Don't know how to set up iCloud for Windows 7.
I am running Windows 7, and i looked in the Network & Internet section of the Control Panel for iCloud, but iCloud is not there. What do I do?
Did you download it? If so, just run the exe file and after installation it should go directly to the configuration / setup
Similar Messages
-
Don't know how to set current limit for servomotor​s in MID
My application is to control a servo motor. I�m using PXI-7350, driving a motor (Pittman GM8712F434) with MID-7654. The motor is connected to mechanic parts and mechanic parts are connected to a potentiometer as a feedback. Now, according to the spec of the motor, it said reference voltage 19.1V, inductance 5.4 mH, peak current 1.76 A. So, I set dip switch of MID to 0.85 A for continuous current, 1.70 A for peak current and standard inductance. The motor didn�t move and fault LED lighted. Then I set both continuous and peak current to around 1.7A. The motor still didn�t move and fault LED still lighted. I kept increasing the current until the current hit 3A. It started moving slowly but fault LED still lighted. Final
ly I set the peak current to 3.5A, the motor ran normally. Come to the questions.
1. Is the peak current in the spec same as peak current limit in MID? How to determine peak current limit? Because I�m afraid that my little motor is going to burn out.
2. How to set the continuous current; is it suppose to be half of peak current?
3. If +10/-10V command voltage(torque limit) gets map to peak current (let say 1.7 A), will +5/-5V be mapped to 0.85? And what happen after 2.7 sec if I set continuous current to 0.85A? Will +5/-5V be mapped to half of 0.85?
4. How does �2.7 sec� thing works? When I set peak and continuous current to 3.5A and 1.7A, after 2.7 sec motor should run slower or even stop (in my case), but it went nut like it ran at maximum current.
I set Kp 20 and others zero, everything else is same as default. Thank you, I appreciate your answer.infoiupui,
There are several DIP switches on the front of the MID 7654 that can be toggled to vary the continuous and peak current values for the MID. There is a small panel that can be removed from the lower left corner of the MID. You can look in the manual for the 7654, linked below, to determine the particular settings that you should use to achieve given continuous and peak current values.
MID-7654/7652 Servo Power Motor Drive User Guide
http://digital.ni.com/manuals.nsf/webAdvsearch/E382785B7D67553E86256A5D0072BBE1?OpenDocument&vid=niwc&node=132100_US
Take a look at pages 10 through 13 of this document for information on how to modify those DIP switches to achieve current values that will work with the motor that you are using.
I am not clear on w
hat you are referring to when you referred to 2.7 seconds. Could you clarify that for me?
I hope that helps! Let me know if you have any additional questions on this issue.
Regards,
Scott R.
Applications Engineer
National Instruments -
I don't know how to set up a iChat account!
Well.. I don't know how to set up an account on my MacBook ?
I am confused about these fields:
Description, username and password.
Should account should I use? I don't understand all these computer language like AOL and stuff.. I've tried to use my hotmail acc but that didn't worked.Hi,
iChat is a Messaging app that can join AIM or Jabber services up to iChat 5
At iChat 6 and Messages (in Mountain Lion ) you can also use an Yahoo ID.
Apple IDs ending in @mac.com and @me.com and @icloud.com are also Valid AIM Screen Names.
However the @me.com an @icloud.com ones will only work in iChat 6 and Messages (Apple changed the way those version allow AIM to Access the Password to the exclusion of earlier versions)
AIM is based an a central server where all names are registered or kept.
Jabber works on many Jabber servers that are then interlinked.
This allows both Public and Private servers.
Public ones are where anyone can register a Name/ID with the sever.
Private ones tend to be that can only be joined if your belong to the required group of people such as a work/office set up.
Both Google and Facebook run Jabber servers that then allow people to use their IDs with Google or Facebook.
The Boxes in your Picture do various things
The Description adds a Title to the Buddy List
The Username is the Screen Name form AIM or the Jabber ID you are using.
The Password is the one you used when your registered the Screen Name or ID
Titled Buddy list
So, you need either Name that works with AIM or a ID that works with Jabber.
10:12 PM Wednesday; December 5, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.2)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images." No, Seriously -
I am new to Apple and just bought an ipad air. I have a Telus email acct and don't know how to set up a group. Can anyone help me? Thanks
There isn't anything in contacts that has "create a group" . That's why this is so frustrating. I've tried creating a new contact and dragging names into it - doesn't work. I can't find anything that helps!!! What am I missing?
-
Hi. I just bought new Ipad Mini. I don't have network to connect to. Its my first owning one i don't know how to set it up. Help...
FYI
Complete guide to using iOS 6
http://howto.cnet.com/ios-6-complete-guide/
Guide to Built-In Apps on iOS
https://sites.google.com/site/appleclubfhs/support/advice-and-articles/guide-to- built-in-apps-ios
You can download a complete iOS 5 iPad User Guide and iOS 6 iPad User Guide here: http://support.apple.com/manuals/ipad/
Also, Good Instructions http://www.tcgeeks.com/how-to-use-ipad-2/
Apple - iPad - Guided Tours
http://www.apple.com/ipad/videos/
Apple iPad Guided Tours - Watch the videos see all the amazing iPad apps in action. Learn how to use FaceTime, Mail, Safari, Videos, Maps, iBooks, App Store, and more.
http://www.youtube.com/watch?v=YT2bD0-OqBM
http://www.youtube.com/watch?v=ROY4tLyNlsg&feature=relmfu
http://www.youtube.com/watch?v=QSPXXhmwYf4&feature=relmfu
How to - Articles & User Guides & Tutorials
http://www.iphone-mac.com/index.php/Index/howto/id/4/type/select
iPad How-Tos http://ipod.about.com/lr/ipad_how-tos/903396/1/
You can download this guide to your iPad.
iPad User Guide for iOS 5
http://itunes.apple.com/us/book/ipad-user-guide-for-ios-5/id470308101?mt=11
Cheers, Tom -
iMac at work, iMac at home. (Latest Yosemite and Apple Remote Desktop updates installed) Need to work from home at night. I don't know how to set my permissions so that I can just control my iMac at work.
If they have set up port forwarding for you already then that is different. In that case, then you could be experiencing the bug with the most recent release of ARD (3.7.2) and in particular ARD 3.7.2 and Yosemite ARD version 3.8 clients. It has been reported numerous times in the forums and to Apple that since 3.7.2, clients are frequently unavailable to connect to despite there being no network issue between the remote computer and client computer. I have not seen anyone report it who was working from outside the LAN to inside the LAN, but I have the same issue with a number of my own computers that are simply on a different subnet, so it stands rot reason that it would happen from a port forwarding location.
I am sometimes able to resolve the issue locally by SSH connecting into the client computer using Terminal on my admin machine and restarting or relaunching the ARD agent on the remote device, then trying to connect to it again after about 30 seconds.
The Terminal commands for this procedure are as follows, though you might need to include a port number from outside the LAN:
First:
ssh ipaddress -l adminusername
(example: ssh 192.168.1.1 -l macadmin)
Second:
sudo /System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Resources/k ickstart -restart -agent
After that, waiting about 30 seconds and trying to observe or control usually works, though the computer may still fail to show an online or lit-up status indicator. -
HT201699 I don't have an APN in my mini ipad, and I don't know how to set a personal hotspot
I don't have an APN in my mini ipad, and I don't know how to set a personal hotspot
Non Retina display, first gen. iPad Minis DO NOT have personal hotspot feature. This feature started with Retina Display iPad Minis.
-
how do I set up my iPhone5 voice mail? I haven't set up a password, yet it tells me my password is incorrect. I don't know how to set up a password.
I purchased the phone in a retail store a few days ago. Am trying to avoid making an appointment and going back. The purchase took 3 hours.Have you got Settings > General > Restrictions > In-App Purchases set 'off' - that should stop all in-app purchases. And what have you got 'Require Password' set to on the Restrictions screen (I can't remember what version of iOS that setting came in with, so you may not have it) ?
-
If someone phones my mobile number, they are prompted to leave a 10-second message which them comes to me as a text. I want real voicemail with real voices but I don't know how to set it up on my iPhone4S. Can someone help please?
Ask your wireless provider. None of what you describe has to do with the phone itself.
-
Since updating to iOS6, im on giff gaff and I don't know how to set up the VPN to get 3G to work?
oh sorry, well since i have updated to iOS6 i turn on my 3G, then try to connect to the internet with 3G and it says ''Could not activate mobile data network'' then underneath that says ''You are not subscribed to a mobile data service'' would you be able to help?
-
I just upgraded to garageband 10.0.2 and I don't know how to set up a mic for recording via USB
Connect your USB mic or USB Audio Interface to an USB port.
Create an new Audio Track from the Tracks menu > New Track.
Select "Audio > Record using a microphone ...."
Click "Details" to reveal the Input sources.
Click "My instrument is connected with..." to open the GarageBand Preferences "Audio" tab and select your microphone as Input device.
In the Track menu > Track Header enable "Show Record enable" button.
Enable this button for your vocal track.
Open the Library pane to select a vocal patch your new track. -
Question
I don't know how to set up closingFirefox to have all open tabs next time when I open it, without calling RESTORE PREVIOUS SESSIONTools > Options > General
:At the top '''When Firefox starts:''' Show my windows and tabs from last time
You can still bring up your home page later. -
I have a HP BUSINESS INJET PRINTER 2800. I NEED TO KNOW HOW TO SET IT UP FOR MULTIPLE COPIES.
The HP Deskjet 3050 does appear as AirPrint compatible. See this article:
AirPrint basics
Do you have an iPad (your post says iPhone)?
Are you running the latest iOS?
Is your printer up to date firmware-wise? -
HT5312 I don't know how to change my questions for my Apple ID
I don't know how to change my questions for my Apple ID
Alternatives for Help Resetting Security Questions and Rescue Mail
1. Apple ID- All about Apple ID security questions.
2. Rescue email address and how to reset Apple ID security questions
3. Apple ID- Contacting Apple for help with Apple ID account security.
4. Fill out and submit this form. Select the topic, Account Security.
5. Call Apple Customer Service: Contacting Apple for support in your
country and ask to speak to Account Security.
How to Manage your Apple ID: Manage My Apple ID -
Don't know how to configure wireless card for internet
hi i just move to a new place, and i do not know how to set up my mac for wireless connection. i was given the basic information for the internet to work, and it works for my pc but not on mac. i was given
Network Name (ESS-ID or SSID)
WEP Key Type (Encryption type)
WEP Key Format
WEP Key
where do i go to fill in these info for internet?
please teach me what i m missing for i m not familiar with network. thank u.Airport is what Apple's trade name is for 802.11 wireless. If you have wireless in the computer, you have Airport. To see if you have Airport, on your menu bar, go under the and choose "About This Mac." Click on "More Info." About midway down the list on the left, you'll see "Airport." Click on it. That will tell you whether you are wireless-capable or not.
If you do not have Airport, you will need to tether up to the router directly using an ethernet cable if you want internet access or else upgrade the computer with an Airport Extreme card.
If you do have Airport, on your menu bar, go under the and choose System Preferences > Network >Show: > Airport>. Click on Network. If "locked," click on the padlock (lower left corner) to authenticate. Once authenticated, click on Show: and choose Airport. Click on Advanced (lower right corner). Click on "+" below "Preferred Networks" window. Answer the questions that you are asked, which will cover those four items (SSID and WEP info).
(Texas Mac Man: that link points to a guide for the Airport Express stand-alone wireless access point using /Applications/Utilities/Airport Utility, not for how to configure your Mac's built-in Airport Extreme card via System Preferences > Network. I could be wrong but I think annie.ryu is wanting information to configure the computer's Airport/Airport Extreme card via Sys Prefs' Network panel)
Maybe you are looking for
-
Hello, I ran a new install of Team Foundation Server and let it install the built in SharePoint pieces on a single server setup. After the install i'm able to access the http://teamfoundation:8080/tfs/ address without issue but am unable to create a
-
Unable to start the operating system on my MacBook Pro
Suddenly today my MacBook Pro isn't starting and showing a folder with a question mark sign blinking in it and I am unable to access the software and the hard drive . How to recover the hard drive without loosing my data also I have tried holding the
-
My child deleted te camera icon and I can't get it bck! I've tried reset and hard reset but it's not working!
-
Different Depr Areas for different Company Code
Hi Gurus, We have the followings: i We have 1 Chart of Depr ii Company Codes A & B (common ChoA) iii Depreciation Areas: 1, 2 and 3 Each Depr Area has its own accounts in AO90. I check the "Depr Area block" indicator, say for area 3, when I do AS0
-
For some reason my animations started acting up, every time I Ctrl+V'd it pasted it over all layers,unlike before and It will not show the change in images if I hide some until I move the image in the layer , how do I fix it?