Does WBP54G work with Wireless Routers

I have the Dlink DIR 655. Can I use this with my Sipura Telephone adapter? Please advise.

The wireless connection should work fine (provided that the signal path is adequate, there is no harmful interference from other devices such as 2.4 GHz cordless phones, etc.) Also, note that the DIR 655 has an ALG for SIP that is incompatible with some ATA setups. This trouble, if it occurs, would also happen if you used a wired connection. It's usually possible to fix the problem by disabling the ALG or setting up port forwarding, but if you have other VoIP devices connected to the same router, there may be a conflict.

Similar Messages

TS3276 when I use cable my mail does not work. with wireless ok

when I use cable my mail does not work. with wireless ok

Unpower and restart it. If that doesn't help, try holding menu and left navigation keys TOGETHER for 6 secs.
AC

I have wireless mouse does not work with boot camp

i have wireless mouse does not work with boot camp

Did you install the correct driver for your Windows version? Are you saying the mouse does not work in Windows after Windows is installed?

Does Dictation work with a bluetooth wireless microphone?

I am deaf. Dictation helps by allowing others to speak into the built in microphone on my iMac and then let me read what they said. It would be much easier if they could use a wireless microphone. So,1) does Dictation work with a wireless microphone, and 2) does anyone have a recommendation for a good quality wireless microphone that is compatible with an iMac 3.4 Intel Core i7?

It sould work just fine. You would have to go into system preferences/sound/input and make sure the wireless mic is the defult input. As far as a good wireles mic I have no recomendation. I would check and see if there are any on the Apple store. Hope that helps.

My Time Capsule does not work with existing WiFi

Following a question solved on March 24 by LaPastenague, but gone bad again.
Apple AirPort Time Capsule
I felt the need for a physical backup of my data, as I would not completely trust the different clouds. I use, and have used Dropbox for 4-5 years and are very satisfied with that, but I am still not sure if or when a political lunatic will shut off the internet.
I purchased the Apple AP Time Capsule 2T, because all my other stuff are Apple, and that it's wireless. My old backup is Maxtor 300 GB.
Since we stay 2-3 weeks on two locations, one in Norway and one in Sweden (two different countries) we must use Mobile Broadband 4G, cables or fibre connections are useless for us, and we don't have it up to the houses. I have one mini router for each country, we bring with us iPhones, iPads, iMac, Apple TV, APExpress. When we pass the boarder I change the mini router, and the system continues working perfect on the WiFi, except the APExpress that needs to be reconfigured, but then it works.
The APTC was difficult to make working as it would not accept to be in an existing network, but with good help from the Apple Community, LaPastenague, with forcing the TC connect to the APE with Ethernet cable in bridge mode, ref "My Time Capsule does not work with existing WiFi" from March 24, the problem was solved and all gadgets worked together in a perfect harmony, until we changed location.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
I have a slight feeling that the two WiFi bands are making the trouble as during the configuration of the TC sometime the last figure 6 and 7 pops up, and that has something two do with the two different 2,4 and 5 GHZ bands
So, I am curious if you have any idea ?
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?

I can deal with the last question first and easily.
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?
Open the airport utility .. go to the disk tab and select erase.
When you select erase you will get mulitiple options.
Quick removes the file table but does not delete the files,, it takes 2min or less.
A Zero out data is the secure way,, by writing 0 ie low level drive format.
It can take several hours..
7 pass will take a week.. not recommended..
35 pass erase is ridiculous.. it would take a month.. put an ax through the TC. It is quick and better.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
The fact that it did work and has now failed might point to faulty unit.
The only way to tell is reset it properly to factory and start over.
Universal Factory Reset.. any model TC or AE.
Unplug your TC/AE from power or turn off at the power point.
Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Note..
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Generally having multiple wireless AP should not cause problems.. but it is better to set channels manually.. so it doesn't go beserk rotating channels.
Remember to keep all names short, no spaces and pure alphanumeric.
Sadly though the Apple routers have no logging now and no SNMP and almost nothing to help diagnose a problem, so if it continues .. take it back to apple.. they have given you no other method of fixing it.

APPLE TV DOES NOT WORK WITH NETFLIX

APPLE TV DOES NOT WORK WITH NETFLIX, just a black screen and "Netflix is loading" message appears. I can´t even see Netflix´s home page or set up my account. Netflix is working fine on all other devices at home, but in Apple TV.
I have tried the 8.8.8.8 DNS trick, the turn off procedure, the manual IP setting, but nothing....black screen still appears

It started working.....!!!!! (It seems someone back there is listening)
I "forced" an upgrade, I mean it showed "AppleTV is updated", nevertheless I re-started the system using the "return to original configurations" option. Then it updated again by itself to a newer version....and started working perfectly.
I have paired my apple wireless keyboard and it works fine, this way is easier to set up passwords or so (you can also do it with your remote).
TIPS:
I didn´t change any language or video quality configuration (scared to do so)
I changed to ethernet (cable) instead of wireless
My internet plan is 6 Megabytes (it was the same while it wasn't working)
good luck!!

Should my iPhone 1 (iOS 3.1.3) with Bluetooth 2.0 (Handset HSP?) work with wireless earbuds with BT 4.0 and the Headset (and Handsfree, A2DP, AVRCP) protocol? They pair and connect; status bar looks good. But audio always comes out the speaker. Thx.

Should my iPhone 1 (iOS 3.1.3) with Bluetooth 2.0 (Handset HSP?) work with wireless earbuds with BT 4.0 and the Headset (and Handsfree, A2DP, AVRCP) protocol? They pair and connect as expected (with a PIN); status bar looks good and shows Bluetooth active, and I even see the iPhone displays the battery levels of the wireless earbuds. But audio always comes out the speaker. (If I plug in wired headphones into the headphone jack then audio comes into the wired headphones, as expected.) I have rebooted the iPhone; I have had it forget about the wireless earbuds, and repaired and reconnected; I have reset all network settings. Thx in advance.
PS: I understand that more recent versions of iOS have a way to choose where audio output goes (speaker, headphone jack, Bluetooth device). Does this older version of iOS? I could not find an option or setting.

I've noticed this lately as well, with my iPhone 4. I couldn't confidently pin it directly on any particular iOS update, but my iPhone used to automatically connect up via Bluetooth with my Prius's handsfree feature, and now it doesn't. I work with a CE-based device at my job, with Bluetooth capability, and I used to test out that feature by having it discover my iPhone. This no longer works either.
What I have found (not really a solution, but it does work and may be a clue for Apple) is that if I simply go to the Settings app then the General -> Bluetooth screen and let it sit there, it will pair right up with my car within a few seconds. Bluetooth is always on, and always says "Now Discoverable" at the bottom of the settings screen.

AT&T Microcell does NOT work with Time Warner Technicolor Modem!

After a frustrating two weeks of working through problems with AT&T, trying to get my Microcell on-line, Time Warner finally informed me that the Microcell does not work with their new Technicolor modem. Incredibly annoying that none of the AT&T reps I spoke to knew this. I walked in the Time Warner office to swap out the moden, the clerk there immediately knew the problem because he use to work at AT&T. How a former AT&T rep knew this and none of the new ones did, is beyond me.

There are so many ISP configured routers and gateways out there that it is impossible for AT&T support to keep track of what is compatible and what is not. We are just starting to see reports of incompatibilities with the Technicolor gateways (TWC equipment has a long history of problems with the MicroCell). Unfortunately the support reps are limited in what they can tell the customer and unless AT&T documents and verifies equipment incompatibilites they can't say anything. What the "former AT&T rep" knew may have been in-house discussions. AT&T, like any provider, has to be careful not to immediately blame the other party without "proof". The more documented complaints AT&T receives concerning a specific piece of equipment the better. However, it is up to the ISP to fix and/or replace their equipment when it comes to compatibility problems. Specific firmware pushes for specific equipment by AT&T to the MicroCell is not a viable alternative nor is it realistic.

Ichat works with wireless, but not ethernet

Just moved into new office and bought new iMac. I can get internet with ethernet or wireless, but iChat works only over wireless. This is true with my intel Macbook as well. Is this a port or firewall problem, and if so, why would wireless work, but not ethernet?
Core2 Duo 24", 1 g ram Mac OS X (10.4.9)

Who is supplying the wireless internet connection?
Who is supplying the wired internet connection? If
it's two different entities, the IT Secret Police may
be blocking ports on the wired side.
TimeWarner comes in from the outside, but a private contractor is involved in the setup of the wireless which is connected to the TW modem. But if the wireless goes into the TW cable, why does it work as wireless, but not directly plugged in? It is as if converting the signal to wireless cures the problem.
Core2 Duo 24", 1 g ram Mac OS X (10.4.9)
Core2 Duo 24", 1 g ram Mac OS X (10.4.9)
Core2 Duo 24", 1 g ram Mac OS X (10.4.9)

Brightness control does not work with the bluetooth keyboard connected on my iPad2. Please someone could help me ?

Brightness control does not work with the bluetooth keyboard connected on my iPad2. Please someone could help me ?

Julien-
I have the Apple MC184LL/A Bluetooth Wireless Keyboard. The brigtness control works with mine, as do most of the other functions.
Try cycling the keyboard off and on. Hold the power button until the green LED goes out. Then press it one more time to turn it back on.
You might try resetting the iPad's network. Go to Settings-General-Reset-Reset Network Settings. Then you may need to reconnect your WiFi and Bluetooth.
If that doesn't help, try resetting/rebooting the iPad. Hold both the Home and Sleep buttons for several seconds until the Apple logo appears. Ignore the "Slide to power off" arrow. The iPad will restart in a couple of minutes. Resetting this way will not hurt anything, and sometimes clears up mysterious problems.
Fred

Does it work with hp printers

DOes this work with hp wireless printers

If your asking can the 802.11n AirPort Extreme Base Station (AEBSn) support HP wireless printers, then the answer is yes. I currently have my wireless HP Officejet 6500 printer connected to my AEBSn.

Does Lion work with an Epson Stylus Photo R2000 Ink Jet Printer?

Does Lion work with an Epson Stylus Photo R2000 Ink Jet Printer?

Took deliverly of my R2000 yesterday 11/04/2012.
**** of a job/mission getting to connect wirelessly to OSX Lion, but thanks to the perseverence of Epson support online chat plus ultimately phone call from Epson,the problem was resolved (total 3hours 45mins online chat 45mins on phone) yes i was a gineapig as the R2000 has only been available since March 2012 here in the UK.
1. Download combo driver/utilities for R2000 Mac 10.6 (works with Lion)
2. Install latest drivers and Epsonet.
3. Connect the printer to your wireless router using a LAN cable.
4. Ensure ink is installed on startup of the printer as the printer wont for some reason communicate without it as all the printer knows is it needs ink.
5. Ensure Mac is also connected to router.
6. Run Epsonet.
7. When Epsonet has found the R2000 click next.
8. Then click Changes on the following screen.
9. Select wireless Lan.
10. Select config manually (the auto will not work with Lion)
11. Allow Epsonet to use passwords from keychain network name(SSID) + WEP password.
12. When done you will be prompted to disconnect the LAN from the printer.
13. Then Click next.
14. Ensure wireless light on printer is lit if not hold WiFi button on printer for 3 Secs.
15. If config is successful (it took me Two attempts) goto system preferences/print/scan/Add printer and add the R2000 that ends in IP.
Hope this helps someone. Epson support is a good enough reason to buy Epson IMO as mentioned with their help it took nearly 4 hours to reach the above solution at no cost to myself and believe you me i was on the verge of returning the printer to the supplier as Wireless printing is a must with a 19 month old child on the loose.
Thanks Epson/Europe

I have recently upgraded my iMac Intel G5 iSight to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old sys parts

I have recently upgraded my iMac Intel G5 iSight (iMac5,1) to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old system parts. I have zapped PRAM. The blue indicator in system audio panel will appear for a second as I slide the bar for internal mic but then it disappears. Is there a fix?

The sound seems very faint but can here static on playback.

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed?

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed? I am using Firefox Beta for android and I also tried just Firefox.

Please check the Play Store app for any Flash updates and install them if present.

Flash player does not work with Ie or Firefox with win 8.1?

Flash player does not work with Ie or Firefox with win 8.1 64, If i try and play a video I get the message to install Flashplayer.
If I try and install it it says it is already installed. Your onsite installer says it is not applicable to my machine.
I have followed all the normal steps re enabling addons and active filters etc.
all to no avail Pc is Dell 6 months old, Flashplayer has never worked on this machine. Last MS update mid Dec 2014.
Version of flashplayer is 15....03.......

Flash Player is a built-in component of Internet Explorer. There's nothing separate to download or install.
Firefox requires a different version of Flash Player (the NPAPI plug-in), which will be served to you if you go here: http://get.adobe.com/flashplayer using Firefox; however, there are some unique stability issues related to Firefox on Win8.1, and you're probably better off using Google Chrome if you want a more optimal experience with Flash Player.
For problems where IE isn't being detected by sites that require Flash:
First, confirm that ActiveX Filtering is configured to allow Flash content:
https://forums.adobe.com/thread/867968
Internet Explorer 11 introduces a number of changes both to how the browser identifies itself to remote web servers, and to how it processes JavaScript intended to target behaviors specific to Internet Explorer. Unfortunately, this means that content on some sites will be broken until the content provider changes their site to conform to the new development approach required by modern versions of IE.
You can try to work around these issues by using Compatibility View:
http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-11

Does WBP54G work with Wireless Routers

Similar Messages

Maybe you are looking for