Does Y.1731 support for VPLS service under ASR 9000 platform?

Hi All,
we are planning to setup OAM for monitoring performance of our VPLS service interface? By checked Cisco document, I couldn't find related document that can confirm Y.1731 support multi-point to mulit-point interface by full mesh topology in our environment.
Does someone have this kind of experience that could share with me? The document or configuration example are welcomed as well.
Thanks in advance,
Eric.

thanks Xander for your input!
on top of this question. Actually, I am looking for better solution to monitoring mutli interfaces at same time. In our environment, we have many of this kind L2vpn setup for customer. instead of monitor end by end, we want to monitor them from central point of view. do you have a better idea for this?
I attached one customer setup example below, and diagram as well.
At the meantime, we also looking for a good idea for how to setup hierarchical monitoring system that it could cross other SP domain.
thanks,
Eric.
PE-siteA:
============
L2vpn
pw-class encap-mpls
encapsulation mpls
bridge group customer
bridge-domain customer
   interface GigabitEthernet0/1/0/1.100
   vfi 100
    neighbor PE-siteB loopback-IP pw-id 100
     pw-class encap-mpls
    neighbor PE-ASBR loopback-IP pw-id 100
     pw-class encap-mpls
=============
PE-siteB:
============
bridge group customer
bridge-domain customer
   interface GigabitEthernet0/2/0/1.100
   vfi 100
    neighbor PE-siteA loopback-IP pw-id 100
     pw-class encap-mpls
    neighbor PE-ASBR loopback-IP pw-id 100
     pw-class encap-mpls
=============
PE-siteC:
=============
bridge group customer
bridge-domain customer
   interface GigabitEthernet0/1/0/2.100
   interface GigabitEthernet0/5/0/2.100
   vfi 100
    neighbor PE-siteA loopback-IP pw-id 100
     pw-class encap-mpls
    neighbor PE-siteB loopback-IP pw-id 100
     pw-class encap-mpls
==============
PE interface setup:
==============
interface GigabitEthernet0/1/0/2.100 l2transport
encapsulation dot1q 100
rewrite ingress tag pop 1 symmetric
=================================

Similar Messages

Does Websphere(WAS) V3.5 has support for web services ??

Hi all,
Please let me know whether Websphere Application Server V3.5 supports Web Services. If any one has used it for V3.5 then please let me know.
Thanks
-Satyendra

I suppose not, as out of the box.
If you look into the classpath and the lib directories, there are no traces of any support for Web-Services.
However, you can set up the environment to do so, It seems to be easy to handle.
Cheers, and keep posting your progress.

Is there any commercial support for LCCS services? What are the associated SLAs

Hi,
Following are some queries regarding LCCS.
Is there any commercial support for LCCS services? What are the associated SLAs of the support and the cost?
Can I Using applications developed using LCCS for commercial purpose?
Does Adobe allows its LCCS service customers to offer applications developed using LCCS API for 3rd party commercial usage.
Thanks & Regards
Amit

Hi,
We were selling LCCS to enterprise customer under a different licensing program, but have since stopped the sale of that.
You should check out this thread - http://forums.adobe.com/message/4110049#4110049 for a discussion on this.
Jeff

Does Azure give deals for their service to business incubator companies/incubators?

Does Azure give deals for their service to business incubator companies/incubators?

Hi,
You could refer to the azure enterprise information via http://azure.microsoft.com/en-us/pricing/enterprise-agreement/ .
Also, about azure service to business incubator, I suggest you could contact the azure support to for more details:
Please contact support team by creating a support ticket at http://www.windowsazure.com/en-us/support/contact/
Or if that doesn't work because you don't have an active subscription you will need to contact general customer support to have them create a support ticket for you
http://support.microsoft.com/gp/customer-service-phone-numbers?wa=wsignin1.0
Regards,
Will
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

OK, as always I waited before downloading a new OS and I sure glad I did. On the APP store I sorted comments by most critical...and WHOA...what is Apple doing? No support for Logic 9, MS Office? Is Apple only trying to reach the iphone/iTouch crowd? HELP!

OK, as always I waited before downloading a new OS and I'm sure glad I did. On the APP store I sorted comments by most critical...and WHOA...what is Apple doing? No support for Logic 9, MS Office? Is Apple only trying to reach the iphone/iTouch crowd? HELP! I was going to buy a new Mac pro & two 27" monitors but until I see some real problem addressing by Apple...I'll keep what I have and see how everything pans out. If anyone has any comments to ally my fears, I welcome them. I've been a devoted Mac user since 1993. 7500; G4; G5; and my latest Mac Pro...Where do I go? Again...HELP!

Hi there,
If you look through ALL the reviews, they are mainly good. I feel that Lion is an excellent upgrade, although not essential.
There have been some issues with MS Office, but right now, it is up to Microsoft to issue a Lion compatible update, which will come in time. Saying this, MS Office has been working fine on my mac, it seems to be an isolated issue.
Logic 9 seems like a strange issue. Again, an update looks to be coming soon, with Lion support.
I do not feel that apple only focusing on the iPhone and iPad user base. There are many features carried along, but the machine can still be used for pro tools and use just as well. It still is a fantastic, reliable, fast, easy to use OS, which I have had very few problems with. Some additions you may not use, but they don't get in the way. You will love the new Exposé, Mission Control, as it is great for pro users who have many windows open at once, and the new spaces. You may however, never use Launchpad, but you don't have to, just drag it away from the dock!
I really reccomend buying a mac with Lion, although if you are worried about bugs, wait a few months for the issues to be ironed out, and updates to be given. Because the update is so very cheap, I really think you can hardly go wrong. Try it out with your current mac, and if you like it, go ahead and buy your new ones.
Lion is fantastic, albeit maybe rushed.
Any other queries, just ask,
Nathan

ADF Mobile: JSON support for REST services?

Will the JSON format be supported for REST services using ADF Mobile? Is there a workaround for now that can be used?

For now you can write a Java class to communicate with your JSON service, and expose it as a data control.

Why does firefox drop support for a plugin with an update

Why the H*ll does Firefox drop support for a plugin when there is an update in Firefox.
FF4 has reported that 6 of my plugins that work fine in 3.6 are now not supported. !! This is a joke, and happens regularly.
As a user (a highly IT literate one) this is annoying and frustrating, and from a design standpoint, unprofessional.

Plugins as in Flash, Java, quicktime or such or do you mean Extensions ?
Plenty of Plugins seems to be detected and in use by Firefox 4.0 just fine according to your system details by your post.
If you meant Extensions then check for updates, look at addons.mozilla.org or the Extension homepage for to see if the author has provided a update.
Generally Extensions can need anywhere from a simple maxversion bump to a lot more for it to work properly on a new Major version of Firefox depending on what the Extension does.
It is professional actually as extensions that were not actually compatible may actually cause problems big or small if they were to still just ''work'' in a new Major version release so hence the need for them to be properly up to date on any changes and hopefully the extension author is quick about it.

Does jdk1.6 supports for MAC os also?

hi,
does does jdk1.6 supports for MAC os also? becuase we have implemented some of the methods of jdk1.6 in my application.for example to find the free space i used getFreeSpace() method of jdk1.6.like this i used some the methods of jdk1.6.
please clarify me regarding this?
how can we free space of windows,linux and mac os with java1.4 or 1.5?
does it possible with java to find the free space?
if not with which one can we find the free space windows,linux and mac os ?
i think with native code it is possible.
i f any person already impleamented to find the free space of windows,linux and mac o/s please give me the code.
thanks,
prasad

I gave you some time to either edit one of the duplicate posts out or point one to the other by posting a simple link, like this:
THIS IS A DUPLICATE POST. PLEASE DO NOT REPLY HERE -- reply to the other one instead at:
http://forum.java.sun.com/thread.jspa?threadID=5204340
But I guess it's too much to ask for you to have done that yourself, eh?

Can Cisco 7200VXR support for VPLS?

Hi all,
I check Cisco Nagivator Feature to find which IOS support for VPLS on Cisco Router 7200VXR and found that IOS image "c7200-spservicesk9-mz.122-33.SRD.bin" can do it as below;
- VPLS Autodiscovery, BGP-based
- VPLS Multiple VCs per Spoke
When I try to configure Virtual Forwarding Instance, it's not allow me to configure the above features (VPLS Autodiscovery: BGP Based, Manual Configuration of VPLS) and only support point-to-point configuration mode you can see it as below
R1#show version
Cisco IOS Software, 7200 Software (C7200-SPSERVICESK9-M), Version 12.2(33)SRD, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 23-Oct-08 12:58 by prod_rel_team
R1(config)#l2 vfi ?
WORD VFI name
R1(config)#l2 vfi VPLS_A ?
point-to-point Point-to-point configuration mode
R1(config)#l2 vfi VPLS_A point-to-point ?
<cr>
R1(config)#router bgp 100
R1(config-router)#bgp router-id 150.1.1.1
R1(config-router)#neighbor 150.1.12.2 remote-as 100
R1(config-router)#neighbor 150.1.12.2 update-source lo0
R1(config-router)#address-family ?
ipv4 Address family
ipv6 Address family
l2vpn Address family
nsap Address family
vpnv4 Address family
vpnv6 Address family
R1(config-router)#address-family l2vpn ?
vpls Address Family modifier
<cr>
R1(config-router)#address-family l2vpn vpls ?
<cr>
R1(config-router)#address-family l2vpn vpls
% BGP: Error initializing topology
R1(config-router)#
I can use "l2 vfi VPLS_A point-to-point" for Layer 2 VPN Pseudo-Wire Switching but not for VPLS multipoint configuration mode. Can Cisco 7200VXR support VPLS on this IOS image? If it can't, which IOS image can do it on this platform.

VPLS is not supported on 7200, you can configure point to point here but not point to multipoint, you will have to move to 7600 for that.

Rep. does not have support for Oracle Designer

We're new to SCM and just useing SCM with JDeveloper.
Sorry for newbie stupidness. Searches of this forum didn't
turn up any hits on 21247 or other strings.
Given: brand new install of SCM. Created a private workarea
with RON. Attempting to use RAU to enable branching and
versioning.
I'm having some chicken-vs-the-egg problems. I can't
enable branching in my shared workarea with RAU because it
seems to want to pop up the Migration Dialogue and then
this error occurs:
CDR-21247: Error Cannot proceed!
The target repository does not have support for Oracle Designer
objects
Any help or tip would be greatly appreciated.

Curt,
If you managed to create a private workarea from the RON then versioning is enabled. You would have enabled this from the RAU.
Oracle 9i JDeveloper release candidate provides a wizard to create the workarea and private branch.
There are now two flavours of the repository, one with Designer + file and folder support and one with just files and folder support.
If you have no structured Designer components you do not require the Designer support to use JDeveloper with Oracle SCM.
I suggest you try the JDeveloper wizards. The RAU also offers a menu to examine repository object state. Check that you have no invalid
objects, they can be recompiled using the RAU.
David

Does LabVIEW have support for entering Urdu language script?

Hi All!
My LabVIEW application requires users to enter their observations in a string control which is then stored in an excel file.
Now the issue is that the user wants to enter the data in Urdu language.
Now my question is, Does LabVIEW have support for entering Urdu language script in a string control?
If yes how can I implement this? If no, is there any possibility that National Instruments could extend some help in this regard upon request?
Regards,
Reeves

My experience from Hebrew, which is also right to left, is that it can be done if the operating system supports it, but it will work badly if you include anything in the text which is not an Urdu letter. This causes it to be displayed in the wrong side of the control and is only solved if you add more Urdu text after it.
One option you can try is including an ActiveX control (such as the rich text box) for editing the text and then you can probably get the text from it using a property. I don't remember trying it (my users don't usually need to input Hebrew text themselves), but I think it should work. I wouldn't have any hopes for NI doing anything about this, because it's considered to be a relatively small market.
Try to take over the world!

Why Apple does not offer support for linux?

We all know the history of Apple. It clearly shows a trend to be open source, excepting for the licenses they share with Microsoft. In my personal case, I love open source because it has solved several of my problems. Just to share this with everyone, I am the network manager of a educational institution and I used to have my servers running on windows platform. Since we used to buy it all from Microsoft, they would give us free software for or labs, software like Visual Studio. They even assigned us engineers to plan everything for our servers, free of cost. Guess what? It was a disaster. We had our database destroyed by an external attack. We were “lucky” to have Microsoft in our servers and in our firewalls.
We had to take action, so I decided to switch to Debian, and to use IPCOP (a great dedicated firewall, if there is anyone interested, the link is: http://ipcop.org/ , please note, I am NOT affiliated with them, and I will receive no compensation or benefit if you chose to access it or not ). Both open source. The result, no external attack has been able to pass trough. After that, we switched most* of our e-learning platforms to open source, and guess what? We are saving over 60,000 yearly just in software. So for those who are looking for a good way to get good security without loosing an eye, try open source.
Now back to the point, I do not fully support any operative system. They all have their good features, or at least they should. The ones I know, are because I use them. My home network is composed by computers running in five different versions of Linux, two running in Mac OS X Tiger, and some others running in XP pro. My main computer is running in Ubuntu, and is really sad to see that there is no software from apple available for Linux. That is honestly the worst part of Linux, having no iTunes or QuickTime available. No way to see multimedia in the web, etc. A suggestion for apple would be, give support for Linux, there are a lot of us wanting the same.

Apple makes software and hardware. Therefore they
offer a total solution. Now they even can have
windows xp running on their hardware. Making a
version of mac os to run on linix isn't practically.
Under a mac is unix and you can run unix software
with the mac so you could do ever thing you are
doing with a mac.
I did not know Linux was one type of computer, like Mac...
Next topic, If I was willing to pay for it, this thread would not exist, because I can actually use a commercial software to adapt the windows web plug ins to Linux... If I was in charge of Apple, I would propose to develop free software support of my products, - plug ins and so - to other operative systems... But of course, even if I did, it would not be up to me. It would have to pass trough several layers of bureaucracy, and it would take a lot of time to be approved or rejected.
Anyway, the main issue is, the three most important OS's are Windows, Linux, and Mac. And that can't be denied. Now you can even run Windows in a Mac PC, and vice versa... besides being fancy, what else could I do with a Mac PC using Windows, when I can build a machine able to run Windows for less than 300 bucks? OK if you want to try a Mac in a i386 or a x86... but I still rather to be the proud owner of a PowerMac G5 than the owner of a Pentium 4 / AMD using Mac OS.
Also, I thought it would be fun to see the reactions and opinions of other people with this topic, hence, I was not expecting anyone from Mac to read it, and really do something about it, because I know they won't.

Performance Point 2010 Support for Analysis Services 2012

Can someone tell if me Analysis Services 2012 is support for PerformancePoint 2010 (SharePoint Server 2010). Could not find a definite answer when I search the web.
Thanks,
Don

Yes, you need to install the right ADOMD client and OLEDB Provider on SharePoint servers.
Install the Analysis Services OLE DB Provider on SharePoint Servers
This post is my own opinion and does not necessarily reflect the opinion or view of Slalom.

U510 - does Lenovo offer support for standard issues?

Hi, I wonder if Lenovo offer any support for the very common issues that this product of theirs has?
1. This products energy management reacts to low battery by shutting down the wifi totally, and you ar not able to turn it on again in other ways than recharging the battery to a high percentage, plus shutting down and restarting the computer totally. This is incredibly disturbing, almost as disturbing as the fact that Lenovo seems to have put no effort in solving the problem. Does Lenovo not have aim to help its customers with this? No updates in the energy management system? No work-arounds? Some users say they have uninstalled Lenovo Energy Management 8 and installed version 7 but it does not install on my Windows 8.1.
2. This product has what Lenovo calls a "Mini-VGA" port. With my U510 there came an adapter for connecting standard VGA cables to the port. It did not work and I have found no evidence of anyone getting it t work, only problems with it. And not a single answer regarding the problems by Lenovo? Has anyone got an answer about how to get it to work, or has someone found that their mini-VGA works with an adapter? Did anyone get help by Lenovo? (Not me) Please share if !
3. The Touchpad of this computer might work in the beginning (or at least I have found some posts claiming that it did) but most seem to have the same problem as me, the touchpad being very coarse and clumsy, running away and not reacting to right-button clicks very often. I have found no answer by Lenovo regarding this problem. Getting a physical guarantee service would have taken more than a month, a time lapse which was impossible for me to take without a computer. Anyone got a software solution by lenovo for this one, or is it a physical error in this model?
Cheers Ben

answer to 2. if you had the adapter connected to your laptop and a cable from laptop to monitor make sure you press fn + f3 after that will let you enable so laptops screen appears on monitor or tv you connected to if it shows up as black pic

Flex/ActionScript3 support for web services using WS-Security

Does Flex/ActionScript3 have support for connecting to a web
service using WS-Security (Policy Creation). I've tried using the
Flex Data Service "Import WSDL" method and it does not allow me to
connect. Is there Flex/AS3 package that can handle creating the
Policy information for a web service that utilizies WS-Security?
Thanks,
Tom

quote:
Does Flex/ActionScript3 have support for connecting to a web
service using WS-Security (Policy Creation).
Yes and no. The "Import WSDL" doesn't create AS3 classes that
allow header injection of the appropriate WS-Security elements.
I've managed to work around this using straight mx:webservice tags
and AS3. There is an open bug at
https://bugs.adobe.com/jira/browse/SDK-15398
that I voted on, the more the merrier.
http://www.jroller.com/wookets/entry/ws_security_in_flex
Has a useful class for creating the soap header elements for a
username token,
In general though, it's been a challenge to get the simplest
of WS-Security pieces working.
-Brett

Does Y.1731 support for VPLS service under ASR 9000 platform?

Similar Messages

Maybe you are looking for