Does Test Unknown indicate a problem in output from showboards -a
My customer is worried about this "Unknown" status and I cannot find a good explanation.
This is an M5000 SUN Server
XSCF> showboards -a
XSB DID(LSB) Assignment Pwr Conn Conf Test Fault
00-0 00(00) Assigned y n n Passed Normal
00-1 02(00) Assigned y n n Unknown Normal
00-2 01(02) Assigned y y y Passed Normal
00-3 03(02) Assigned y y y Passed Normal
01-0 01(00) Assigned y y y Passed Normal
01-1 03(00) Assigned y y y Passed Normal
01-2 01(01) Assigned y y y Passed Normal
01-3 03(01) Assigned y y y Passed Normal
Moderator Action:
Post has been moved from the Solaris 10 discussion space,
to the Server HARDWARE discussion space, for proper topic alignment.
You aren't using Solaris when you connect via the XSCF.
This is strictly a hardware configuration question and I would guess that it is explained in either the XSCFReference Manual
https://docs.oracle.com/cd/E19867-01/E21466-01/E21466-01.pdf
else in the M5000 System Administration Guide
https://docs.oracle.com/cd/E19867-01/E21618/E21618.pdf
for that platform.
Similar Messages
-
Does anyone know how to convert the output from the standard report to xml?
Does anyone know how to convert the output from the standard SAP report to xml?
since it a standard report which you cannot modify you can only do the following.
submit report exporting list to memory
then
list from memory and then
use the returned itab along with CALL TRNSFORMATION key word to convert to xml.
but this only going to place the whole list content (including data and formating lines,etc) into a xml element and not the actual data alone in the list . -
Help Does these figures indicate a problem
Hi
Been on Infinity 1 a few months and was getting speed of 36 Mbps download and 8 Mbps up.
Now getting 25 Mbps and 5 Mbps, not very pleased about this as I am quite close to the exchange.
I got the figures off the Hub and some of the figures don't look right, too me at least!!
Can you give me an idea if they mean anything?
1. Product Name: HomeHub5
2. Serial number: +076284+1444003981
3. Firmware version: v0.07.01.0235-BT (Type B) Last updated [Unknown]
4. Board version: 01
5. VDSL uptime: 0 days, 01:24:19
6. Data Rate: 5997 / 27397
7. Maximum Data Rate: 6393 / 50579
8. Noise Margin: 6.3 / 13.8
9. Line Attenuation: 0.0 / 21.6
10. Signal Attenuation: 0.0 / 0.0
11. Data sent/received: 42.4 MB / 747.3 MB
12. Broadband username: [email protected]the bottom half will detach if you remove the 2 screws and the inner part with MK3 on it can also be removed without removing any more screws.
is it the backplate that is loose - the plate which is screwed to the wall? if so you need engineer back or have you tried just tightening the screws which hold backplate to wall box?
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’. -
How can I test the SCORM 2004 compliant based output from captivate
Hi everyone,
I have created a SCORM 2004 compliant based output file from Captivate itself. Before sharing it with client, I want to check that whether it is compliant or not.
Is there any tool to check the compliance check in LMS? I am new to this, please suggest and help...
Regards
Vikas SharmaHi RodWard,
I have tested the zip on scorm cloud and it worked well. Also shared it with the client. But client came back with a question that -
"SCORM Pacakage does not report partial completion. When a person stops training, we have the progress bar to indicate that they are at 0, 25, 50, 75 or 100%. So the SCORM pkg is inadequate. "
Now, I am facing an issue in doing these particular settings inside SCORM 2004 in captivate.
Note that, the captivate file is not a questionnaire and its a video with few animations and a player on which it is running.
Can you please guide me...
Regards
Vikas Sharma -
PCI Problem - no output from rear
Hi, I'd be most grateful if anyone can help me.
I have an old Sound Blaster PCI soundcard. Currently I have a set of 2.0 speakers hooked up from the Line Out (green) jack and have no problems with them.
I would like to run a second set of speakers from the Rear Out (black) jack to another room. But when I try to connect any powered speakers (even switching the existing line out speakers to the rear out) to the rear out there is no output whatsoever. The documentation that came with the card says that you should be able to run powered speakers from both the line out and rear out.
Am I missing something obvious?
Once again, thanks for any help in advance.can you be more specific on what soundcard type you've...
i mean a old pci one are a lot...and what's old, a month or 6 yrs(3-pole or 4-pole on out2&3)...
more info needed of type.
p.s. 2nd &3th channels are with creative drivers effect channels , clear sound (or 2/0) is only on the line out. the 2 & 3 do have effects depending on setup(eax/dolby/ etc. etc.) and so it's not nice to listen to only 2nd(or 3th) channel when you're listen to music/movie. you can better take the rec out of the amplifier that's connected to the soundcard.
so something like:
soundcard lineout - linesignalwire - amplifier tape/in - amplifier tape/out - linesignalwire - amplifier tape/in - etc. etc..(loop amps by their ins & outs like tape/cassette -deck connections, see manual amps for setting switches correctly(LOL hardwareconfiguration of hifi). then you got in every room 2/0 stereo of your lineout.Message Edited by www_96KHz_tk on 05-3-2005 02:59 AM -
Problem with output from report to excel, calling the report from form 10g
Hi everyone, I'm having a problem generating a excel from a report, which is called from a form, I'm using Forms 10g. The problem is this: My report has a variable number of columns. These columns appear according to data obtained from the database, these columns are dates, In vesion 6 excel file generated shows the columns one after another starting in column A1 to column CP. I mean that the dates are correlative. But in version 10g the excel file generated shows the same report starting in column A to column T, only shows the 20 dates correlative corresponding to this columns, the rest of the dates are down the excel sheet in groups of 20 dates, it's something, the file in 6i grows across and in 10g grows down the excel sheet. The report (rdf file) is the same in 6i and 10g, I compiled the 6i version to obtain the 10g version. The excel sheet generated in 10g looks like the report was in pdf format, because PDF format, cuts the report in pages and the file grows down, if I generate the report in PDF format it has the same structure excel file in 10g has. I hope yo can help because I have days trying to solve this but I have no succes. If someone could help I could email the excel files generated in two versions. Here I put the code I use to generate the files in 6i and 10g. I have tried with DESFORMAT=SPREADSHEET in 10g but the result is the same. Thanks for your help. Greetings for all.
Code for version 6i (Works Very well)
PROCEDURE GUARDAREXCEL IS
pl_id ParamList;
nom_rep varchar2(20);
cla_rep varchar2(20);
cod_dis varchar2(4);
nom_arch varchar2(100);
fec date;
BEGIN
pl_id := Get_Parameter_List('tmpdata');
IF NOT Id_Null(pl_id) THEN
Destroy_Parameter_List( pl_id );
END IF;
pl_id := Create_Parameter_List('tmpdata');
IF :BK_PARAMETROS.LI_COD_DIS IS NOT NULL THEN
cod_dis := :BK_PARAMETROS.LI_COD_DIS;
END IF;
IF :BK_PARAMETROS.TI_COD_CLI IS NOT NULL THEN
Add_Parameter(pl_id,'P_COD_CLI',TEXT_PARAMETER,:BK_PARAMETROS.TI_COD_CLI||'%');
ELSE
Add_Parameter(pl_id,'P_COD_CLI',TEXT_PARAMETER,'%');
:BK_PARAMETROS.TI_COD_CLI:='%';
END IF;
IF :BK_PARAMETROS.CLAS_REP=1 THEN
cla_rep := '001';
ELSE
IF :BK_PARAMETROS.CLAS_REP=2 THEN
cla_rep := '002';
ELSE
IF :BK_PARAMETROS.CLAS_REP=3 THEN
cla_rep := '003';
ELSE
cla_rep := '004';
END IF;
END IF;
END IF;
Add_Parameter(pl_id,'P_COD_DIS',TEXT_PARAMETER, cod_dis);
Add_Parameter(pl_id,'P_FECHA',TEXT_PARAMETER,to_char(:BK_PARAMETROS.FECFIN, 'DD/MM/YYYY'));
Add_Parameter(pl_id,'P_CLASE',TEXT_PARAMETER, cla_rep);
Add_Parameter(pl_id,'PARAMFORM',TEXT_PARAMETER,'NO');
Add_Parameter(pl_id,'DESTYPE',TEXT_PARAMETER,'File');
Add_Parameter(pl_id,'MODE',TEXT_PARAMETER,'Character');
Add_Parameter(pl_id,'DESFORMAT',TEXT_PARAMETER,'DELIMITED' );
select sysdate into fec from dual;
IF :BK_PARAMETROS.TIPO_REP=1 THEN
BEGIN
nom_rep := 'tdvenrli1577.rep';
nom_arch := 'c:\windows\temp\RepCobranzaPlanos' || TO_CHAR(fec, 'ddmmyyyy') || '.xls';
END;
ELSIF :BK_PARAMETROS.TIPO_REP=2 THEN
BEGIN
nom_rep := 'tdvenrli1578.rep';
nom_arch := 'c:\windows\temp\RepCobranzaLargos' || TO_CHAR(fec, 'ddmmyyyy') || '.xls';
END;
ELSIF :BK_PARAMETROS.TIPO_REP=3 THEN
BEGIN
Add_Parameter(pl_id,'P_XLS',TEXT_PARAMETER, '1');
nom_rep := 'tdvenrli1576.rep';
nom_arch := 'c:\windows\temp\RepCobranzaDetallados' || TO_CHAR(fec, 'ddmmyyyy') || '.xls';
END;
ELSE
BEGIN
nom_rep := 'TDVENRLI1545.REP';
nom_arch := 'c:\windows\temp\RepCobranzaTodos' || TO_CHAR(fec, 'ddmmyyyy') || '.xls';
END;
END IF;
--Add_Parameter(pl_id,'DESNAME',TEXT_PARAMETER,nom_arch );
Add_Parameter(pl_id,'DESNAME',TEXT_PARAMETER, nom_arch);
standard.commit;
Run_Product(REPORTS, nom_rep, SYNCHRONOUS, runtime, FILESYSTEM, pl_id,'');
EXCEPTION WHEN Run_Product_Failure THEN
message('Error');
END;
Code for version 10g
PROCEDURE GUARDAREXCEL IS
pl_id ParamList;
nom_rep varchar2(20);
cla_rep varchar2(20);
cod_dis varchar2(4);
nom_arch varchar2(100);
fec date;
--byt12122007.sn
repid REPORT_OBJECT;
vURL VARCHAR2(500);
rep_status VARCHAR2(20);
vJobID VARCHAR2(100);
v_rep VARCHAR2(100);
VAR NUMBER;
w_name_repserv VARCHAR2(30);
--byt1212007.en
BEGIN
--w_name_repserv:=F_OBTIENE_SERVREP;
w_name_repserv:='repserv';
pl_id := Get_Parameter_List('mytmp_params');
IF NOT Id_Null(pl_id) THEN
Destroy_Parameter_List( pl_id );
END IF;
pl_id := Create_Parameter_List('mytmp_params');
IF :BK_PARAMETROS.LI_COD_DIS IS NOT NULL THEN
cod_dis := :BK_PARAMETROS.LI_COD_DIS;
END IF;
IF :BK_PARAMETROS.TI_COD_CLI IS NOT NULL THEN
Add_Parameter(pl_id,'P_COD_CLI',TEXT_PARAMETER,:BK_PARAMETROS.TI_COD_CLI||'%');
ELSE
Add_Parameter(pl_id,'P_COD_CLI',TEXT_PARAMETER,'%');
:BK_PARAMETROS.TI_COD_CLI:='%';
END IF;
IF :BK_PARAMETROS.CLAS_REP=1 THEN
cla_rep := '001';
ELSE
IF :BK_PARAMETROS.CLAS_REP=2 THEN
cla_rep := '002';
ELSE
IF :BK_PARAMETROS.CLAS_REP=3 THEN
cla_rep := '003';
ELSE
cla_rep := '004';
END IF;
END IF;
END IF;
Add_Parameter(pl_id,'P_COD_DIS',TEXT_PARAMETER, cod_dis);
Add_Parameter(pl_id,'P_FECHA',TEXT_PARAMETER,to_char(:BK_PARAMETROS.FECFIN, 'DD/MM/YYYY'));
Add_Parameter(pl_id,'P_CLASE',TEXT_PARAMETER, cla_rep);
Add_Parameter(pl_id,'PARAMFORM',TEXT_PARAMETER,'NO');
/*Add_Parameter(pl_id,'DESTYPE',TEXT_PARAMETER,'File');
Add_Parameter(pl_id,'MODE',TEXT_PARAMETER,'Character');
Add_Parameter(pl_id,'DESFORMAT',TEXT_PARAMETER,'DELIMITED' );*/
select sysdate into fec from dual;
IF :BK_PARAMETROS.TIPO_REP=1 THEN
BEGIN
repid := find_report_object('tdvenrli1577');
--nom_rep := 'tdvenrli1577.rep';
nom_arch := 'c:\windows\temp\RepCobranzaPlanos' || TO_CHAR(fec, 'ddmmyyyy') || '.xls';
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_FILENAME,'tdvenrli1577');
END;
ELSIF :BK_PARAMETROS.TIPO_REP=2 THEN
BEGIN
repid := find_report_object('tdvenrli1578');
--nom_rep := 'tdvenrli1578.rep';
nom_arch := 'c:\windows\temp\RepCobranzaLargos' || TO_CHAR(fec, 'ddmmyyyy') || '.xls';
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_FILENAME,'tdvenrli1578');
END;
ELSIF :BK_PARAMETROS.TIPO_REP=3 THEN
BEGIN
repid := find_report_object('tdvenrli1576');
Add_Parameter(pl_id,'P_XLS',TEXT_PARAMETER, '1');
--nom_rep := 'tdvenrli1576.rep';
nom_arch := 'c:\windows\temp\RepCobranzaDetallados' || TO_CHAR(fec, 'ddmmyyyy') || '.xls';
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_FILENAME,'tdvenrli1576');
END;
ELSE
BEGIN
repid := find_report_object('tdvenrli1545');
--nom_rep := 'TDVENRLI1545.REP';
nom_arch := 'c:\windows\temp\RepCobranzaTodos' || TO_CHAR(fec, 'ddmmyyyy') || '.xls';
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_FILENAME,'tdvenrli1545');
END;
END IF;
--Add_Parameter(pl_id,'DESNAME',TEXT_PARAMETER,nom_arch );
--Add_Parameter(pl_id,'DESNAME',TEXT_PARAMETER, nom_arch);
standard.commit;
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_DESNAME,nom_arch);
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_COMM_MODE, SYNCHRONOUS);
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_EXECUTION_MODE, RUNTIME);
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_DESTYPE, 'File');
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_DESFORMAT, 'DELIMITED');
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_SERVER, w_name_repserv);
SET_REPORT_OBJECT_PROPERTY(repid, REPORT_OTHER, 'paramform=no');
v_rep := RUN_REPORT_OBJECT(repid, pl_id);
rep_status := REPORT_OBJECT_STATUS(v_rep);
WHILE rep_status IN ('RUNNING','OPENING_REPORT','ENQUEUED') LOOP
rep_status:= report_object_status(v_rep);
END LOOP;
IF rep_status = 'FINISHED' THEN
vJobID := SUBSTR(v_rep, INSTR(v_rep, '_', -1)+1);
vURL:='/reports/rwservlet/getjobid'||vJobID||'?'||'server='||w_name_repserv;
END IF;
WEB.SHOW_DOCUMENT(vURL, '_blank');
IF NOT form_success THEN
MESSAGE('Error: PL/SQL held against Button failed to execute');
RAISE FORM_TRIGGER_FAILURE;
END IF;
/*Run_Product(REPORTS, nom_rep, SYNCHRONOUS, runtime, FILESYSTEM, pl_id,'');
EXCEPTION WHEN Run_Product_Failure THEN
message('Error');*/
END;There are two problems with your VI. First, the basic logic of writing/appending to a file (Excel, TDMS, anything) should go something like this: Open the file, position yourself at the end of the file, then, in the loop, acquire data and write it to the file until you are finished with data acquisition. When you exit the acquire/write to file loop, then close the file. In particular, the opening and the closing of the file should not be inside the loop.
As others have pointed out, writing to Excel might not be optimal, particularly if you are acquiring data at a high rate (and would therefore be writing a lot of data). We actually use Excel in our data acquisition routine, mainly reading from a WorkSheet to get the parameters of a particular stimulus, but also writing the outcome of the response to the stimulus. As it happens, our "acquisition rate" in this example is on the order of several samples per minute, so there's no problem using Excel (we also sample 16 channels of analog data at 1 KHz -- this gets written as a binary file).
Second, if you really do want to use Excel, use the (existing) Excel file to which you want to append as the "template" argument of the New Report function. Then use the Excel Get Last Row function to position yourself at "end of file", as noted above.
Good Luck.
Bob Schor -
My UR12 Steinberg interface is recognized by Yosemite but I can't get any output from the device, does anyone know how to fix this problem? Thanks in advance
Apparently it's related to the Firefox plug in.
This isn't exactly a solution but more of a way to avoid opening PDFs with Firefox's plug in.
1. Highlight "Tools" from the Menu Bar in the top left of the screen (or click "Options" if using the Firefox Compact Menu)
2. Select to "Options
3. Select "Applications"
4. Look for "Adobe Acrobat Document" under Content Type and to the right under Action select "Use Adobe Reader (default)" instead of the using Adobe Acrobat in Firefox
5. Open a test PDF. It should open in it's own window now.
Again, not a complete solution but something that'll at least let you scroll with PDFs open.
More info here: http://forums.mozillazine.org/viewtopic.php?f=38&t=2171033 -
iPod nano 6th generation, syncing with audiobooks does not work now, had been working. Sync test says: No iPod touch, iPhone, or iPad found. Connectivity test OK, no physical problems, iTunes shows the iPod. Any clues what to do?
Hmm.. Thank you for the response.
Have you tried using the iPod with another user account or computer, to help narrow down whether the problem lies with the computer, account, or the iPod itself?
Maybe try reformatting it, using the tools provided by Windows. Instructions on how to reformat your iPod can be found in this article.
http://www.methodshop.com/gadgets/ipodsupport/erase/index.shtml
B-rock -
Problem getting output in Excel
Hi!
I'm having problems with getting output in excel.
I generated report that gives me xml and it was ok.
Then I started concurrent to merge template and this xml and chosed Excel as output.
When I try to open it in IE all I'm getting is
End tag 'p' does not match the start tag 'a'. Error processing resource 'http://testserver.hlutrija.hr:8001/OA_CGI/FNDWRR.e...
<td class="c2"><p class="c8"><a name="Text35" id="Text35"><a name="Text34" id="Text34"><span cla...
When I try to view output from Firefox(it's more forgiving for incorrect xml then IE) it opened the whole document as a text (no xml, no excel but text - I saw that on a page info).
Anyway I realized that indeed generated xml wasn't correct since one <a tag wasn't closed.
But I tried to copy/paste to text editor and save as .xls file and it opened it OK.
But this certainly isn't the solution you would wan't to offer to a client.
On this instance XML is 5.0.
I tried bunch of things to make it open directly in Excel (I believe that then it wouldn't have any problems - ie when I used preview on defining template it offered me to open or save in Excel and I got what I wanted).
I tried to define Viewer Options (added applications/vnd.ms-excel for XML, HTML, Text Desc: Microsoft Excel), set the profile Viewer:Application for HTML/XML/Text to Microsoft Excel). But that didn't help either.
I even tried defining new Profile -> Viewer:Application for Excel based on similar Profiles. But this also didn't help.
Every time the result is the same both in IE(stops because of bad xml) and Firefox (I get bad xml recognized as text).
On another instance I have xmlp v 5.6.2
There I have some sample report and sample template.
When I there try to open output in Firefox once again I get xml recognized as text.
When I try to open in IE(7.0) I get a page that looks like html in browser.On the Page file menu I have option to edit in Excel. When I choose that it opens Excel but instead of this same page I only get: Authentication failed.
When I try to save this page it offers me only web formats (whole web page...). But nevertheless I tell it to save like test.xls. It saves ok. But when I try to open it. Excel starts but again all I get is: Authentication failed.
When I open this in text editor it has only:
From: <Saved by Windows Internet Explorer 7>
Subject:
Date: Thu, 30 Aug 2007 14:28:37 +0200
MIME-Version: 1.0
Content-Type: text/html;
charset="iso-8859-2"
Content-Transfer-Encoding: 7bit
X-MimeOLE: Produced By Microsoft MimeOLE V6.00.2900.3138
Content-Location: http://server.client.hr:8002/OA_CGI/FNDWRR.exe?temp_id=3132885517
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-2">
<META content="MSHTML 6.00.6000.16525" name=GENERATOR></HEAD>
<BODY><PRE>Authentication failed.
</PRE></BODY></HTML>
I really don't have any more ideas.
I've searched this forum, metalink, web, but nothing yet helped.
Can anyone help?Is your xml file being generated correctly?
For the request that you submitted, click the 'View Details' button. If the 'View XML' button is enabled, click that and it will open your XML in a new browser.
If it's not enabled, the request needs to be changed so its output is XML.
Not sure if this will help, but at least it will eliminate that there is anything wrong with the file or data.
Janel -
I'm thinking of upgrading from v10.6.8 Snow Leopard to OS X Yosemite. I know, I'm years behind, but it has become a necessity. My Mac is becoming slow and is incompatible with many softwares and websites. Does anyone know of any problems associated with this upgrade? What are the implications and/or consequences of installing Yosemite? Does it effect functionality of v10.6.8 software or hardware? Are there any precautions I should take before the installation? I have read some posts about Macs slowing right down after installing Yosemite. Any insights and information (in layman's terms please!) would be very useful. Thanks.
Huge thanks for your response Michel. I apologise for the delay in getting back to you. I have done as you suggested, the details are pasted below. Clearly there are some applications I need to remove and no doubt my HD could do with a 'spring clean'. My Mac 'Safe Booted' when I turned it on this morning.
I use many different softwares, some web-based. The decision to upgrade to OSX Yosemite is because I was unable to attend a Webinar this week using GoToMeeting downloadable software. GoToMeeting have upgraded their system and my OS is no longer supported. Other websites like VImeo no longer support my version of Safari. I tend to use Chrome if Safari isn't compatible.
Problem description:
I'm thinking of upgrading from v10.6.8 Snow Leopard to OS X Yosemite. However I have noticed that my MacBook Pro becoming ‘slow’ over the last 3 weeks and therefore might have some issues that need to be resolved before I even consider installing OSX Yosemite. Over the last week my Mac has Safe Booted on three occasions, so clearly there’s a ‘glitch’ occurring.
EtreCheck version: 2.1.1 (104)
Report generated 6 December 2014 10:21:01 GMT
Hardware Information: ℹ️
MacBook Pro (15-inch, Early 2011) (Verified)
MacBook Pro - model: MacBookPro8,2
1 2 GHz Intel Core i7 CPU: 4-core
4 GB RAM
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
AMD Radeon HD 6490M - VRAM: 256 MB
Color LCD 1440 x 900
Intel HD Graphics 3000 - VRAM: 384 MB
System Software: ℹ️
Mac OS X 10.6.8 (10K549) - Uptime: 0:35:42
Disk Information: ℹ️
Hitachi HTS545050B9A302 disk0 : (465.76 GB)
S.M.A.R.T. Status: Verified
- (disk0s1) <not mounted> : 210 MB
Macintosh HD (disk0s2) / : 499.76 GB (236.21 GB free)
HL-DT-ST DVDRW GS31N
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Microsoft Microsoft® Nano Transceiver v2.0
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple, Inc. MacBook Pro
Configuration files: ℹ️
/etc/launchd.conf - Exists
Adware: ℹ️
Geneio [Remove]
Kernel Extensions: ℹ️
/System/Library/Extensions
[not loaded] com.flipvideo.IOUSBCameraMassStorage (1.0.1) [Support]
[loaded] com.microsoft.driver.MicrosoftMouse (8.2) [Support]
/System/Library/Extensions/MicrosoftMouse.kext/Contents/PlugIns
[not loaded] com.microsoft.driver.MicrosoftMouseBluetooth (8.2) [Support]
[loaded] com.microsoft.driver.MicrosoftMouseUSB (8.2) [Support]
Startup Items: ℹ️
HWNetMgr: Path: /Library/StartupItems/HWNetMgr
HWPortDetect: Path: /Library/StartupItems/HWPortDetect
Startup items are obsolete in OS X Yosemite
Problem System Launch Daemons: ℹ️
[not loaded] org.samba.winbindd.plist [Support]
Launch Agents: ℹ️
[running] com.flipvideo.FlipShare.AutoRun.plist [Support]
[loaded] com.google.keystone.agent.plist [Support]
[running] com.trusteer.rapport.rapportd.plist [Support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Support]
[running] com.flipvideo.FlipShareServer.launchd.plist [Support]
[loaded] com.google.keystone.daemon.plist [Support]
[running] com.trusteer.rooks.rooksd.plist [Support]
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist [Support]
[failed] [email protected] [Details]
[invalid?] com.citrixonline.GoToMeeting.G2MUpdate.plist [Support]
[loaded] com.genieo.completer.download.plist Adware! [Remove]
[loaded] com.genieo.completer.update.plist Adware! [Remove]
User Login Items: ℹ️
None
Internet Plug-ins: ℹ️
o1dbrowserplugin: Version: 5.38.6.0 - SDK 10.8 [Support]
Google Earth Web Plug-in: Version: 7.1 [Support]
OfficeLiveBrowserPlugin: Version: 12.3.6 [Support]
RealPlayer Plugin: Version: Unknown
AdobePDFViewerNPAPI: Version: 10.1.12 [Support]
FlashPlayer-10.6: Version: 15.0.0.239 - SDK 10.6 [Support]
Flash Player: Version: 15.0.0.239 - SDK 10.6 [Support]
iPhotoPhotocast: Version: 7.0 - SDK 10.7
googletalkbrowserplugin: Version: 5.38.6.0 - SDK 10.8 [Support]
QuickTime Plugin: Version: 7.6.6
AdobePDFViewer: Version: 10.1.12 [Support]
CANONiMAGEGATEWAYDL: Version: 2.1.0.1 [Support]
CANONiMAGEGATEWAYLI: Version: 2.1.0.1 [Support]
EPPEX Plugin: Version: 3.0.5.0 [Support]
JavaAppletPlugin: Version: 13.9.8 - SDK 10.6 Check version
User internet Plug-ins: ℹ️
BrowserPlus_2.9.8: Version: 2.9.8 [Support]
CitrixOnlineWebDeploymentPlugin: Version: 1.0.105 [Support]
Safari Extensions: ℹ️
Omnibar Adware! [Remove]
My eBay Manager
Add To Amazon Wish List
Audio Plug-ins: ℹ️
iSightAudio: Version: 7.6.6
3rd Party Preference Panes: ℹ️
3ivx MPEG-4 [Support]
BrowserPlus [Support]
Flash Player [Support]
Microsoft Mouse [Support]
Perian [Support]
Trusteer Endpoint Protection [Support]
Time Machine: ℹ️
Time Machine information requires OS X 10.7 "Lion" or later.
Top Processes by CPU: ℹ️
26% Safari
2% WindowServer
2% activitymonitord
1% PluginProcess
0% WebProcess
Top Processes by Memory: ℹ️
405 MB WebProcess
301 MB Safari
125 MB Mail
116 MB rapportd
116 MB mds
Virtual Memory Information: ℹ️
1.02 GB Free RAM
1.78 GB Active RAM
429 MB Inactive RAM
1.07 GB Wired RAM
422 MB Page-ins
0 B Page-outs
Diagnostics Information: ℹ️
Dec 6, 2014, 09:45:53 AM Self test - passed
Dec 5, 2014, 11:49:18 PM QTKitServer_2014-12-05-234918_[redacted].crash -
My new IPad mini has poor wifi reception. It goes in and out. My IPod, Iphone4, Ipad1 and Ipad2 work fine. What can I do? Does anyone else have this problem?
The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
Cheers, Tom -
We have a SharePoint Enterprise 2013 system at RTM level. We've installed Workflow Manager 1.0 by following the steps at
http://technet.microsoft.com/en-us/library/jj658588.aspx. For the final step of Validating the Installation we created a simple list-level workflow and verified that the workflow
is invoked successfully. This is working successfully, but only for a single user. If other users in the same site collection try to invoke the workflow on this same list we get the ULS Log Error:
Claims Authentication af3zp Unexpected STS Call Claims Saml: Problem getting output claims identity. Exception: 'Microsoft.SharePoint.SPException: The specified user or domain group was not found. --->
System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated.
followed by:
Failed to issue new security token. Exception: Microsoft.SharePoint.SPException: The specified user or domain group was not found. ---> System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated.
(as details below).
All accounts that are attempting to use the Test Workflow (both working and non-working user accounts) are valid AD accounts and are included in the User Profile Sync that runs nightly. All have Contribute or Design permission level (and for testing,
Full Control).
What could cause the Claims Authentication to fail when certain users attempt to launch the workflow?
Thank you for your response.
Jim Mac.
08/29/2013 10:22:51.94 w3wp.exe (0x2020) 0x26D8 SharePoint Foundation
Claims Authentication af3zp Unexpected STS Call Claims Saml: Problem getting output claims identity. Exception: 'Microsoft.SharePoint.SPException: The specified user or domain group was
not found. ---> System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated. at System.Security.Principal.NTAccount.Translate(IdentityReferenceCollection sourceAccounts, Type targetType,
Boolean forceSuccess) at System.Security.Principal.NTAccount.Translate(Type targetType) at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKeyClaim(IClaimsIdentity claimsIdentity,
SPClaim loginClaim) --- End of inner exception stack trace --- at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKeyClaim(IClaimsIdentity claimsIdent... 94aa5c2d-fa45-9b83-b203-a92b20102583
08/29/2013 10:22:51.94* w3wp.exe (0x2020) 0x26D8 SharePoint Foundation
Claims Authentication af3zp Unexpected ...ity, SPClaim loginClaim) at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKey(String
encodedIdentityClaimSuffix) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.CreateTokenCacheReferenceFromTokenSignature(SPRequestInfo requestInfo, IClaimsIdentity identity) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.AugmentTokenCacheReferenceClaim(SPRequestInfo
requestInfo, IClaimsIdentity identity) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.AugmentOutputIdentityForRequest(SPRequestInfo requestInfo, IClaimsIdentity outputIdentity) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.GetOutputClaimsIdentity(IClaimsPrincipal
principal, RequestSecurityToken request, Scope scope)'. 94aa5c2d-fa45-9b83-b203-a92b20102583
08/29/2013 10:22:51.94 w3wp.exe (0x2020) 0x26D8 SharePoint Foundation
Claims Authentication fo1t Monitorable STS Call: Failed to issue new security token. Exception: Microsoft.SharePoint.SPException: The specified user or domain group was not found. --->
System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated. at System.Security.Principal.NTAccount.Translate(IdentityReferenceCollection sourceAccounts, Type targetType, Boolean forceSuccess)
at System.Security.Principal.NTAccount.Translate(Type targetType) at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKeyClaim(IClaimsIdentity claimsIdentity, SPClaim loginClaim)
--- End of inner exception stack trace --- at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKeyClaim(IClaimsIdentity claimsIdentity, SPClaim logi... 94aa5c2d-fa45-9b83-b203-a92b20102583
08/29/2013 10:22:51.94* w3wp.exe (0x2020) 0x26D8 SharePoint Foundation
Claims Authentication fo1t Monitorable ...nClaim) at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKey(String encodedIdentityClaimSuffix)
at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.CreateTokenCacheReferenceFromTokenSignature(SPRequestInfo requestInfo, IClaimsIdentity identity) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.AugmentTokenCacheReferenceClaim(SPRequestInfo
requestInfo, IClaimsIdentity identity) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.AugmentOutputIdentityForRequest(SPRequestInfo requestInfo, IClaimsIdentity outputIdentity) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.GetOutputClaimsIdentity(IClaimsPrincipal
principal, RequestSecurityToken request, Scope scope) at Microsoft.IdentityModel.Securi... 94aa5c2d-fa45-9b83-b203-a92b20102583
08/29/2013 10:22:51.94* w3wp.exe (0x2020) 0x26D8 SharePoint Foundation
Claims Authentication fo1t Monitorable ...tyTokenService.SecurityTokenService.Issue(IClaimsPrincipal principal, RequestSecurityToken request) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.Issue(IClaimsPrincipal
principal, RequestSecurityToken request) 94aa5c2d-fa45-9b83-b203-a92b20102583Hi Aries,
I am facing issue with work flow where Workflow goes to Suspend mode.
I am facing an issue with SP2013 Custom Workflow developed using Visual Studio 2012.
Objective of the Custom workflow: User fills the form and submit, list get updated and workflow will initiate and go for the process.
Issue: After the deployment of WF, for first time when user is filling the form and submit, list is getting updated. But the Workflow Goes to "Suspend" mode. (
This Custom Workflow has a configuration file where we are providing other details including ID of Impersonator (farm is running under Claim Based Authentication).
Work flow works fine once when the Impersonator initiate the workflow (Fill the form and submit for approval) and everything works fine after that.
Following steps are already performed
1.Make sure User profile synchronization is started.
2.Make sure the user is not the SharePoint system user.
3.Make sure the user by whom you are logged is available in User Profile list.
4.Step full synchronization of User Profile Application.
From the ULS logs it seems the user's security token from the STS service and User profile service is not being issued.
Appreciate any thoughts or solution.
Following are the log files.
<-------------------------------Information taken from "http://YYYY.XXXXX.com/sites/xxxx/_layouts/15/wrkstat.aspx" where it is showing workflow status as "Suspend"------->
http://yyyy.XXXX.com/sites/xxxx/_vti_bin/client.svc/sp.utilities.utility.ResolvePrincipalInCurrentcontext(input=@ParamUser,scopes='15',sources='15',inputIsEmailOnly='false',addToUserInfoList='False')?%40ParamUser='i%3A0%23.w%7CXXXXX%5Csps_biscomdev'
Correlation Id: f5bd8793-a53c-2127-bfb1-70bc172425e8 Instance Id: 14a985a0-60c8-42db-a42c-c752190b8106
RequestorId: f5bd8793-a53c-2127-0000-000000000000. Details: RequestorId: f5bd8793-a53c-2127-0000-000000000000. Details: An unhandled exception occurred during the execution of the workflow instance. Exception details: System.ApplicationException: HTTP 401
{"error_description":"The server was unable to process the request due to an internal error. For more information about the error, either turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug>
configuration behavior) on the server in order to send the exception information back to the client, or turn on tracing as per the Microsoft .NET Framework SDK documentation and inspect the server trace logs."} {"x-ms-diagnostics":["3001000;reason=\"There
has been an error authenticating the request.\";category=\"invalid_client\""],"SPRequestGuid":["f5bd8793-a53c-2127-8654-672758a68234"],"request-id":["f5bd8793-a53c-2127-8654-672758a68234"],"X-FRAME-OPTIONS":["SAMEORIGIN"],"SPRequestDuration":["34"],"SPIisLatency":["0"],"Server":["Microsoft-IIS\/7.5"],"WWW-Authenticate":["Bearer
realm=\"b14e1e0f-257f-42ec-a92d-377479e0ec8d\",client_id=\"00000003-0000-0ff1-ce00-000000000000\",trusted_issuers=\"00000005-0000-0000-c000-000000000000@*,[email protected]79e0ec8d\"","NTLM"],"X-Powered-By":["ASP.NET"],"MicrosoftSharePointTeamServices":["15.0.0.4420"],"X-Content-Type-Options":["nosniff"],"X-MS-InvokeApp":["1;
RequireReadOnly"],"Date":["Fri, 10 Apr 2015 19:48:07 GMT"]} at Microsoft.Activities.Hosting.Runtime.Subroutine.SubroutineChild.Execute(CodeActivityContext context) at System.Activities.CodeActivity.InternalExecute(ActivityInstance
instance, ActivityExecutor executor, BookmarkManager bookmarkManager) at System.Activities.Runtime.ActivityExecutor.ExecuteActivityWorkItem.ExecuteBody(ActivityExecutor executor, BookmarkManager bookmarkManager, Location resultLocation)
ULS Log
04/16/2015 15:22:03.70 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation Authentication Authorization agb9s Medium OAuth request. IsAuthenticated=False, UserIdentityName=, ClaimsCount=0 f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.70 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation Runtime ajd6k Verbose Value for isAnonymousAllowed is : False f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.70 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation Runtime ajd6l Verbose Value for checkAuthenticationCookie is : True f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.70 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8b Verbose Looking up context site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.70 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8b Verbose Looking up context site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation Monitoring b4ly Medium Leaving Monitored Scope (Request (GET:http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly)). Execution Time=18.7574119057031 f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8b Verbose Looking up context site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.71 w3wp.exe (0x1C74) 0x1AB8 SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.73 PowerShell.exe (0x29BC) 0x2B9C SharePoint Foundation General narq Verbose Releasing SPRequest with allocation Id {AF89E1D7-C47F-467B-8FD4-D7DC768820EE}
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8b Verbose Looking up context site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly.
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev.
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80.
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80.
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Monitoring nasq Medium Entering monitored scope (Request (GET:http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly)). Parent No
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8b Verbose Looking up context site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly.
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev.
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80.
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80.
04/16/2015 15:22:03.73 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Logging Correlation Data xmnv Medium Name=Request (GET:http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly) f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.74 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Monitoring nasq Medium Entering monitored scope (Application Authentication Pipeline). Parent Request (GET:http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly) f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.74 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8b Verbose Looking up context site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.74 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.74 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.74 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.74 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.75 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Claims Authentication ah25l Medium SPJsonWebSecurityBaseTokenHandler: ValidateActorIsSelfIssuer! Issuer '00000005-0000-0000-c000-000000000000' is not self
issuer. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.75 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Monitoring nasq Medium Entering monitored scope (Getting Site Subscription Id). Parent [S2S] Getting token from STS and setting Thread Identity f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.75 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8b Verbose Looking up context site
http://inetdev/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.75 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.75 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.75 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.75 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.75 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Monitoring b4ly Medium Leaving Monitored Scope (Getting Site Subscription Id). Execution Time=0.341314329055788 f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.75 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Monitoring nasq Medium Entering monitored scope (Reading token from Cache using token signature). Parent [S2S] Getting token from STS and setting Thread
Identity f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.76 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General ajji6 High Unable to write SPDistributedCache call usage entry. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.76 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Monitoring b4ly Medium Leaving Monitored Scope (Reading token from Cache using token signature). Execution Time=7.5931438213516 f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.76 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Application Authentication ajwpx Medium SPApplicationAuthenticationModule: Failed to build cache key for user f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.76 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Topology aeayb Medium SecurityTokenServiceSendRequest: RemoteAddress: 'http://localhost:32843/SecurityTokenServiceApplication/securitytoken.svc' Channel:
'Microsoft.IdentityModel.Protocols.WSTrust.IWSTrustChannelContract' Action: 'http://docs.oasis-open.org/ws-sx/ws-trust/200512/RST/Issue' MessageId: 'urn:uuid:fd5eba94-c39d-4667-89bd-089411c87f09' f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.77 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation Topology aeax9 Medium SecurityTokenServiceReceiveRequest: LocalAddress: 'http://c1vspwfe01.vitas.com:32843/SecurityTokenServiceApplication/securitytoken.svc'
Channel: 'System.ServiceModel.Channels.ServiceChannel' Action: 'http://docs.oasis-open.org/ws-sx/ws-trust/200512/RST/Issue' MessageId: 'urn:uuid:fd5eba94-c39d-4667-89bd-089411c87f09' f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.77 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation Monitoring nasq Medium Entering monitored scope (ExecuteSecurityTokenServiceOperationServer). Parent No f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation Claims Authentication ah25l Medium SPJsonWebSecurityBaseTokenHandler: ValidateActorIsSelfIssuer! Issuer '00000005-0000-0000-c000-000000000000' is not self
issuer. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation General narq Verbose Releasing SPRequest with allocation Id {F17590DF-49D9-439D-86BC-5AE6416BB765} f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation General 6t8b Verbose Looking up site
http://inetdev/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation General narq Verbose Releasing SPRequest with allocation Id {3847D5A4-15C6-4AF9-B062-E22BB555DF4F} f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Portal Server User Profiles ae0s1 High Identity claims mapped to '0' user profiles. Claims: [nameid: '', nii: 'windows', upn: '', smtp: '', sip: ''], User Profiles: f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Portal Server User Profiles ae0sr Unexpected UserProfileException caught.. Exception Microsoft.Office.Server.Security.UserProfileNoUserFoundException: 3001002;reason=The
incoming identity is not mapped to any user profile account in SharePoint. Possible cause is that no user profiles are created in user profile database. Contact your administrator. at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.GetSingleUserProfileFromClaimsList(UserProfileManager
upManager, IEnumerable`1 identityClaims) at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.<>c__DisplayClass2.<GetMappedIdentityClaim>b__0() is thrown. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Portal Server User Profiles ae0su High The set of claims could not be mapped to a single user identity. Exception 3001002;reason=The incoming identity is not mapped
to any user profile account in SharePoint. Possible cause is that no user profiles are created in user profile database. Contact your administrator. has occured. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation Claims Authentication ae0tc High The registered mappered failed to resolve to one identity claim. Exception: Microsoft.Office.Server.Security.UserProfileNoUserFoundException:
3001002;reason=The incoming identity is not mapped to any user profile account in SharePoint. Possible cause is that no user profiles are created in user profile database. Contact your administrator. at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.GetSingleUserProfileFromClaimsList(UserProfileManager
upManager, IEnumerable`1 identityClaims) at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.<>c__DisplayClass2.<GetMappedIdentityClaim>b__0() at Microsoft.SharePoint.SPSecurity.<>c__DisplayClass5.<RunWithElevatedPrivileges>b__3()
at Microsoft.SharePoint.Utilities.SecurityContext.RunAsProcess(CodeToRunElevated secureCode) at Microsoft.SharePoint.SPSecurity.RunWithElevatedPrivileges(WaitCallback secureCode, Object param) at Microsoft.SharePoint.SPSecurity.RunWithElevatedPrivileges(CodeToRunElevated
secureCode) at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.GetMappedIdentityClaim(Uri context, IEnumerable`1 identityClaims) at Microsoft.SharePoint.IdentityModel.SPIdentityClaimMapperOperations.GetClaimFromExternalMapper(Uri
contextUri, List`1 claims) f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation Claims Authentication af3zp Unexpected STS Call Claims Saml: Problem getting output claims identity. Exception: 'Microsoft.Office.Server.Security.UserProfileNoUserFoundException:
3001002;reason=The incoming identity is not mapped to any user profile account in SharePoint. Possible cause is that no user profiles are created in user profile database. Contact your administrator. at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.GetSingleUserProfileFromClaimsList(UserProfileManager
upManager, IEnumerable`1 identityClaims) at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.<>c__DisplayClass2.<GetMappedIdentityClaim>b__0() at Microsoft.SharePoint.SPSecurity.<>c__DisplayClass5.<RunWithElevatedPrivileges>b__3()
at Microsoft.SharePoint.Utilities.SecurityContext.RunAsProcess(CodeToRunElevated secureCode) at Microsoft.SharePoint.SPSecurity.RunWithElevatedPrivileges(WaitCallback secureCode, Object param) at Microsoft.SharePoint.SPSecurity.RunWithElevatedPrivileges(CodeToRunElevated
secureCode) at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.GetMappedIdentityClaim(Uri context, IEnumerable`1 identityClaims) at Microsoft.SharePoint.IdentityModel.SPIdentityClaimMapperOperations.GetClaimFromExternalMapper(Uri
contextUri, List`1 claims) at Microsoft.SharePoint.IdentityModel.SPIdentityClaimMapperOperations.ResolveUserIdentityClaim(Uri contextUri, ClaimCollection inputClaims) at Microsoft.SharePoint.IdentityModel.SPIdentityClaimMapperOperations.GetIdentityClaim(Uri
contextUri, ClaimCollection inputClaims, SPCallingIdentityType callerType) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.GetLogonIdentityClaim(SPRequestInfo requestInfo, IClaimsIdentity inputIdentity, IClaimsIdentity
outputIdentity, SPCallingIdentityType callerType) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.EnsureSharePointClaims(SPRequestInfo requestInfo, IClaimsIdentity outputIdentity, SPCallingIdentityType callerType)
at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.AugmentOutputIdentityForRequest(SPRequestInfo requestInfo, IClaimsIdentity outputIdentity) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.GetOutputClaimsIdentity(IClaimsPrincipal
principal, RequestSecurityToken request, Scope scope)'. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.78 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation Claims Authentication fo1t Monitorable STS Call: Failed to issue new security token. Exception: Microsoft.Office.Server.Security.UserProfileNoUserFoundException:
3001002;reason=The incoming identity is not mapped to any user profile account in SharePoint. Possible cause is that no user profiles are created in user profile database. Contact your administrator. at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.GetSingleUserProfileFromClaimsList(UserProfileManager
upManager, IEnumerable`1 identityClaims) at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.<>c__DisplayClass2.<GetMappedIdentityClaim>b__0() at Microsoft.SharePoint.SPSecurity.<>c__DisplayClass5.<RunWithElevatedPrivileges>b__3()
at Microsoft.SharePoint.Utilities.SecurityContext.RunAsProcess(CodeToRunElevated secureCode) at Microsoft.SharePoint.SPSecurity.RunWithElevatedPrivileges(WaitCallback secureCode, Object param) at Microsoft.SharePoint.SPSecurity.RunWithElevatedPrivileges(CodeToRunElevated
secureCode) at Microsoft.Office.Server.Security.UserProfileIdentityClaimMapper.GetMappedIdentityClaim(Uri context, IEnumerable`1 identityClaims) at Microsoft.SharePoint.IdentityModel.SPIdentityClaimMapperOperations.GetClaimFromExternalMapper(Uri
contextUri, List`1 claims) at Microsoft.SharePoint.IdentityModel.SPIdentityClaimMapperOperations.ResolveUserIdentityClaim(Uri contextUri, ClaimCollection inputClaims) at Microsoft.SharePoint.IdentityModel.SPIdentityClaimMapperOperations.GetIdentityClaim(Uri
contextUri, ClaimCollection inputClaims, SPCallingIdentityType callerType) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.GetLogonIdentityClaim(SPRequestInfo requestInfo, IClaimsIdentity inputIdentity, IClaimsIdentity
outputIdentity, SPCallingIdentityType callerType) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.EnsureSharePointClaims(SPRequestInfo requestInfo, IClaimsIdentity outputIdentity, SPCallingIdentityType callerType)
at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.AugmentOutputIdentityForRequest(SPRequestInfo requestInfo, IClaimsIdentity outputIdentity) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.GetOutputClaimsIdentity(IClaimsPrincipal
principal, RequestSecurityToken request, Scope scope) at Microsoft.IdentityModel.SecurityTokenService.SecurityTokenService.Issue(IClaimsPrincipal principal, RequestSecurityToken request) at Microsoft.SharePoint.IdentityModel.SPSecurityTokenService.Issue(IClaimsPrincipal
principal, RequestSecurityToken request) f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.79 w3wp.exe (0x0C48) 0x1318 SharePoint Foundation Monitoring b4ly Medium Leaving Monitored Scope (ExecuteSecurityTokenServiceOperationServer). Execution Time=17.1551132895382 f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.79 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Claims Authentication fsq7 High SPSecurityContext: Request for security token failed with exception: System.ServiceModel.FaultException: The server was
unable to process the request due to an internal error. For more information about the error, either turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug> configuration behavior) on the server in
order to send the exception information back to the client, or turn on tracing as per the Microsoft .NET Framework SDK documentation and inspect the server trace logs. at Microsoft.IdentityModel.Protocols.WSTrust.WSTrustChannel.ReadResponse(Message
response) at Microsoft.IdentityModel.Protocols.WSTrust.WSTrustChannel.Issue(RequestSecurityToken rst, RequestSecurityTokenResponse& rstr) at Microsoft.IdentityModel.Protocols.WSTrust.WSTrustChannel.Issue(RequestSecurityToken
rst) at Microsoft.SharePoint.SPSecurityContext.SecurityTokenForContext(Uri context, Boolean bearerToken, SecurityToken onBehalfOf, SecurityToken actAs, SecurityToken delegateTo, SPRequestSecurityTokenProperties properties) f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.79 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Claims Authentication 8306 Critical An exception occurred when trying to issue security token: The server was unable to process the request due to an internal
error. For more information about the error, either turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug> configuration behavior) on the server in order to send the exception information back to
the client, or turn on tracing as per the Microsoft .NET Framework SDK documentation and inspect the server trace logs.. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.79 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Monitoring b4ly Medium Leaving Monitored Scope (Application Authentication Pipeline). Execution Time=52.3525336320678 f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.79 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Application Authentication ajezs High SPApplicationAuthenticationModule: Error authenticating request, Error details { Header: {0}, Body: {1} }. Available
parameters: 3001000;reason="There has been an error authenticating the request.";category="invalid_client" {"error_description":"The server was unable to process the request due to an internal error. For more information
about the error, either turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug> configuration behavior) on the server in order to send the exception information back to the client, or turn on tracing as
per the Microsoft .NET Framework SDK documentation and inspect the server trace logs."} . f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.79 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 8nca Medium Application error when access /sites/testrpa2/_vti_bin/client.svc, Error=The server was unable to process the request due to an internal
error. For more information about the error, either turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug> configuration behavior) on the server in order to send the exception information back to
the client, or turn on tracing as per the Microsoft .NET Framework SDK documentation and inspect the server trace logs. at Microsoft.IdentityModel.Protocols.WSTrust.WSTrustChannel.ReadResponse(Message response) at Microsoft.IdentityModel.Protocols.WSTrust.WSTrustChannel.Issue(RequestSecurityToken
rst, RequestSecurityTokenResponse& rstr) at Microsoft.IdentityModel.Protocols.WSTrust.WSTrustChannel.Issue(RequestSecurityToken rst) at Microsoft.SharePoint.SPSecurityContext.SecurityTokenForContext(Uri context,
Boolean bearerToken, SecurityToken onBehalfOf, SecurityToken actAs, SecurityToken delegateTo, SPRequestSecurityTokenProperties properties) at Microsoft.SharePoint.SPSecurityContext.SecurityTokenForApplicationAuthentication(Uri context,
SecurityToken onBehalfOf) at Microsoft.SharePoint.IdentityModel.SPApplicationAuthenticationModule.<>c__DisplayClass4.<GetLocallyIssuedToken>b__3() at Microsoft.SharePoint.Utilities.SecurityContext.RunAsProcess(CodeToRunElevated
secureCode) at Microsoft.SharePoint.IdentityModel.SPApplicationAuthenticationModule.ConstructIClaimsPrincipalAndSetThreadIdentity(HttpApplication httpApplication, HttpContext httpContext, SPFederationAuthenticationModule fam)
at Microsoft.SharePoint.IdentityModel.SPApplicationAuthenticationModule.AuthenticateRequest(Object sender, EventArgs e) at System.Web.HttpApplication.SyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute()
at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.79 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8b Verbose Looking up context site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.79 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.80 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.80 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.80 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.80 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8b Verbose Looking up context site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in the farm SharePoint_Config_QA f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.80 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8d Verbose Looking up the additional information about the typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.80 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8f Verbose Site lookup is replacing
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly with the alternate access url
http://inetdev. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.80 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8g Verbose Looking up typical site
http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.80 w3wp.exe (0x1C74) 0x183C SharePoint Foundation General 6t8h Verbose Found typical site /sites/testrpa2 (407ba20c-079b-4b99-9e70-f86e6e13ddde) in web application SPWebApplication Name=SPDEV - 80. f5bd8793-a53c-2127-8485-418c67f110f6
04/16/2015 15:22:03.80 w3wp.exe (0x1C74) 0x183C SharePoint Foundation Monitoring b4ly Medium Leaving Monitored Scope (Request (GET:http://inetdev:80/sites/testrpa2/_vti_bin/client.svc/site/ReadOnly)). Execution Time=62.2890618779761 f5bd8793-a53c-2127-8485-418c67f110f6
Regards
Sakti -
I tried updating iTunes to version 11.1.1, but installation fails each time even when I did it manually as was suggested. The message I receive is: "The installer has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2324."
Hi hongkongpom,
Just wanted to say that after posting the problem, I had a chat with an iTunes' Tech Support, her name is Rebekah. My problem was resolved after that. Will list the chat history below in hopes that it may help you as well.
Good luck!
Samia
Chat Transcript
Friday, October 4, 2013 05:55 AM
Duration: 81 minutes 28 seconds
Rebekah:
Welcome to AppleCare chat support. Please give me a moment to look over your information.
Rebekah:
Hi, Samia! My name is Rebekah. If we get disconnected, please chat us back. http://www.apple.com/support/ipod/contactEnter the case number from the initial email we sent you. This gives the next advisor you chat with immediate access to your case history.
Rebekah:
Could you please confirm your serial number? I want to be sure we provide the best service possible for you, Samia!
SAMIA:
Sure, it's 8L8395UY2C5
SAMIA:
My problem is with iTunes.
Rebekah:
Thanks for that confirmation. Just a heads up, this is iOS Tech Support. We do support iPod touches, iPads, and iPhones, but not the iPod classic. But no worries! I can get you in touch with a phone Advisor who can get you in touch with the department that specializes in iPod classics and would be able to better assist you. Would that be OK?
SAMIA:
I wasn't able to install the new version of iTunes (version 11.1.1). The installation keeps failing. The they suggested the I install it manually and that failed too. I will attach the message I received.
SAMIA:
I don't have a problem with iPod.
SAMIA:
Just iTunes
Rebekah:
No problem! We can certainly troubleshoot iTunes as much as possible. It may come to the point that you may have to transferred, but we can do as much as possible during this chat!
Rebekah:
Thanks for the screenshot. It is a bit small so I am unable to fully see the message that you are receiving. What is the error message you are receiving?
SAMIA:
This is the message I received in case you weren't able to open the attachment: "The installer has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2324."
Rebekah:
Thanks for that info!
SAMIA:
Pleasure!
Rebekah:
What version of Windows (XP, Vista, 7) do you have?
SAMIA:
Windows 7
SAMIA:
Windows 7 Home Premium
Rebekah:
Thanks for that confirmation. I do apologize for the delay, Samia. I am researching this error code now. You mentioned trying to install iTunes manually. To be sure I am on the same page, what steps did you take to do that?
SAMIA:
Well when the indsatalltion failed I was given instructions to select Download Only from Tools and then install manually. When I did it, I window popped up with the following items: - AppleApplicationSupport
SAMIA:
- AppleMobileDeviceSupport64
SAMIA:
- Bonjour64
SAMIA:
iTunes64
SAMIA:
SetupAdmin
SAMIA:
I selected Repair in all of them instead of Remove and all worked but iTunes64
SAMIA:
That's when I received the message that I sent you earlier.
SAMIA:
By the way, this is the fir st time something like this occured. I never had problems with installation before.
Rebekah:
I completely understand what you're saying. Since that Repair did not resolve the issue, our best option is to uninstall iTunes and its components and redownload it. To do this, we will follow the steps in this article: Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
Rebekah:
First, we will want to quit iTunes and/or Apple Software Update if those are open at this time.
SAMIA:
Rebekah, the instructions you gave says, "For Windows XP, follow these steps to remove and reinstall iTunes and other software components for Windows XP."
SAMIA:
I closed all applications
SAMIA:
Also, my iTunes doesn't open anymore after the new failed installation.
Rebekah:
The section that says "For Windows XP…" is in case we opened up the wrong article, as we have the one for Windows Vista, 7, or 8. There is a link to click ("these steps") in those directions that would take us to the article for uninstalling on a Windows XP.
Rebekah:
So no worries! We have the right article!
Rebekah:
On the computer, we will want to click on Start > Control Panel. In Control Panel, we will click the "Uninstall a program" link.
SAMIA:
I thought so after doing a little exploration.
SAMIA:
done
Rebekah:
Alright, we'll want to select iTunes from the list of currently installed programs. Then we will click Uninstall. When asked if you would like to remove iTunes, let's click Yes.
Rebekah:
After the uninstallation is complete, we don't want to restart your computer if you're prompted.
SAMIA:
Done
Rebekah:
Then if you see other iTunes entries on the list, we'll want to remove them the same way.
Rebekah:
Then we will remove all instances of Apple Software Update the same way you removed iTunes.
SAMIA:
Okay, but do I have to remoce iCloud as well?
SAMIA:
Rebekah, I received the same error message again when uninstalling
Rebekah:
We actually do not need to remove iCloud. After the Apple Software Update, we will want to remove all instances of Apple Mobile Device Support
Rebekah:
How strange! Are you able to click past that and allow the process to continue or has it stopped it completely?
SAMIA:
I am unable to uninstall iTunes either
SAMIA:
Stopped completely
SAMIA:
I treied clicking Repair
Rebekah:
Alright, after trying the Repair option, let's see if it will allow us to continue uninstalling or not.
SAMIA:
I tried that but unfortunately, it isn't working. I still get that same message with error code 2324.
Rebekah:
This error code is not something that I am finding in my sources, Samia. So there is a chance that it is being caused with the Windows computer itself. However, I did find a link that may be able to help with uninstalling iTunes from Windows' support site: http://support.microsoft.com/mats/Program_Install_and_Uninstall
SAMIA:
Rebekah, you're a genius! It worked! iTunes is no longer there. What next?
Rebekah:
Awesome! I'm glad that worked!
Rebekah:
To be sure I am on the same page, what was the last component we uninstalled?
SAMIA:
iTunes
SAMIA:
Shall I remove the Apple Application Support, Apple Mobile Device Support, and Apple Software Update
Rebekah:
That is correct! However, we do want to uninstall it in the order I mentioned above. So Apple Software Update first, Apple Mobile Device Support next, and then Apple Mobile Device Support.
SAMIA:
Got it, but is the second one to uninstall Apple Mobile Device Support OR Apple pplication Support?
Rebekah:
The second one is Apple Mobile Device Support.
Rebekah:
The Application Support will be the last component we uninstall.
SAMIA:
Thanks! I'm on it.
SAMIA:
Done! ll 3 are gone, well 4 with iTunes. Now what?
Rebekah:
Awesome! Also, I just noticed that I accidentally typed Apple Mobile Device Support twice, I do apologize for any confusion! Now we will remove all instances of Bonjour and then remove all instances of Apple Application Support.
SAMIA:
There was only 1 instance with Bonjour. I don't know what the instances are for Apple Application Support
Rebekah:
Yes, Bonjour is often only listed once. Is the Apple Application Support listed at all?
SAMIA:
No
SAMIA:
Since I removed it
Rebekah:
Oh, perfect! If it was removed, we should be set!
Rebekah:
We have removed iTunes and its components now! From here, our next step is to restart the computer. Then once you reboot, you can redownload iTunes from apple.com/itunes
Rebekah:
That should allow you to download iTunes!
SAMIA:
Shall I downloaad the latest vesion?
Rebekah:
You will want to first restart the computer as shown in the article. That will ensure that this process goes smoothly and that everything was removed correctly! Then you can try downloading iTunes again.
SAMIA:
Okay, thanks Rebekah!
Rebekah:
You're very welcome! I'm glad I could help! And of course if you have any issue after the reboot and download, you can always chat us back, as chat is open 24 hours! You will just need to give your case number and the next Advisor would have all my notes!
SAMIA:
Thanks again for all your help, for I couldn't have managed with out it. Have a nice day!
Rebekah:
You're very welcome! I know how important iTunes is and I'm glad we could get you on a path to resolution!
Rebekah:
I hope you have a lovely day!
Rebekah:
It's been a pleasure speaking with you! Thanks for chatting with us Samia. If you don't have any more questions, select End Chat from the upper left corner of the chat window.
SAMIA:
Will do, thanks. -
Problem with Alt Text output from thumbnail image of Lightbox widget
I’m having a problem with the Lightbox widget not producing alternative text based on the image properties. I’ve set ALT text for the image properties on both the larger Ligtbox image as well as the thumbnail. But the HTML output from Muse does not include the ALT text on the thumbnail version of the image. Here’s an example:
<div class="popup_anchor">
<div class="Thumb popup_element clearfix" id="u4409"><!-- group -->
<a class="anchor_item grpelem" id="untitled"></a>
<div class="grpelem" id="u4433"><!-- image -->
<img id="u4433_img" src="/images/n0060292x292.jpg" alt="" width="292" height="292" />
This may be a problem that came in a previous release of Muse. I have a few older examples where ALT text is produced, but it’s no longer updated if I update the Image Properties.I'm seeing the same problem. Looks like a bug to me. Any ideas as to how we can get this on Adobe's bug fix list?
-
I use the CS6 suite with Acrobat XI at windows platform.
When I want to save a file from InDesign as .pdf with output intention eci_iso_coated_v2_300 the result is a .pdf with more than 300% ink coverage.
I tried to transform the result in Acrobat XI into this standard output intention, but also the result has more than 300 % ink coverage.
What is the reason of this bug?
Before with Acrobat X this worked without problemsHi Rob,
I was told the new way to work would be to draw files via Bridge direct into the InDesign file
and I thought automatically the color would not be changed.
my colourmanagement setting in bridge for the whole CS6 was ECI isocoated_V2_300
The Illustrator file was saved without color profile.
In this test file I used 3 kinds of black: background of pirate in cmyk 79,34 / 72,78 / 59,38 / 79,88 = ink coverage 291 %
DÜSSELPIRATEN in “black” (if you would convert this in the file with the cmyk button it would be the same ink-percentage as before
“e.V.” was set to 100 % k
I set the preferences for Acrobat from InDesign CS6 as pdf X4 with profile eci isocoatedV2_300 in three ways:
no color conversion
convert to profile
convert to profile keeping existing values
in all tree files the pirates background has 322 % ink coverage instead of 291 %
Why does Acrobat convert “black” in the wrong way? If I click in Illustrator on the 4c button to convert the “black” into 4c it is 291% ink
Acrobat should come to the same result with all profiles: iso coated V2 and iso coated V2_300
The same happens also by saving as .pdf X3 or .X1
The minimum what I expect is, that Acrobat reduces ink coverage for black to 300 %
I also made test with the new ECI profiles for laminated prints from 2012.
And with newspaper profiles
In this case the ink coverage comes below 300 %, but only when I choose convert to profile.
And then the 100 % k converts to cmyk, what I don’t want to have with text.
Is there no way to reduce ink coverage below a special percentage without changing Text 100% k
And is there a bug in Acrobat XI with the ECI IsoCoated_V2_300 Profile? For there is no color reduction below 300 % in all conversion settings.
I can’t test this with Acrobat X or IX, for my computers with this software don’t run with CS6 64 bit.
enclosed you find my files
Kind regards
Lutz Hanbueckers
Hanbueckers Werbung GmbH
Brandsackerstr. 5
40764 Langenfeld
P.O. Box 40 02 01
40242 Düsseldorf
Tel. +49 02173 1 09 44 - 0
Fax +49 02173 1 09 44 - 10
[email protected] <mailto:[email protected]>
www.hanbueckers.de
Visit our site
Steady attractive offers!!!
HR Düsseldorf B 26 480
owner Manager: Lutz Hanbueckers
Von: Rob Day [email protected]
Gesendet: Samstag, 2. März 2013 04:26
An: Hanbueckers Werbung
Betreff: acrobat/Indesign does not export correct into the selected output intention (eci_iso_coated_v2_300)
Re: acrobat/Indesign does not export correct into the selected output intention (eci_iso_coated_v2_300)
created by Rob Day <http://forums.adobe.com/people/rob+day> in InDesign - View the full discussion <http://forums.adobe.com/message/5115613#5115613
Maybe you are looking for
-
HT204053 How can I sync two different email accounts?
How can I sync two different email accounts? All of this Mobile Me and cloud stuff got me all flustered and now I have two accounts possibly 3.
-
Problem Deploying Custom Transformation Provider to Remote System
Hello Experts, I have successfully created a custom XML Transformation Provider/transformer and deployed it to my local development system and to a remote sandbox system. We are using NWDI and the transformation provider is within the context of a DC
-
Problem in Calling URL for Line Item of Perticular Purchase Requisition.
Hi Experts, I am calling a external window from the web dynpro which is working fine. I am trying to open transaction ME53 in the browser and i am successful in that. But now when i open that transaction there were two requirements: *1) It should
-
How to highlight only one column
I am trying to highlight and copy one column but the one next to it is also highlighted. Help!!
-
Where can I get a replacement case fan for a HP Pavillion 180t
The case fan on my 5 year old HP Pavillion 180t has begun to make noise when running. This is the fan mounted to the back of the case, drawing air over the CPU cooling stack. From what I can gather from the HP support site, this model is no longer s