Does the CRS-1 MSC fail?

HI,ALL
when I telnet the CRS-1,I use show diag sum ,show led,show inv command,does the 0/13/* MSC fail?
I have not seen the machine,is there SIP-800 no SPA card cause the problem?
==========================================================================================
show diag sum
CARD 0/13/* : Unknown Card Type
PLIM 0/PL13/* : Cisco Carrier Routing System SPA Interface Processor Card (NO MSC)
CARD 0/RP0/* : Cisco CRS Series 16 Slots 6 GB Performance Route Processor
CARD 0/RP1/* : Cisco CRS Series 16 Slots 6 GB Performance Route Processor
=============================================================================================
show led
RP/0/RP0/CPU0:FZ-QY-CR-1.MAN.CRS#
0/13/*: Module (host) LED status says: OK
0/13/*: Module (jacket) LED status says: Unknown
======================================================================
RP/0/RP0/CPU0:FZ-QY-CR-1.MAN.CRS#show inventory location 0/13/CPU0
Wed Jan 14 15:52:43.142 GMT
NAME: "0/13/*", DESCR: "Cisco CRS-1 Series Modular Services Card revision B"
PID: CRS-MSC-B         , VID: V08, SN: SAL1614915K
NAME: "0/PL13/*", DESCR: "Cisco Carrier Routing System SPA Interface Processor Card"
PID: CRS1-SIP-800      , VID: V04, SN: SAD140200WY
=======================================================================
RP/0/RP0/CPU0:FZ-QY-CR-1.MAN.CRS#admin show led
Wed Jan 14 23:33:08.402 GMT
     LOCATION        MESSAGE        MODE      STATUS
    ==================================================
         0/0/*       IOS XR        DEFAULT   UNLOCKED
         0/1/*       IOS XR        DEFAULT   UNLOCKED
         0/2/*       IOS XR        DEFAULT   UNLOCKED
         0/3/*       IOS XR        DEFAULT   UNLOCKED
         0/4/*       IOS XR        DEFAULT   UNLOCKED
         0/5/*       IOS XR        DEFAULT   UNLOCKED
         0/6/*       IOS XR        DEFAULT   UNLOCKED
         0/7/*       IOS XR        DEFAULT   UNLOCKED
         0/8/*       IOS XR        DEFAULT   UNLOCKED
         0/9/*       IOS XR        DEFAULT   UNLOCKED
        0/10/*       IOS XR        DEFAULT   UNLOCKED
        0/11/*       IOS XR        DEFAULT   UNLOCKED
        0/12/*       IOS XR        DEFAULT   UNLOCKED
        0/13/*       IOS XR        DEFAULT   UNLOCKED
       0/RP0/*       ACTV RP       DEFAULT   UNLOCKED
       0/RP1/*       STBYRDY       DEFAULT   UNLOCKED
       0/FC0/*       IOS XR        DEFAULT   UNLOCKED
       0/FC1/*       IOS XR        DEFAULT   UNLOCKED
       0/AM0/*        0  13  SP    DEFAULT   UNLOCKED
       0/AM1/*        0  13  SP    DEFAULT   UNLOCKED
       0/SM0/*       IOS XR        DEFAULT   UNLOCKED
       0/SM1/*       IOS XR        DEFAULT   UNLOCKED
       0/SM2/*       IOS XR        DEFAULT   UNLOCKED
       0/SM3/*       IOS XR        DEFAULT   UNLOCKED
       0/SM4/*       IOS XR        DEFAULT   UNLOCKED
       0/SM5/*       IOS XR        DEFAULT   UNLOCKED
       0/SM6/*       IOS XR        DEFAULT   UNLOCKED
       0/SM7/*       IOS XR        DEFAULT   UNLOCKED

RP/0/RP0/CPU0:FZ-QY-CR-1.MAN.CRS#show platform
Fri Jan 16 10:21:42.874 GMT
Node          Type              PLIM             State           Config State
0/0/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/0/0         MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/0/1         MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/0/2         MSC-B(SPA)        5X1GE            OK              PWR,NSHUT,MON
0/0/4         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/0/5         MSC-B(SPA)        2XOC48-POS       OK              PWR,NSHUT,MON
0/1/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/1/0         MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/1/1         MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/1/2         MSC-B(SPA)        5X1GE            OK              PWR,NSHUT,MON
0/1/4         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/1/5         MSC-B(SPA)        2XOC48-POS       OK              PWR,NSHUT,MON
0/2/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/2/0         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/2/1         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/2/4         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/2/5         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/3/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/3/0         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/3/1         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/3/4         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/3/5         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/4/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/4/0         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/4/1         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/4/4         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/5/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/5/0         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/5/1         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/5/2         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/5/3         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/5/4         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/5/5         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/6/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/6/0         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/6/1         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/6/2         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/6/3         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/6/4         MSC-B(SPA)        8X1GE            OK              PWR,NSHUT,MON
0/6/5         MSC-B(SPA)        5X1GE            OK              PWR,NSHUT,MON
0/7/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/7/0         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/7/1         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/7/4         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/7/5         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/8/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/8/0         MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/8/1         MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/8/4         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/8/5         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/9/CPU0      MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/9/0         MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/9/1         MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/9/4         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/9/5         MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/10/CPU0     MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/10/0        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/10/1        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/10/4        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/10/5        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/11/CPU0     MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/11/0        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/11/1        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/11/4        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/11/5        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/12/CPU0     MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/12/0        MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/12/1        MSC-B(SPA)        OC192RPR-XFP     OK              PWR,NSHUT,MON
0/12/4        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/12/5        MSC-B(SPA)        1x10GE           OK              PWR,NSHUT,MON
0/13/CPU0     MSC-B             Jacket Card      IOS XR RUN      PWR,NSHUT,MON
0/RP0/CPU0    RP(Active)        N/A              IOS XR RUN      PWR,NSHUT,MON
0/RP1/CPU0    RP(Standby)       N/A              IOS XR RUN      PWR,NSHUT,MON

Similar Messages

  • Why does the Adobe Updater keep failing?

    Why does the Adobe Updater keep failing? I close my Webroot antivirus app and the update keeps failing for the Extension Manager 6.0.8 Update. The message is "Extension Manager 6.0.8 Update Installation failed. Error Code: U44M1P7". I cannot retry until the Adobe Updater appears again in the notification bar (lower right of my Win 7 desktop.

    Hi,
    You can try to manually install the updates:
    Product updates
    Helpful Links:
    Installation failed. Error U44M1P7 | Updates
    http://helpx.adobe.com/photoshop/kb/photoshop-cs6-updates-dont-install.html

  • Why does the update of PShopCC fail?

    In Creative Cloud, I cannot update PhotoShop. It downloads and then says "Update Failed. Errors encountered during installation (U44M1P7)."

    Please follow the instructions given in kb document : http://helpx.adobe.com/creative-suite/kb/error-u44m1p7-installing-upda tes-ccm.html

  • WHY DOES THE PE EDITOR KEEP FAILING TO LOAD

    I have a brand new problem with Photoshop Elements 8, which I've been using in Windows for several years.
    Suddenly the PE editor refuses to load--either from "Fix" in the album space or from "Edit" in the Workspace. It starts to load (with the green dots moving across the bar) and then kicks out.  Even after I signed in successfully to PE,  the editor still fails to load. Any suggestions?

    One easy fix for Adobe programs is to Reset Preferences = Press/HOLD Ctrl+Alt+Shift while starting program
    IF your problem is a corrupted preferences file, this is the fix

  • Why does the 3g data network fail every day?

    Goes down for at least an hour a day

    Is this in a highly populated area? Is it the same location and time usually?

  • Does the Roboform plugin still fail to work with the new upgrade?

    Roboform disappeared with new upgrade. I went back to old version. WORKS fine...

    Yes, thank you for your help and assistance. I tried the upgrades and now Roboform wants me to purchase the latest version. So, I uninstalled and went back to the original setup. Same problems occurred when I purchased a new laptop using Win Vista Ultimate. Some of my external hardware stopped working. Can't get drivers. Buy new hardware to support the unnecessary Win operating system changes? When will it end? WIN 8? I think not.

  • HT201109 Final Cut Pro X - Why does the trial version keep failing?

    Process:         Final Cut Pro Trial [4005]
    Path:            /Volumes/VOLUME/Final Cut Pro Trial.app/Contents/MacOS/Final Cut Pro Trial
    Identifier:      com.apple.FinalCutTrial
    Version:         10.0.8 (221398)
    Build Info:      ProEditor-22139008018000000~2
    Code Type:       X86-64 (Native)
    Parent Process:  launchd [144]
    Responsible:     Final Cut Pro Trial [4005]
    User ID:         501
    Date/Time:       2013-12-21 00:01:58.489 -0500
    OS Version:      Mac OS X 10.9.1 (13B42)
    Report Version:  11
    Anonymous UUID:  010133C7-71FE-7E00-B668-9077858DDF11
    Sleep/Wake UUID: 5697EF8F-BAA6-42A2-91C1-DF989828B00C
    Crashed Thread:  2  BGTask: FFThumbnailRequestManager  Dispatch queue: NSOperationQueue Serial Queue
    Exception Type:  EXC_BAD_ACCESS (SIGSEGV)
    Exception Codes: KERN_INVALID_ADDRESS at 0x0000000000000000
    ETc......

    the trial has no length limit.
    my assumption:
    you try to handle wmv material, using the flip4mac plugin
    its free trial has a length limit.
    purchase a licence …

  • TS1368 Why does the app store sometimes fail to connect?

    I often cannot connect to the app store with my new iPad, while I can at other times.  All the support suggestions suggest that my WiFi connection is the problem. However all the other apps that need the WiFi connection, such as Safari, email and Dropbox work all the time. This seems to indicate that my connection is OK. Why is the app store app unable to connect reliably?

    It will happen if you activate a new device in your iTunes account, such as a new iPod, or, from my experience, randomly. Apple stepped up security some months back to cut down on fraudulent purchases.

  • Does the battery fail in cold temperatures i.e. -24

    does the i-phone battery fail in cold temperatures like -14

    Yes, the battery could fail if you are using the phone outside the environmental requirements:
    Environmental Requirements
    Operating ambient temperature: 32° to 95° F (0° to 35° C)
    Nonoperating temperature: -4° to 113° F (-20° to 45° C)
    http://www.apple.com/iphone-6/specs/

  • CRS 5 Backups fail with this error: Unknown error occured while connecting to the host

    Dear All,
    We have backup issue with  UCCX 5.0(2)SR03_Build317, while trying to take  backup giving following error "Unknown error occurred while connecting to the host".
    I have found the solution in the Cisco and tried all the suggestion, still not working and same error observed. Due to backup issue we unable to do any changes on the CRS, when we try to create new agents, those agents are not reflecting in the CRS.
    Also I have observed bellow error , when try to re-sync the JTAPI,
    Error while handling the input   request.
    Top of Form
    Config Changes are not allowed during 'Backup' operation, which   was started by 'Scheduler' at 'Fri Jun 08 18:00:03 GMT+08:00 2012 '. Please   try again after 'Backup' is complete.
    Bottom of Form
    http://www.cisco.com/en/US/products/sw/custcosw/ps1846/products_tech_note09186a00809a752c.shtml
    Solution
    Complete these steps in order to resolve this issue:
    •1.      Access the UCCX server and navigate to Start > Run, and type CET.
    •2.      When the warning message appears, click NO.
    •3.      Choose com.cisco.crs.cluster.config.ArchiveAdminConfig.
    •4.      On the right side, double-click the record ID.
    •5.      Click the com.cisco.crs.cluster.config.ArchiveAdminConfig tab, and clear the password under Backup Storage.
    •6.      Click Apply.
    •7.      Navigate to Appadmin > Tools > Backup and Restore.
    •8.      Under Backup Storage Location, type the new password, and click Update.
    After you complete these steps, you can run the backup. If the backup fails, restart the server, and try the backup again. If the backup still fails, you can navigate to CET, clear all the fields, and then type the new information for the storage location.
    Please help me with your suggestions.
    Thanks & Regards,
    Naveen .S

    Please any one help me on this issue..

  • Does the iPhone 4 disable for 24 hours after too many failed attempts at entering the passcode

    Does the iPhone 4 disable for 24 hours after too many failed attempts at entering the passcode

    Oh thank you. Only thing is I have no backup, so i'd prefer to wait if there is a 24 hour lock out... Someone told me they thought there was, and I can't find anything on google to tell me how many attempts you get and how long you get locked out for each time. A friend made me a new passcode when under the influence and now after thinking about it remembers what he changed it to

  • Does a table/view still return records if the underlying VPD policy fails ?

    Hi All,
    I have one following question -
    Does a table or view still return records if the underlying VPD policy fails?
    I am adding one more thing here. Let us say security is being implemented using the application context and VPD.
    What would happen when application context is not set ? Would the application apply any default privilege as VPD?
    Thanks,
    Ashi

    AshiKD wrote:
    Hi All,
    I have one following question -
    Does a table or view still return records if the underlying VPD policy fails?No, you get a standard error message if the VPD function is wrong and if you won't pass the conditions of the VPD, you get nothing. That's what in general happens and should happen as well.
    >
    I am adding one more thing here. Let us say security is being implemented using the application context and VPD.
    What would happen when application context is not set ? Would the application apply any default privilege as VPD?This would be a wrong approach then. If you are truly setting a VPD, you have to make sure that the context is set and the condition variable are passed through it. This is normally done through a logon trigger so again, generically , its not possible that it would not be set. I didn't get at all what ever you said in the last line? What is "default priv for VPD" ?
    HTH
    Aman....

  • R3load -testconnect fails while doing the Export Prepare

    Hi All,
    R3load -testconnect fails while doing the Export Prepare for the Unicode Conversion. I have upgraded the CRM system from CRM 4.0 to SAP Netweaver 7.0 with EHP1. Now I doing the Unicode Conversion. While using the sapinst as root to start the unicode conversion I am getting the following error:
    /usr/sap/CSX/SYS/exe/run/R3load -testconnect [E]
    sapparam: sapargv( argc, argv) has not been called.
    sapparam(1c): No Profile used.
    sapparam: SAPSYSTEMNAME neither in Profile nor in Commandline
    /usr/sap/CSX/SYS/exe/run/R3load: START OF LOG: 20090603143131
    /usr/sap/CSX/SYS/exe/run/R3load: sccsid @(#) $Id: //bas/701_REL/src/R3ld/R3load/R3ldmain.c#5 $ SAP
    /usr/sap/CSX/SYS/exe/run/R3load: version R7.01/V1.4
    Compiled Mar 10 2009 23:03:11
    /usr/sap/CSX/SYS/exe/run/R3load -testconnect [E]
    (DB) ERROR: DbSlControl(DBSL_CMD_IMP_FUNS_SET) rc = 20
    (DB) ERROR: DbSlErrorMsg rc = 20
    /usr/sap/CSX/SYS/exe/run/R3load: job finished with 1 error(s)
    /usr/sap/CSX/SYS/exe/run/R3load: END OF LOG: 20090603143131
    Regards
    Karthik Ravoori

    Hi,
    These note May help you.
    where are you placing the New executables.Always use /sapmnt/SID/exe.If you are placing them in /usr/sap/CSX/SYS/exe/run/ then you always get the error.
    I found in one of the note the same error that you are getting.
    Search in note with text DbSlControl(DBSL_CMD_IMP_FUNS_SET) rc = 20
    Note 459899 - SAP BW 3.0A Server Installation: UNIX/Oracle
    This Note Talks about the verson you should have for the kernel
    Note 898181 - Corrupt cluster record creates signal 11
    Thanks
    Rishi Abrol

  • I downloaded the latest itunes and i recieved a message that the apple mobile device failed to start.  It asks me to verify that I have sufficient privileges to start system services.  What does this mean and how do I fix this so computer will sync iphone

    i downloaded the latest itunes and i recieved a message that the apple mobile device failed to start.  It asks me to verify that I have sufficient privileges to start system services.  What does this mean and how do I fix this so computer will sync iphone?

    You need to follow the instructions of tt2 in https://discussions.apple.com/thread/5822086 to straighten it out.

  • CRS-MSC Can't be Recognized by the CRS-1 System.

    Hi.
       Beside me is a Cisco CRS-1 Series 16 Slots Carrier Routing System/Single, and it's running fine, the software running on the system is Cisco IOS XR Software, Version 3.6.1, but when I install the CRS-MSC module on the rear of the chassis, it can't be recognized by the system, the Alphanumeric LEDs on the front panel stuck in  'SP RMON' status, and when I use the command 'show platform' in the CLI, the output is:
    RP/0/RP1/CPU0:ios(admin)#sh platform
    Node            Type            PLIM            State           Config State
    0/0/SP          UNKNOWN(SP)     N/A             PRESENT         PWR,NSHUT,MON
    0/1/SP          UNKNOWN(SP)     N/A             PRESENT         PWR,NSHUT,MON
    0/2/SP          UNKNOWN(SP)     N/A             PRESENT         PWR,NSHUT,MON
    0/3/SP          UNKNOWN(SP)     N/A             PRESENT         PWR,NSHUT,MON
    0/4/SP          UNKNOWN(SP)     N/A             PRESENT         PWR,NSHUT,MON
    0/5/SP          UNKNOWN(SP)     N/A             PRESENT         PWR,NSHUT,MON
    0/6/SP          UNKNOWN(SP)     N/A             PRESENT         PWR,NSHUT,MON
    0/7/SP          UNKNOWN(SP)     N/A             PRESENT         PWR,NSHUT,MON
    0/RP0/CPU0      RP(Standby)     N/A             IOS XR RUN      PWR,NSHUT,MON
    0/RP1/CPU0      RP(Active)      N/A             IOS XR RUN      PWR,NSHUT,MON
    0/FC0/SP        LCC-FAN-CT(SP)  N/A             IOS XR RUN      PWR,NSHUT,MON
    0/FC1/SP        LCC-FAN-CT(SP)  N/A             IOS XR RUN      PWR,NSHUT,MON
    0/AM0/SP        ALARM(SP)       N/A             IOS XR RUN      PWR,NSHUT,MON
    0/AM1/SP        ALARM(SP)       N/A             IOS XR RUN      PWR,NSHUT,MON
    0/SM0/SP        FC/S(SP)        N/A             IOS XR RUN      PWR,NSHUT,MON
    0/SM1/SP        FC/S(SP)        N/A             IOS XR RUN      PWR,NSHUT,MON
    0/SM2/SP        FC/S(SP)        N/A             IOS XR RUN      PWR,NSHUT,MON
    0/SM3/SP        FC/S(SP)        N/A             IOS XR RUN      PWR,NSHUT,MON
    0/SM4/SP        FC/S(SP)        N/A             IOS XR RUN      PWR,NSHUT,MON
    0/SM5/SP        FC/S(SP)        N/A             IOS XR RUN      PWR,NSHUT,MON
    0/SM6/SP        FC/S(SP)        N/A             IOS XR RUN      PWR,NSHUT,MON
    0/SM7/SP        FC/S(SP)        N/A             IOS XR RUN      PWR,NSHUT,MON
    Can anyone tell me how to let the system recognized the MSC module, OR havd I done anything wrong?
    Thanks,
    Edwared.

    Thanks for your reply, Laurent Aubert, but I still have some confusion.
    You know, when I use the command 'show platform', the type of the card is 'unknown' and when I use the command 'show diag', the MSC module card didn't exist in the output like other type of card did, that makes me uncertain.
    My question is : How can I prove the MSC card is good and usable?  Just insert the PLIM.and MSC at same time? Is that the only way I can do?

Maybe you are looking for

  • How to reduce process time in report

    Hi all.. Is there any technique to reduce process time in report on programmer side?? Plz help me...

  • How do I change the default folder for saving contacts?

    I have happily used Outlook for several years for POP accounts.  My recent addition of an Exchange account has hijacked several default behaviors that I was used to.  For one,  contacts are now saved by default in the exchange related contact folder

  • Windows Xp Cannot Uninstall or Install Adobe Air.

    I installed a new application that when I booted it It displayed the "This application requires Adobe air wich cannot be found" error. I already have adobe air, so I tried installing the latest version of air (didn't work), then after that I tried un

  • Launch PowerPoint from within a Flash Document?

    I am new to this and have a question. Is it possible to launch a PowerPoint file from within a Flash Document? (It can open either internally or externally) And, if so, is there a simple way to do it, or can you give me directions to the proper tutor

  • Case statement 'when IN cursor'

    Hi folks. I am wondering if it is possible to use the IN command within a CASE statement? I am trying to see if a parameter falls under certain dates in another table. I have a cursor declared which points at that column of dates, and my case stateme