Don't dowload airport utility 6.0 if your network is using old tethered airport expresses. Download Airport Utility 5.6 instead

Watch out for the new airport utility software update 6.0 if your airport express has any old hardware on it . It will no longer be supported . Plus it requires Lion to work ( Lion is not expensive to buy /download from App Store.) Good news though is that Apple has created 5. 6 that can be downloaded and will still allow you to tether (via ethernet cables) old airport express units.

Similar Messages

I have an old 1st gen express. Airport utilities 6.3 won't set it up. How do I set it up in Mountain lion?

I have an old 1st gen express. Airport utilities 6.3 won't set it up. How do I set it up in Mountain lion?

I have an old 1st gen express
Please check on the side of the Express and locate the Model No.
A 1st Gen AirPort Express is Model No A1264.
AirPort Utility 6.3 will definitely set up a 1st Gen AirPort Express.
Is this what you have?

Airport Express (and Airport Extreme) shuts down every now and then

So here's the deal,
I'm using an Airport Extreme as my base station (internet, printer, external hardrive). I'm also using an airport express (for airtunes) that is set up to join my existing network that I have created with my Airport Extreme.
Every now and then, the Airport express disconnects becomes non responding and starts to flash yellow. The strange thing is that even though my Airport Extreme is still showing a green light - this does not work either.
To resolve this I must unplug both Airports, restart Airport Extreme and then make my network. After that I can restart my Airport Express and join my existing network and everything works well for a day or 2 and then the same happens again.
What is going on? I mean even though I have found a solution it is timeconsuming and not very elegent. I would rather not have disconnections:-)
Look forward to hearing from you bright guys!
Message was edited by: Skibsted

Skibsted wrote:
I don't think I have a power issue since I have a lot of electronic connected to the same plug and they are working fine.
I have not tried to use the Airport Express alone but I have of course thought about doing that to narrow down the problem.
I don't have inteference.
How do I check if my neighbours are using the same channel?
There are a couple of programs out there. The one I have used is called iStumbler. http://www.macupdate.com/info.php/id/11753. This will show the networks around you and the channels they are using along with other things.
The distance from the AEX to my Airport Express is like 10 inches!
Having an access point close real close to a client will cause some interference itself. Also you had mentioned you had the AEX plugged into the same stip or outlet with other equipment. This can also cause interference and issues.
The firmware is the latest.
I can say that I think I have found a solution though. When I install my Airport Express I hit the "use to extend my network" instead of hitting "join existing wireless network".
It had been working flawlessly ever since (4 days)
I think extending a wireless network is only used if you have 2 AEBS or more. You would use WDS to extend the range when using an AEX but since you are not using it for that you set it right by joining a network.
Thanks

HT4259 i connected two airport extremes by extending a wifi network. wifi seems weak...help

i connected two airport extremes by extending a wifi network. all my lights are green, and airport utility confirms connections are excellent. but the extended base station hasn't improved my wifi range in the area i set it up in.

If you have a Mac laptop handy, run the test that I have outlined below to find out if the remote AirPort Extreme is really extending the signal at all.
Here, I assume that both of your AirPort Extremes are the newer "square" versions....not the older "round" version.
Locate your Mac laptop close to the "main" AirPort Extreme
Hold down the option key on the Mac while you click on the fan shaped AirPort icon at the top of the screen
Look for the BSSID and jot down the last few characters
The BSSID is the AirPort ID of the AirPort Extreme
Now, move the laptop close the "remote" AirPort Extreme and perform the same test
If you see the same BSSID as the "main" AirPort Extreme, your Mac is picking up from the main AirPort...and the remote AirPort is not configured correctly to extend.
If you see a different BSSID near the remote AirPort, that indicates that the Mac is picking up a signal from the remote AirPort....which is exending the signal correctly.

Disk utility "You can't use this version of the application Disk Utility with this version of Mac OSX. You have Disk Utility 12.1"

I use mountain lion 10.8.1
I try start disk utility it only says: "You can't use this version of the application Disk Utility with this version of Mac OSX. You have Disk Utility 12.1"

To do a Reinstall of the OS boot to the Recovery HD, Command+r key at startup, then select Reinstall Mac OS X. the files will be downloaded from the internet and then the instal will begin.
With Mt Lion it is also available from the Mac App store in your Purchases area. You may be able to download it and then nmanually starting the install while booted to Mt Lion.
But I'd normally use the Recovery HD as that takes the installed OS out of the picture.

Since latest update to airport extreme im getting 10 unknown base station and time capsule items showing in airport utility as a network. when able to "forget" them they initially drop off but soon return. how do i get them deleted and stay that way

since latest update to airport extreme im getting 10 unknown base stations and time caps showing up as though they are a part of my network. sometimes i can "forget" them and they will disappear initially but soon return. i need and want only my connection inside my home . any ideas. i have done a factory reset and set up a new network but they continue to show up.

I'm not convinced that the problem lies in Airport Utility. This same thing was happening to me, nearly exactly as you describe it. The thing is that with me, the problems clearly started when I updated the firmware in my Airport Express (n). That's when all the wacky stuff started happening. Sometimes it would show up in AU, sometimes it didn't and even if it didn't, I could still access the internet through it.
But as you said, the problems got really bad when another Express (b/g) was put on the network with it. Even when it did work, the (b/g) would make it impossibly slow.
You know more about this than me, and clearly have more patience if you've restarted the network fifty times. I gave up at about ten.
In any case, your solution is more of a work around and if you're still having that slow connection problem, I'm not sure you've got it. But thanks for your reporting of this. At least I know I'm not crazy.

Airport Utility can't see the airport, nor are shares visible (Why is there no very extensive 'cookbook' on troubleshooting Airport Extremes?)

For quite a while my MBP (10.5.8) cannot see the Airport Extreme 802.11n (AE) (2nd ed) anymore when I start Airport Utility (AU) (v5.5.3). My solution was to lower security settings of the MBP to 'accept all incoming connections', knowing that this was not a nice solution. Normally I had selected 'acces for specific services and programs' (the lowest option - my AE differs in language). In the past I denied access for requests that regularly came from mDNSresponder (etc), as I could not easily find out how necessary they were. I am not sure whether Bonjour is running; I try to stick to TCP/IP (without Netbios); the same might be the case with other obscure network services...
Then I added another network drive (WD Mybooklive) that works based on shares. The installation program worked fine, I was able to set up the drive for Timemachine backups and -in the proces of upgrading to Snow leopard (I always stay one OS version behind)- my MP3 collection could be read from another drive that was connected to the AE.
I am not sure what exactly lead to the loss, but now I can not see the shares anymore in the finder. Unless I select 'connect to server' (Cmd-K) and fill in afp://ip-adres. I had some trouble with the MBP-drive and Disk Utily could not fix it in multi-user mode. Applejack-auto in single user mode finished after some repairs (catalog file and catalog hierarchy errors), but I doubt that causes the trouble.
In all cases, internetting and accessing the connected drive was no problem.
The funny thing is, my Mac Mini (10.5.8) however can see the AE with Airport Utility (different version) fine. Somehow I get the idea that the networkstack of my MBP has been messed up, but I don't know what it should be, nor how I could check it, or how to repair the stack. But maybe it is not the stack at all.
Right now, I've just reset the AE by holding the reset button for about 10 s. The name has returned to 'Base Station xx', which is visible in AU, but when I click on another button ('manual configuration' or 'continue'), first the message "Are you sure you want to connect to another wireless network?". Finally no connection appears and the error 'AU cannot find your Airport' shows up (while the Base Station is visible in the left column) - or does not show up when I refuse to switch to another network.
So, who can help me to reconnect to the Airport Extreme and/or repair the network stack?

WDS is a difficult setup for many users because it is so easy to make a mistake (while swearing that you are not).
Apple's instructions for WDS are here:
http://support.apple.com/kb/HT4262
I still think the instructions provided by Tesserax are the best available:
http://discussions.apple.com/thread.jspa?threadID=2422028&tstart=0
I can't add any more to this other than to say that long ago when I used WDS, I would swear that I had all the MAC addresses entered correctly, etc and would still have problems. So, I ask my wife to watch me and she immediately catches something like I entered a "l" (letter L) instead of a number "1", or a "O" (letter O) instead of a "0" (number zero).
Finally, there's always the possibility of device that is not holding settings...a defective device.
Hopefully, Tesserax will have some additional thoughts.

My Mac can't find airport express in AirPort Utility - I'm stuck!

I've been fiddling around with this thing for three hours and can't get it to work. I only want to use my airport express to wirelessly play music from my laptop to my speakers on my desk. I dot not want it affiliated with the internet in any way.
I plugged my speakers in to the white square apple thing, then plugged it into the wall. The next step is to open Airport Utility to set it up. My airport utility can not find any devices. It says "AirPort Utility was unable to find and Apple wireless devices. Please make sure the Apple wireless device you want to set up is plugged in and in range of your computer, and then click rescan to try again."
I've checked everything. I am currently about four feet away from the white AirPort plug-in thing, so distance is not it. I'm sure my airport can view all available networks, my AirPort is working fine for my internet (the internet is not affiliated with AirPort Express).
I think maybe this is defective? All help I can find starts off saying to open AirPort Utility, select the new device and, ....
I am running on Mac OS X Version 10.4.11, and I am sure my AirPort device is up to date.
Help?

Yes, I told it to allow wireless networks. It's having a hard time joining my internet network - is that the one I'm supposed to be telling it to join?
I don't want to hook this up to my internet becuase the internet is the other room and I don't watn to mess with the internet settings my Windows roommate already has. I want the speakers to play in the bedroom, which is a good 30 feet away from the living room where the internet base is.
Should i create a new network and ask it to join in on that? but if i do that, will I still get internet?
As it stands right now my airport turns off when i unplug the ethernet, and nothing can be found - even though I told it to enable wireless.
This is so **** confusing. It does seem to work fine when the ethernet thing is in it though... but if I'm going to plug the ethernet chord to it, I'd rather get a long speaker chord and plug my speakers in to my laptop from across the room and save myself the $100 for this airport thign.

HT4259 Why won't AirPort Utility let me extend my network with AirPort Express?

I have 2 1st Gen AirPort Express stations. I have my original AirPort wired into my modem with an ethernet cable and it works fine. I have my new AirPort plugged, well within range of the network but it doesn't show up in AirPort Utility making it impossible for me to extend the network.
All of the previous forums I've seen say to reset both routers and "set up manually" and select the box that says "allow this network to be extended". When I go to setup there is no option for either of these.
Am I missing something? What am I doing wrong?

All of the previous forums I've seen say to reset both routers and "set up manually" and select the box that says "allow this network to be extended". When I go to setup there is no option for either of these.
You are looking at instructions that apply to Snow Leopard and earlier operating sysems. You are using Lion or Mountain Lion.
Hold in the reset button on the Express that you want to use to extend for 9-10 seconds and release.
Close AirPort Utility if if it open.
As edex67 notes above, click the fan shaped AirPort icon at the top of the screen and look for a listing of New AirPort Base Station. Just below that, click directly on AirPort Express.
AirPort Setup will open automatically and take a minute to analyze the network, then tell you that the Express will be configured to "extend" the network.
Enter a device name that you want to use for the Express and click Next
AirPort Setup will take a minute to configure things. When you see the message of Setup Complete, click Done.
You are done, other than locating the Express approximately half way between your "main" Express and the area that needs more wireless coverage.

AirPort Express and AirPort Utility Problems

Hi all
As I have posted before I was having some problems with a slow internet connection and pages loading verrrrrrry slooowly in Safari. Used sppedtest.net to test my connection speed and was finding my upload and download speeds to be fine, so I think that it something other than my DSL intenet connection. Also found that I mgiht be having some problems connecting to the internet via my AirPort Express (sometimes I would see a flashing amber light). After searching Google I found out that I should use the AirPort Ulitity to fix the probem. Well in any event yesterday I updated the firmware on the AirPort, but today was still having some problems. No flashing lights today, but just a slow connection that I do not get on a neighbor's network. Today again I opened the AirPort Utility, but get the following message, "No configured base stations have been found. AirPort Utility will continue to searching." My step-dad suggested taking it to local authorized store/service center to see if they could fix it. Only thing is that they will charge me more the cost of a new AirPort Exprees ($99). Also wondering if I were to buy a new AirPort what is the difference between the Express and Extreme. Not sure if this matters, but my step-dad's computer is a 1.83 GHz Intel Core 2 Duo Mac Mini, while I am on a the newest MacPro. For some reasaon I thought I read were the Extreem might be a better choice, as his airport card runs a a slower speed than mine and the Extremw would allow us each to connect at the different speeds, while the Express would not.
One any help in fixxing my problems and answering my questions is greatly appriecated.
Michael

How old is your Airport Express?
This is your main and only wireless base station?
The new Extremem models do have Simultaneous Dual Band frequencies which allows the faster computers to connect to it with less outside interferrence from 2.4 MHz devices.
These units also have a built-in 3 port hub if needed for other devices like printers and computers that don't have wireless.
http://store.apple.com/us/product/MD031LL/A/AirPort-Extreme?fnode=MTY1NDA0Mg
If you have an old express, it may be worth updating at least to a new model or an Airport Extreme.
Entirely up to you.

I don't know much about computers, so please be patient. I started using Airport and I recently noticed a "network" option right below "Macintosh HD". When I click on "network" it shows "b67446000000" with a computer monitor icon and "connection fail

I don't know much about computers, so please be patient. I started using Airport and I recently noticed a "network" option right below "Macintosh HD". When I click on "network" it shows "b67446000000" with a computer monitor icon and "connection failed". When I right click on this and select "Get more info" it displays nothing, just the spinning wheel. When I select "Connect As" it asked for my password to connect to "Server b67446000000". This may have been on my computer since I got it, I never paid much attention. Is this part of the operating system or has someone hijacked my computer? Why would I need a server...it's just me and my one computer? Maybe someone has hacked in through Airport? Any help will be greatly appreciated. Thanks!

Is your airport a Time Capsule.. if so it is able to serve files on the network.
The number is the MAC address of the network in the router.
Please reset the apple router whatever is and redo the setup.. this time give it a simple name.. eg TCgenX where X is the actual gen of the unit and give it a simple wireless name.. TCwifi and a simple password with 8-20 characters mix of upper and lower case and numbers.
Perhaps even better give me a screenshot from the computer of the airport utility showing me the Airport with its MAC address.

Can't see Airport Express from Airport Utility anymore

I unplugged my airport express when I went out of town for a week. Now that I'm back, I plug in the airport express and it just blinks amber. In Airport Utility I cannot see any networks. Other notes:
- I'm running XP, using the Airport Express with Airtunes to run my stereo
- when I 'View Wireless Networks' I see both the airport express and my neighbor's Apple base station (so it's odd that they don't show up in Airport Utility
- I have tried resetting Airport Express several times, along with my wireless router, cable modem, and computer
- I have checked to make sure software is up-to-date, and even re-installed the Airport Utility.
- I recently purchased an iPhone, and before I left town it worked (with the Remote app and updated iTunes) with the stereo via the Airport Express
- Both the computer and iPhone see my home network just fine, but Airport Utility sees nothing, despite rescanning
- It is possible that either iTunes and/or Windows may have updated since this last worked a week ago.
- I started debugging this three days ago with no progress (it is not intermittent)
Any advice?

I still had phone support, and they showed me how to fix this.
The piece that I was missing is that after I reset the AX, I have to connect to it directly through the wireless connection (dropping to connection from my PC to my home wireless network). From this connection, I can see the AX in Airport Utility and change the settings.
One other piece of info, I was using a manual setup on the AX. This was necessary due to the 26 character WEP password (not using WPA2).

Cannot See Airport Express in Airport Utility

I've been browsing the other topics, but don't see one with my exact problems.
I got an Airport Express for Christmas and was able to get it to work on my parents network; but now that I'm at home, I can't get it to even show in the Airport Utility. I've reset the AX by holding down the button for over a second. I've set my Airport Extreme to be extendable and to be n/g compatible.
I've seen advice like making the name and pass match the base station, but I can't even get to a point where I can see it...
Advice?
Thanks,
Chris

I had similar problems and was able to resolve my issue like Simon. I think you need to hard reset your Airport Extreme base station first, then open Airport Utility and reconfigure it using WAP2 encryption. Then hard reset your Airport Express (by the way, you need to unplug it, push the reset button using a paper clip and keep holding it down while plugging it back and wait until it flashes green 4 times, then release) then you should be able to see your airport express in Airport Utility, and reconfigure it to use WAP2 (I used the same password for both base stations) and, at least in my case, voila! all lights turned green and worked. Good Luck,
Ron

Download Airport Utility 5.6 Instatllation failure

I have to use Airport utility 5.6 to configure my base station,when I download 5.6 and try to install it I get:Installation failed The Installer encountered and error that caused the installation to fail Contact software manufacturer for assistance. I am using Lion 10.7.5 with airport utility 6 .3.1 already installed Any ideas have tried several time to re download with no success

There are plenty of methods of installing 5.6 utility but you must manually do it... here is my method.
How to load 5.6 into later Lion & ML
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.

Unable to find Airport Express in Airport Utility

I am using an Airport Extreme hooked up to a cable modem an Ethernet Printer and a Dell PC. Wireless I have a MAC with the most current OS and a HP Laptop. Everything has worked great for months.
I am trying to add an Airport Express to hook to my TIVO and cannot seem to have it recognized in the Airport Utility. I have done every reset on the AX, but it only flashes yellow and I cannot see it on the left side of my Airport Utility. I am not very tech literate, so I might be overlooking something simple, but I do not think it shoudl be this difficult.

I am not familiar with setting it up with your TIVO, but it sounds like you are having trouble with having your Express join your network. You configure the Express via AirPort Utility. If you cannot see the Express when you open the AU app, click on the AirPort icon (of your Mac) on the upper menu. See if the Express network shows up there. If so, log into that network and open AU again to configure it. If that does not work, get an ethernet cable and connect the Express to your computer. If the Express still does not show up on AU, do a hard reset and try again. Once in AU, you can configure it to try and join or extend your network.

Don't dowload airport utility 6.0 if your network is using old tethered airport expresses. Download Airport Utility 5.6 instead

Similar Messages

Maybe you are looking for