Does the Digi@nywhere A/D Plus work with PCI Express ?

Hi guys!
I am planning to purchase a Digi@nywhere A/D Plus for my PC,
but all PCI slots on my K9N Diamond mainboard are already busy,
only the second PCI Express slot which can be used for a second
graphic card in SLI mode (my mainboard uses nForce 590 SLI chipset)
is free to use.
Can the Digi@nywhere A/D Plus work with my PCI Express slot,
which is primarily intended to be used for a second graphic card in SLI mode,
or not ?

you cannot put a pci device in a pcie slot

Similar Messages

Does the "Mini DisplayPort to VGA Adapter" work with all Samsung tv models?

Does the "Mini DisplayPort to VGA Adapter" work with all Samsung tv models?

It's a VGA adapter. Nothing special about that. If your Samsung monitor supports VGA then it will work.
But why not go completely digital and use a Mini DisplayPort to HDMI adapter to skip the analog conversion? It also supports passing audio over HDMI.
About Mini DisplayPort to HDMI adapters

Does the QT MPEG2 Playback Component install & work with QT X ?

I am installing a new iMac with Snow Leopard.
Does the QT MPEG2 Playback Component install & work with QT X ?
(btw, I have already done the optional install of QT7 from the SN DVD).

Does the QT MPEG2 Playback Component install & work with QT X ?
I cannot get "muxed" MPEG2 content (e.g., VOB) file to load in QT X but both QT 7 Pro (with usual audio limitations) and MPEG Streamclip still function normally under Snow Leopard. (Since I don't normally use QT X, I had to actually run a quick test to see what would happen and haven't really performed any real tests. So take my comments with a grain of salt at this time.)
with such files on my PB Pro.

Does the Wacom Intuos Creative Stylus 2 work with Adobe Draw

Does the Wacom Intuos Creative Stylus 2 work with Adobe Draw?

IP,
I believe you should ask over here:
Adobe Illustrator Draw

Does the new command 2 binary format work with Apple Push Notification Service? I receive an invalid response status code of 128.

Does the new command 2 binary format work with Apple Push Notification Service? I am sending 2 messages with the same payload to 2 different devices. None of the messages display on either of the devices. It seems that at least 3 should have been displayed. For my first device, I received a response with an invalid status code of 128 and the message identifier is 2 indicating that the first message was OK. However no message was displayed on the phone. For the second device, I did not receive any error response, but no message was displayed on the device.
Does ANS perform any validation on the message identifier? The Local and Push Notification Programmin Guide says the message identifier is:
An arbitrary, opaque value that identifies this notification. This identifier is used for reporting errors to your server.
I know that the device tokens are valid because the same tokens work when I use the legacy basic or enhanced formats. The phones display the messages correctly when I send to ANS using the old ANS message format.
Here is the data and the response:
Sent to ANS: 2 0 0 0 158 1 0 32 120 107 166 143 171 157 143 169 70 135 12 135 246 142 64 224 244 44 116 4 154 65 115 192 206 28 189 56 174 0 172 16 2 0 23 123 34 97 112 115 34 58 123 34 97 108 101 114 116 34 58 34 65 66 67 34 125 125 3 0 4 0 0 0 2 4 0 4 83 7 119 141 5 0 1 5 1 0 32 120 107 166 143 171 157 143 169 70 135 12 135 246 142 64 224 244 44 116 4 154 65 115 192 206 28 189 56 174 0 172 16 2 0 23 123 34 97 112 115 34 58 123 34 97 108 101 114 116 34 58 34 65 66 67 34 125 125 3 0 4 0 0 0 3 4 0 4 83 7 119 141 5 0 1 5
ANS returned an error: 8 128 0 0 0 2
Sent to ANS: 2 0 0 0 158 1 0 32 4 239 182 26 13 237 170 136 41 243 181 57 120 208 135 19 101 102 212 70 55 244 251 255 160 125 82 9 10 143 72 17 2 0 23 123 34 97 112 115 34 58 123 34 97 108 101 114 116 34 58 34 65 66 67 34 125 125 3 0 4 0 0 0 5 4 0 4 83 7 119 147 5 0 1 5 1 0 32 4 239 182 26 13 237 170 136 41 243 181 57 120 208 135 19 101 102 212 70 55 244 251 255 160 125 82 9 10 143 72 17 2 0 23 123 34 97 112 115 34 58 123 34 97 108 101 114 116 34 58 34 65 66 67 34 125 125 3 0 4 0 0 0 6 4 0 4 83 7 119 147 5 0 1 5
ANS did not return a response.

Hello, can you please help me ?
You specified sample payload here:
TerrellFromLockhart wrote:
I finally got this to work. The picture in the Programming Guide is very confusing. The solution was to prefix every message's frame data with command 2 and that messsage's frame data length. Here is a sample:
ANS frame: 2 0 0 0 77 1 0 32 120 107 166 143 171 157 143 169 70 135 12 135 246 142 64 224 244 44 116 4 154 65 115 192 206 28 189 56 174 0 172 16 2 0 21 123 34 97 112 115 34 58 123 34 97 108 101 114 116 34 58 34 63 34 125 125 3 0 4 0 0 0 2 4 0 4 83 7 199 195 5 0 1 10 2 0 0 0 77 1 0 32 120 107 166 143 171 157 143 169 70 135 12 135 246 142 64 224 244 44 116 4 154 65 115 192 206 28 189 56 174 0 172 16 2 0 21 123 34 97 112 115 34 58 123 34 97 108 101 114 116 34 58 34 63 34 125 125 3 0 4 0 0 0 3 4 0 4 83 7 199 195 5 0 1 10 2 0 0 0 77 1 0 32 120 107 166 143 171 157 143 169 70 135 12 135 246 142 64 224 244 44 116 4 154 65 115 192 206 28 189 56 174 0 172 16 2 0 21 123 34 97 112 115 34 58 123 34 97 108 101 114 116 34 58 34 63 34 125 125 3 0 4 0 0 0 4 4 0 4 83 7 199 195 5 0 1 10
About to read response at Thu Feb 20 15:40:20 CST 2014
SocketTimeoutException
2 - is clearly command
0 0 0 77 - frame length
1 - item Id
what's 0 32 ? According to this page https://developer.apple.com/library/ios/documentation/NetworkingInternet/Concept ual/RemoteNotificationsPG/Chapters/Commu…
Item id should be followed by item length. But item length is obviously greater than 32 because device token's length is 32. Can you please explain why 0 32 were used? and do you have any insight on item id meaning ?

Does the DDL and DTS Connect Pack work with a X-Fi Xtreme Music UAA

? Hello,
hope u don't mind my English. I have learned it a long time ago, don't need it very often and the grammer was always my problem.
I know the patch works with a X-Fi Xtreme Music, but I am not sure about the UAA (what does this mean and do I need optical or coax out). I tried the titanium pcie before but then I have the skipping/lags effect like some others with Powerdvd9 Ultra as well. It seems that there is no workaround for this. I have no problems with my old X-Fi Xtreme Audio
Thanks in advance
scorpie
PS.
Maybe there is a workaround now but I can't find something
Some infos:
Board Asus P5B
2 Nvidea Gards 8800GT and 9500 GT (no SLI)
XP 64 bit SP3
8GIG Ram
LG GGC-H20L

SPDIF out has nothing to do with support. I have no idea what hte Xtreme Music UAA supports. I would imagine if it uses the DSP from the normal X-FI line, it would. If it uses the DSP from the Xtreme Audio, it won't.

Does the 27 inch iMac 3.2GHz work with a step approximated sine wave?

Regarding the 27 inch iMac 3.2GHz Intel Core i3 Apple Computer... does it work with a step approximated sine wave?

In configuring a UPS uninterruptible power supply with an iMac, APC asked, "Does the 27 inch iMac 3.2GHz Intel Core i3 Apple Computer work with a step approximated sine wave?"
References checked
http://store.apple.com/us/product/T6566LL/A
http://www.apc.com/products/resource/include/techspecindex.cfm?basesku=SUA1500RM2U
http://store.apple.com/us/product/H0880LL/A
http://www.apc.com/products/resource/include/techspecindex.cfm?basesku=BX1500G

Does the new Macbook Pro 13 2011 work with the Intel SSD?

I've been trying to upgrade my macbook pro to an ssd (using stock original 5400 rpm 320 gb HDD) but so far I've been reading for like 2-3 hrs and came to a conclusion. Intel is the most reliable and most highly recommended. However, Intel SSD doesn't work with the new Macbook Pro 13" & 17" because of some cabling SATA III issues. Does the issue still remain or has it been fixed? If it hasn't been fixed, what is the current most highly recommended and reliable and best in terms of speed, reliability, and just...best SSD available that works best with the 2011 MBP? Can anyone help me out? Ive been reading that OCZ and others are faster than Intel but less reliable (higher failure rates) and MBP can't take advantage of faster 6/Gbps RAID III or something. help me!!! Should I just wait?

If you search the web, you will predominately read about problems, not good experiences.
I don't believe Intel is any less subject to issues, than the Sandforce SSD drives.
Buy from a reliable source with a good return policy and warranty.
OWC is well regarded.

Does the Xbox 360 wireless adapter even work with the WRT54G wireless router?!!? If so, how???

I just bought a WRT54G wireless router (Ver 8.0; firmware updated to latest). I have successfully connected my wireless laptop using WEP security, but I'm at wits end trying to get the Xbox 360 wireless adapter to work. (It worked just fine with my Netgear router until that router recently died.)
When I do the "Test Media Connection" routine (you XBox 360 users know what I'm referring to), the Xbox immediately recognizes the Network Adapter and indicates that it is connected to the Wireless Network, but it inevitably fails the next step in the process: IP Address. I have the set-up for the IP address to be assigned automatically by the router (which is set for DHCP Server enabled).
I have gone around the mountain innumerable times myself and then with well-meaning friends who say try this, try that, try this, try that. I've had to re-establish my laptop set-up so many times I wanna scream!
Are the Xbox 360 wireless adapter and the WRT54G even compatible? If so, what am I missing here? I'm not too technical and obviously in over my head, but this ought not be that hard.
Please, please do NOT respond unless you KNOW the answer! I don't mean to be curt, but I'm over / past "suggestions to try."
Thank you VERY much for your time and consideration if you can help me.

I don't think that the X-BOX adapter is not compatible to wireless rotuer .... there are few settings you can try on the router ... Access router setup page ... Please click on the tab "Application and gaming" and click on sub tab "Port range forwarding" 1) On the first line in Application box type in "Xbox", in start box type in 88, in end box type in 88, in protocol keep it both, in ip address type in 192.168.1.20 and give a check mark on enable box. 2) On the second line in Application box type in "Xbox", in start box type in 3074, in end box type in 3074, in protocol keep it both, in ip address type in 192.168.1.20 and give a check mark on enable box. 3) Now save the settings 4) Once you return to the setup page, click on the tab "Administration" and disable the UPNP and save the settings. 5) Now assign the given ip address on your xbox ip address :- 192.168.1.20 subnet mask :- 255.255.255.0 default gateway :- 192.168.1.1 Please assign the dns address on the xbox primary dns :- 4.2.2.2 secondary dns :- 192.168.1.1 6) Please try to test your xbox live. Hope it works ...

Does the 1st generation apple wireless keyboard work with an iPad?

Hi
I want to get a keyboard for my iPad but I don't know if this one works with my iPad 2. Can someone help please??!!

Should work just fine, I have a 1G Apple wireless keyboard and it connected just fine to my iPad 3.
Any reason why you want to use a first generation Apple keyboard? They require 3 AA batteries and can drain them fairly fast. The second and present wireless keyboard only needs 2 AA's and the batteries last much longer. I use rechargeable batteries in my 2G keyboard as well and since my charger only charges batteries in pairs makes the 1G limited to alkaline batteries.

HT3546 Does the Airport Extreme Base Station not work with the OS X Lion?

Ever since updated to OSX Lion can't get our airport station to work. Is it too old and won't work with this upgrade so do we need a newer airport?

Suggest that you download and install AirPort Utility 5.6 for Mac OS X Lion which should work with your older AirPort Extreme.
You can keep both AirPort Utility 6.1 and 5.6 on your Mac and use the one that you want or need at the time.

Does the DCR-SR62 30GB Sony Handycam work with Final Cut Express hd 3.5?

Hi,
I am a new mac user and I want to get a good camera that will work with Final Cut Express hd, I am currently looking at the DCR-SR62 30GB and the HDR-UX1 dvd both by sony and I would like to know if these to cameras or one of them will work with Final Cut Express Hd. Thanks.

Niether one of these cams are the best choice for FCE. FC can not directly work with either DVD or HD (as in Hard drive) camcorders. You will have to convert and/or rip the output of either camera, giving you an extra work step and perhaps diminishing the quality of your footage
FCE is designed to work with DV/HDV material ... from a tape, throught a Firewire connection
There is software like MPEG Streamclip which will allow you to convert those cam's output to work with FC but if you haven't bought them yet, I would hold off and look at a good quality tape based cam

Does the Apple Snow Leopard install USB work with any macbook air?

Hi guys and girls,
Im changing the hard drive in my MBA 2008 A1237 from the 80GB HDD to the 64GB SSD. Ive seen a Snow Leopard install usb on ebay for £15 so ive brought it.... but I was wondering if it would actuly work with my particular Air?
As my perivouse exspriance tells me that some install DVDs are tied to cirent products such as my iMac install dvd wont work on my Macbook..
Thanks
Firky

The OS X Lion Thumb Drive isn't being sold by Apple, so you need Snow Leopard. Buy Snow Leopard from Apple and use the USB SuperDrive to do it. Then, open Apple menu > Software Update and install the most recent version. If you don't want to spend more money, stay in Snow Leopard, but if you want Lion, call Apple to purchase Lion > http://support.apple.com/kb/HE57

Does the BO Sharepoint 2007 Integration kit work with Sharepoint Serv 3.0?

Hello,
I have seen several posts about this topic but I still have not come to a correct conclusion. I have Windows Sharepoint Services 3.0 and BO Crystal Reports Server XI R2 SP3. The getting started documentation for SP3 specifically says the portal integration kit can be used with "MS Windows Sharepoint Services or Sharepoint Server 2007". However when I try to install the the integration kit I receive an error "Microsoft Sharepoint Server 2007 is required to install the Microsoft Sharepoint Integration Kit".
Is this true? Do I have something setup wrong or is the documentation incorrect and only Sharepoint server 2007 is supported?
It shows WSS as compatible in this document http://www.businessobjects.com/pdf/solutions/microsoft/bo_microsoft_interoperability_final.pdf
Any clarification would be helpful as I have wasted 1+ days trying to figure this out. I just need to know if Sharepoint services and the Sharepoint integration kit will work together with Crystal Server XI R2 SP3.
Thanks,
Ryan

Hello Ryan,
I recommend to post this query to the [Integration Kits - Other|BusinessObjects Integration Kits; forum.
This forum is dedicated to topics related to the other BusinessObjects Integration Kit.
This forum is dedicated to topics related to other BusinessObjects Integration Kits, including Siebel, Baan, PeopleSoft, and JD Edwards.
It is monitored by qualified technicians and you will get a faster response there.
Also, all SAP Kit queries remain in one place and thus can be easily searched in one place.
Thanks a lot,
Falk

SoundFX suddenly not working with PCI-Express SB Titanium and Windows 7 HP 64

Hi guys,
I bought myself a PCI-Express Sounblaster Titanium bulk last friday.
I downloaded some drivers (sorry, I have no idea what Version?) and an Update to the latest official Version (2.7.0007). When I first tried tu use VoiceFX it worked and I was astonished. Its seemed a real cool gimmick.
Strangely, when I tried it again the next day the VoiceFX buttons where still there under the Audio Config thingie, but my voice did not change anymore when I chose for ex. Robot or Ork. It did not matter what I chose, my voice always stayed normal.
Since then I've deen doing nothing else than to deinstall, reinstall drivers, deleting driver traces, trying again. My worst case was that the VoiceFX did not show at all anymore, my best case was as described above.
I even treid the new beta Drivers.
Does anyone have a solution?
If not, can anyone tell me what dependancies VoiceFX has? Is it enough to install only the drivers or does it need something else as well?
With which Driver Version does it definitely work under Win 7 64?
Oh yeah, I have I microphone which I can switch to Mono or Stereo, does it only work with one of the two? Mine was mostly in Stereo mode. (It comes from a company (dunno which one) thats got nothing to do with computers, games or creative, it's one of those Microphones you connect to your tie).
Thanks@all

Weird... I changed nothing and yeterday it worked...
I just understand this, but what the hell?

Does the Digi@nywhere A/D Plus work with PCI Express ?

Similar Messages

Maybe you are looking for