Does the Cisco 26XX-XM router support E1 CAS signaling

Does the Cisco 2600-XM series router support E1 CAS signalling for its E1 digital voice port or jst only support E1 R2 signaling.
Thanks

Only E1 R2 and E1 PRI.
Taimoor

Similar Messages

  • Does the Westell 9100VM FiOS Router support 802.11 "n" ????

    I have a westell 9100VM router and I want to installed a 802.11n adapter in my PC.  But I'm not sure is the router will support it.  Any suggestions???

    I found the official manual for this device..
    http://www22.verizon.com/ResidentialHelp/FiOSInternet/Networking/Setup/Vz9100/122193.htm
    .. to answer your question:
    It has a wireless G Access Point.
    With a wireless G access point, you get up to wireless G speeds if the wireless works.
    Wireless G speed = 54 MB.
    If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

  • Making a VoIP call with the Cisco 837 ADSL router

    I would greatly appreciate if could please provide some technical assistance to my questions below:
    Is it possible to make a VoIP call between two 837 ADSL Cisco routers over a 1Mbps ADSL broadband connection?
    If so, can I configure this VoIP connection using either a PPPoE or ATM WAN link?
    Is it possible to make a VoIP call using a Cisco 837 Router while simultaneously surfing the Internet? In other words do I need two public IP addresses i.e. one for accessing the internet and one for making the VoIP call or is one static IP address obtained from my ISP sufficent.
    It is possible to configure QoS parameters (e.g. RSVP, Voice precedence, Voice codec selection) on this 837 router using PPoE or can it only be done using an ATM WAN interface?
    Does the Cisco 837 router support both the H.323 and SIP communication protocols? Do I need to purchase a certain IOS operating system version for VoIP calling?
    Does the VoIP dial peers need to be configured with both a POTS and VoIP phone numbers or is only one number required?
    Do I need to obtain a special VoIP number from my VoIP service provider? or can I use existing POTS numbers or made up numbers within the dial peers as this situation involves making a private VoIP call between two branch offices using 837 ADSL routers and not via a VoIP service provider.
    Finally, can I use POTS ordinary telephones with the Cisco 837 for making VoIP calls or do I strictly need to purchase VoIP phones?
    My apologies for the number of questions asked here but I currently need to know the technical ability of the Cisco ADSL 837 as I am thinking of employing these routers in my company organisation.
    I await your feedback in due course.
    Thanks,
    Martin Healy

    Hi,
    I give you a sample config of my router.
    class-map voice
    match access-group 101
    policy-map mypolicy
    class voice
    priority 128
    class class-default
    fair-queue 16
    ip subnet-zero
    gateway
    interface Ethernet0
    ip address 20.20.20.20 255.255.255.0
    no ip directed-broadcast (default)
    ip route-cache policy
    ip policy route-map data
    interface ATM0
    ip address 10.10.10.20 255.255.255.0
    no ip directed-broadcast (default)
    no atm ilmi-keepalive (default)
    pvc 1/40
    service-policy output mypolicy
    protocol ip 10.10.10.36 broadcast
    vbr-nrt 640 600 4
    ! 640 is the maximum upstream rate of ADSL
    encapsulation aal5snap
    bundle-enable
    h323-gateway voip interface
    h323-gateway voip id gk-twister ipaddr 172.17.1.1 1719
    h323-gateway voip h323-id gw-820
    h323-gateway voip tech-prefix 1#
    router eigrp 100
    network 10.0.0.0
    network 20.0.0.0
    ip classless (default)
    no ip http server
    access-list 101 permit ip any any precedence critical
    route-map data permit 10
    set ip precedence routine
    line con 0
    exec-timeout 0 0
    transport input none
    stopbits 1
    line vty 0 4
    login
    voice-port 1
    local-alerting
    timeouts call-disconnect 0
    voice-port 2
    local-alerting
    timeouts call-disconnect 0
    voice-port 3
    local-alerting
    timeouts call-disconnect 0
    voice-port 4
    local-alerting
    timeouts call-disconnect 0
    dial-peer voice 10 voip
    destination-pattern ........
    ip precedence 5
    session target ras
    dial-peer voice 1 pots
    destination-pattern 5258111
    port 1
    dial-peer voice 2 pots
    destination-pattern 5258222
    port 2
    dial-peer voice 3 pots
    destination-pattern 5258333
    port 3
    dial-peer voice 4 pots
    destination-pattern 5258444
    port 4
    end

  • License on the Cisco 3900 Series router.

    I am trying to understand what does the "data" license exactly do on the Cisco 3900 series router. What I understood is that the data license supports "MPLS.ATM. Multiprotocol support".
    Question is is a do not have this license will I not be able to run BGP, EIGRP and terminate service provider links?
    Technology Package License Information for Module:'c3900e'
    Technology    Technology-package                  Technology-package
                  Current              Type           Next reboot
    ipbase        ipbasek9             Permanent      ipbasek9
    security      securityk9           Permanent      securityk9
    uc            None                 None           None
    data          None                 None           None
    NtwkEss       None                 None           None
    CollabPro     None                 None           None
    Configuration register is 0x2102
    Thanks,
    Nik

    I think WAAS express is one of the technologies you will lose out on. Amongst other advanced features. See link below.
    http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/software-activation-on-integrated-services-routers-isr/white_paper_c11_556985.html
    EDIT: And performance routing.

  • Does the UCS C-Series Servers supports PCI/e card digium T1/E1

    Hello,
    Does the UCS C-Series Servers supports/compatible with PCI/e card digium  TE407P/TE420 T1/E1.?
    The server will be used as Asterisk server.
    Thanks
    Philip

    Hi Philip,
    Compatibility will depend on the server model that you have and whether the digium card is a full length, low profile, or half length pcie card.  Take a look at http://www.cisco.com/en/US/products/ps10493/prod_models_comparison.html#~tab-a for details.  If there are any issues with the card itself once it is installed it will have to go through the 3rd party manufacturer.

  • Does the iPod Classic 7th generation support movies in the HD format?

    Does the iPod Classic 7th generation support movies in the HD format as well as SD or just SD?

    No, the max resolution for video playback is generally 640x480, as stated in the specs
    http://www.apple.com/ipodclassic/specs.html
    The screen is actually half of that resolution, at 320x240.  HD at 720p is 1280x720.  HD at 1080p is 1920x1080

  • Does the web server of weblogic support any plugins

    Does the web server of weblogic support any plugins similar to the ISAPI plugins for IIS or apache plugins?

    i can't seem to get it to work either AND I can't seem to find an answer here or any search that I do.  It seems that you can only view your calendar and not delegate calendars via the web view

  • Does the HP OfficeJet Pro 8600 support e-print? I am running on Win 7 Pro 64 bit

    Can you please tell me: does the HP OfficeJet Pro 8600 support e-print?  I cannot seem to find or generate or figure out how to create an e-mail address for this printer.  Thank you.
    This question was solved.
    View Solution.

    Hello BoPeepLamb,
    The OfficeJet 8600 Printer does support ePrint. You can access the printers email address by enabling Web Services from the main display on the printer. The icon is located on the top left corner of the screen and looks like piece of paper with circles behind it. Before you can enable Web Services you must make sure you have a valid internet connection first.
    Once you have enabled Web Services, you should have a mobile printing sheet print with a printer code and link to http://www.eprintcenter.com where you can create an account and customize your printers email address.
    If you have any other questions feel free to reply to this post and I will try to find an answer for you.
    If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
    Although I work for HP, my posts and replies are my own opinion and not those of HP.

  • Does the GeoRaster method SDO_GEOR.exportTo support the Erdas IMG format?

    Hi Everyone,
    Does the GeoRaster method SDO_GEOR.exportTo support the Erdas IMG format, and SDO_GEOR.exportTo method can export what maximum amount of data?
    Best Regards,
    Lin

    Lin, thanks for your suggestion. the gdal-georaster integration is a great one for GIS and professional usages and can do what exportTo can not do even though it was just recently available. note though, all existing georaster functions, including exportTo, are internally built inside the database server from ground up. this enables users to fully leverage the power of enterprise database and grid computing.
    thanks
    jeffrey

  • Does the Cisco 1552E have a heater in it?

    Does the Cisco 1552E have a heater in it?
    I see a heater status in the WLC! lol I am just wondering.

    I have often wondered how this works myself. Does the heater turn on automatically once the unit falls below a certain temperature? Is their a way to turn it on manually? 
    I would like to see some documentation on this. I have searched and unfortunately have found no documentation on this.

  • I have a newer MacBook Pro and I am trying to download my Final Cut Pro 7 Studio 2 on it. Is that possible or does the new MacBook Pro not support anything other than Final Cut Pro X?

    I have a newer MacBook Pro and I am trying to download my Final Cut Pro 7 Studio 2 on it. Is that possible or does the new MacBook Pro not support anything other than Final Cut Pro X?

    As Tom said the FCS forum is the better place to post the question.
    Here is Apple's best practices doc for installing both on the same system.
    BTW, FCP7 is part of the FCS 3 suite of apps.
    Russ

  • Does the JRE 1.5 is supported for the WLS 8.1SP3 client

    Hi,
    Does the JRE 1.5 is supported for the WLS 8.1SP3 client
    Regards,
    Ahamad

    Hi,
    Does the JRE 1.5 is supported for the WLS 8.1SP3 client
    Regards,
    Ahamad

  • Does the HP ENVY dv7-7240us support two internal hard drives?

    Does the HP ENVY dv7-7240us support two internal hard drives?
    Is this something we can expand ourself without requiring a special chasis?

    Hi,
    Yes, it supports TWO internal HDD's. You may need something similar to this:
        http://www.newmodeus.com/shop/index.php?main_page=page&id=39
    the following video will give you some ideas:
       http://www.youtube.com/watch?v=cLP8kjeLW-Q
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Does the IE CS6 version have Support for the Middle Eastern tool set? - left to right typing etc.

    Does the IE CS6 version have Support for the Middle Eastern tool set? - left to right typing etc.

    I assume IE means International English, as opposed to English North America (aka US English). There is Middle Eastern and Hebrew support via an English user interface for programs that support it such as InDesign.
    You can change the install language by launching the Adobe Application Manager and clicking on your name in the top left to bring up a context menu. From the menu select Preferences and then click the drop down for Languages. See the screen shot below:

  • Does the MSI P965 Neo-F support ECC memory?

    Can it handle 2x 1 GB DDR2 ELPIDA PC2-5300, 667 MHz, ECC
    Does the MSI P965 Neo-F support ECC memory?

    As mentioned by many, No ECC RAMs support.
    To me, I feel that current state of art DDR II RAMs are good enough to not produced much errors and HDDs have error buffer memory of up to 16MB, so ECC makes me feels that it is a "good to have but not a must" thing nowdays.

Maybe you are looking for

  • I changed the format to an external drive and lost everything that was on it.

    I changed the format on an external hard drive and lost everything that was on it. Is there a way to recover what was on it?

  • Not able to update the partner with a new partner during change order ?

    Hi Experts, I want to update a partner which is present in a sales order with a new partner. When i create a new order, i ll give partner function ship-to-party and partner no 1 for this partner function. And from a fucntion module, i want to change

  • HTML Viewer: Copying images+text to another component

    Hi folks, I'm working on a Java app for a research project where I'd like to be able to view a webpage in one panel (with some HTML viewer) and then be able to select pictures AND text from it (web browser-style), click a button, and have it copy the

  • HT1386 This is a problem.

    This is a problem. So I reset media and data by accident. So i start it up again, and it says to sync my usb to itunes, and guess what? it won't sync. Wow now I can't even start my ipad. Any help?

  • Screen is stretched

    I just bought an new Apple TV and connected using component video to my plasma screen. Everything works fine, but the content of what is displayed is stretched or zoomed (ie I can't see the entire image because the edge of the images are beyond the e