Door entry system on FXS port of UC320W

Hello,
I have inherited a door access system with no information on it. I have plugged it in to the FXS port on the UC320W and assigned it extension 199. I can dial 199 and press "8" and the door opens, so it is going well.
My problem is I don't know what number the door is auto dialling when you press the call button at the door end. I can hear the tones, so I know it is three digits, but I have no idea what they are. Is there any way to monitor the FXS port to see what number is being dialed when I press the call button?
Cheers,
Tony

This is the log, am I right in thinking it is dialing "5" or "325"?
Jul 5 15:38:42 UC320W user.debug voice: INVITE sip:[email protected]:6060 SIP/2.0
Via: SIP/2.0/UDP 10.1.1.1:5080;branch=z9hG4bK-c3a41e2b
From: "Door" ;tag=15b8fd873df7b9cbo0
To:
Call-ID: xxxxxxxx
CSeq: 101 INVITE
Max-Forwards: 70
Contact: "Door"
Expires: 240
User-Agent: Cisco/UC320W-2.3.2(6)
Allow-Events: talk, hold, conference, x-spa-cti
P-Mailbox: 5199
Content-Length: 325
Allow: ACK, BYE, CANCEL, INFO, INVITE, NOTIFY, OPTIONS, REFER
Supported: x-sipura, replaces
Content-Type: application/sdp
v=0
o=- 2244391 2244391 IN IP4 10.1.1.1
s=-
c=IN IP4 10.1.1.1
t=0 0
m=audio 16476 RTP/AVP 0 2 8 18 100 101
a=rtpmap:0 PCMU/8000
a=rtpmap:2 G726-32/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:18 G729a/8000
a=rtpmap:100 NSE/8000
a=fmtp:100 192-193
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=ptime:30
a=sendrecv
Jul 5 15:38:42 UC320W user.debug voice: SIP/2.0 404 Not Found
To: ;tag=1a27709e-0
From: "Door" ;tag=15b8fd873df7b9cbo0
Call-ID: xxxxxxxxx
CSeq: 101 INVITE
Via: SIP/2.0/UDP 10.1.1.1:5080;branch=z9hG4bK-c3a41e2b
Server: Cisco/UC320W-2.3.2(6)
Allow-Events: talk, hold, conference, x-spa-cti
Content-Length: 0
Jul 5 15:38:42 UC320W user.debug voice: ACK sip:[email protected]:6060 SIP/2.0
Via: SIP/2.0/UDP 10.1.1.1:5080;branch=z9hG4bK-c3a41e2b
From: "Door" ;tag=15b8fd873df7b9cbo0
To: ;tag=1a27709e-0
Call-ID: xxxxxxxx
CSeq: 101 ACK
Max-Forwards: 70
Contact: "Door"
User-Agent: Cisco/UC320W-2.3.2(6)
Allow-Events: talk, hold, conference, x-spa-cti
P-Mailbox: 5199
Content-Length: 0

Similar Messages

Valcom 2001A single zone paging system with a Cisco 2821 FXS port

I am new at troubleshooting the Valcom paging system with Cisco 2821 router. I recently installed a Valcom 2001A that is connecting to FXS port on the Cisco router. The paging works but the ringing does not stop when the page extension is dialed (you can talk over the ringing). I was told to use the Valcom 9970 to work with the FXS port on my router. Will the V9970 worth with the 2001A or in place of it? Is there anything else I need to know to perfect this install? Thank you!

Put the command 'forward-digits extra ,,,,01' on the outgoing POTS dial-peer. Each comma is one second of delay.

No Service for System SAPECC(Sender Port), Client800(R/3 system client 800)

Hi friends,
I am new to XI/PI I am working with IDOC to Flat file scenario I am facing the folllowing error.
No Service for System SAPECC(Sender Port), Client800(R/3 system client 800) in integration Directory.
can any one tell what was the reason for this error.
Thanks in Advance,
Ravi Yasoda.

Hi Ravi,
Have you imported the Business System in Integration Directory?
Check whether you see the logical system name in adapter specific identifiers or not...
Also check from integration directory that cache notification was done and also check SXI_CACHE in the abap stack.
See this thread...
No service for system SAP***, client 001 in Integration Directory
Please go through below content from sap note for your issue...
Error message: No service for system SAPABC client 123 in the integration directory
Solution:
You send IDocs from system ABC to XI. In the control record of the IDoc,the SNDPOR field contains the value "SAPABC". The client of the sending system is determined by the MANDT field of the control record. The system ID and client are then used to determine a service without party of the
type (business-system/business-service):
Business system
-> Activities in the System Landscape Directory (SLD)(Create technical
system):
Create a technical system for system ABC in the SLD, and create the client for this. Do not forget to assign an "ALE logical system" (for example, "ABCCLNT123") to this technical system.
SLD (Business system):
You can now explicitly assign a business system to this client. For more details, refer to the SLD documentation.
Activities in system ABC (self-registration in the SLD):
Alternatively, you can register the system in the SLD in system ABC with Transaction RZ70. You will find detailed information about the SLD registration of systems on the SAP Service Marketplace for the
"Exchange Infrastructure" in the document "Exchange_Installation_Guide.pdf".
In system ABC, you can check your configuration with Transaction SLDCHECK.
Activities in Integration Directory (import business system from SLD):
You will find the business systems under Services Without Party in the Integration Services. In the Service menu, you will find the system identifiers, the client, and the corresponding ALE logical
system under "Objects"->"Adapter-specific identifiers". Use the Import/Update button to copy the data from the SLD, to create business systems, or to update their identifiers.
Business service
-> Activities in the Integration Builder directory:
You want to create a service without party that is not part of your system infrastructure and is therefore not maintained in the SLD. In the Integration Builder directory, you will find the "Business-Services" under Services Without Party. In the Service menu, you will find the system identifiers, the client, and the corresponding ALE logical system under "Objects"->"Adapter-specific
identifiers".
Activate the change list in Integration Directory.
In system ABC, you can restart the incorrect entry from Transaction SM58 .
Regds,
Pinangshuk.

How can I get my passcode protected iPhone6 to work with building entry system?

iPhone6 issue: The apartment building has an entry system that dials my phone so I can remotely release the door. When I have a passcode on the phone it will not ring when the system dials it. Without the passcode it works. How can I keep the passcode on my phone and use the entry system?

Here is a list of products that are not supported in the win7 OS. This product is listed there.
Products not supported in win7
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Transmission Volume on a FXS Port

G'Day,
We have a fax machine connected to an FXS port in a 2851 (CME 4.1). Running tests on the machine reveal that the transmission volume is set too high, causing distortion on faxes and an inability to fax to some destinations.
Is there a way to turn the transmission volume down at the port-level? Apparently it cannot be done on the fax machine (? this sounds odd to me...but the technician for the machine is adament)
Thanks,
-marti-

This depends if the faxing is being done via fax relay or fax passthrough.
If fax relay is being used, the fax traffic originates from the egress voice port connected to the PSTN, not from the FXS port that has the fax machine on it. The output level of the fax relay codec is fixed - at this stage it is not possible to alter the level of the outgoing audio on the 2800/3800 ISR's.
If you use fax passthrough, the audio is transmitted via a G711 codec. You can use the voice port 'input-gain' or 'output-attenuation' command to boost or reduce the levels in different directions.
If the level FROM the CME system towards the PSTN is too high (for example 3dB), you would use the command 'input-gain -3' on the FXS port to reduce the inwards audio level by 3dB, so the level SENT to the PSTN is correspondingly reduced by 3dB.
Most fax machines can set the outgoing audio levels - they may have a special config menu that is not normally directly accessible by users.

Phone in FXS Port in Key mode

I have a system in Key Mode, and cannot seem to figure out how to get an analog phone that's plugged into the FXS Port to make an outgoing call.

Hi Russ,
In pure key system mode the FXS port (and SPA502 phone) can't be configured as a member of a Shared FXO Line. There is no way to directly reach these phones on an inbound call. They can however, be used to make out bound calls if the system is configured in blended mode and the option 'Include in Outbound calls' is checked on the Shared FXO Lines page. In this scenario the FXS phone would dial 9 + address and the system will let the FXS use an idle FXO that has that capability enabled.
Hope this helps.
Chris

Multiple FXS ports on a 3745 to the PSTN

Hi,
I'm putting together a spec to have 35 FXS ports routed directly to the PSTN via an ISDN PRI.
Can anyone foresee any issues with doing this with a 3745, fitted with 3 x NMHDA-4FXS + 3 x EM-HAD-8FXS + appropriate PWDM2 mods + NM-HDV-E1 (or AIM-MFT VWIC?) + appropriate IOS image?
This would be a standalone system (e.g, not controlled by a CallManager), and all the phones will need dedicated lines. And each port will need to be able to generate a line reversal signal.
Any input on this would be appreciated.
Cheers,
J.

You can go through the following document and check whether the current IOS version supports it .
http://www.cisco.com/en/US/products/hw/routers/ps282/products_data_sheet09186a0080091ba1.html

Motion PNG on LCD IP Phone for door entry camera

Hello, I need a cheap solution to display a door entry camera on a Unified Comms series IP phone. I can get a motion .png solution using the services button but the refresh on the display is max 3sec. Is there a model IP phone that can handle a video stream or a faster refresh rate excluding the 7985.
I know in the Linksys range they have a phone with streaming video PHM1200 but I cant find much information about it as to whether it can do SIP etc...
Any advice appreciated.
Thanks

Hi,
I've just spoken with someone that I know from Cisco, and they told me that the SPA series (both Cisco and Linksys) phones using a "COMPLETELY" different operating system environment, which means that they are configured differently (I've heard, and the fact that I have a similar model the SPA942, I can tell you it's a lot easier if you are using SIP.) Also I know for sure that what you are trying to accomplish will not work on ANY of the SPA series phone.
Why?
Because Cisco acquired Linksys which acquired a company called Sipura, who FIRST manufactured the Linksys PAP2 ATA adapter and the SPA series phones, and then it was acquired by Linksys and then later acquired by Cisco. The Cisco 79xx phone were originally manufactured by Cisco, and then after Cisco acquired Sipura, they made some modification to it to make it work better, but still it's based on Sipura...
I know this is very thoroughly, but hope this helps... ;-)

Mail account cannot update because home directory is full. But I can not get into mail without freezing. Is there a back door entry?

mail account cannot update because home directory is full. But I can not get into mail without freezing. Is there a back door entry?

Do you mean that your startup disk is full?

Cisco 2432-24FXS Calls won't ring FXS ports when placed in Huntgroup

Hi,
I am having an issue getting calls to ring through on the FXS ports when using the "trunkgroup" command under the POTS dial-peers. Calls will ring through fine if I use the "port" command under the pots dial-peer. What I am trying to accomplish is getting a single number to hunt through 13 FXS ports in a round-robin fashion. With the below setup I am getting a SIP 404 not found message in the SIP debug info. I am not sure if I am missing something here or what the deal is. If the below information is not enough I would be happy to provide additional info. Any idea's why this configuration doesn't seam to work?
trunk group HuntGroup1
hunt-scheme round-robin both up
dial-peer voice 1 voip
translation-profile outgoing 7to11
destination-pattern .T
progress_ind setup enable 3
no modem passthrough
voice-class codec 1
session protocol sipv2
session target dns:XXXXXXXX
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
no vad
dial-peer voice 300 pots
trunkgroup HuntGroup1
description TEST NUMBER
destination-pattern XXXXXXXXXX
voice-port 2/0
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 1
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/1
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 2
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/2
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 3
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/3
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 4
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/4
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 5
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/5
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 6
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/6
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 7
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/7
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 8
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/8
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 9
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/9
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 10
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/10
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 11
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/11
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 12
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/12
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 13
station-id number XXXXXXXXXX
caller-id enable
Message was edited by: Thomas Schmidt
Added CCSIP Debug and Router Config.

Hi.
Can you please attach the complete config and a debug ccsip message?
Thanks
Regards
Carlo
Sent from Cisco Technical Support iPhone App

CLID not shown on FXS port

I am using Call-manager 6.0.1b, a MGCP controlled Gateway.On the Gateway i have installed a NM-HD-2V with a Vic2-2FXS module. On this module i connect 2 analog phone with capability to display the Caller-ID. When i call the analog port from a ip phone or from the other analog phone the Dn is not shown. When i connect the phone directly to the PSTN and dial this nr via my cell phone the nr is shown so i expect that the nr format received is not correct. How can this performed that the correct format is shown to the FXS port connected phone ?

Hi,
Yes - you are correct. Looked at this one too quickly.
You will want to make sure the CPTONE defined on the port is for the country the phone is manufactured for, and that the voice-pport has the 'caller-id enable' command.
If those are both correct, and I'm guessing that they are since some caller-id works, then you need to inspect the gateways that take the calls to begin with.
Do you have caller-id trouble for internal calls also?
How do these calls come into your network?
hth,
nick

CFwd on FXS-Ports (mgcp)

hi!
How can I forward the Calls on an Phone witch is connected to an FXS-Port (mgcp, vg200)?
How can I use the other Features, like PickUp etc.
vy Markus

Since there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting.

FXS Ports & Pickup Groups

Is there a way to make an analog phone connected to an FXS port a part of a call pickup group that contains both analog phones & IP phones? I setup a lab and used MGCP to add the gateway and I was able to add the DN associated with the FXS port to a call pickup group. However, I am unable to figure out how to answer the call from the analog phone when another IP phone in the call pickup group is ringing.
Thanks in advance

Hi
You are going down the right track with this.
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1dde5372/0#selected_message
See this other post I made (for a different purpose, but the principal is the same - it just opens up features available to IP phones for FXS ports by registering them using SCCP).
Regards
Aaron
Please rate helpful posts...

Restricting FXS ports to internal calls only

Hi,
I have recently intalled Call Manager 8.5.1 with a H323 Gateway. On the gateway, I have a number of FXS ports for lobby phones. Is there a way I can restrict these phones to allow only internal calls only? Do I need to use COR lists like in Call Manager express or is there a more practical way?
Thanks,
Derek

Hi Derek,
It sounds like these FXS ports are NOT registered to CUCM 8.5.1? If they aren't, then yes COR lists is the most pratical way to do this. You could do a "connection plar xxxx" to a receptionist extension and her her/him forward the calls to the correct extension.

MGCP FXS ports requires a license in CUCM9

Hello!
I am connecting Some analoge phones to VG350 FXS ports which is configured as a MGCP Gateway in CUCM. I beleive MGCP did not requires any license for it. Can some confirm this ? is there any Cisco doc on it ?
Thanks & Regards,

Hi Sambit,
Technically u are correct but legally I think u would be requiring license.
even the ordering guide says Analog devices are supported with Essential USer license and must be purchased through UCL.
http://www.cisco.com/web/partners/downloads/partner/WWChannels/technology/ipc/downloads/finalcopy.pdf
regds,
aman

Door entry system on FXS port of UC320W

Similar Messages

Maybe you are looking for