOS...anything I should keep in mind?
Sorry about all the different questions. I'm sure exactly where my problem lies. MSI thinks it may be my memory AND/OR on-board IDE controller since I can't get the on-board Intel RAID setup to consistently "see" and setup my RAID drives...even when it has worked...XP doesn't like the Intel configured RAID drives. Also tried just one S-ATA drive through on-board Intel and Promise. Next I will try a plain old IDE Hard Drive...no S-ATA...and make sure my memory passes memtest86+ testing.
Any other gems you can offer for this config??? Thanks.

T60 does not boot with Intel T7600G CPU

I replaced my Intel Core Duo T2400 with Intel Core 2 Duo T7600G CPU in ThinkPad T60(1951-CTO) laptop. However, laptop does not boot with Intel Core 2 Duo T7600G CPU. It doesn't even complete the POST: https://db.tt/8UL8FlE0 As seen in the video, I plugged in the power adapter at 0:02 and pressed the power button at 0:06. One can hear a little click made by optical device. If I press the power button again at 0:16, this click does not happen. BIOS version is 2.27. I have reset the BIOS settings by disconnecting the CMOS battery, but this didn't help. Once I replace the T7600G with my old T2400 then I'm able to boot the laptop.
Any ideas what might cause such behavior? Shouldn't there be beep codes in case of CPU issues? What else to try?

TuuS wrote:
600X wrote:
Since you came from a T2400, does your T60 even have a Rev. 3 motherboard? If it does not, then no Core 2 Duo will work, only Core Duo's.
I don't claim to be the top authority on T60 motherboards, but I believe any will use a Core 2 T7600, 7400, 7200 if the firmware is updated.
My own experience mirrors what TuuS has stated. I have yet to see a T60/p from any walk of life with a recent BIOS that will bark at a proper Core 2 Duo CPU.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Crystal Server 2013: How to troubleshoot "Can not create temp file---- Error code:-2147215357"

We have a Java7 web app, which generate PDF report by calling Crystal Server 2013 SP4.
The app is being deployed on many different servers. We sometimes got the error below when generating report:
com.crystaldecisions.sdk.occa.report.lib.ReportSDKException: Can not create temp file---- Error code:-2147215357 [CRSDK00000615] Error code name:internal
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.controllerExportInternal(PrintOutputController.java:280)
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.export(PrintOutputController.java:152)
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.export(PrintOutputController.java:130)
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.export(PrintOutputController.java:113)
Problem is, this seems to be a pretty generic exception. It could be caused by many different reasons.
e.g. network connection problem, wrong DB login, wrong folder path, lack of folder access right, etc.
Each time we could only guess what's wrong.
We are running into it again, and this time everything seems correctly configured so far.
We wonder if there are more info we can get to troubleshoot? For example, any log file of Crystal Server we should look into? Or does Crystal Server has debug mode which prints more details to tell us what goes wrong?

Prithviraj Shekhawat wrote:
Hi Henry,
I believe you are using RAS SDKs to export the reports to PDF.
Apply trace on RAS server and check what you find in RAS logs.
Check whether you can see timeout error is RAS logs. Usually if connection is lost and the RAS server no more have the session to write to the temp directory, we do see these errors.
Also, does the account that runs RAS have permissions to create a file in RAS's default temp directory? Are you getting any out of memory or out of disk space exceptions on App server or RAS, tracing RAS server is the way to move forward.
Thanks,
Prithvi
>>I believe you are using RAS SDKs to export the reports to PDF.
Yes
>>Apply trace on RAS server and check what you find in RAS logs.
>>Check whether you can see timeout error is RAS logs.
How to configure tracing, and where are RAS logs? Is it configured in CMC --> Servers --> Crystal Report Services?
>>Also, does the account that runs RAS have permissions to create
>>a file in RAS's default temp directory?
Pretty sure yes.
>> Are you getting any out of memory or out of disk space exceptions
>>on App server or RAS, tracing RAS server is the way to move forward.
Not on App server.
For RAS, that's the problem, I am not sure where to look.......

HP Z620 does not boot when external Seagate hard drive is connected

I'm troubleshooting an HP Z620 workstation with 32GB RAM, one 500GB HDD + one 1TB HDD running Win 7 Enterprise 64 bits, this user has 2 external USB 3.0 HDDs, one Buffalo 2TB + one Seagate Desktop Backup Plus 4TB; the problem comes when the external Seagate HDD is connected and the PC is turned one, for some reason the PC does not boots, it shows a message that states "Non-disk or no boot disk error" and sometimes it tries to boot, but then goes thru the "Windows repair option" or "Start Windows normally" routine, none of these results on starting the PC.
The only way this PC starts and works properly is when PC is started with the external Seagate HDD disconnected and then connected once the Win 7 is up and running; the problem described above does not happens with the external Buffalo 2TB HDD and the Seagate HDD have been tested throughly and no errors or problems have been detected on it.
I'll really appreciate your attention to this, as well as your prompt response.
Regards,
Gaspar Campos

Hi:
You may also want to post your question on the HP Business Support Forum -- z Workstations section where there may be more folks familiar with that issue.
http://h30499.www3.hp.com/t5/Workstations-z-series-xw-series/bd-p/bsc-272#.U1k4uv1OXGg

Does not boot only beep error code 4-3-4-3 Model: M55 MT-M 8810-W8T

Similar Messages

Maybe you are looking for