Download CHUD Tools then massive power failure

HELP, PLEASE!!!
I've had my MACs for about 6 years now and never had any real problems. Recently however I noticed the G4 starting running quite hot and loud so I decided to use CHUD tools to cool it down a bit. I downloaded the app and ran the 'previous CHUD versions' checker as instructed. As soon as I clicked on it the machine shut down and I've been unable to restart since. (I don't think it actualy launched and I didn't get as far as installing the actual tools app)
The power light has a solid white light on when depressed, but goes no further. I've investigated the cause quite thoroughly and read all the forums about the G4 PSU failure,PRAM reset,battery changing,CPU reseting etc. I've done all of those and have the +5v trivkle on pin 1 of 24 of the PSU.
I've also tried a different hard drive in the machine - trying to ascertain whether it is the CHUD tools causing the problem (software/hardware problem?)and it still won't power up. Therefore I think that it's just a crazy coincidence that I launched CHUD and then had this failure as the 'non-CHUD infected' drive should have enabled the machine to launch I think.
So I'm wondering, I think it has to be either the PSU or power switch itself. I have the 5v trickle as mentioned, but are there further tests I can do on a 24 pin supply to confirm its status please?
If not, Is there a way of testing the power switch on the front of the machine please?
THANKS VERY MUCH IN ADVANCE FOR ANY HELP!
regards
Dan

Even if by 'PRAM reset' you mean use of the PMU switch, you may not have hit upon the single most useful first approach to an MDD that fails to start up: resetting the MLB.
Switch off mains power at the wall or power-board. Open the door and ground yourself on the internal metalwork, Remove the PRAM battery. Unplug the mains cable at the Mac end. (This is Apple's recommendation, but I don't follow it because Australian GPOs—power outlets—are universally grounded three-pin sockets. If your GPO tests as reliably grounded, as well as switched, you don't need to do so, either.)
Wait at least 10min. Replug the mains cable into the Mac (if you separated it above), but do not yet switch on mains power. Ground yourself again. Restore the PRAM battery only if it shows above 3.3V in circuit. Otherwise, replace it with a new battery. Wait 20sec. Press the PMU reset switch for 1sec once, and once only. If the switch bounces it will be interpreted by the PMU as two presses, with an entirely wrong outcome. The PMU is extremely sensitive to stray charge, so make sure that the hand that presses the button is also in contact with the metalwork of the door.
Close the door, switch on the mains supply and start up the Mac from the touch-sensitive 'button' on the ADC display. Given nothing worse than the Mac's former confusion as the cause of its failure, you should be up and away. If not, failure of your PSU is a distinct possibility.

Similar Messages

Massive Power Failure Powerbook G4 15"

Hello,
I was given a Powerbook G4 (15" 1.67ghz running on 10.4.11) by a friend who had not used it for about 6 months. The battery was not taken out during those 6 months so I expected trouble there. However, after charging it while it was switched off, it booted perfectly and ran smoothly. The problems started when I plugged in the ac adapter to charge it while running. As soon as it connected, it crashed; blue stripes and all. I have tried to charge it while it is turned on many times but it almost always crashes imediatly and sometimes stays on for a few seconds (and shows the batter connected icon) before crashes the excact same way. Also, although it charges the battery when switched-off and boots perfectly on the battery, once it is plugged in it won't come to live. It gives a little sigh and sometimes the fan goes on, but then goes silent. So I took out the battery and booted it on the ac adapter alone. It booted and worked for about an hour, and then crashed the same way. After that happened it also didn't boot from just the ac adaptor anymore.
I have tried the PMU and PRAM things, but they didn't do anything.
The adapter plug and the jack seem to be fine, they're not loose at all.
The battery specs are:
Full Charge 3637
Amperage -1488
Voltage 11387
Cycle Count 387
I guess the battery can be replaced but I wonder if that would solve the problem, knowing that it works fine on just the battery, but that it fails to boot while plugged in, or plugged in without battery. Anyone any ideas? Should I risk buying a new battery??
Your help is much appreciated!

There's only 4 major components in the charging circuit: power adapter, dc-in card, battery, and logic board. You've said the system runs fine on battery power, and charges OK when the system is off. So power adapter would seem to be OK and battery would seem to be OK (although that's a fair amount of cycles on it). You could try a new battery, but my money would be on an intermittent issue with the dc-in card or logic board. Unfortuanately, there is no test you can run, with the power circuit you replace parts, typically starting with the least expensive.

Ecently, i intended to download but unfortunately it's already more than 5 attempts. Due to the slow connection and power failure, my download failed to complete. Would it be possible to download the application again? Regards

Recently, i intended to download but unfortunately it's already more
than 5 attempts. Due to the slow connection and power failure, my
download failed to complete.
Would it be possible to download the application again?
Regards

Which application does this concern? Alternative downloads are available thru the following pages...
Download and Installation Help -
https://helpx.adobe.com/download-install.html
You can also download trial versions of software thru the site linked below and then use your current serial number to activate it.
Be sure to follow the steps outlined in the Note: Very Important Instructions section on the download pages at this site and have cookies enabled in your browser or else the download will not work properly.
http://prodesigntools.com/tag/ddl

What to do when Lion download stops because of power failure?

Please, can anybody advise: what to do when Mac OS X v10.7 Lion download stops, because of interruption of power supply?

I would first try reinstalling your backup copy of your previous OSX version if you can and then try reinitiating the installation of Lion from there. However, if that doesn't work at all, then the stoppage of the download by the power failure most likely corrupted your harddrive. I myself would then take the safest course and reformat the harddrive by booting from your Original Installation Disks and reformatting the harddrive from the Disk's "Disk Utility". Then go thru the installation of the previous operating system to the point where you can once again proceed with the download and installation of Lion.
Hope this helps
Message was edited by: Radiation Mac

Power failure then iPhoto library= POOF! :-( PLEASE HELP!

Power failure then iPhoto> library= POOF!
We had a power failure and of course iPhoto was open when my computer was improperly shut down. After powering up, I did the following; repaired permissions and ran disk utility (no problems found).
Upon opening iPhoto (6.03) I got the rebuild thumbnails message, and I said cancel (I was going to do it later), then IPhoto opened and it was BLANK! all 5000+ images were GONE! I am assuming the library got corrupted somehow on either the bad crash, or the canceling of the rebuild option.
Now, I am a bit neurotic about my pics, so I choose to make my own finder folders of pic when I take them off the camera, and then import into iPhoto that way. So the good news is I still have all my original pictures in folders in the finder.
From reading various threads here, and Googleing + Macfixit, etc etc. This is what I have done to try to recover my library. (not necessarily in this order)
[list]
[*]Trash/recreate the iPhoto plist preferences
[*]Clear caches using Cocktail software
[*]Repaired permissions (in Disk utility), and then repair iPhoto library folder permissions usuing instructions found here using Batchmod software
[*]Rebuild the iPhoto library (option, command) and selecting the 3 proper checkboxes.
[*]Ran iPhoto Library Manager software to rebuild the database with no success. I get the error message "This Library cannot be rebuilt because its XML file contains no data".
[*]Updated to iPhoto 6.04/repaired permissions and disk utility.
[/list]
Each time iPhoto loads completely blank and void of my photos!
My assumption is the XML file is corrupt since I am getting that message in iPhoto Library Manager.
So what to do? And hear are my questions /issues.
I would certainly like to preserve my 4 years of customization of keywords, titles , folders, smart folders, etc. (which I assume is held in the now corrupt XML file?).
What is the best way to recover my customization and most importantly the images!
I realize I can just re-import all my images from my original finder image folders that I have, but I assume this method will not recover my keywords ,etc?
Is there a way to recover my customization?
I do have a fairly recent backup of my iPhoto folder on a backup drive ( I think!) It does not have all my newer pics in it, but as I mentioned I do still have all my .jpgs, just not in iPhoto!
Thanks in advance for reading and any help offered!
PBG4 1.33 2gig Mac OS X (10.4.6) 120 gig hd

I got all my pictures AND everything else back, folders, ratings, keywords etc
Fortunately I had a backup of the entire iPhoto library folder, it was about 3 months old (I know shame on me) so I didn't want to just use the entire backup folder and lose 3 months of photos.
So I just copied the AlbumData.xml file and the Library6.iPhoto file. PRESTO all my pictures were back WITH all the folders,keywords etc, etc intact!! (up till the 3 month old backup point).
Then I just re-imported the missing 3 months worth of pictures from the original folder in the iphoto library folder. So all I had to recreate was 3 months worth of customization. WHEW!!
Reading through the discussions it seems there is a fair number of users where iPhoto would go empty, but they knew the images were still on the computer. I am not a programmer, but it seems silly to me the their are files that get re-written everytime iPhoto closes....computers crash. and then what happens to the files? Mine got corrupted, lesson learned BACKUP more frequently!!
Thanks to Old Toad who steered me to the Library6.iPhoto as a possible troublemaker in another thread!

We recently had a few brief power failures. Since then, my Mac Pro has been very slow on start up. Any suggestions?

We Recently had a few brief power failures. Since then, my Mac Pro has been very slow on startup. Any suggestions?

Like the man says:
Run Disk Utility > Repair ... (not just repair permissions) while booted from another drive. If you have a stronger utility like Disk Warrior, that would be even better.
If you find that the ONLY way you can do this is by booting from the DVD, The Hatter recommends you establish an emergency drive or partition on a drive other than the Boot drive and use that in the future. It makes emergency Repair, backup, and cloning much easier.

I started Boot Camp on a MAC mini but then had a power failure after 30 secs :( Now when I start Boot Camp the option to install Windows 7 is gone. In it's place is Remove Windows 7. It seems to hang at Partitioning disk Can I recover?

I started Boot Camp on a MAC mini but then had a power failure after 30 secs Now when I start Boot Camp the option to install Windows 7 is gone. In it's place is Remove Windows 7. It seems to hang at Partitioning disk How can I recover?

Welcome to the Apple Support Communities
That's because the Boot Camp volume was created, but your Mac hasn't been set up to start automatically from the Windows disc. Insert the Windows DVD and press C key while your Mac is starting to start Windows installation.
If you want to make sure that everything is correct, open Boot Camp Assistant and choose the option to remove Windows 7. Then, open that application again, select the option to install Windows 7 and you will be able to install Windows as usual

I'm trying to update the latest version of iTunes but my computer gives me an error saying to go to tools then download only and update manually. What do I do?

I'm trying to update the latest version of iTunes but my computer gives me an error saying to go to tools then download only and update manually. What do I do?

Try updating using an iTunesSetup.exe (or iTunes64Setup.exe) installer file downloaded from the Apple website:
http://www.apple.com/itunes/download/

After a power failure, all the messages (or what appears to be all of then, 5K+) were in the inbox marked unread and all the folders were gone. HELP!!!

A long power failure shut down my wife's system without shutting down Windows. When she started it, all her email messages were in her Inbox and marked unread. She previously had 25 or 30 folders; they're all gone. This is an IMAP account synced with Gmail. When I looked at the profile folder with Windows Explorer, only a few of the folder files (including .MSF) were there; the rest of the folders were listed as files, not folders (both the no-extension and .MSF files for each). Oddly enough, all the folders seem to be in the POP3 folder, but it isn't a POP3 account. This is a major major problem. Please help me solve it.

Thank you for such a prompt reply, Matt. I don't think that would work (although I'm not sure) because the folders don't exist on the Gmail server, just on her computer (and our backup hard drive). We use Gmail so we can get our mail when we're traveling, but don't store any messages there. We save them in folders on our home systems and delete them from the Gmail server. I hope against hope that there is some way I can recover her folders; she's really upset by this, email is mostly what she uses the system for to keep in contact with our children and her siblings. I'm going to copy the entire profile folder to a thumb drive because the backup software will overwrite the current files on the backup hard drive at 0300 tomorrow. It sounds like I'm not likely to find a simple solution to this, but I hope those with more (much more) knowledge than I possess can show me that I'm wrong and it can be solved.

AOL Install Fix using CHUD Tools

Hello,
For those of you who were asking about how to fix the AOL install problem on Intel Macs, here is a tip I found at macosxhints.com:
AOL seems to have a problem installing on multi-core Intel Macs. The installation hangs at "Installing Main Database." I found a successful workaround for this problem. Go to Apple's developer website and download the CHUD Tools. Once installed, there will be a Processor preference pane in System Preferences. Use this to turn off all but one Intel processor, then run the AOL installer. Once the installer finishes, turn the processors back on. Disabling CPUs solved install issues with other apps.
JLM

Holy cow, what a piece of junk installer. SERIOUSLY?!?! The AOL engineers never in their lives tested their application on a multi-CPU machine?
Seriously. How would anyone trust something so junky to their machine.

IMovie video project I made has no audio working after power failure

I have spent about a week stitching together family movies by ripping them to Apple tv format, then use a software program called MPEG streamclip to create a DV version which take about 24 gb a piece, I put 12 hours worth into iMovie which has taken a ton of space etc. So I created a project and am now about 1h 35 min in and this is getting small 3-5 clips of my son who is 7 months and my wife and myself b/c were going to England on Friday so I was created a nice movie for my new in laws and family I am meeting for the first time. So I had a saved file and iMovie was open and I had a power failure. I opened iMovie freaking out and then saw all the footage and the project still there so I was extremely thankful b/c of the 7 dvds I created due to space limitation once I imported I deleted the original (i have the original dvd but it takes about 6 hours to take from DVD to Apple TV format, then about 2 hours to export to DV and then another 1 hour to import into iMovie so each dvd took a full day for me due to work etc)
Anyway whats now happened is there is no audio on either the project or the original footage that has been imported, again about 12 hours of footage and a project thats 1 hr 35 mins. Whats strange is all other projects and imported video the sound and video works perfect. THis is the only one and of course its the most important one. ANY SUGGESTIONS WILL BE APPRECIATED.
If needed I will start over and do as much as I can but of course I am praying there is a simple solution.
Thanks.
newest iMovie, newest OSX etc if that helps

Thought you could use this info about getting FireWire to work!
First, you should always Repair Permissions in Disk Utility before and after any update; I would do that now. If you installed your update with FireWire plugged in, your Mac may not recognize it anymore.
Try resetting your FireWire ports by disconnecting all FW devices, shut down your Mac and unplug it from AC power (wall socket) for 30 minutes. plug it back in and try FW.
If that did'nt work, first run the Disk Repair as shown in Apple doc.#106214 before the next step. Then, download the combo update from this site (yours may be corrupt), not Software Update, disconnect all firewire + USB devices except keyboard + mouse, Repair Permissions, re-install update, Repair Permissions again + try. Yours is the 10.4.10 Combo update ( PPC, not for Intel systems). Others reading, download the Combo that applies to your system.
If that still did'nt get it Zap the PRAM. While restarting Mac hold down the following key combo Command-Option-P-R. Keep holding those keys down till you hear the second start-up chime, then release.
For those of you with Macs that are not PowerBooks or iBooks, a bad internal battery can cause FireWire to not be recognized, so make sure it's good! Also, here is Apple doc.#88338 on getting FireWire to work.
Cheers!
DALE

Cannot Start EPM Architect Process Manager after a Power Failure

Hey All,
We had a power failure in the office last night/this morning. We have two environments, and luckily, our production environment seems to be working OK, however, on our development environment, we cannot get the EPM Architect Process Manager to start (or any of the associated services).
Here is what we have tried already:
- Restarting the server
- Restarting all services in the correct order
- Running EPM System Configurator for Performance Management Architect > Configure Database (the first time, we just re-used the same tables, and had the same error. We did it a second time and dropped the tables and were able to get the service (and all other EPMA services) to start, but we couldn't get into the Application or Dimension Library.
- Restoring the EPMA DB schema from backup from two nights ago - same error when trying to restart the service.
We are running 11.1.1.3 (04 patches for Planning and CalcManager, but not EPMA). We are running MS SQL 2005 for the relational databases.
Error message when restarting the service:
"The Hyperion EPM Architect - Process Manager service on Local Computer started and then stopped. Some services stop automatically..."
When we go to the event viewer, it tells us:
Service cannot be started. Hyperion.DimensionServer.ProcessManager.Interface.ProcessManagerException: Dimension Server started but failed to initialize on machine CSHMISHYPTST. Check the error log on that machine.
at Hyperion.DimensionServer.ProcessManager.EngineManager.StartEngine(Machine machine, EngineType engineType)
at Hyperion.DimensionServer.ProcessManager.EngineManager.InitializeReadWriteEngine()
at Hyperion.DimensionServer.ProcessManager.EngineManager.Load()
at Hyperion.DimensionServer.ProcessManager.ProcessManager.Initialize()
at Hyperion.DimensionServer.ProcessManager.Service.OnStart(String[] args)
at System.ServiceProcess.ServiceBase.ServiceQueuedMainCallback(Object state)
Went into D:\Hyperion\logs\epma and looked at the "dimension_server.log":
2010-09-21 12:45:08,939 [Engine Startup] Hyperion.DimensionServer.Program.LogMessage(:0) - An error occurred during initialization of engine ID 1: Object reference not set to an instance of an object..
System.NullReferenceException: Object reference not set to an instance of an object.
at Hyperion.DimensionServer.RelationshipMemberList.Add(RelationshipMember item)
at Hyperion.DimensionServer.Dimension.<LoadSharedMembers>b__11(RelationshipRecord relationship)
at Hyperion.DataAccessLayerCore.DALRowset`1.Read()
at Hyperion.DataAccessLayerCore.SelectCommand`1.Execute(Action`1 callback)
at Hyperion.DataAccessLayerCore.GenericDAO.Select[T](Action`1 callback, SetParamsEvent`1 onSetParams)
at Hyperion.DimensionServer.DAO.DimensionDAO.LoadRelationships(Int32 libraryID, Int32 dimensionID, Boolean primary, Action`1 action)
at Hyperion.DimensionServer.DAO.DimensionDAO.LoadSharedMembers(Int32 libraryID, Int32 dimensionID, Action`1 action)
at Hyperion.DimensionServer.Dimension.LoadSharedMembers()
at Hyperion.DimensionServer.Dimension.LoadMembers()
at Hyperion.DimensionServer.Library.Load()
at Hyperion.DimensionServer.Global.Initialize(String jobManagerConnectString)
at Hyperion.DimensionServer.Program.Main(String[] args)
Looking for some suggestions or ideas. Have tried searching the forums and Google, but haven't had any success.

Ironically I just got alerted by Oracle that EPMA patch 03 had been pulled from the MOS site and replaced by patch 04.
You are receiving this notification because our records indicate that you have downloaded Oracle Hyperion Enterprise Performance Management Architect 11.1.1.3.03 Service Fix – Patch 9650100.
Please be advised that Oracle Hyperion Enterprise Performance Management Architect 11.1.1.3.03 Service Fix - Patch 9650100 has been removed from My Oracle Support and is superseded by Oracle Hyperion Enterprise Performance Management Architect 11.1.1.3.04 Service Pack – Patch 9800827.
Patch 9650100 is now obsolete and you should use Oracle Hyperion Enterprise Performance Management Architect 11.1.1.3.04 Service Pack - Patch 9800827, which corrects file packaging issues, from My Oracle Support (https://support.oracle.com) instead.
Please thoroughly review the Readme for Oracle Hyperion Enterprise Performance Management Architect 11.1.1.3.04 Service Pack - Patch 9800827 prior to implementing.
Best regards,
Chris

Power failure for my camera OV8830

Hello, I have a tablet elite pad 900 but i have a problem for the camera. the error is error 10 the device cannot start, STATUS DEVICE POWER FAILURE.someone can please give a solution for this problembest regards

Hey ,
Welcome to the HP forums. I understand you're getting "error 10" on your rear camera in Device Manager. It's important to start by stating the drivers for integrated image capture devices are included in the Windows operating system and are not available for independent download, which can make things tricky. Here's the steps I would personally take, in this order: Make sure your Windows operating system is up to date.Reinstall the camera. (Right click and uninstall in Device Manager and then restart the tablet.)System restore to when the camera worked.Back up and perform a system recovery.If none of that works please visit http://h22207.www2.hp.com/contact-hp/. After selecting your region click the Contact Support tab near the top and fill out your product info. Once you've entered the product there is a form to fill out at the bottom of the page. When you've submitted the form it will provide you with a case number and phone number to call. Thanks.

Power Failure: cpu=1; code=00000008 (unaligned stack)

I have a Quicksilver 2002 DP 1.0GHz.
System Profiler reads it as a DP 733GHz about 50% of the time and a DP 1.0GHz the other 50%.
It always has a screen freeze about 4-5 min after startup.
I reset the processors; nothing changed.
But now I'm getting some system failures at bootup:
Power Failure: cpu=1; code=00000008 (unaligned stack)
and something about waiting for the debugger.
Anyone have an idea where the is?
Thanks,
Shamus

Yesterday my computer blacked out, like the circuit had blown but no. I put my hard drive into another G4, Dual 1.25 Mirror. It's a 120 G drive, running 10.4, current Safari. I ran Tech Tools and Disk Warrior and everything seems fine with it. But as I tried to lauch iTunes, it acts as though I’m loading a new version, asking me to accept the terms of the software. I canceled. Wierd. I purchased and downloaded an audio book from Audible yesterday and synced my ipod which received it. In iTunes info it gives that time as when iTunes was changed. It's wierd enough to wonder about a bug. Otherwise this hard drive acts fine.
Any ideas? Much appreciated. The original computer that I'd like to fix is still blacked-out although as long as I hold the button, it lights. I zapped the PRam but have no other ideas. Thanks for any ideas.

G5 Power failure during start up and wake

I have an early G5 20" non-iSight iMac that has a power problem that is steadily getting worse.
As Apple support has expired and can't be extended, I'm at a loss how to resolve this.
Description.
The problem first started as intermittent during wake up from sleep (power light pulsing). I'd move the mouse or tap the keyboard to wake the iMac and I'd hear the disk just start to spin up followed by a sharp 'pop/click' like the power cord had been pulled, and it would be powered off needing the power button to be pressed to restart from scratch.
Now the problem has worsened in that occasionally I will find the iMac has completely powered down during sleep. When I restart it can take up to 6 or more attempts to get to the point where I can use it. There's a sequence of restarts needed, each starting from pushing the power button, and then ending during the starting sequence with a 'pop/click' as the power suddenly shuts off. Each time the start up will progress a little further than the previous attempt until eventually it finishes building the desk top after login and I can operate normally until the next time I find it powered off after a few hours of non-use. The power failure starts initially from just after the welcome chime, and progresses to maybe 5 or 6 times later to during the desk top build after log-in. However, once logged in and operating the iMac behaves as normal, switching users, log-out and login, screen save and wake from screen save etc are all as I'd expect. I've not (yet at least) had any sudden power failures during normal operation.
The serial number of the iMac falls within the Sept 05 Repair Extension Program serial number range (not EMC 2056 though), but when I spoke to Apple Support they said that the lack of random behaviour meant that the problem I'm having is not related and so would not be covered by this program.
So I'm kinda stuck with a problem that is annoying when it occurs, which is daily at the moment, although it's been this bad a few weeks back and then was fine (iMac left switched on for 2 to 3 weeks without a problem) until we had a power cut earlier this week, and it's started again.
I've searched through the forums and while I could find plenty of references to 'Sudden Power Loss' none seemed to be as predictable and similar to this one.
Suggestions and ideas welcome. Thanks.

i am having a similiar issue. I have the same exact computer (iMac G5, non-isight) and it stays on for 30 mins, hour, 3 hours and shuts off. Upon starting up, sometimes it doesn't make it to the login screen before shutting down again. I have downloaded heat temp monitor programs and it seems to get to about 70 degrees celcius sometimes. Upon restarting, I get the "report problem to apple" screen with this information. I have tried to restart the power supply too.
Thu Apr 17 09:02:18 2008
panic(cpu 0 caller 0x008E0BE4): "Missing CPU diode calibration information.\n"@/SourceCache/IOPlatformPluginFamily/IOPlatformPluginFamily-312. 0.1/SMUNeo2_PlatformPlugin/SMU_Neo2CPUTempSensor.cpp:124
Latest stack backtrace for cpu 0:
Backtrace:
0x0009B478 0x0009BE1C 0x00029DD4 0x008E0BE4 0x008D0308 0x008CFD78 0x008E309C 0x008D48E8
0x008E2C6C 0x00342B8C 0x00343CE0 0x00345B90 0x00344CB0 0x000B05D4
Kernel loadable modules in backtrace (with dependencies):
com.apple.driver.SMUNeo2PlatformPlugin(3.1.2d1)@0x8dc000->0x8eafff
dependency: com.apple.driver.IOPlatformPluginFamily(3.1.2d1)@0x8c9000
com.apple.driver.IOPlatformPluginFamily(3.1.2d1)@0x8c9000->0x8dbfff
Proceeding back via exception chain:
Exception state (sv=0x39e04c80)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
BSD process name corresponding to current thread: kernel_task
Mac OS version:
9C7010
Kernel version:
Darwin Kernel Version 9.2.2: Tue Mar 4 21:23:43 PST 2008; root:xnu-1228.4.31~1/RELEASE_PPC
System model name: PowerMac8,1
*>}

Download CHUD Tools then massive power failure

Similar Messages

Maybe you are looking for