Downgrading 5508 from 7.0.116.0 to 7.0.98.218

Hi all, I've just gotten in two new 5508 controllers that have come preinstalled with code version 7.0.116.0. My issue is that when I go to downgrade these to 7.0.98.218 I get an error after the Image version check is passed stating the following:
ERROR: Incompatible SW image.
ERROR: Please install the Data Payload Encryption licensed image.
I've tried multiple times to no avail, I've also gone as far as installing the LDPE image of 7.0.116.0 thinking it needed that before downgrading but it still didn't work.
Any ideas / suggestions are appreciated.
Thanks!

Ryan,
You are correct, 7.0.116.0 is the first WLC image where we have the normal and then LDPE image available. The LDPE image is intended for countries that require special licensing for data payload encryption.
In order to comply with export laws, we do not allow units that have LDPE image installed to be converted to normal software -- I think this is the problem you are currently facing.
At this point you should go ahead and open up a TAC case to discuss your options in further detail. You can include a link to this thread in your problem description.
-Patrick Croak
Wireless TAC

Similar Messages

Upgrading a wlc 5508 from 7.0.116 to 7.4

Hi
I have a wlc 5508 running version 7.0.116.0 that I need to uppgrade to use the CAP2602I AP. I understand that I need to upgrade it to version 7.0.240 before 7.4.100 to avoid loosing HREAP VLAN mappings, and I have also read that i need to install the FUS image (http://www.cisco.com/en/US/docs/wireless/controller/release/notes/fus_rn_1_7_0_0.html). In what order should this be done? Shlod the FUS image be installed before new firmware ore after firmware or after 7.0.240 but before 7.4?
/Björn

It can be done before or after. I have always done the FUS upgrade after the image upgrade
Sent from Cisco Technical Support iPhone App

5508 WLC Upgrade from 7.0.116 to 7.2.111.3

I am planing to upgrade 2 of my 5508 series WLC from 7.0.116 to version 7.2.111.3. I understand that legacy AP's are no longer supported. Is there any other issues I should be aware of that others have experienced? Is the upgrade straight-forward just like other code upgrades? Thank you.

Thanks so much for all the information. Afterr reading throught this, it makes sense now. I do have one more question. After doing a show sysinfo on these controllers, it does look like the FUS does need to be updated. Should I perform this before I upgrade to version 7.2 code, or after I have peformed the upgrade to 7.2, or does it matter?
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.116.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS

How to Downgrade Rpd From 11g to 10g???

Hi all,
I want to know how to downgrade rpd from obiee 11.1.1.5 to obiee 10.1.3.4.
please share the valuable links.
Thanks.

First, you will have to completely uninstall 11g, see steps below:
http://obiee911.blogspot.com/2013/01/uninstalling-obiee-11g-instance-on.html
This should be followed by installing 10g, and then applying 10g patches to reach 10.1.3.4.1 version. I hope you have all the right 10g installation files available. Im not sure if you can download them from Oracle anymore, please check before proceeding.

How to downgrade catalog from obiee11.6 to 11.5?

hi:
Could any one tell me how to downgrade catalog from obiee11.6 to 11.5?

I'm afraid you don't.
Please award points if this was helpful/correct

HT4623 How to downgrade iPhone from ios6 to ios5 without jailbreaking?

How to downgrade iPhone from ios6 to ios5 without jailbreaking?
It is uncomfortable to use Appstore and uninformative Apple maps.
I regret, that I updated my iOS5, can I get it back?

Sadly, Apple is amazingly good at keeping users from downgrading an iPhone. For some reason, a prior update (5.1.1) bricked my 3GS, and that's how I learned the hard way how firmly Apple had control of the upgrade/downgrad process. I find that annoying, as well as the fact that Apple "pushes" (figureatively and literally) updates on users, many of whom simply update immediately, without realizing there could be a downside. I've been amazed at how many non-techy iPhone using friends have complained to me about maps, and they wish they had never updated to iOS 6.
Anyway, I'm still using iOS 5 on my iPhone 4S, as I just feel too attached to my good old Google-based Map app (and the web version of Google Maps is really very different than the App version -- I tried it, thinking I would finally update my iPhone, but was really dissatisfied with the web version). I do know iOS 6 is superior in many ways, but for now, I am just that attached to my good old Map app.

My iPod touch 4G will not work after I tried to Downgrade it from iOS 5 to iOS 6

My iPod touch 4G will not work after I tried to Downgrade it from iOS 5 to iOS 6. The screen is black and it doesn't work.

Downgrading the iOS is not supported by Apple.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Atleast give us downgrade option from belle to Ann...

atleast give us downgrade option from belle to Anna plz,because belle have numorous problems and it can be solved atleast in 2-3 months so give us a option to downgrade to anna plz be quick

its all a wish ful thinking my friend. Nokia will never give a rol back option otherwise belle will collapse. They dont want a fresh rolled product on which they have spent millions just on advertisement to go to ruins. So stop dreaming about that. Secondly nokia phone model particular fix will not be released for any model. Belle is going to be same for all. So dont waste your time. I wrote a huge letter and i even got a reply from nokia you can read it on my forum and from their tone you can clearly see they dont have any intentions to change.
/t5/Eseries-and-Communicators/NOKIA-MODERATORS-ONLY/td-p/1318965
Join my movement to bring a change in NOKIA for good by supporting my FORUM
http://discussions.europe.nokia.com/t5/Eseries-and-Communicators/NOKIA-MODERATORS-ONLY/td-p/1318965

HT4007 Downgraded OS from Mavericks to Mountain Lion, how to get Aperture to work on Mountain Lion?

Downgraded OS from Mavericks to Mountain Lion, how to get Aperture to work on Mountain Lion? My iMac (Intel) is older and Apple told me this model doesn't handle Mavericks well, recommended I step back to Mountain Lion, which was where Aperture was originally used. Aperture was upgraded when I installed Mavericks, need to go back to older version. How?

Erase disk drive
Restore backup made prior to upgrade
Allan

Downgrade Guide from Windows 7 to XP for HP Compaq 500B MT

Downgrade Guide from Windows 7 to XP for HP Compaq 500B MT,
the installation stop at: setup is starting windows
I have left it there for a weekend it does not pass that stage.
Thanks
Mo

Hi:
You have to load the applicable SATA AHCI or RAID driver either by slipstreaming them, or by using the F6 key and installing the driver from a USB floppy disk drive.
See this guide for how to slipstream the drivers. Read the intel section and then follow the instructions in the downloadable document to slipstream all of the drivers.
http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and-Software/SATA-drivers-for-XP-solution-on...

Wlc 5508 upgrade problem from 7.0.116.0 to 7.0.235.3

We have two WLC model 5508 with the follwing information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.116.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS + LDPE
System Name...................................... WLC-IDB-3
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.80.2.250
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... SA - Saudi Arabia
I tried to upgrde the software version to 7.0.230.0 or 7.0.235.3 but wlc displayed the following message
ERROR: Incompatible SW image.ERROR: Please install the Data Payload Encryption licensed image”
please i need the necessary steps to resolve the problem.
Regards ,

Hi,
This issue occurs because the Controller has an LDPE image installed, which is only needed in Russia where Data DTLS Payload Encryption is regulated by the Government. Cisco only recommends using this image if you reside in Russia. To resolve this issue and put the standard image on
To follow the steps go through the below link
http://sigkillit.com/tag/error-incompatible-sw-image-error-please-install-the-data-payload-encryption-licensed-image/

How to downgrade easily from windows 8.1 OEM to Windows 7 Pro

Hi,
I've tried to get used to Windows 8.1 (7 months), but I did not find a solution to get the classic view (3D look instead of the extra flat look) nor to play spider solitaire in a windowed mode, it always opens in full screen (desktop PC 2560x1440). If I
get the game in a small windows, it's a "crab view" = lateral.
I've created an account and when I went online the 1st time, Microsoft made it a MS account and I don't have my own account anymore. I don't feel that I own the PC, it doesn't feel like my personal PC. It feels like a public internet PC. I have no pleasure
at all using it.
I feel sad because I have been saving money for so long to buy a powerful PC with a nice large screen and it is so disappointing because of Windows 8.1 OEM. I have a license for Windows 7 Pro but if install it and it does not work (I can't find all the drivers),
the company I bought it from warns me I will lose my warranty.
It seems incredible to me that I have now 1st to pay Windows 8.1 Pro (I want to run away from it) in order to get downgrade rights. I feel miserable and helpless.
In the past I have bought a PC every time there was a new O/S (Windows 3.1, 95, 98, Millennium, Windows 2000, XP, XP Pro, Vista Home, Windows 7 Home.
Please any help is appreciated. I would like to be able to downgrade automatically, like when you click the "Windows update item in Start Menu" that everything happens automatically, but instead of upgrading I would like to downgrade.
Caroline

You can only do a clean install of Windows 7 to "downgrade" from Windows 8.1. There is no other path.
And you must ensure your hardware has support for Windows 7. Many of the platforms with Windows 8 do not have the necessary drivers to support the installation.
Follow Milos Puchta's advise and contact the manufacturer/vendor of your system for all assistance in this endeavor.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

Downgrade to from IOS6 to IOS 5.1

I need to downgrade my Ipod touch from IOS6 to IOS5.1.1 how can I do it. Just bought my Ipod 2 days ago. If not possible then I will return it

There is no legit way at all to downgrade.

Cisco WLC 5508 V 7.0.116.0 Help

I have a WLC 5508, that has been working with AIR LAP 1522 AG-E-K9 and AIR LAP 1142N E K9 access points. I have deployed two
AIR-CAP1552E-A-K9 AP's on the WLC. I had to upgrade to Version 7.0.116.0, and had to set the country code to US ( Was ZA). The good news is that on US country code the new 1552's works great.
My problem now is to get the existing 1522 and 1142 AP's to work in conjunction with the 1552's on US country code.
Any information would be greatly appreciated.
Thank You in advance.

George:
Multiple country codes are not supported for MESH APs.
You can only choose one country if you are using MESH APs whatever the model is.
If you have MESH APs with multiple country regulatories I think the only way to go is to replace your APs so all of them to be under same regulatory.
Features Not Supported on Mesh NetworksThese controller features are not supported on mesh networks:
Multi-country support
Load-based CAC (Mesh networks support only bandwidth-based, or static, CAC.)
High availability (fast heartbeat and primary discovery join timer)
EAP-FASTv1 and 802.1X authentication
EAP-FASTv1 and 802.1X authentication
Locally significant certificate
Location-based services
Reference: http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008072ea79.shtml
HTH
Amjad

Kernel panic during downgrade attempt from Lion to Snow Leopard

Hi guys,
I am experiencing two issues with Lion so I decided to downgrade to Snow Leopard using my Time Machine backup.
So I rebooted, held the option key down, booted from recovery disk, selected the option to select a time machine backup. I picked the latest 10.6.8 save.
Then, I waited for recovery... After completion, I noticed that I could not access my System Preferences anymore in SL. So I realised that I should have done the first steps using the option from the SL disk instead of the recovery disk.
I restarted with the SL disk in, tried to boot from the disk and got a scary kernel panic every time I tried (right when it tried to boot from the SL disk). I do not know what to do, I simply want to go back to SL backup (from my time machine) before Lion upgrade.
But, my only option to boot up is with a Lion DVD...
Any help would be greatly welecomed!
Thanks!

Just wanted to let you all know that I figured out why I was getting the kernel panic error: I was using an old SL upgrade DVD (the very first that was available in Apple stores when SL came out) instead of the install DVD that came with my iMac.
I just tried to boot from the right DVD and it worked fine. This thread can be marked as resolved.
Thanks!

Downgrading 5508 from 7.0.116.0 to 7.0.98.218

Similar Messages

Maybe you are looking for