Does your elicenser usb is always plugged in?

I have my registered licence of nexus2 on the key which is always plugged in my MBP.
but when I unplug my elicenser usb key , logic doesn't open.
I'd like to save the license of nexus in my computer without letting the usb plugged vecause it's wasting a usb slot on my mbp
Can I do that ?
thanks for your help

Hi, schubyOne.
The elicencer will offer you a choice when you first get a new licence to either put in on a usb or install a software licence [ a soft licence] onto the computer itself.
When the program starts you should get a box with info about managing, getting new licences or transfering them.
The transferrring section is what you want. It says drag the old licence onto the new destination and follow thr prompts.
If any of this doesn't make sense or you are unsure, contact elicencer support and they will help.
Good luck with it,
Regards,
Scorpii.

Similar Messages

HT2693 I purchased Huawei Dongle and trying to connect with my NEW MacBook Pro (OS- Mountain Lion) USB port 3.0 but unfortunately it does not support. When I plugged in my the power is flowing in dongle due green light blinking twice in every 3 sec but no

Hi,
I purchased Huawei Dongle and trying to connect with my new MacBook Pro (OS- Mountain Lion) USB port 3.0 but unfortunately it does not support.
When I plugged in my macbook the power is flowing in dongle due green light blinking twice in every 3 sec but no connection found or diver shown.
Please let me know how I have to use it. I got some suggestion for USB hub 2.0 but It does not make any sense and driver installation.
So please suggest proper direction to use it and provide link to install any driver.
Thanks
Tauheed Ahmad

Yes Clinton I did same, but they were (Huawei customer support) surprised about this problem, They behave like they have no idea about USB 2.0 and 3.0 knowledge. They handsUp that reason I posted my problem in this forum.
So is there any better solution to use any mediator between these USB version handling, Please let me know.
Thanks
Tauheed

Micro usb cord to plug in your appletv

If you need a micro usb cord to plug in your appletv to your computer, why did apple not include one in the box?

I quite agree - the lead would cost them probably a few pennies/cents to include, but if it is needed to get your AppleTV out of jail when it fails without returning it to the vendor/Apple store you'd think they would.
Also it would be the correct type of cable - not all carry data, some power only.
I have a couple of microUSB leads but they don't all allow me to restore - maybe connector tolerances differ slightly, but at least an Apple supplied lead should work.

Why does my Mac go black after plugging in USB?

My problem is, I wanted to download music and upgrade my iPhone with the USB so I plug it in an my screen turns black and wen I plug it in to charge it's blinking green very lightly. How do I make my screen visible again to see if the problems inside?
Please help I'm beginning to freak out nobody here seems to know the prob..
Thank you

What you describe sounds like a hardware issue. You need to get it checked out by Apple.

Trying to update apple tv (small black box). how do i do update? can't find system settings. i see system preferences no mac pro. does apple tv need to be plugged into hdtv for the update or PC. If PC, how?

trying to update apple tv (small black box). how do i do update? can't find system settings. i see system preferences no mac pro. does apple tv need to be plugged into hdtv for the update or PC. If PC, how?

You have to do it on the Apple TV itself while it's plugged into a TV so that you can see its screen.
I quote
How to update software on your Apple TV (2nd and 3rd generation)
Learn how to update the software on your Apple TV (2nd and 3rd generation). It's always a good idea to have the latest software on your Apple TV.
Update your software
Select Settings > General > Update Software. Apple TV checks for an available update; if one is available, a download message should appear.
Click Download and Install to start the download process.
Do not disconnect your Apple TV during the update process. The Apple TV status light may flash slowly during the update and restart process. This is expected behavior.

Always plugged in- Battery life

Hi
what will be the effect on my battery if its always plugged in to the charger. I am using my MBP more or less like a desktop these days. charging , removing & again putting the charging lead is frustrating & sometimes i just forget to take the lead out & its there all night.
what is the ideal recommendation.

Welcome to the Forums!
Apple recommends a full discharge-charge cycle at least once per month.
From http://www.apple.com/batteries/notebooks.html:
+For proper maintenance of a lithium-based battery, it’s important to keep the electrons in it moving occasionally. Apple does not recommend leaving your portable plugged in all the time. An ideal use would be a commuter who uses her MacBook Pro on the train, then plugs it in at the office to charge. This keeps the battery juices flowing. If on the other hand, you use a desktop computer at work, and save a notebook for infrequent travel, Apple recommends charging and discharging its battery at least once per month.+
Hope this helps...

Does Apple make a cord to plug a guitar into the iMac?

I saw an Apple tutorial video that showed a little white cable that a guitar could plug into. The male end plugged into the back of the Mac. Anybody know where I can get one, or what it's officially called? The local Apple store was no help.

That was probably an iMic - an audio interface that lets you connect your guitar to an USB port.
Does your guitar have a buit-in pre-amp? If not, you might be better of with an interface like the Apogee Jam.

Is it bad for my ipod to be always plugged to my bose sound dock?

I have it always plugged, and when I unplug it, it won't turn off and I have to reset it. Is it bad for the battery or for the ipod itself to be always plugged??
Thanks a lot.

It isn't bad for the battery
since the charging circuit will only charge the
battery if needed and turn off charging when not
needed, so it won't trickle charge the whole time.
My concern would be for the LCD backlight. It is on
all the time? Like any light, they have a limited
number of hours, either getting dimmer with time or
burning out. So you could be putting unnecessary life
time on the backlight. If it is on, can you go into
the settings of the iPod and turn it off? Or like
when syncing the computer, does the backlight stay on
regardless of the LCD backlight setting on the iPod?
Patrick
Hi Patrick,
Thanks for your answer. No, the backlight is not on, actually it turns off about two seconds after starting to play music or whatever.
My concern was because when I take the ipod off the speakers, I have to reset it to turn it off, but I guess it's something not bad for the ipod¿?
Thanks again.
Begoña

Does your Muvo Slim have this probl

When I have finished file transfer with my Muvo Slim, and disconnect the USB cable, sometimes ( out of every 3 times) the Slim will turn itself OFF (blank screen) and SOMETIMES it will turn itself on (the Creative logo displays, and then it starts to play a track.)
Has anybody else experienced any this erratic behavior?
Or, when you disconnect the USB cable, does your Slim always turn itself off, OR always turn itself on?
I contacted Tech Support, and they said I may have a faulty unit, and I am curious to see if this is happening with anyone else.
Incidentally, I am using the latest firmware version ..03.
Thanks in advance for any replies.
Miner2049er.
Message Edited by miner2049er on <SPAN class=date_text>03-03-2005<SPAN class=time_text>03:38 AM
Message Edited by miner2049er on 03-03-2005 03:38 AM

Yes, same problem with my unit too.

IPod does not respond at all when plugged in

Alright, this topic is for people who have had this exact problem only. I don't want to get this confused with other problems and have people trying to help troubleshoot multiple problems and get things mixed up. Here's the problem.
After updating to v1.1.2 of the iPod software, the iPod does not respond when plugged in. The iPod still works fine when not plugged in. It plays music and both the standard and shuffle play modes work accordingly. The problem is when you plug the iPod in, it doesn't charge and it doesn't mount. The orange blinking light does not come on. While plugged in, it works the same way as it does when you're listening to music with it. It's as if the iPod's USB connector is dead. Here is my original post and description of the problem.
Alright, so here's my story. I bought my 512MB Shuffle in April. It has worked perfectly fine since I got it. Last night, I updated to v1.1.2 of the iPod software, clicked no when it asked if I wanted to restart, added some songs to the iPod, then restarted. As of this morning, I went to listen to some music while out for a bike ride, and I was greeted with the red battery light. I thought it was a bit odd since I had left it plugged in overnight. I figured, what the heck, I'll just plug it in and let it charge when I get back. When I got back, I plugged it into my PC and left for a while. I came back later and went to grab my Shuffle and I noticed it was cold, which was unusual after charging for a couple hours. I plugged it back in, a bit frustrated, and it never came up in Windows. I looked at the iPod plugged into the back of my PC (a high powered USB port) and sure enough, no orange light. No lights at all. I can still slide the switch to one of the play modes (standard play or shuffle) and play music for a couple seconds before it stops and says the battery's dead again. It works.. I mean it turns on and plays music, it's just not charging or mounting when I plug it in. I tried multiple computers and USB ports, none of which worked. I would really like some help with this considering it IS my only source of portable music and I'm not going to go pay $50 to talk to tech support or have it sent in for repairs. That's half of what it's worth.
I've tried uninstalling all iTunes/iPod related software from the PC I normally use it on and reinstalling it. That didn't work. I also tried uninstalling again and installing the last known working version of the iPod software, still no results. The only thing I havn't tried is giving it a good beating... Not that I would. Anyways, I hope there's a solution to this that doesn't involve buying a new one.
Here's a rundown of the computers I tested it with.
500MHZ G4 Cube (384MB RAM/Mac OSX Tiger)
400MHZ G3 iMac (384MB RAM/Mac OSX Tiger)
4.2GHZ AMD 64-Bit running Windows XP Service Pack 2 (my PC)
515MHZ Dell running Windows 2000 (256MB RAM)
UPDATE: The BIOS won't recognize the iPod, so it has nothing to do with my computer. Somehow, installing v1.1.2 of the iPod software made it so the iPod itself has USB problems. The iPod works to the extent of playing music and showing the battery charge level. I get no response at all when I plug it in, from the computer or the iPod.
I'm going to have to agree with Philip Harhay on this one. The original 10GB iPod I bought 3 years ago came with a full one-year warranty, no extra charges. I am disappointed to see the Shuffle only coming with a three-month warranty.
------------------------------------------------------------------

Help! I just purchase an iPod Shuffle for my son's birthday and I cannot get the darn thing to show up on my iMac G5. I am running OS 10.4.2 and I have downloaded the latest iPod and iTunes software. When I try to restore my iPod to the factory settings it tells me to plug the iPod into the computer, but it is plugged in. I have tried different USB ports, too. I'm running out of ideas and so is the trouble shooting Apple site. I was hoping someone out there might have some ideas.
It showed up at first and I transferred a few songs from the iTunes to the iPod but I couldn't get them to play, so I plugged it back into the USB and the icon never came up.

Cannot create your bootable usb stick

Hi all,
I'm new to bootcamp and I have the following problem:
When I'm creating a Windows 7 usb drive, it gives me an error "Cannot create your bootable usb stick there was a problem copying files".
I've tried searching google for the problem, but the only possible solutions I've got was to unmount the iso image and try again, but when I do that I still get the same error and when I check the disk utility I find the iso image is mounted again.
Does anyone haven an idea about what to do.
Specs:
OS X Yosemite 10.10.2
MacBook Pro Retina 13-inch Mid 2014
2,6Ghz Core i%
8 GB 1600 MHz ddr3
Thanks in advance!

Please see the Microsoft reference and the second link has an example.
https://support.microsoft.com/en-us/kb/841290?wa=wsignin1.0
Bootcamp Windows 8.1 "No Images Are Available"

My ipod will not charge from a wall socket but will charge using the same cable if the usb end is plugged into a computer or an airport power source. My iphone and ipad charge fine on the same cable usin ghte same wall plug in the same wall socket?

My ipod will not charge from a wall socket but will charge using the same cable if the usb end is plugged into a computer or directly into an airport power source. My iphone and ipad charge fine on the same cable using the same wall plug in the same wall socket. This makes no sense but I see that it has been posted as a problem elsewhere. This must be due to some kind of degredation of the Ipod. . It is not fixed by IOS resets as others have noted.
Has anyone asked Apple directly about this?

Hi there Apples or Pears,
I would recommend taking a look at the troubleshooting steps found in the articles below.
Charging your iPod battery
http://support.apple.com/kb/ht1384
iPod's battery doesn't charge
http://support.apple.com/kb/ta44551
-Griff W.

After sleep, retina MacBook Pro (Mid 2014) does not recognize usb connected mouse movement

After sleep, retina MacBook Pro (Mid 2014, on 10.9.4) does not recognize usb connected mouse movement. I have tried a generic usb mouse and my Razer Deathadder usb mouse. Both mice work before sleep; but after sleep, the computer no longer recognizes mouse movement while still recognizing the mouse buttons when pressed. Any idea why this is occurring?

Hello, chocotac0.
Thank you for visiting Apple Support Communities.
Here are some troubleshooting steps that I would recommend when experiencing this issue.
OS X Mavericks: Reset your computer’s PRAM
http://support.apple.com/kb/ph14222
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/ht3964
OS X Mavericks: If a USB device isn’t working
http://support.apple.com/kb/PH13876
Cheers,
Jason H.

My av adaptor does not work. Tried to plug my ipad into my samsung hd tv and ipad said it does not support that accessory...help

My av adaptor does not work. Tried to plug my ipad into my samsung hd tv and ipad said it does not support that accessory...help

What ipad, which model samsung? Are you attempting HDMI, VGA, or an RGB connection. Ipad 2 supports mirroring into an HDMI at an output of 1080. Ipad 1 is limited to only a few apps capable of the output, such as Youtube.
page64,65 of the latest ipad manual has more details.
Samsungs are good and should switch with the input - but sometimes you will have to select from the menu manually.
If in doubt, contact the customer support at samsung UK.
Also check - Settings/Video, that you have it enabled for Home Sharing. Apple Id which will be your .me.com email plus your apple ID password. I am not too sure about this as I cannot remember the exact order I set things up in - but page 89 of the manual references Home Sharing for sharing ipad/itunes content on a home pc/mac - so I would think it applies to content relayed to a tv or monitor too.

ITunes does not start automatically when I plug in my iPHONE. When I start it manually it does not recognize my phone although the phone is visible in My Computer.

Itunes does not start automatically when I plug in my iPhone. When I start it manually, it never recognizes the phone although it does ask if I want to download pictures etc. Many albums have no art work that use to. iTunes completely unresponsive to the mouse.

Hi billm1013,
I'm sorry to hear you are having these issues with your iPhone. If your iPhone isn't being recognized in iTunes, and/or iTunes isn't responding to your mouse when the iPhone is connected, you may find the troubleshooting steps outlined in the following article helpful:
If you don't see your connected device in iTunes for Mac - Apple Support
Regards,
- Brenden

Does your elicenser usb is always plugged in?

Similar Messages

Maybe you are looking for