Does registration with verisign use hostid
Hi,
I'm looking to move a system that runs WebLogic AS, and has an SSL certificate
with Verisign, to a new machine. The question is, what is used by WebLogic to
identify the machine to VeriSign and the users, in the SSL negotiation. If the
identifier will be the machine's IP address of it's host-name, that's not a problem,
as the new hardware will have the same ones as the old machine. However, if the
machine's hostid (on most Unix systems, 'uname -i' on HP), which is the machine's
hardware unique id, is used, then I will have to get a new certificate from Verisign.
This is used to be tied to the IP-address, and later to the machine's MAC address,
but newer machines have this tied to the CPU (as in the case with Itanium-based
machines) or somehow to the motherboard.
I'd appreciate any input on the matter.
Thanks,
Raz
Hi Saurabh,
The L2FM is Layer2 Feature Manager which manages the mac-address table and mac-address
registrations and deletions from the hardware table. The L2FM component exists on Nexus
7K. In case of Nexus 5500 and Nexus 6K, there is an equivalent component called FWM. Since
most of the code is re-used in Nexus 6K platform, the references to L2FM need to be
removed/resolved on Nexus 6K code. There is a software bug to fix these L2FM references in
the code. Still the bug is in assigned state, hence the fix for this bug is not yet
available. You can safely ignore these messages, they have no impact. The mac-addresses
are registered with FWM and since there is no L2FM these messages have no impact.
========================================
CSCum82485 Nexus 5500/6000: L2FM messages seen
Symptom:
In a Nexus 6000 switch running NX-OS 7.0(0)N1(1), messages such as following can be seen
%ADJMGR-3-MAC_REG_FAILED: adjmgr [3745] Mac registration with L2FM failed for mac
002a.6a35.b341, iod Vlan250, phy iod: Gateway Port-Channel1:186
%ADJMGR-3-MAC_REG_FAILED: adjmgr [3745] Mac registration with L2FM failed for mac
00d0.03eb.2000, iod Vlan60, phy iod: Ethernet131/1/15
Conditions:
Usually seen when a host comes online.
Workaround:
L2FM is not a valid component on Nexus 6000. These are cosmetic messages and can be
ignored.
HTH
Inayath
***Plz rate the post and mark the thread as closed******
Similar Messages
-
What Encoder Settings Does "Share with Facebook" Use?
With iMovie '11 you can Share/Facebook, which will upload the current project to a Facebook personal page. The problem is, I need to upload the movie to a group page that I administer. Yes, this has been asked before, and the answer was "Export to a local drive/desktop and upload to your Facebook group." Got it.
BUT... USING WHAT ENCODER SETTINGS? When you upload directly to Facebook, it's a "black box"--all you can choose is resolution. The video is beautiful when it's finished uploading. But, I HAVE NO IDEA what those encoder settings are and I've tried about every other combination of MP4/H.264 and the video looks typically like dog excrement--never as good as when I upload with the Facebook option.
What encoder settings does the Facebook option use???
- George -If you want to replicate the black box, use SHARE/EXPORT MOVIE...
You can also use SHARE/MEDIA BROWSER. YOu will find the resulting movie buried in the project package.
If you want to roll your own...
SHARE/EXPORT TO QUICKTIME
QuickTime Movie
h.264 as video codec.
AAC or uncompressed as audio codec.
Set keyframes to automatic (or 24).
Set bitrate to 16,000 kbps, but you can back off from there. You may go as low as 8,000 but you would have to experiment.
It is difficult to get better quality than the default settings, but some people are able to get similar quality at a reduced file size. With YouTube and FaceBook, you should not care about file size. I would err on the side of quality, because FaceBook and YouTube may recompress in their proprietary format, and you want to give them as much to work with as possible.
If you want more detail, here is an article from YouTube on how to optimize settings. The same should work fine for FaceBook.
http://support.google.com/youtube/bin/static.py?hl=en&page=guide.cs&guide=172858 5&topic=1728570 -
How does one continue to use Mail on the early MacBook Pro, Model 1,1, that is not upgradable to Lion? I have been running iCloud on my iPhone (OS5) and iMac (Lion) along with the MacBook Pro (OS Version 10.6.8) since November until now. Mail will no longer download on the MacBook Pro and keeps asking for my password.
Mail should still be usable with your machine - but you'll need to update the settings to conform to the requirements of your system. Check with your ISP (like ATT, etc.) for the settings that will work with your Mail. Once you've updated this, you should be able to email like before.
For example, my ISP required that I go to Mail Preferences/Accounts and make sure the details conform to your email settings.
I have no idea of what your ISP is or what the settings might be, but this is likely the source of the problem. -
Can I add my digital copy movie to my iTunes with out using the disk, my gateway laptop/netbook does not have a disk drive I have the unused code and everything, I just can't stuck the movie into the computer itself and my desktop computer has no internet on it. Is there a way to add my movie to my iPod touch 2nd generation tuning 4.2.1
Hiya!
It depends on what kind of digital copy you have. This article goes ino details regarding the two types, and depending on the type you have, you may or may not need the DVD to redeem the code.
Transferring video from DVDs with iTunes digital content
http://support.apple.com/kb/HT1539
I hope this helps! Best wishes and good luck! -
I have a ipad 2 and it does not connect with safari using 3G
I have a ipad 2 and it does not connect with safari using 3G
Sorry to hear you are having issues, but there are 2 ways you can print from that device.
The first one is to simply email photos or documents to your printers email address by attaching them to a new message.
The other option is to download the HP ePrint Home and Biz app from Google Play. The app is free and should allow you to print pictures and documents to the printer with ease. I have added a link below on how to get started with this app.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01616126&lc=en&cc=us&dlc=en&product=3857218
Jon-W
I work on behalf of HP
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
Click the KUDOS STAR on the left to say “Thanks” for helping! -
is there a way to get photos off of a thumb drive onto something that can be uploaded to the ipad. I am doing away with my windows systems and using the ipad exclusively?
iPad Photo Recovery: How to Recover Deleted Photos
http://www.iskysoft.com/iphone-data-recovery-mac/ipad-photo-recovery.html
How to Restore Lost or Deleted Files from iPad
http://www.iphone-ipad-recovery.com/recover-ipad-mini-files.html
How to Recover Deleted Files from iPad
http://www.kvisoft.com/tutorials/recover-deleted-files-from-ipad.html
How to Recover Photos from iPad
http://www.ipubsoft.com/idevice-tips/recover-deleted-photos-on-ipad-mini.html
iSkysoft Free iPhone Data Recovery
http://www.iskysoft.com/iphone-data-recovery/
Recover iPhone/iPad/iPod touch lost data, Free.
Free recover iPhone/iPad/iPod touch lost contacts, photos, videos, notes, call logs and more
Recover data directly from iPhone or from iTunes backup
Preview and recover lost iOS data with original quality
Wondershare Dr.Fone for iOS
http://www.wondershare.net/data-recovery/iphone-data-recovery.html?gclid=CJT7i9e 6gb4CFcvm7AodbUEAJQ
Recover contacts, messages, photos, videos, notes, call history, calendars, voicemail, voice memos, reminders, bookmarks and other documents.
iPad Data Recovery Software (PC & Mac)
http://www.anysoftwaretools.com/ipad-data-recovery.html
Jihosoft Mobile Recovery for iOS
http://www.fonerecovery.com/iphone-data-recovery.html
Cheers, Tom -
By default, does AME render an AE project with the "use no proxies" setting?
By default, does AME render an AE project with the "use no proxies" setting? I use lots of proxies in my files and I want to make sure they are being ignored when I'm rendering in AME.
Adobe Media Encoder encodes After Effects compositions using their current appearance. There is no control the appearance of the composition, with one exception; there is no equivalent to the Render Settings controls in the After Effects Render Queue. If you want proxies to be used, or not, set up your composition for the desired configuration before you encode in Adobe Media Encoder.
The exception to this rule is Guide Layers. In Adobe Media Encoder, right-click on an After Effects composition and choose Source Settings, from this dialog you can control whether or not the Guide Layers in the composition are rendered. -
I have a version 1 iPad. I would like to be able to use my LCD projector to display content to my students. I have the dongle to attach to the projector, but can't make it work. The process DOES work with my friend's iPad 2. Any advice? Thanks!
Expanding on what deggie said, with an iPad 1 the app you're using must support video out. Only the iPad 2 can mirror the screen. The apps included with the iPad that output to external monitors are given here:
http://support.apple.com/kb/HT4108
For third-party apps, consult the app's documentation or contact the developer.
Regards. -
Apple iPAD 2. Needs password to unlock iPAD; however there is a permanent keyboard displayed on the screen that does not respond to touch. iPAD switches on with button but does not turn off using it at moment. Can you help please?
Try a reboot by holding both the power and home buttons until the apple logo appears, ignore the red slider if that appears. See if that clears the glitch.
-
Does anyone of you use a HD-camcorder like Canon Legria HF G10 and cut films with Final Cut Express 4.0.1. I did not buy this product yet but ask before. Now I have 4GB RAM and i5 MacBooK Pro. Do any problems exist using FCE having made films with this camera?
I save the films als QuickTime films (mov) and create DVDs with iDVD.
Will the data be too many if I make films with such a camera (HD) so that 1 hour of film cannot be burned to one DVD (or if is not necessary to film with such a good quality because in iDVD the film looses its quality?).I was able to find this info regarding the camera:
AVCHD 1080/50i. 1080/25P (Maximum AVCHD 24Mbps)
Recording Modes
MXP 24Mbps / FXP 17Mbps / XP+ 12Mbps / SP 7Mbps / LP 5Mbps
The 1080/50i (interlaced) modes will work with FCE. PAL in this case. 60i is NTSC.
Al -
A recent update of Firefox included the OpenH264 Video Codec. This software is made by Cisco Systems Inc. They are a known military contractor of the U.S Department of Defense, who helps the U.S. government spy on everyone. Every single piece of software that comes from this company is suspect and should be considered malware and spyware. About a month ago I posted a question asking why Mozilla was doing business with them and asked how to remove it completely from my computer. The only response I got was a bot response explaining how to disable it, which I made clear was not enough. There was no no explanation given as to why they were doing business with a company like Cisco. I'm sure that if more Firefox users were aware of these facts they would be just as concerned as I am. I'm still waiting to hear back from Mozilla on this issue. They apparently consider the issue close. I do not.
Guess I'm royally screwed since my Cable Modem is made by Cisco. Anyway, they are using it to play HTML5 videos encoded in H.264 on operating systems that do not have the codec: http://en.wikipedia.org/wiki/OpenH264
Might look at this thread for how to get rid of it: http://forums.mozillazine.org/viewtopic.php?f=38&t=2888681 -
What bluetooth protocol does the iPod Touch use with a keyboard?
Hi...
Say, does anyone know what bluetooth protocol apple is using for their bluetooth keyboards for the iPhone and iPod Touch? It is probably HID, but the people at RIM (i.e. BlackBerry) use SPP. So I would think many 3rd party keyboards use SPP (Serial Port Protocol). But, then, there are many posts about "I wish Apple would support SPP" because people want to build apps that interface with external HW that only supports SPP.
What I want to do? (you ask)
I've one of these nice / expensive Think-out-side portable folding keyboards (good). That only has a serial interface (bad). There are many bluetooth "dongles" out there with serial ports (good). But they only support SPP or Serial Port Protocol (bad? maybe? depends).
See, I know RIM (BlackBerry) people support SPP on their devices. But I haven't heard (found) word one about what the iPod Touch supports. I would hate to spend $80 on one of these dongles and find out it doesn't work.
So, what does the iPod Touch use when talking to the bluetooth keyboard?
-thanksFrom page 37 of iOS 4.1 Touch Users Guide:
Using an Apple Wireless Keyboard
For ease of typing, you can use an Apple Wireless Keyboard (available separately;
iPod touch 3rd generation or later).
Regarding the original questions, the BT profiles supported by the Touch arelisted here:
http://support.apple.com/kb/HT3647 -
Trouble doing FaceTime with iPad 2 using email address. Please help?
I have an iPhone 4S my wife also has an iPhone 4S
I have iPad 2 as well.
While at home connected to the same wifi source
I am able to do FaceTime video chat with each phone just by dialing the number of the other phone
I am able to do FaceTime connection from iPad2 by dialing either one of the phone numbers
However if I try to do FaceTime with iPad2 using the registered email account
it says busy call back
I went to work and connected my iPhone to another wifi
I tried FaceTime with with the iPad2 using the registered email it says myphone or iPad is busy
Both the iPhones and the iPad2 have the same registered email address
Even if I enter an alternate eamil address in iPad2 it still says my phone or iPad is2 busy call back
iphone 2 iphone using same wifi ok
ipad to iPhone using the same wifi ok
ipad to iPhone with each using different wifi it is still ok
however iphone to Ipad using the registered email address it is not going through
whether the ipad is connected to the same wifi or different wifi
Any suggestions
IndyramFigured it out
Here are some tips
If you want to Facetime using email address with another apple device
be it iPhone or iPad each individual device has to have a unique email address
You can have the same ID for billing purposes but for FaceTime connection
it has to have different email addresses
In Settings select Facetime and make sure you have different email addresses
If not you will get a busy signal
To connect to an iPad you have to use the email address assigned to the facetime of that iPad
To connect to the iPhone you can use either email address or the phone number
Hope this will help some one
Ram -
Mac registration with L2FM failed
My Logfile on Nexus 6K is fiilled with Logs like below:
Nexus Version is: 7.0(3)N1(1)
2014 Sep 12 14:49:11 Nexus-6K %ADJMGR-3-MAC_REG_FAILED: adjmgr [3727] Mac registration with L2FM failed for mac xxxx.xxxx.xxxx, iod Vlan191, phy iod: port-channel169
2014 Sep 12 14:49:24 Nexus-6K %ADJMGR-3-MAC_REG_FAILED: adjmgr [3727] Mac registration with L2FM failed for mac xxxx.xxxx.xxxx, iod Vlan108, phy iod: port-channel91
2014 Sep 12 14:49:36 Nexus-6K %ADJMGR-3-MAC_REG_FAILED: adjmgr [3727] Mac registration with L2FM failed for mac xxxx.xxxx.xxxx, iod Vlan108, phy iod: port-channel91
2014 Sep 12 14:49:58 Nexus-6K %ADJMGR-3-MAC_REG_FAILED: adjmgr [3727] Mac registration with L2FM failed for mac xxxx.xxxx.xxxx, iod Vlan191, phy iod: port-channel169
Cisco's document does not explain what is causing this:
Error Message: AM-3-MAC_REG_FAILED Format: Mac registration with L2FM failed for mac %s, iod %s, phy iod: %s
Explanation MAC registration with L2FM failed.
Recommended Action No action is required.
Here is my Logging Configuration:
logging level aaa 5
logging level cdp 6
logging level copp 6
logging level flogi 5
logging level hsrp 6
logging level interface-vlan 5
logging level lldp 5
logging level monitor 6
logging level radius 5
logging level session-mgr 6
logging level spanning-tree 6
logging level track 6
logging level virtual-service 2
logging level igmp 3
logging event link-status default
logging logfile messages 6
logging server x.x.x.x use-vrf x facility syslog
logging monitor 6
Can anyone tell me what are these and how to stop them from occurring. Also would appreciate suggestions on how can I improve logging configuration.Hi Saurabh,
The L2FM is Layer2 Feature Manager which manages the mac-address table and mac-address
registrations and deletions from the hardware table. The L2FM component exists on Nexus
7K. In case of Nexus 5500 and Nexus 6K, there is an equivalent component called FWM. Since
most of the code is re-used in Nexus 6K platform, the references to L2FM need to be
removed/resolved on Nexus 6K code. There is a software bug to fix these L2FM references in
the code. Still the bug is in assigned state, hence the fix for this bug is not yet
available. You can safely ignore these messages, they have no impact. The mac-addresses
are registered with FWM and since there is no L2FM these messages have no impact.
========================================
CSCum82485 Nexus 5500/6000: L2FM messages seen
Symptom:
In a Nexus 6000 switch running NX-OS 7.0(0)N1(1), messages such as following can be seen
%ADJMGR-3-MAC_REG_FAILED: adjmgr [3745] Mac registration with L2FM failed for mac
002a.6a35.b341, iod Vlan250, phy iod: Gateway Port-Channel1:186
%ADJMGR-3-MAC_REG_FAILED: adjmgr [3745] Mac registration with L2FM failed for mac
00d0.03eb.2000, iod Vlan60, phy iod: Ethernet131/1/15
Conditions:
Usually seen when a host comes online.
Workaround:
L2FM is not a valid component on Nexus 6000. These are cosmetic messages and can be
ignored.
HTH
Inayath
***Plz rate the post and mark the thread as closed****** -
My Ipad mini does not see my printer. my wife's ipad2 does. We both use IOS8 and upgraded at the same time. How can I remedy this?
OK great info!
I found 2 possible ethernet to USB adapters:
By "Plugable": USB 2.0 to ethernet LAN wired network adapter - seems this will work, but I'll contact Plugable.
2. Apple USB Ethernet Adapter
Easily connect your MacBook Air computer to an Ethernet network with the Apple USB Ethernet Adapter. Small and light, it connects to the USB 2.0 port of your MacBook Air and provides an RJ-45 connector that supports 10/100BASE-T performance. BUT NOT SURE IF THIS WILL WORK ON ANYTHING BUT a MacBook Air…
One person commented:
This little gem used to be the device of choice for adding a second Ethernet interface to a Mac Mini Server and I'd been using one that way for about a year. After doing a software update to 10.6.6 it stopped working. Forewarned is forearmed – it appears that Apple is finally enforcing the MacBook Air system requirement.
Thanks for any additional comments.
Best regards,
Steve Schulte
Sunday 6 January 2013
Maybe you are looking for
-
Oracle 8.1.6 and 8.1.61 ODBC Driver Access Violation
Using Oracle ODBC for Windows to Oracle 8.1.6 database to get a list of the tables/views in the database. The following code worked on 8.0.4, 8.0.5, and 8.1.5 databases and their respective ODBC Drivers. It gives me an access violation with 8.1.6. Th
-
TS3276 sent items are no longer indexed, how to solve it?
Sent messages are put in the map "sent" but are not displayed well. Only expeditor and subject are shown correctly. The content of mail or discussion is not correct, it comes from former emails related to another subject... quite ennoying. I guess th
-
Soft Buttons not appearing on the 525G (UC520)
Hi, We have installed a 525G2 on a clients phone system (UC520, Version 15.1(4)M60). The handset is working, in that it can make and receive calls. However there are no soft buttons displaying on the screen. It has been configured with a template for
-
hi guys..! plz can anyone explain the output of the code below... public class AQuestion public void method(Object o) System.out.println("Object Version"); public void method(String s) System.out.println("String Version"); public static void main(Str
-
Presentation on career and training
Dear All, We are implementing ESS/MSS mySAP2005 Bussiness packages with Portal 7.0. Also, upgraded the 4.6c to ECC 6.0. We have succefully deployed Bussiness packages using sdm. In 4.6c ITS, there were Training and skills applications which allows to