DONE does not go HIGH on spartan6 but ghigh is 1 and crc error is 0
hi all,
I use the USB platform cable to configurate the Spartan6 FPGA from the JTAG,but the done does not go high.
I had a 330Ω pull up on done pin
a 4.7K pull up on program_b
a 4.7K pull up on init_b
please help me
Thanks!
INFO:iMPACT - Current time: 2015-7-19 14:57:23
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': Programming device...
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
'1': Reading status register contents...
[0] CRC ERROR : 0
[1] IDCODE ERROR : 0
[2] DCM LOCK STATUS : 1
[3] GTS_CFG_B STATUS : 0
[4] GWE STATUS : 0
[5] GHIGH STATUS : 1
[6] DECRYPTION ERROR : 0
[7] DECRYPTOR ENABLE : 0
[8] HSWAPEN PIN : 1
[9] MODE PIN M[0] : 1
[10] MODE PIN M[1] : 0
[11] RESERVED : 0
[12] INIT_B PIN : 1
[13] DONE PIN : 0
[14] SUSPEND STATUS : 0
[15] FALLBACK STATUS : 0
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0010 0100 1100 1000
INFO:iMPACT:579 - '1': Completed downloading bit file to device.
INFO:iMPACT:188 - '1': Programming completed successfully.
LCK_cycle = NoWait.
LCK cycle: NoWait
INFO:iMPACT - '1': Checking done pin....done.
'1': Programmed successfully.
PROGRESS_END - End Operation.
Elapsed time = 3 sec.
tiboy wrote:
Thanks!
The fpga done pin also connectied on a pin of MCU which is Low during not program.
So When MCU initialized and Hi-Z the done pin
The fpga configuration is still time to success?
If I understand you, the MCU drives the DONE signal low when you first power-on the system, but should release the pin (go hi-Z) when it has finished its own startup initialization? It is OK for the DONE pin to be pulled low by an external source. That is one way to prevent the FPGA from starting up until other board circuitry is ready. However once the external device is no longer driving low, the DONE signal should go high. I would double-check your MCU software to be sure you are not still driving the signal low after initialization. If possible, try to disconnect the MCU from the circuit to see if DONE goes high.
Similar Messages
-
Hi
How can I hook up my DVI Adapter onto my new MacBookAir if the machine does not have a mini port (but only 2 USBs and 1 Thunderbolt)?
Is there a DVI adaptor already for Thunderbolt?
Thanks,
JFRThe Mini Display port and Thunderbolt port use compatible connector bodies. Your current Mini Display to DVI or VGA adapter will still work as before on the newer Thunderbolt capable machines.
-
I have had my iMac for 55 days now and twice I had to power off/on and then It does not power up correctly. I verified my disk and found errors that could not be repaired (errors were associated with boot drive) I erased the drive and restored system back to the previous day. Has anyone else experienced this problem?
Since it's a new machine, contact Apple's Support and let them deal with it. Allen's already recommended an Apple repair station visit. Do note that if you have AppleCare's protection plan and you're within 50 miles (80 KM) of an Apple repair station, you might be eligible for an onsite repair since yours is a desktop machine (depends on where you're located). BTW, the AppleCare Protection Plan's the best warranty policy available for desktop machines. Get it if you don't have it before contacting Apple.
27" i7 iMac (Mid 2011) refurb, OS X Mavericks (10.9.4), ML & SL, G4 450 MP w/Leopard, 9.2.2 -
Mom does not see my iChat video, but I see her, and my wife can see mine
When I iChat with Mom, I can see her, but she cannot see my iChat video. All she sees is herself as if she is still in iChat preview mode. Audio works fine. It is like a 1-way video chat with a 2-way audio chat, only we did not request this mode.
This was working for years (from when Mac OS X Panther first offered iChat video chats). Mom only seeing herself is a fairly new situation, but I can not pin down when it started, or what might have triggered it.
My wife can connect with my Mom, and again, my Mom's display stays in preview mode, but my wife can see my Mom, same as I see, only my wife is using her own MacBook Pro.
When I'm at Mom's using my MacBook, I can iChat with my wife. She can see me and I can see her. My wife and I can also successfully iChat video chat when she is away on business trips using the hotel's WiFi. I do not think it is my MacBook, nor my wife's MacBook Pro.
And also while at Mom's with my laptop right next to Mom's iMac G4 using a Bonjour local connection, I see what Mom is sending, but she stays in preview mode only seeing herself.
So I think I've eliminated the internet as a whole, and I've eliminated my MacBook as being the cause.
I really think it is Mom's iMac G4.
I've tried trashing all the iChat related .plist files, but I could have missed something.
Mom's Connection Doctor says it is getting stuff from me at between 13 and 15 frames/second, but all that is shown is her own iSight image.
Some configuration details:
o Mom's 1.25GHz G4 PowerPC iMac is Mac OS X Tiger (10.4.11) all the latest updates.
o Mom uses the original firewire iSight.
o While I think I've eliminated the router, it is an 802.11n Airport Extreme (single transmitter in 802.11b/g/n 2.4GHz mode, channel 1).
o Verizon DSL connection that has worked just fine in the past, beside same situation occurs when I'm sitting next to Mom using a Bonjour connection.
o Mom is 300 miles away, so I can not just drop in. However, I do have VNC access to Mom's system over an ssh tunnel.
o Firewall is Off
o My 2GHz intel Core 2 Duo white MacBook is Mac OS X Leopard (10.5.8) all the latest updates (w/build-in iSight camera).
o My wife has an intel 2.2GHz Core 2 Duo MacBook Pro running Mac OS X Leopard (10.5.8) all the latest updates (w/build-in iSight camera).
o My router is also an 802.11n Airport Extreme (single transmitter in 802.11n 5GHz only mode), with an older flying saucer Airport Extreme 802.11g in bridge mode to support older Macs and iPod Touchs.
o My broadband is also a Verizon DSL connection.
o Firewall is Off.
Events that have happened recently. I'm not saying they are the cause, but generally things that did work do not stop working for no reason at all.
o I've applied Apple's Software Updates.
o I've experimented with TeamViewer.com as an alternative to VNC for remote control (this did not involve video, but it was something new to the mix). NOTE: I DO NOT keep TeamViewer running. I find my VNC via OSXvnc to be satisfactory.
o My nephew moved back in with his Mom (my sister) and his Dad, which is where my Mom happens to live. However, my nephew has his own 12" G4 PowerBook, so he does not need to mess with Mom's. But then again, years ago, I found my Mom's previous Bondi Blue iMac had its web server enabed after a visit from my nephew. Of course now he is a college gradate and much more responsible. Oh yea my nephew was a College Quarterback for a Top Ten College, and I'm a bookworm type. I am not going to accuse my nephew of doing something to his grandmother's iMac unless I have absolute proof
o At one time I had the Chax plug-in installed on Mom's iMac G4. I used Chax to uninstall itself.
I'm stumped. I've tried all the problem isolation things I could think of, as well as the tried and true "Delete the .plist" trick (assuming I found the right .plist(s)).
Has anyone actually lived through this, solve it for someone else, other.I would do the Latest Combo Installer for the OS level she is at.
That is going to have to wait until after Thanksgiving.
While I'm confident that applying/re-applying the latest Combo Update will not cause any problems, if anything goes wrong (and I know Murphy personally), I will not be able to drive the 300 miles to Mom's house until the weekend following the Thanksgiving weekend.
If I'm going to try doing something like this remotely, I'm not going to do it unless I can get in the car and be a Mom's house the next morning to clean up any mess I create.
So I will put your idea in my "To Do" list (I'll even create a Google Calendar event), to try this 4-Dec-2009.
Thank you for the idea. If I have not found a solution before the 4th, I will install the Combo update.
But I do have a question. Why would Mom's iChat display the video preview window showing what her iSight camera sees, if she was unable to display the remote video stream, just because there was a ColorSpace issue. Hay, I write software for a living, so I know that the left hand does not need to know what the right hand is doing, not the big toe, the elbow, an ear, etc... Software is full of paradoxes. But I figured I would just ask.
And I'm still going to give the Combo update a try on 4-Dec-2009.
But in the mean time. Other suggestions would be appreciated.
Does anyone have a laundry list of .plist files I should try deleting? I did try deleting some obvious ones, but maybe I missed something important, or maybe there is one that does not say iChat, but is just as important.
You never know, if I get enough ideas (tons of ideas), and they all still fail, and I'm frustrated beyond belief, maybe I'll break down and get Mom a nice 27" iMac for Christmas! But if I do that, I'm getting one for me first -
Hello，everyone.
I am using virtex6 FPGA and trying to download mcs file to PROM and have failed.
I download .bit file to FPGA and succeed.
When i try to download .mcs file to PROM XCF128X-FTG64C(BPI Flash) and choose Slave SelectMAP Mode
and the process is about 68% it fails.
The message below the IMapct is as belows:
done.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
// *** BATCH CMD : identifyMPM
// *** BATCH CMD : assignFile -p 1 -file "C:/Users/Administrator/Desktop/TEST/LED/led.bit"
'1': Loading file 'C:/Users/Administrator/Desktop/TEST/LED/led.bit' ...
done.
INFO:iMPACT:2257 - Startup Clock has been changed to 'JtagClk' in the bitstream stored in memory,
but the original bitstream file remains unchanged.
UserID read from the bitstream file = 0xFFFFFFFF.
INFO:iMPACT:501 - '1': Added Device xc6vlx240t successfully.
INFO:iMPACT - Current time: 2014/3/13 8:48:14
// *** BATCH CMD : Program -p 1
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading: 2.997 V, Max. Reading: 2.997 V
1: VCCAUX Supply: Current Reading: 2.997 V, Max. Reading: 2.997 V
'1': Programming device...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:579 - '1': Completed downloading bit file to device.
INFO:iMPACT:188 - '1': Programming completed successfully.
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
INFO:iMPACT - '1': Checking done pin....done.
'1': Programmed successfully.
PROGRESS_END - End Operation.
Elapsed time = 23 sec.
Selected part: XCF128X
// *** BATCH CMD : attachflash -position 1 -bpi "XCF128X"
// *** BATCH CMD : assignfiletoattachedflash -position 1 -file "C:/Users/Administrator/Desktop/TEST/LED/leda.mcs"
INFO:iMPACT - Current time: 2014/3/13 8:49:32
// *** BATCH CMD : Program -p 1 -dataWidth 16 -rs1 NONE -rs0 NONE -bpionly -e -v -loadfpga
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading: 2.997 V, Max. Reading: 2.997 V
1: VCCAUX Supply: Current Reading: 2.997 V, Max. Reading: 2.997 V
'1': BPI access core not detected. BPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file D:/Xilinx/14.3/ISE_DS/ISE/virtex6/data/xc6vlx240t_jbpi.cor.
'1': Downloading core...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:2492 - '1': Completed downloading core to device.
Current cable speed is set to 6.000 Mhz.
Cable speed is default to 3Mhz or lower for BPI operations.
Current cable speed is set to 3.000 Mhz.
Setting Flash Control Pins ...
Setting Configuration Register ...
Populating BPI common flash interface ...
Common Flash Interface Information Query completed successfully.
INFO:iMPACT - Common Flash Interface Information from Device:
INFO:iMPACT - Verification string: 51 52 59
INFO:iMPACT - Manufacturer ID: 49
INFO:iMPACT - Vendor ID: 01
INFO:iMPACT - Device Code: 18
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x008CE03B.
done.
'1': Erasure completed successfully.
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
Setting Flash Control Pins ...
'1': Flash Programming completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Reading device contents...
done.
'1': Verification completed.
Setting Flash Control Pins ...
Current cable speed is resumed to 6.000 Mhz.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
`Elapsed time = 814 sec.
and i find many people have met the same thing. But they are spartan series FPGA and i try to low the Resistances of Mode pins,M0 M1 and M2, but the problem does not been solved.
I have read the status Registers and find there is an over-temperature state
and in Impact i could not readback the registers. It is strange.
I am anxious about this problem and have not solved it yet
What reasons may it be?
Hope for your answer, thank youHi~I want to know if you solve the configuration problem for virtex-6?
As I encounter the same configuration problem, I want to consult you with some question.
Can I have your email?
gszakacs wrote:
I have measured the VCCINT and find it is 1.0V, not 2.997V;
That is not at all surprising. I always assumed the problem is with reading the XADC (system monitor) block and not with the voltage or temperature.
my Reference board is ML605
That would have been nice to know at the beginning...
It seems that you have selected the correct mode, assuming your jumpers are set as required in the ML605 Hardware User's Guide. See table 1-27, table 1-33 and the note below it about switch S1.
I'm not that familiar with the details of this reference design, but it may be that the slave SelectMap circuitry requires a reset or power cycle to actually configure the FPGA. Have you tried power-cycling to see if the FPGA boots from the flash?
I'd also suggest that you select the V6 in the JTAG chain view, then go to the debug menu of Impact and select Read Device Status (this is from memory, but it's something like that). That will not only show the bits of the configuration status register, but also describe what each bit means. Among other things you can check the state of the FPGA's configuration logic and the Mode pins.
-
I have seral email accounts on my Mac. One does not work on the Mac but works on my iPad and iPhone. The account information was added on the Mac. I keeps rejecting my password.
You don't input the information in manually for iCloud mail. It is automatically set up for you when you sign into iCloud via System Preferences and choose the Mail checkbox. Sign out of iCloud or deselect Mail in iCloud preferences. Open Mail's preferences and choose accounts tab. If iCloud account still exists in the list, delete it. Sign back into iCloud or check the box for mail. The account will be auto created for you.
-
V5 in BPI Mode " Configuration data download to FPGA was not successful. DONE did not go high,"
Hello，everyone.
I am using virtex5 XC5VLX155 FPGA and trying to download mcs file to BPI flash and have failed.
The flash is JS28F512P30E. The iMpact version is 14.7.
FPGA's VCCINT is 1.0V, VCCAUX is 2.5V. VCCO is 3.3V.
M[2:0] is 010 in Master BPI. Ican program FPGA through JTAG. The FPGA_DONE pin 's LED can always flash.
The error is shown as below. the full IMPACT console log and the SCHEMATIC_ FLASH are in the attachment.
Using x16 mode ...
Setting Flash Control Pins ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x004E4AFF.
done.
'1': Erasure completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
'1': Flash Programming completed successfully.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
PROGRESS_END - End Operation.
Elapsed time = 692 sec.
Hope everyone give more advices. Thank you.
Thank you very much!
I can read ack the mcs file, but the file is much bigger than the original mcs file.
The flash datasheet is in the attachment.
I want to use the Master BPI mode. In BPI_UP, the address starts at 0 and increments by 1 until the DONE pin is
asserted. I do not know the difference between the BPI_UP and BPI_DOWN.
ps: The R61,R62 and R63 are not weld on the board. The ADV pin is tie to VSS .
-
How can I connect my 3gen apple tv with HDMI to my BUSH LCD32TV022HD
This does not have an HDMI port but does have:-
1) S-Video I/P,
2) Video I/P,
3) Audio Input (Left & Right)
4) Audio In jack (for VGA and DVI source)
5) DVI input
6) VGA inputWelcome to the Apple community.
The Apple TV doesn't officially support a DVI connection, however you may be able to get it to work. You will first need to check that your TV supports either 720p or 1080p as well as HDCP. If you are able to get the video working over the DVI connection, you may also require a DAC in order to connect with Apple TV's optical audio output to the TVs audio imput.
You may well wish to make sure that the DVI connection works before spending any money on a DAC.. -
Can someone please help me get my iPhone to sync to your computer?
I can not sync my iPhone to the computer. I keep getting up an error message that synchronization does not want to start. I have uninstalled iTunes and then reinstall it. But the same warning box will appear. How can I get my phone in sync again?Hello lenmin,
Thanks for using Apple Support Communities.
To help resolve this issue where you're repeatedly prompted to authorize with your Apple ID in iTunes when syncing, please follow the directions in the article below.
iTunes: Missing folder or incorrect permissions may prevent authorization - Apple Support
Have a great weekend,
Alex H. -
If I want to sign in to this message board, I can do so. I can also sign in on my iPad to download updates, purchase new apps and songs, etc. And I can sync my iPad to iTunes on my iMac.
But when I open iTunes on my iMac, it asks for my password and I can't sign in. What is causing this problem with iTunes on my iMac repeatedly asking for my password when I open iTunes?
This is very frustrating. I am also worried that I won't be able to sync when my new iPad arrives March 16. Help!The solution (for me at least) is to keep trying the same password in iTunes on my iMac that I know is correct. For me, the fourth try of typing in the exact same password works in iTunes on my iMac. I have repeated this several times, and each time it works.
What is messing people up is that when iTunes does not recognize the correct password, people are attempting other passwords. Those other passwords are all incorrect. The problem, as you stated, is that the password was entered correctly the first time but because of iTunes having issues it does not recognize it.
People, just keep entering the password you know is correct. It will eventually recognize it, or at least this works for me. If this still does not work, reset your password (but then you may still have to enter it repeatedly in iTunes).
Apple needs to fix this. -
Can someone please help me to remove an iphone telephone number from my imessage application. I no longer have a phone which I registered on my apple ID as a second phone. I have been on my apple ID and it does not seem to be there but cannot remove it from imessage, which still has it as an option to connect to. I am concerned that someone else who inherite this old phone will see my messages if I accidentally enable it again. I have read and re-read various postings and tried all options given but no luck, the **** thing stays there.....
Hey Chappers64!
Here is an article that will help you with this issue:
iOS: Deactivating iMessage
http://support.apple.com/kb/ts5185
If you have already tried these steps, you will want to utilize the information at the end of the article:
If you can't deactivate iMessage after you perform the steps above or you can't access the iPhone, please contact Apple Support.
Thanks for coming to the Apple Support Communities!
Cheers,
Braden -
itunes 11.1.3.8 shows a speaker icon in front of the seclection but it is not playing. the progress bar does not move. there are speakers attached to the system and all other programs do profuce an audio output.
Go to the Edit -> Preferences-> Playback
In The bottom section of the page click the drop down menu by Play Audio Using and select Windows Audio Session or something other than "Direct sound" or whatever it displays. Click Okay. This worked for me! I hope it works for you too!
Thanks,
John -
premiere elements 12, new installation, serial no. accepted, installation completed and new started, but does not run. I get following msg-box: "LoadLibrary failed with error 126: Das angegebene Modul wurde nicht gefunden." Installation in German Language on WIN7 professional 64bit, Samsung SSD. What can I do to run that program?
Jurgen Freund
Premiere Elements 12 on Window 7 64 bit. What video card/graphics card does your computer use - AMD Radeon?
I have found this YouTube video on the subject of Error 126 with details for resolving the problem.
How to fix the ERROR 126 when you open OpenGL programs - YouTube
The link was contributed in an old 2013 thread here by the ID danneomarre (see post 6 of the following thread)
LoadLibrary failed with error 126: cant find the required
Please let us know if that worked for you.
Thank you.
ATR
Add On...When all is OK and working, please update 12 to 12.1 Update using an opened project's Help Menu/Update. -
My old 17" MBP (2005) often crashes, freezes or shows grey screen at start up. Also track pad often does not work. I have re fomatted the HD and reinstalled system but to no avail. Genius bar says possible faulty HD, but I suspect logic board. All checks out OK on the Apple Diagnostic bench. Can a Logic board go intermittant?? Any Ideas any body??
Ive repaired 1000s of laptops over the years (translate: diagnose and replace parts).
Its not that old, Ive owned 100s of laptops (most were free) ....some I still have are nearly 13 years old and still perfect, ....some extremely expensive ones died in under a year.
other than becoming obsolete at some point, there isnt really any "will spoil on" data like Milk for solid state computer parts, ....alas.
You can have a $5000 laptop die in 4 months, and a junker one keep kicking after 10 years.... Ive seen that firsthand countless times.
Common logic dictates that "very expensive = long life" in computers,..... but all the repair people will tell you just the opposite.
I know you have a gripe, I get that all too well honestly . -
when I connect my iPod touch to your computer, itunes does not detect it ... but in My computer is detected as an external disk why?
See:
iOS: Device not recognized in iTunes for Windows
IOt is normal and expected for the iPod to appear in My Computer
Maybe you are looking for
-
How to add a column in Item Master form with chooselist
Hi Experts I add a column in Item Master Form in Stock Data Tab. In this column I want to add Choose list. For this I use AfterFormLoad event. It gives Error "Matrix Line Exist" . My code is given below If pVal.FormType = "150" Then f
-
Subform dynamic position in adobe forms
Hello All, I need to place a subform for document totals always at the end of content area. It needs to be after the last printed item and if there is enough space, otherwise jump to the end of next content area (in next page). Anchor option in layo
-
Credit card Open sales order data migration
Hi All, My query for today is to know your experiences as to how to handle legacy data migration to SAP for Open transactions having credit card information. I mean in legacy we have Open orders with credit card information and some of them are appro
-
Non Drop frame capture causing out of sync clip?
Hi, All, I've been having trouble with sync issues on an hour long tape capture. The material was captured from a Canon consumer DV cam (z80) using firewire into my powerbook g4. (The material on the dv tape was originally recorded in Video 8mm and t
-
Powered boxes do not play in stereo
I can't find the name of this computer (There are seceral numbers on the back but none of them is usable) but he is twee years old and it's a desctop computer. Problem: when I use my powered boxes, they pla in mono. This is awfull of course, so does