Dot1x MAB with MDA Issue

I have configured MAB (MAC Authentication Bypass) with MDA (Multi Domain Access). All devices are successfully authenticating with their respective VLAN. MAB devices got authenticating as Voice.
I am using ACS (Radius) for authentication and DHCP relay.
Problem is voice device is not getting IP from DHCP server. There is no error reporting on switch and radius. Without Dot1x everything is working.
switchport access vlan 105
switchport mode access
switchport voice vlan 108
switchport port-security maximum 2
switchport port-security
switchport port-security aging time 2
switchport port-security violation restrict
switchport port-security aging type inactivity
dot1x mac-auth-bypass eap
dot1x pae authenticator
dot1x port-control auto
dot1x host-mode multi-domain
dot1x max-req 1
dot1x guest-vlan 105
spanning-tree portfast
spanning-tree bpduguard enable
ip verify source

we are using 3 Layer model (Core, Distribution & Access) and all VLAN interfaces are on distribution.
I am passing av-pair value device-traffic-class=voice from ACS
We are using ACS 4.1 for windows and ACS is successfully authenticating both devices.
Even show Dot1x Interface shows proper authentication with proper domain

Similar Messages

  • Dot1x/mab multiple clients

    Hi,
    we would to authenticate (with dot1x/mab) more than one mac address on a port. When a user connect his workstation the switch must put the workstation in a vlan and when the user start a vmware in bridge mode the swtich must be put the vmware in a vlan trunk. Can anyone help me, are Cisco Switches able to do this?
    Thanks, Dominik

    Hi Dominik
    You can't run dot1x on a trunk, generally speaking. There's only one scenario where you can run dot1x in a special trunking setup, that is using multi-domain authentication (MDA) using VoIP phones. There are some restrictions to that which you can find out reading through the Config Guide.

  • Impossible to use mAb with Alcatel phone

    Hello
    I try to configure mab authentication with alcatel Phone "ipTouch".
    The radius is an ISE version 1.2.1
    It is impossible to autenticate with mab.
    On the Ise the error is:
        "Event  5434 Endpoint conducted several failed authentications of the same scenario"
        " Failure Reason  11514 Unexpectedly received empty TLS message; treating as a rejection by the client"
    On the switch the error message is:
    2960-09#
    Dec 15 11:13:50.090: %AUTHMGR-5-START: Starting 'mab' for client (0080.9fc8.a9eb) on Interface Gi1/0/11 AuditSessionID
    0A0A510A0000010A2E95860F
    Dec 15 11:13:50.125: %MAB-5-FAIL: Authentication failed for client (0080.9fc8.a9eb) on Interface Gi1/0/11 AuditSessionID
    0A0A510A0000010A2E95860F
    Dec 15 11:13:50.125: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'mab' for client (0080.9fc8.a9eb) on
    Interface Gi1/0/11 AuditSessionID 0A0A510A0000010A2E95860F
    Dec 15 11:13:50.125: %AUTHMGR-7-FAILOVER: Failing over from 'mab' for client (0080.9fc8.a9eb) on Interface Gi1/0/11
    AuditSessionID 0A0A510A0000010A2E95860F
    2960-09#
    Dec 15 11:13:50.125: %AUTHMGR-5-START: Starting 'dot1x' for client (0080.9fc8.a9eb) on Interface Gi1/0/11 AuditSessionID
    0A0A510A0000010A2E95860F
    Here is the switch config
    +++++++++++++++++
    interface GigabitEthernet1/0/11
     description HOST PORT WITH AUTHENTICATION
     switchport access vlan 68
     switchport mode access
     switchport nonegotiate
     switchport voice vlan 78
     authentication event server dead action reinitialize vlan 68
     authentication event server dead action authorize voice
     authentication host-mode multi-auth
     authentication order mab dot1x
     authentication priority dot1x mab
     authentication port-control auto
     authentication periodic
     authentication timer restart 300
     authentication timer reauthenticate server
     authentication timer inactivity server
     mab
     dot1x pae authenticator
     dot1x timeout tx-period 5
     spanning-tree portfast
    end
    global switch config
    +++++++++++++++
    aaa new-model
    aaa authentication login default local group radius
    aaa authentication dot1x default group radius
    aaa authorization exec default local group radius
    aaa authorization network default group radius
    aaa accounting dot1x default start-stop group radius
    aaa server radius dynamic-author
     client 10.1.30.11 server-key 7 023201575A080B34080F
     client 10.1.30.12 server-key 7 122D001B430508116E6A
    dot1x system-auth-control
    dot1x critical eapol
    radius-server attribute 6 on-for-login-auth
    radius-server attribute 8 include-in-access-req
    radius-server attribute 25 access-request include
    radius-server dead-criteria time 1 tries 3
    radius-server host 10.1.30.11 auth-port 1812 acct-port 1813 key 7 0030160A55550F134B60
    radius-server host 10.1.30.12 auth-port 1812 acct-port 1813 key 7 0030160A55550F134B60
    radius-server deadtime 1
    radius-server vsa send accounting
    radius-server vsa send authentication
    Could you please help me.
    Michel Misonne

    Hi
    Yes the mac is in the Identity endpoint.
    During this night, the Phone reboot and now it is OK  !!!
    I do not know why ?
    I changed nothing !
    But here is the debug.
    Also the ise is configured with authentication protocol  Pap-Ascii = Enable
    and "Calling stat id"  and "Check pass" checked."
    The onfig of the phone is
    -Mac to login
    -MD5 profile = OFF
    -Tls Profile OFF
    Her is te debug. ( when it works well)
    conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    2960-09(config)#endshutdown int gigabitEthernet 1/0/11
    2960-09(config-if)#no shu
    2960-09(config-if)#no shutdown
    2960-09(config-if)#
    2960-09(config-if)#
    2960-09(config-if)#
    2960-09(config-if)#
    2960-09(config-if)#end
    2960-09#
    Dec 16 08:33:54.962: %ILPOWER-7-DETECT: Interface Gi1/0/11: Power Device detected: IEEE PD
    Dec 16 08:33:56.157: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/11: Power granted
    2960-09#
    2960-09#
    2960-09#
    2960-09#
    2960-09#
    2960-09#
    2960-09#
    Dec 16 08:33:56.241: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/11, changed state to down
    Dec 16 08:33:56.322: %SYS-5-CONFIG_I: Configured from console by admin on vty0 (10.10.68.4)
    2960-09#
    Dec 16 08:34:02.924: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/11, changed state to up
    Dec 16 08:34:03.924: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/11, changed state to up
    2960-09#
    Dec 16 08:34:05.088: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/11, changed state to down
    2960-09#
    Dec 16 08:34:06.095: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/11, changed state to down
    2960-09#
    Dec 16 08:34:09.800: %AUTHMGR-5-START: Starting 'mab' for client (0080.9fc8.a9eb) on Interface Gi1/0/11 AuditSessionID 0A0A510A0000011E3329AE1E
    Dec 16 08:34:09.800: RADIUS/ENCODE(0000025F):Orig. component type = Dot1X
    Dec 16 08:34:09.804: RADIUS(0000025F): Config NAS IP: 0.0.0.0
    Dec 16 08:34:09.804: RADIUS(0000025F): Config NAS IPv6: ::
    Dec 16 08:34:09.804: RADIUS/ENCODE(0000025F): acct_session_id: 597
    Dec 16 08:34:09.804: RADIUS(0000025F): sending
    Dec 16 08:34:09.804: RADIUS/ENCODE: Best Local IP-Address 10.10.81.10 for Radius-Server 10.1.30.11
    Dec 16 08:34:09.804: RADIUS(0000025F): Sending a IPv4 Radius Packet
    Dec 16 08:34:09.804: RADIUS(0000025F): Send Access-Request to 10.1.30.11:1812 id 1645/198,len 249
    Dec 16 08:34:09.804: RADIUS:  authenticator D3 5F 99 C6 EE 9F 9F 96 - 7C 1B A1 B9 32 1C 78 61
    Dec 16 08:34:09.804: RADIUS:  User-Name           [1]   14  "00809fc8a9eb"
    Dec 16 08:34:09.804: RADIUS:  User-Password       [2]   18  *
    Dec 16 08:34:09.804: RADIUS:  Service-Type        [6]   6   Call Check                [10]
    Dec 16 08:34:09.804: RADIUS:  Vendor, Cisco       [26]  31 
    Dec 16 08:34:09.804: RADIUS:   Cisco AVpair       [1]   25  "service-type=Call Check"
    Dec 16 08:34:09.804: RADIUS:  Framed-IP-Address   [8]   6   10.10.78.250             
    Dec 16 08:34:09.804: RADIUS:  Framed-MTU          [12]  6   1500                     
    Dec 16 08:34:09.804: RADIUS:  Called-Station-Id   [30]  19  "F0-9E-63-E7-E1-8B"
    Dec 16 08:34:09.804: RADIUS:  Calling-Station-Id  [31]  19  "00-80-9F-C8-A9-EB"
    Dec 16 08:34:09.804: RADIUS:  Message-Authenticato[80]  18 
    Dec 16 08:34:09.804: RADIUS:   5F 60 06 35 54 F6 CB 60 3A D6 A9 87 92 F0 0D 70           [ _`5T`:p]
    Dec 16 08:34:09.804: RADIUS:  EAP-Key-Name        [102] 2   *
    Dec 16 08:34:09.804: RADIUS:  Vendor, Cisco       [26]  49 
    Dec 16 08:34:09.807: RADIUS:   Cisco AVpair       [1]   43  "audit-session-id=0A0A510A0000011E3329AE1E"
    Dec 16 08:34:09.807: RADIUS:  NAS-Port-Type       [61]  6   Ethernet                  [15]
    Dec 16 08:34:09.807: RADIUS:  NAS-Port            [5]   6   50111                    
    Dec 16 08:34:09.807: RADIUS:  NAS-Port-Id         [87]  23  "GigabitEthernet1/0/11"
    Dec 16 08:34:09.807: RADIUS:  NAS-IP-Address      [4]   6   10.10.81.10              
    Dec 16 08:34:09.807: RADIUS(0000025F): Started 5 sec timeout
    Dec 16 08:34:09.856: RADIUS: Received from id 1645/198 10.1.30.11:1812, Access-Accept, len 283
    Dec 16 08:34:09.856: RADIUS:  authenticator BC 72 21 F4 37 7D BE B1 - 03 A7 CE F3 3A DB EE DA
    Dec 16 08:34:09.856: RADIUS:  User-Name           [1]   14  "00809fc8a9eb"
    Dec 16 08:34:09.856: RADIUS:  State               [24]  40 
    Dec 16 08:34:09.856: RADIUS:   52 65 61 75 74 68 53 65 73 73 69 6F 6E 3A 30 41  [ReauthSession:0A]
    Dec 16 08:34:09.856: RADIUS:   30 41 35 31 30 41 30 30 30 30 30 31 31 45 33 33  [0A510A0000011E33]
    Dec 16 08:34:09.856: RADIUS:   32 39 41 45 31 45            [ 29AE1E]
    Dec 16 08:34:09.856: RADIUS:  Class               [25]  54 
    Dec 16 08:34:09.856: RADIUS:   43 41 43 53 3A 30 41 30 41 35 31 30 41 30 30 30  [CACS:0A0A510A000]
    Dec 16 08:34:09.859: RADIUS:   30 30 31 31 45 33 33 32 39 41 45 31 45 3A 6D 65  [0011E3329AE1E:me]
    Dec 16 08:34:09.859: RADIUS:   67 61 74 72 6F 6E 2F 32 30 37 35 39 38 39 38 34  [gatron/207598984]
    Dec 16 08:34:09.859: RADIUS:   2F 34 31 30              [ /410]
    Dec 16 08:34:09.859: RADIUS:  Message-Authenticato[80]  18 
    Dec 16 08:34:09.859: RADIUS:   51 E9 8C 07 61 A4 F0 02 0C DC DF 1F 25 BE 39 A3              [ Qa?9]
    Dec 16 08:34:09.859: RADIUS:  Vendor, Cisco       [26]  34 
    Dec 16 08:34:09.859: RADIUS:   Cisco AVpair       [1]   28  "device-traffic-class=voice"
    Dec 16 08:34:09.859: RADIUS:  Vendor, Cisco       [26]  75 
    Dec 16 08:34:09.859: RADIUS:   Cisco AVpair       [1]   69  "ACS:CiscoSecure-Defined-ACL=#ACSACL#-IP-PERMIT_ALL_TRAFFIC-537cb1d6"
    Dec 16 08:34:09.859: RADIUS:  Vendor, Cisco       [26]  28 
    Dec 16 08:34:09.859: RADIUS:   Cisco AVpair       [1]   22  "profile-name=Unknown"
    Dec 16 08:34:09.859: RADIUS(0000025F): Received from id 1645/198
    Dec 16 08:34:09.859: RADIUS/DECODE: parse unknown cisco vsa "profile-name" - IGNORE
    Dec 16 08:34:09.859: %MAB-5-SUCCESS: Authentication successful for client (0080.9fc8.a9eb) on Interface Gi1/0/11 AuditSessionID 0A0A510A0000011E3329AE1E
    Dec 16 08:34:09.863: %AUTHMGR-7-RESULT: Authentication result 'success' from 'mab' for client (0080.9fc8.a9eb) on Interface Gi1/0/11 AuditSessionID 0A0A510A0000011E3329AE1E
    Dec 16 08:34:09.894: RADIUS/ENCODE(00000000):Orig. component type = Invalid
    Dec 16 08:34:09.894: RADIUS(00000000): Config NAS IP: 0.0.0.0
    Dec 16 08:34:09.898: RADIUS(00000000): sending
    Dec 16 08:34:09.957: RADIUS/ENCODE: Best Local IP-Address 10.10.81.10 for Radius-Server 10.1.30.11
    Dec 16 08:34:09.957: RADIUS(00000000): Sending a IPv4 Radius Packet
    Dec 16 08:34:09.957: RADIUS(00000000): Send Access-Request to 10.1.30.11:1812 id 1645/199,len 147
    Dec 16 08:34:09.957: RADIUS:  authenticator 1B D7 D2 13 EF 69 36 E2 - 87 4D A9 69 2A F7 29 4D
    Dec 16 08:34:09.957: RADIUS:  NAS-IP-Address      [4]   6   10.10.81.10              
    Dec 16 08:34:09.957: RADIUS:  User-Name           [1]   41  "#ACSACL#-IP-PERMIT_ALL_TRAFFIC-537cb1d6"
    Dec 16 08:34:09.957: RADIUS:  Vendor, Cisco       [26]  32 
    Dec 16 08:34:09.957: RADIUS:   Cisco AVpair       [1]   26  "aaa:service=ip_admission"
    Dec 16 08:34:09.961: RADIUS:  Vendor, Cisco       [26]  30 
    Dec 16 08:34:09.961: RADIUS:   Cisco AVpair       [1]   24  "aaa:event=acl-download"
    Dec 16 08:34:09.961: RADIUS:  Message-Authenticato[80]  18 
    Dec 16 08:34:09.961: RADIUS:   E7 15 BB FB 7B 5B 1A C4 50 FC E7 0E 10 AC 22 36             [ {[P"6]
    Dec 16 08:34:09.961: RADIUS(00000000): Started 5 sec timeout
    Dec 16 08:34:09.968: RADIUS: Received from id 1645/199 10.1.30.11:1812, Access-Accept, len 209
    Dec 16 08:34:09.968: RADIUS:  authenticator FA 03 DD C1 D2 87 6B 58 - 99 65 EE 96 FF D5 76 FD
    Dec 16 08:34:09.968: RADIUS:  User-Name           [1]   41  "#ACSACL#-IP-PERMIT_ALL_TRAFFIC-537cb1d6"
    Dec 16 08:34:09.968: RADIUS:  State               [24]  40 
    Dec 16 08:34:09.968: RADIUS:   52 65 61 75 74 68 53 65 73 73 69 6F 6E 3A 30 61  [ReauthSession:0a]
    Dec 16 08:34:09.971: RADIUS:   30 31 31 65 30 62 30 30 30 30 30 30 37 38 35 34  [011e0b0000007854]
    Dec 16 08:34:09.971: RADIUS:   38 46 45 45 38 31            [ 8FEE81]
    Dec 16 08:34:09.971: RADIUS:  Class               [25]  54 
    Dec 16 08:34:09.971: RADIUS:   43 41 43 53 3A 30 61 30 31 31 65 30 62 30 30 30  [CACS:0a011e0b000]
    Dec 16 08:34:09.971: RADIUS:   30 30 30 37 38 35 34 38 46 45 45 38 31 3A 6D 65  [00078548FEE81:me]
    Dec 16 08:34:09.971: RADIUS:   67 61 74 72 6F 6E 2F 32 30 37 35 39 38 39 38 34  [gatron/207598984]
    Dec 16 08:34:09.971: RADIUS:   2F 34 31 31              [ /411]
    Dec 16 08:34:09.971: RADIUS:  Message-Authenticato[80]  18 
    Dec 16 08:34:09.971: RADIUS:   A4 02 84 1E 1A 97 E9 E9 DE 46 93 D6 30 C4 52 99               [ F0R]
    Dec 16 08:34:09.971: RADIUS:  Vendor, Cisco       [26]  36 
    Dec 16 08:34:09.971: RADIUS:   Cisco AVpair       [1]   30  "ip:inacl#1=permit ip any any"
    Dec 16 08:34:09.971: RADIUS(00000000): Received from id 1645/199
    Dec 16 08:34:10.069: %AUTHMGR-5-SUCCESS: Authorization succeeded for client (0080.9fc8.a9eb) on Interface Gi1/0/11 AuditSessionID 0A0A510A0000011E3329AE1E
    Dec 16 08:34:10.069: RADIUS/ENCODE(0000025F):Orig. component type = Dot1X
    Dec 16 08:34:10.069: RADIUS(0000025F): Config NAS IP: 0.0.0.0
    Dec 16 08:34:10.069: RADIUS(0000025F): Config NAS IPv6: ::
    Dec 16 08:34:10.073: RADIUS(0000025F): sending
    Dec 16 08:34:10.073: RADIUS/ENCODE: Best Local IP-Address 10.10.81.10 for Radius-Server 10.1.30.11
    Dec 16 08:34:10.073: RADIUS(0000025F): Sending a IPv4 Radius Packet
    Dec 16 08:34:10.073: RADIUS(0000025F): Send Accounting-Request to 10.1.30.11:1813 id 1646/240,len 423
    Dec 16 08:34:10.073: RADIUS:  authenticator 6C 75 45 C7 B7 66 2F 4D - 04 01 C6 CE A5 16 68 9B
    Dec 16 08:34:10.073: RADIUS:  Acct-Session-Id     [44]  10  "00000255"
    Dec 16 08:34:10.073: RADIUS:  Calling-Station-Id  [31]  19  "00-80-9F-C8-A9-EB"
    Dec 16 08:34:10.073: RADIUS:  Vendor, Cisco       [26]  49 
    Dec 16 08:34:10.073: RADIUS:   Cisco AVpair       [1]   43  "audit-session-id=0A0A510A0000011E3329AE1E"
    Dec 16 08:34:10.073: RADIUS:  Framed-IP-Address   [8]   6   10.10.78.250             
    Dec 16 08:34:10.073: RADIUS:  User-Name           [1]   14  "00809fc8a9eb"
    Dec 16 08:34:10.073: RADIUS:  Vendor, Cisco       [26]  32 
    Dec 16 08:34:10.073: RADIUS:   Cisco AVpair       [1]   26  "connect-progress=Call Up"
    Dec 16 08:34:10.073: RADIUS:  Vendor, Cisco       [26]  21 
    Dec 16 08:34:10.073: RADIUS:   Cisco AVpair       [1]   15  "lldp-tlv=    "
    Dec 16 08:34:10.073: RADIUS:  Vendor, Cisco       [26]  25 
    Dec 16 08:34:10.073: RADIUS:   Cisco AVpair       [1]   19  "lldp-tlv=        "
    Dec 16 08:34:10.073: RADIUS:  Vendor, Cisco       [26]  23 
    Dec 16 08:34:10.073: RADIUS:   Cisco AVpair       [1]   17  "lldp-tlv=      "
    Dec 16 08:34:10.073: RADIUS:  Vendor, Cisco       [26]  28 
    Dec 16 08:34:10.073: RADIUS:  Vendor, Cisco       [26]  28 
    Dec 16 08:34:10.073: RADIUS:  Tunnel-Packets-Lost [86]  101 1852075890               
    Dec 16 08:34:10.076: RADIUS:  Nas-Identifier      [32]  32  "             
    Dec 16 08:34:10"
    Dec 16 08:34:10.076: data_left 15
    2960-09#
    Dec 16 08:34:10.076: RADIUS(0000025F): Started 5 sec timeout
    Dec 16 08:34:10.090: RADIUS: Received from id 1646/240 10.1.30.11:1813, Accounting-response, len 20
    Dec 16 08:34:10.090: RADIUS:  authenticator 91 9F CE 71 1C 4B 45 93 - 49 86 52 C8 C3 44 40 B8
    2960-09#
    Dec 16 08:34:11.485: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/11, changed state to up
    Dec 16 08:34:12.485: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/11, changed state to up
    2960-09#
    2960-09#
    2960-09#
    2960-09#
    2960-09#
    2960-09#
    2960-09#sh auth
    2960-09#sh authentication ses
    2960-09#sh authentication sessions int gi
    2960-09#sh authentication sessions int gigabitEthernet 1/ /0/11
                Interface:  GigabitEthernet1/0/11
              MAC Address:  0080.9fc8.a9eb
               IP Address:  10.10.78.250
                User-Name:  00809fc8a9eb
                   Status:  Authz Success
                   Domain:  VOICE
           Oper host mode:  multi-auth
         Oper control dir:  both
            Authorized By:  Authentication Server
                  ACS ACL:  xACSACLx-IP-PERMIT_ALL_TRAFFIC-537cb1d6
          Session timeout:  N/A
             Idle timeout:  N/A
        Common Session ID:  0A0A510A0000011E3329AE1E
          Acct Session ID:  0x00000255
                   Handle:  0x3600011F
    Runnable methods list:
           Method   State
           mab      Authc Success
           dot1x    Not run
    2960-09#

  • I have an older iMAC that once burned CD's with no issues. Now I get an error message saying "The attempt to burn a disc failed. The device is not accessible, probably because it was removed". I have never had it touched so the device was not removed.Help

    I have an olde iMac that once I have an older iMAC that once burned CD's with no issues. Now I get an error message saying "The attempt to burn a disc failed. The device is not accessible, probably because it was removed". I have never had it touched so the device was not removed. Please advise as to what could be the problem. How to fix. Thanks

    Try resetting the SMC and PRAM first, if that doesn't help try a cleaning disc.....and then buy an inexpensive external burner. Slimline super drive failures are all too common.
    To reset the SMC
    Shut down the computer.
    Unplug the computer's power cord.
    Wait fifteen seconds.
    Attach the computer's power cord.
    Wait five seconds, then press the power button to turn on the computer.
    Resetting NVRAM / PRAM
    Shut down your Mac.
    Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.

  • Question for those with memory issues on k8n neo plat

    I have been having issues with my memory on the k8n neo platinum board since i built the system last month and i just recently discovered a fact I had overlooked.
    I Have discovered that  if i test the system while it is cool (having sat turned off overnight for example), then memtest will pass the ram just fine and the system will be stable for a short period of time, generally longer if no intensive applications are used, ie. doom3 vs. websurfing).
    This system, once it heats up ( seems mostly to be the nvidia 3 nb that needs to be "hot"- that is, a probe placed in contact with the module reaches about 58+ degrees c) then the system becomes unstable and memtest, if used, fails.
    Prime95, if used on it when its cool, will usually take about an hour or so to fail, but if its used on the system when its been running a bit ( temps from nb at 58c+ and memory module hot to the touch) then it fails after about 20-30 seconds.
    I have placed an active hs on the nb in an attempt to correct this, but temps still remain high with failures occuring.
    I have spent the better part of three days testing the sytem this way and the above facts have held true in all these tests.
    I have  tested at stock ratings ( not using "auto" in bios, but using "approved ratings" of 10 x 200 for fsb and timings of 2-3-3-7 for my ram at 1:1 (which is recommended as well) since i am testing for base stability at this point;Voltages have been left at auto settings, however.
    I was wondering if anyone else with memory issues could try this out and post if this seems to be the case for you as well.
    Perhaps the memory issues on these boards are directly related to a problem with the nvidia 3 chipset running too hot?
    Does anyone have a memory issue with these boards who is using water cooling on the NB ?
     Lack of issues from people using 'problem" memory, but having no failures with water cooled nb's would support my assumption.

    Yes i did mean chipset.  
    I am using a stock hs/fan from amd, which seems to run a tad hot but, considering that I wont overclock until I can get board stable, its not an issue. (runs 35-40 idle and up to 72 intensive). I need the warranty more then the extra mhz at present.
    I removed the stock heatsink from the nvidia chipset and bought a generic chipset cooler (green, very little in the way of fins and seems to be aluminum) with a small fan.
     I used a generic silver paste from Compusa to adhere both the cpu hs and the chipset.
    I didnt lap either hs, just installed each as per instructions on artic silvers website (figured it had to go on the same way even generic).
    I also bought a kingwin thermal center which i ran probes from to the cpu, case, and nb chipset.
     I am not using it to adjust fans so those arent connected - its just a reference temp I can see at a glance, esp considering the funky bios reading this boards been known to give.
    I assume from these responces that even a nvidia 3 250 chipset shouldnt get as hot as mine?
    I asked about that from the retailer i bought this from but he seemed to think it was "ok" at 50ish celcius, but then again he didnt look too confident when he said it, lol.
    Idle right now reads on Corecenter at 28 celcius for cpu and 33 celcius for the chipset, although, I have readings of 37 c and 43 c from the kingwin thermal center, which i believe to be more accurate.
    My voltage reads at 11.67 for the 12v line at idle right now.
    The psu i got is stick from the xblade case i bought in store. (http://www.xoxide.com/xblade2.html)
    I have a dvd burner, cd drive, and two maxtor ide hd's attached to the system;The only card is the agp.
    Is there a way to check and see if the cpu ispower starved? software monitor or even an external probe perhaps?
    I havent put a probe on it, but the ram came in its own heatspreader, which gets very hot to the touch as well.
    What temps should I be looking for on these items?

  • Is there an issue with the hitachi hard drives in the MacBook Pro's ?  Got a 15 inch and a 13 inch at the same time and both drives have failed in under two years. I have heard from a few other people with same issue.

    Is there an issue with the hitachi hard drives in the MacBook Pro's ?  Got a 15 inch and a 13 inch at the same time and both drives have failed in under two years. I have heard from a few other people with same issue. Other drive I have had have lasted at least 5 or more years.

    there is a dylib you can put in the springboard if jailbroken but if not you have to find an apple store

  • Sales orders with credit issues taking availability stock

    Hi,
    I am doing confirmation using Global ATP in APO. The confirmation is well done, but the confirmed quantity for sales orders with clients that have credit issues is taken the available sotck for other sales orders with ok clients that I want to confirm the quantity they ordered.
    For example:
    Stock: 10 PC
    Client A order 15 PC and 10 are confirmed, but the ordered is retained becuse of credit issues with client A.
    Then client B order 3 PC, but nothing is confirmed because the ordered for client A is reserving the stock (note: this would be ok if client A had not credit issues).
    So, I want that the 3 PC for client B are confirmed and the 10 PC not reserved for the cient A while client A has credit issues.
    How could I configured, so that the orders with credit issues do not reserve stock for the incoming orders?
    Thanks a lot.

    Hi DB49,
    thanks for the quick answer.
    I checked the configuration in the R3 and seems to be fine. To prove it, I disconnect APO and did the availability check in the R3 system and it is working fine; the orders quantities that are blocked because of credit issues, do not reserve stock for incoming orders.........son new incoming orders are well confirmed.
    But after connecting APO the problem continues. I checked the next points.
    In R3 transaction CO09: takes to the APO screen and you see the ATP available quantity OK (do not consider the quantities of the credit issues orders). But at the moment that you make the order (VA01) it does not confirm any stock and if you select the line and go to the ATP screen (the same you get from the CO09) the quantities of credit issues orders are taken into account..the ATP availability quantity changes from the first going directly from the CO09.
    What could it be?
    Note: it was working fine with APO, I started to have the issue after implementing note 1262475 in APO. This note was becuase the BAPI_APOATP_CHECK was not brigning any value for the ATPQTY_***.
    Thanks a lot!!!

  • Report with grouping issue

    I have a report which have year(2008), Category(0-1,2-3, ALL), product(0,1,2,3,4..), % sales. I group by all the category elements and called it as All, I am not getting the right percentage sales for the Category ALL other wise for 0-1,2-3 i am getting it right. Please advise where i am doing it wrong. please find the blog for a screen shot of my issue.
    http://ravibiblog.blogspot.com/2012/04/report-with-grouping-issue.html
    Thanks,
    RC

    Pl post details of OS, database and EBS versions. Pl see if these MOS Docs can help
    FARXPBSH Failing With "Program was terminated by signal 11" or "Program was terminated by signal 10"          (Doc ID 742729.1)
    Publishing RXAPPYAC: The FARXPBSH Ends With 'Signal 11' Error          (Doc ID 432797.1)
    RXi RX Reports Failing With Program Was Terminated By Signal 10 or 11 Errors After FA Rollup Patch 6          (Doc ID 737963.1)
    Program was Terminated by Signal 11 when Running Rxi Reports          (Doc ID 559425.1)
    HTH
    Srini

  • I am using Windows 7 Home Premium 64-bit OS.  I've never had this problem before... today I opened iTunes and it prompted me to download the newest version.  I use iTunes all the time and have updated it multiple times with no issues.  During the installa

    I am using Windows 7 Home Premium 64-bit OS.I've never had this problem before... today I opened iTunes and it prompted me to download the newest version.  I use iTunes all the time and have updated it multiple times with no issues.  During the installation process it gave me an error message that said: 
    Runtime error! 
    Program C:\Program Files\iTunes.exe
    R0634
    An application has made an attempt to load the C runtime library incorrectly.
    Please contact the application's support team for more information.
    I quit the installation, uninstalled iTunes and rebooted my computer.  I now receive a similar message with a slight difference:
    Runtime error! 
    Program C:\Program Files (x86)...
    R0634
    An application has made an attempt to load the C runtime library incorrectly.
    Please contact the application's support team for more information.
    I did not leave anything out from the error message.  It doesn't point to a specific file, it just ends with "(x86)..."  Every time I boot up my computer, this error message pops up on my desktop.
    How do I repair this issue?  I have found multiple suggested solutions but am unsure which one is the best, and I don't want to try a bunch of different things for fear I may make the problem worse.  I would like to try and fix this myself if possible but I need to know if that is really possible or if I need to take my computer to someone for repairs.  Any suggestions will be greatly appreciated!!

    Hi lustyln,
    I'm having a little trouble understanding all of what you are trying to explain. From what I can tell, it sounds like your PC has a lot of software problems and you want to know what is supposed to be there and what isn't.
    For reference, here are your product specifications:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01893242&lc=en&product=4043282
    To get your PC software back to how it was when it was first purchased, run a system recovery:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01867418&lc=en&product=4043282
    I hope this helps.
    ...an HP employee just trying to help where I can, but not speaking on behalf of HP.

  • After upgrading to mountain lion i keep getting an error message saying my startup disc is full. it shouldnt be full because there is barely anything on there and i was running windows with bootcamp prior to this with no issues

    after upgrading to mountain lion i keep getting an error message saying my startup disc is full. it shouldnt be full because there is barely anything on there and i was running windows with bootcamp prior to this with no issues. my computer now freezes and programs close randomly. The usual command for opening windows with bootcamp doesnt work. once in restarted my computer after it froze and it rebooted in windows automatically. i really just want to know if there is a way to take the upgrade off my laptop because it is very annoying.

    Hi Memalyn
    Essentially, the bare issue is that you have a 500GB hard drive with only 10GB free. That is not sufficient to run the system properly. The two options you have are to move/remove files to another location, or to install a larger hard drive (eg 2TB). Drive space has nothing to do with SMC firmware, and usually large media files are to blame.
    My first recommendation is this: download and run the free OmniDiskSweeper. This will identify the exact size of all your folders - you can drill down into the subfolders and figure out where your largest culprits are. For example, you might find that your Pictures folder contains both an iPhoto Library and copies that you've brought in from a camera but are outside the iPhoto Library structure. Or perhaps you have a lot of purchased video content in iTunes.
    If you find files that you KNOW you do not need, you can delete them. Don't delete them just because you have a backup, since if the backup fails, you will lose all your copies.
    Don't worry about "cleaners" for now - they don't save much space and can actually cause problems. Deal with the large file situation first and see how you get on.
    Let us know what you find out, and if you manage to get your space back.
    Matt

  • My mac air will not connect to the internet. There is an exclamation point in the wifi icon and when i go into preferences i see that it is setting its own IP address. I have a macbook that is able to connect with no issue. HELP

    My macbook air will not connect to the internet. There is an exclamation point in the wifi icon and when i go into preferences i see that it is setting its own IP address. I have a macbookpro that is able to connect with no issue. HELP

    Reset the TC to factory and start again.
    Use all SMB type names for wireless and base station.. Not apple type names.. this is more important since Mavericks.
    I also recommend different names for the different bands.
    So for example.
    TC name.. TCgenx (I use whatever the generation number is for the x.. eg TCgen4 or latest one TCgen5)
    WIreless name.. TC24ghz for 2.4ghz
    TC5ghz for 5ghz
    You can also set the channel manually.
    If you still have issues.. start with no security and then if it fails to connect there is something seriously wrong with the laptop. Did you upgrade install Mavericks?? That can lead to driver issues.. I would recommend a clean install.

  • HT1365 Hi can anyone help with this issue regarding my wireless magic mouse? When im on google chrome and scrolling down the page i always have youtube running in the background but the audio cuts/spits/pops can anyone help me with this?

    Hi can anyone help with this issue regarding my wireless magic mouse? When im on google chrome and scrolling down the page i always have youtube running in the background but the audio cuts/spits/pops can anyone help me with this?

    The figures you mention only make sense on your intranet.  Are you still using the same wireless router.  The verizon one is somewhat limited as far as max wireless-n performace.  For one thing it only has a 2.4 radio.   I like many people who wanted wireless-n performance before they even added a wireless-n gigabit router, have my own handling my wireless-n network.

  • A suggestion for those with battery issues:

    When I first got my iPhone, I had the same battery issues many people here are talking about, in fact I posted about it myself. Its fixed. Very fixed, and Im very happy with my battery life. Here is what I did.
    First, do not charge it using your USB connection. At least not always. Why? I dont know. I did the first few days, and couldnt get a full charge even tho system wasnt going to sleep. I started using the wall charger, and got longer battery life, but still not great. One night, I forwarded the phone to my home phone in case I got a call, and shut the phone down completely, and put it on charge. In the morning, I woke up to a 100% charged, fully glowing battery icon. The battery lasted all day with no issues. Every night after that, I just charged it on the wall charger, but did NOT shut it down to see what happened. I am still waking up every morning to a 100% fully charged battery. The battery life seems to get better daily now.
    Today, I ran wifi for about 5 hours because I forgot to shut it off. This was after going to the pool and listening to the iPod on the phone for about 2 hours. And using the phone normally throughout the day, checking mail, sms, etc. Really a full day of work, and my battery is still over 50% full. I purposely didnt connect it to anything during the day for a recharge, not the USB or wall charger.
    Good luck, hope this helps. Id be interested to know if it does.

    Here's my non-scientific experiment.
    After surprising battery drain for the first 10 days or so with not much usage, I completely drained the battery yesterday until the phone shut off.
    I plugged into AC charge and was worried when it didn't seem to even begin charging.
    I plugged into USB, assuming it needed to charge enough to at least complete a sync.
    I left it on USB until about 5-10% charge, then switched it to AC. At about 50% I needed to use it, so I did but sparingly, and put it back on charge, all the while keeping Mail on manual and WiFi off.
    I took it off once more to get it home from the office, then plugged into AC.
    I left that charging overnight.
    I never actually got the "glow", but did get the plug icon showing full charge in the status bar.
    After about 2 1/2 hours this morning, the status has not moved off of 100% (but with little usage as before).
    This is definitely an improvement already though. Hope this helps.

  • I can't be the only one with this issue. MacBook Pro Retina Late-2013 WiFi disconnects after waking up from sleep.

    Did anyone buy a MacBook Pro Retina 13" from Best Buy this Black Friday?
    I'm having an issue where the WiFi disconnects after the MacBook wakes from sleep but only after a couple of minutes.
    Once the WiFi disconnects, I can't reconnect to the same network and sometimes it won't find nearby networks.
    I have to turn off the WiFi and wait for at least 5 seconds before turning it back on for it to auto-reconnect to my home network.
    If I wait less than 5 seconds, it will continue to attempt connection to the home network but won't connect.
    I've tried reformatting and deleting my network configurations as well as resetting my modem, power cycling it, etc.
    I am using 2Wire Gateway modem/router from AT&T on b/g network.
    I've tried connecting to a friend's network under Time Warner Cable and the same issue occurs.
    I exchanged the MacBook at a Best Buy for a brand unopened one (I hope) and the same exact thing happens with this new one.
    Really, I can't be the only one with this issue. Unless in a 0.00001% chance I received two defective units in a row?
    Please.. does anyone have a clue why this is happening?

    You're definitely not the only one.  I have the same issue.  I spent 6 hours over multiple days on the phone with Apple support trying a variety of things (some of which are mentioned above), and none of them worked.  They finally sent me a replacement laptop.  I made sure to try it periodicaly as I was moving files and installing applications to see if I ran into it again and things seemed okay at first but now I am running into the same issue and it is terribly annoying.  I've got 5 other devices that connect to the same router and I've never had this issue with any of them.
    My router is a Linksys E2000.  I haven't tried changing the router channel but I have tried to cnnecting to other networks in the building I live in and I have run into the same issue there.

  • Itunes 10.6.3 - Just update to the new Itunes and the album artwork is not sticking anymore... I upload the artwork and when I change songs and go back the art is gone. Anyone with similar issue ?

    Itunes 10.6.3 - Just update to the new Itunes and the album artwork is not sticking anymore... I upload the artwork and when I change songs and go back the art is gone. Anyone with similar issue ?

    I have this issue.  Album artwork was totally fine before.  After this update, it is all messed up and even got messed up when transferred to my iphone.
    iTunes doesn't have the artwork anymore, but then iPhone has it but shows wrong artwork with wrong albums.
    Please fix!

Maybe you are looking for

  • How to migrate from BE6000 to Communications Manager

    Dear forum members, first of all, I'am tired. I have been on a long journey from the day we bought our Cisco Unified Communication system until now. Technically everything worked just fine, right from the beginning until now. But starting from the fi

  • Handling Unit problem in Packing for STO

    Hello All, The problem is related to Packing process in case of Stock Transfer Order (STO).After making delivery while doing the packing procedure, in " Handling Unit " supplements 'Handling Unit Group 1' field  is not getting populated / assigned au

  • OLEDB 8i against Oracle 9i Database

    Is it recommended to use Oracle Provider for OLE DB 8i driver against Oracle 9i Database server? Does anyone have an official Oracle link whether this is supported or not. Thanks Dipak

  • What currently available charger will power a 2005 Mac mini G4?

    I have a late 2005 Mac mini and need to replace the power adaptor - any idea which of the currently available models will work or where I can get a non-apple version?

  • JMS Newbie

    Hi Guys, I am newbie in JMS. Is there any way I can do Hello World with JMS in my local System..Like setting up my own Que server in local machine Thanks in advance for you time Arby_pv