Down convert labview 2011 to 2009

Hi,
I have a series of VIs that I made for my mechatronics honours thesis project. However, when tested on the target PC, I discovered that it has version 9.0, whereas the VIs are version 11.0, hence the request for a conversion. I really appreciate any help,
Thank-you
Allan
(The VIs are in the attached zip file)
Solved!
Go to Solution.
Attachments:
TrekFunctionGenerator.zip ‏379 KB

can anyone do the downconversion from labview 2011 to labview 2009 for the following driver.
THanks in advance
Attachments:
mk1000(USB)2.3-profile(labview2011).zip ‏548 KB

Similar Messages

Please convert Labview 2011 file to Labview 7.0

Please convert Labview 2011 file to Labview 7.0. Thanks alot!
Attachments:
FreqResponse.vi ‏104 KB

attached
You will need to replace the front-panel graph. Downconversion sometimes corrupts graphs.
Attachments:
FreqResponse.vi ‏299 KB

Downconvert from LabView 2011 to 2009

Hi !
Can anyone convert these VIs (attached file) from Labview 2011 to LabView 2009 ?
Thanks a lot.
DMONS
Solved!
Go to Solution.
Attachments:
LCC25 driver for LabView 2011.zip ‏4308 KB

Here you go.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
LCC25 driver for LabView 2009.zip ‏4230 KB

Convert from LabVIEW 2011 to LabVIEW 9.0

Please convert from LabVIEW 2011 to LabVIEW 9.0
Attachments:
Watlow Vis.zip ‏76 KB

Looks like somebody forgot to attach the zip file. Here you go.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
Watflow.zip ‏57 KB

I want to convert my source code in Labview 5.1 to labview 2011

HI
I want to convert a labview program which is in labview 5.1 to labview 2011 version
i am not able to open the program in the 5.1 version.
if there is no way to convert it ,then can you tell me if 5.1 version is avialable online that is compatible with the windows7 .?
thanks
Attachments:
plant.vi ‏31 KB
PID.vi ‏104 KB
integration3.vi ‏18 KB

Post your request in this Version conversion Board
The best solution is the one you find it by yourself

Convert TCPIP_Nagle_algorithm.zip from LabVIEW 2012 to LabVIEW 2011

Hello,
can somebody convert the VIs in the zip file from LabVIEW 2012 to LabVIEW 2011 please. I need them to study.
Thank you very much for your support.
Solved!
Go to Solution.
Attachments:
TCPIP_Nagle_algorithm.zip ‏63 KB

Additionally I am sorry that I have put my post in LabVIEW and not under Version Conversion

Please Convert tktds5xx from LabView 2012 to LabView 2011.

I was directed here to have an instrument driver converted from LabView 2012 to LabView 2011.
Thanks in advance!
Solved!
Go to Solution.
Attachments:
tktds5xx.zip ‏777 KB

Here you go.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Attachments:
tktds5xx.zip ‏529 KB

Please Convert Vis from Labview 2013 to Labview 2011

Please convert the attached Vis from Labview 2013 to Labview 2011
Solved!
Go to Solution.
Attachments:
Convert from2013 to 2011.zip ‏255 KB

Here you go.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Attachments:
Converted to 2011.zip ‏176 KB

FM down converter in LabView. How?

Hello NI Developers!
I have Frequency Modulated (FM) Signal, with carrier frequency 1000Hz and message signal frequency 20Hz. I want to downconvert FM signal frequency to 200Hz. I searched through the forum and google and didn't find anything where would be at least algorithms or Math equations. How to downconvert FM signal?
The aim is down convert signal to low frequencies where it is easier to filter from noise.
Thank you in advance!
Solved!
Go to Solution.

Hello,
You could try using the Scale Delta t VI (Functions >> Programming >> Waveform). As the help says, "Multiplies the delta t component of the waveform by the specified scale
factor. Generally, this lengthens or shortens the sample rate of the
waveform."
You could also take a look at the Resample Waveforms (continuous) VI (Functions >> Signal Processing >> Waveform Conditioning.
I hope this helps.
Vivek Nath
National Instruments
Applications Engineer
Machine Vision

Convert VI Labview 5.1 to Labview 2011

Hi.
I've attached three VIs (within a zip file) I can no longer access due to version conflicts.
I would really appreciate a conversion given I do not have the intermediate software.
-Matt
Solved!
Go to Solution.
Attachments:
connectionstoolkitvis.zip ‏53 KB

There's a library missing, but here's the VIs converted to 2011.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
connectionstoolkitvis.zip ‏53 KB

How to start an 8.2 app in LabVIEW 2011

This has been a problem that I've been trying to deal with for the past week to no avail.
In short:
The 8.2s which worked on an XP machine were openned on a Windows 8 with LabVIEW 2011, made into an executable, put back on to the Windows XP to see if it will still all worked, and it does not.
In detail:
I had a ready made, working application made in LabVIEW 8.2. The goal is to update all old software to the new LabVIEW 2011, but to still make it work. The problem is, after making it run in edit mode for at least a little bit (after debugging common errors with openning in a newer version), after making an executable and putting it on the machine it used to run on, it won't run. The program will not communicate with the machine and will give the following errors which are, my eyes, things that should not be happening after working in edit mode.
Two error codes received:
1) One or more Configuration File(s) are not available. Please Check the Hardware configuration!
2) {
Error 7 occured at Openfile+.vi: Open file
Possible reason(s):
LabVIEW: File not found. The file might have been mover or deleted, or the file path might be incorrectly formatted for the operating system.
For example, use\ as path separators on Windows, : on Mac OS X, and / on Linus. Verify tht the path is correct using the command prompt or file explorer.
=========================================
NI-488: Non-existent board.
Please, if anyone has had the same or a similar issue and can give any sort of feedback or thoughts, I would greatly appreciate it. Thank you!
-Hub25

Bob_Schor wrote:
There are a number of issues here. First, LabVIEW 8.2 cannot be installed on Windows 7 (to say nothing of Windows 8), and LabVIEW 2011 cannot be installed on Windows XP. I'm not sure whether executables can be built across Windows 7/XP boundaries, but I'm pretty sure that, at a minimum, you'd need to install the LabVIEW 2011 Run Time Engine on the Windows XP system (and I don't know if this is possible).
After next April, Windows XP "turns into a pumpkin" as Microsoft drops support for it. A good time to migrate to Windows 7!
You can install LabVIEW 8.2 on a Windows 7 computer. I have that right now specifically for converting old code. And I am sure LabVIEW 2011 can go on XP as well.
I'm guessing the main issue is the lack of the 2011 Run-Time Engine on the XP machine. But I would also advise moving away from the OpenFile+.vi since that is a really old VI and the newer LabVIEW file I/O primitives are so much better anyways.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Labview 2011 save for previous version crashes

Hello,
I am trying to save an existing Labview 2011 project to any previous version. I have tried 2010 all the way down to 8.0. I have a clean project, all files are LV 2011, it builds and runs correctly. I have mass compiled. It did call 2 dynamic vi's but I have removed those. The project did contain conditional compilation, but that is removed. It did contain disabled diagrams, but they are removed. I did a save hierarchy to a seperate folder, just to make sure the standard save works. It does. There are 1196 vi's and controls in the project.
If I save to LV 2010, quite a number of sub vi's are saved (909 including controls), but none of the top level ones. The crash is manifested by Labview leaving memory (task manager doesn't see it any more) and the Labview window dissapearing.
Attached is the save dialog at the instance before crashing.
I have not been able to locate a log to let me know the last loaded vi. If you know of such a log, please let me know.
Has anyone experienced similar problems? If so, any clues on how to fix this?
Thanks,
Bart Schroder
Attachments:
LV2011 save crash.jpg ‏17 KB

BartSchroder wrote:
I have not been able to locate a log to let me know the last loaded vi. If you know of such a log, please let me know.
In the advanced build configuration, check "generate build log file". See if you get more information. Good luck.
Quote from the help:
Generate build log file—Specifies whether to create a log file for the build. The build log file lists all files contained in the build, including subVIs you do not specify as Startup VIs or Always Included. The log file also contains general build information such as build start and end time, the build specification and project name, and any errors that occurred during the build.
LabVIEW Champion . Do more with less code and in less time .

Serious Bugs in LabVIEW 2011

Dear Sir or Madam,
I have been working with LabVIEW for 10 years.
recently I have istalled the last version (LabVIEW 2011) and encountered some fundamental Bugs as bellow:
1-when I want to close LabVIEW 2011 Platform,it taks about 3 sec time to be closed ! while this was not in earlier version such as LabVIEW 9 sp1.
2-In a typical Front Panel,when I press Ctrl+M to chenge to Run mode,it went but after pressing Ctrl+M again,it will not exit from run mode(THIS BUG HAPPEN SOME TIMES NOT ALWAYS) or when I do right-click to view Function pallet or Control pallet,nothing happen!(THIS BUG HAPPEN SOME TIMES NOT ALWAYS).
I will be happy if you tell me what is the reasons and can I trust on LabVIEW 2011 for big projects or It is better for me to used LabVIEW 2009 as the past.
thank you for your kind attention.
Regards,
Ata Rahai,
Specialist Engineer.

Hi
I believe that 2011 is a very stable version (I was beta testing) and in my system the CtrlM works both ways, always.
Taking a few seconds to close is normal since version 8.0, depending on how many services are running. LV does clean up the system.
greetings from the Netherlands

LabVIEW 2011 Development System fails to install

I have just tried several times to install my new copy of LabVIEW 2011 Dev Suite, but get an unknown exception (with no details - see attached picture) right at the start of installing the development system (English 32-bit). I have rebooted and closed all applications including virus scanning but still the same. I am using WinXP Pro SP3, and already have LV 8.6, 2009, and 2010 installed. I'm completely baffled as this type of problem has never occurred before and there is no information about the cause of the exception.
Mike
Solved!
Go to Solution.
Attachments:
LV2011 Unknown Exception.JPG ‏10 KB

Hi John,
After clicking on Details, the words "No information" or similar are displayed. I have tried again today but with the same result. I have attached a new screenshot showing the installer initialisation progress window. I have checked the DVD and it looks undamaged, and there is plenty of free disk space.
Attachments:
LV2011 Unknown Exception.JPG ‏64 KB

Conversion from Labview 12 to Labview 2011

This an example file I downloaded from the tutorial but it's only available in LabView 12. I would like to see the example they provided in Labview 2011. Any help would be appreciated. Thank You!
Sorry, there were multiple files and it was compiled into a zip file.
Or can someone teach me to convert it?
Attachments:
heart_rate_monitor_example.zip ‏182 KB

Here you go
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
Heart Rate Monitor Project.zip ‏146 KB

Down convert labview 2011 to 2009

Similar Messages

Maybe you are looking for