Download devices syslogs of Cisco Prime Infrastructure 2.2

Hello,
I'm working with Cisco Prime Infrastructure 2.2, wish I could download to my PC syslog captured by PI.

Hi ,
In the prime infrastructure Syslogs are directly read from udp port 514 and then filtered , the non SEV1 and SEV2 syslogs will be dropped and will not be entered into db . The syslog messages will not be saved into log files .
Thanks-
Afroz
***Ratings Encourages Contributors ****

Similar Messages

Is cisco prime infrastructure support / can be run as syslog server?

Dear All,
is cisco prime infrastructure support / can be run as syslog server?
and,
where i can see network topology diagram, using cisco prime infrastructure?
many thanks,
Jerri

Hello. Cisco Prime LMS will be replaced by Cisco Prime Infrastructure in the near future.
In the current release of Cisco Prime Infrastructure you can't use topology diagrams. This feature is in roadmap.
About syslog, you can send syslogs to Cisco Prime Infrastructure, but I don't recommend using it as syslog server. Please see this link for more information https://supportforums.cisco.com/thread/2179520
Please rate if this helps

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1

Hi, I'm working on implementing the Cisco Prime Infrastructure 2.1 and want to display the syslog about ASA5512-X with Software Version 9.2.
What would be the procedure for configuring?
Thanks in advance.

Hi,
Enable "logging host x.x.x.x " command to enable logging
check the below link:
http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/monitor_syslog.html#68764
FYI: Prime Infrastructure support only SEV 0,1,2 syslogs as of now.
Operate > alarm and events > syslogs
Thanks-
Afroz
****Ratings Encourages Contributors *****

Cisco Prime Infrastructure - I can't see the hardware virtual image when I selected a device managed by Prime Infrastructure. See attached picture

My Cisco Prime Infrastructure ver. 1.2.1.12
Cisco Prime Infrastructure - I can't see the hardware virtual image when I selected a device managed by Prime Infrastructure. See attached picture.
Please let me know how to access or enable the feature.
Thanks,
Tek

This is by no means a full solution, but deleting and re-adding only takes a few minutes if you use the "Export Device" and "Bulk Import" features from the Device Work Center. You can export the desired devices to a CSV file, delete them, then import from the CSV.
Of course, you might lose historical data when deleting the devices, but I'm guessing that's not as relevant since the devices themselves have been replaced by different hardware.

Cisco nexus 6001 not a supported device on cisco prime infrastructure 2.1?

I have installed Cisco Prime Infrastructure 2.2 and Prime Infrastructure still doesn't seem to support the Nexus 6001 platform? Can someone tell me if Cisco Prime Infrastructure will ever support the Cisco Nexus 6001 platform or is there any plans to support it in any future device packs?

The Nexus 6001 isn't currently supported in PI 2.1. There's no workaround except to wait for a device or product update that adds support. Right now I know the 9000 series is on the 2.2 roadmap but I haven't seen any reference to the 6001 and PI.
Interestingly, Prime LMS does support both the 6001 and 6004. Reference.

Cisco Prime Infrastructure 2.0 -- Third Party Devices

Hello,
we are using cisco prime infrastructure 2.0. Is it possible to manage third party devices? (We have a lot of Enterasys Switches)
When i want to Archive the config of the device there is an error --> No Device Package found for the specific device.
It is necessary to install device packages for third party devices? Where can i find and install these packages?
Thx in advance

it seems not to be on the road-map according to the functional /feature comparison between LMS and PI 2.0:
http://www.cisco.com/en/US/partner/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html
...and I doubt it will come (quickly) because config management has a lot of pitfalls and Cisco has a lot to do to get around all of them with their own devices..
However, Inventory Management for third party devices is on the road-map
older version of the document (feature comparison PI 1.2 - LMS 4.2) can be found here:
http://www.cisco.com/en/US/partner/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/app_note_c27-716230.html

Device Reachable but Unmanaged in Cisco Prime Infrastructure 1.3

Hi,
I am running the Eval version of cisco Prime Infrastructure 1.3
I tried running discovery for WLC and it worked fine where all the controllers were discovered.
But when i try to discover a Switch, the reachability tab says Reachable but in Collection Status tab it shows Unmanaged.
When i click on the Unmanaged tab it says " Pre-collection check failed because: "
I have configured the SNMP correctly.
Does anyone know why is this happening.
All the help is greatly appreciated.

Had the same issue and noticed that the licence count for 100 devices (Eval Limit) was consumed as soon as we added the WLC
On your page https:///webacs/welcomeAction.do#pageId=LicenseCenter_pageId look at how many are taken and if it is in violation.
We added our 500 pak upgraded, and it still didn't fix the issue when re-syncing. We had to remove the device and re-add.
This is now resolved for us.

Cisco Prime Infrastructure - not updating device details

We run Cisco prime Infrastructure and I have found an interesting problem that I can't see an easy way round.
If I have say a Cisco 2950 switch on my network, managed by Prime and I upgrade it to a 3560 - I then ask Prime to re-sync the device details.
This works - you can see the updated configuration files etc but the device ID stays the same - Prime still thinks it is a 3560, which it was when the device was originally added.
Is there a way, short of deleting the device and adding it again (losing the config archive) of getting prime to update it's details to reflect the hardware change?
It came to light as it screwed up a network hardware audit I was doing - this is all showing up on Prime as the old 2050's which I have replaced with 3560's.
There must be an easier way that just deleting the device and re-adding it?

This is by no means a full solution, but deleting and re-adding only takes a few minutes if you use the "Export Device" and "Bulk Import" features from the Device Work Center. You can export the desired devices to a CSV file, delete them, then import from the CSV.
Of course, you might lose historical data when deleting the devices, but I'm guessing that's not as relevant since the devices themselves have been replaced by different hardware.

Cisco Prime infrastructure template undeploy

Hi,
I am new to cisco prime, I have create the new Trap receiver template and deployed to one of the wireless controller and saved the deployment
Now I want to undeploy the templates, When I tried undeploying the templates for same wireless controller, I got the warning message stating "Failed to undeploy the template"
Please advice on below points
1. How to undeploy the templates in cisco prime infrastructure
2. Where to find the snmp traps ( steps to check the snmp traps) in cisco prime.
Please Help!!!!!

Using System Logs
Prime Infrastructure logs all error, informational, and trace messages generated by all devices that are managed by Prime Infrastructure.
Prime Infrastructure also logs all SNMP messages and Syslogs it receives.
You can download and email the logs to use for troubleshooting Prime Infrastructure.
Step 1 Choose Administration > Logging. The General Logging Options Screen appears.
Step 2 Choose a Message Level.
Step 3 Check the check boxes within the Enable Log Module option to enable various administration modules. Check the Log Modules option to select all modules.
Step 4 In the Log File Settings portion, enter the following settings. These settings will be effective after restarting Prime Infrastructure.
Note The log file prefix can include the characters "%g" to sequentially number of files.
Step 5 Click the Download button to download the log file to your local machine.
Note The logs.zip filename includes a prefix with the host name, date, and time so that you can easily identify the stored log file. Included in the zip file is an html file that documents the log files.
Step 6 Enter the Email ID or Email IDs separated by commas to send the log file.
Note To send the log file in a mail you must have Email Server Configured.
Step 7 Click Submit.

Cisco Prime Infrastructure 2.0 and Cisco ASA

Hello,
We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
ASA version is 5505, image is 9.1(2).
So, I have a question: is it possible to manage ASAs with PI 2.0?
UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.

Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location.

UPS monitoring support with Cisco Prime Infrastructure 1.2

Dear Members,
Good day,
I am having a project implemented wherein i have the UPS power redudancy solution for our network devices.
Now can anyone gide that is it possible for below :-
UPS units installed with SNMP cards be monitored via Cisco Prime Infrastructure 1.2 as our monitoring & management solution is Cisco Prime Infrastructure 1.2 ?
if yes
Can you guide if following action would be possible to export the below logs from UPS unit to our Cisco Prime Infrastructure 1.2
   a) UPS fault status information
   b) UPS operational status(input power available Y/N)
   c) Battery fault status
   d) Battery charging current
   e) Battery charge level
   f) Output current
Conclusion is we need to confirm that would it be posible to achieve remote monitoring of these UPS units via our CPI 1.2
Thanks in Advance for your support & replies to this query.
Regards,
Muzammil N.

Prime Infrastructure 1.2 can manage non-Cisco devices in a limited fashion via SNMP query and trap processing. It cannot import logs and does not have a generic syslog server,
So if your devices have snmp read only support and can generate SNMP traps for the above you can add them to PI. Follow the manual add device procedure here.

Consultations on Cisco Prime Infrastructure 2.2

I recently installed Cisco Prime Infrastructure 2.2 and I have 2 questions regarding configuration:
1. What configurations should run for vulnerability when some event occurs on a switch an alarm is lifted in the Cisco Prime Infrastructure 2.2?
2. Is there any way to put a device into maintenance mode in the web interface of Cisco Prime Infrastructure 2.2, so that can not be spoiled reports regarding equipment availability during the execution of maintenance?

1. If you configure PI as an SNMP and syslog server for your devices and have enabled logging traps etc., PI's alarm browser will show the alarms. If you want them to be sent to you via email, you can do that under the Admin menu for setting up your Mail server and clicking the link to "Configure email notification for individual alarm categories." (see below - open in new tab to zoom). It's not completely customizable but what you see there is the current product capabilities in that regard.
2. No, this is not currently an available feature in PI 2.2.

Cisco Prime Infrastructure 2.1 Inventory Job

My cisco prime infrastructure performs a switch inventory job every night at 22:00 hrs. When I looked at the syslog of the devices in the inventory, I see some entries that I never saw with other LMS versions.
2014-06-30 22:00:01   Local7.Notice   xxx.xxx.xxx.xxx   5410: Jun 30 22:00:00.623 CST: %SYS-5-CONFIG_I: Configured from xxx.xxx.xxx.xxx by snmp
2014-06-30 22:00:01   Local7.Notice   xxx.xxx.xxx.xxx   5411: Jun 30 22:00:01.567 CST: %SYS-5-CONFIG_I: Configured from console by vty1 (xxx.xxx.xxx.xxx)
2014-06-30 22:05:10   Local7.Notice   xxx.xxx.xxx.xxx   5412: Jun 30 22:05:09.008 CST: %SYS-5-CONFIG_I: Configured from console by vty0 (xxx.xxx.xxx.xxx)
I don't understand what the PI is doing with the switches. Does anyone know what is happening during this inventory background job? TIA

Hello all,
we have the same problem maybe; Cisco Prime IF 2.1 is changing the running-configs and produces out-of-syncs ;
it turns so for us is, as if Cisco Prime IF 2.1 a snmp-server host x.x.x.x community entry writes in the running-config,
so are running-and startup-config are out-of-sync; is this correct? Herbert

Cisco Prime infrastructure Change severity Switches and hubs - link down alarm

Hi, I want to change the severity of the link down alarm in the Cisco Prime Infrastructure 1.3, but in the menu Administration -> System Settings -> Severity Configuration i can not find the alarm. Some body knows where is it? o where i can change the severity of that alarm?
Thanks in advanced.

Hi Rollin and Daniel,
the first test i did changing the severity was with a new installation, with no devices added and it worked, when i did it in a Prime infrastructure with devices added it didn´t work, well, for this Prime with devices i upgraded it with the patch for 1.3 version and now it works too, the alarms is ok as the alarm severity, this is the link for the patch:
http://software.cisco.com/download/release.html?mdfid=284652876&flowid=38562&softwareid=284272933&release=1.3.0&relind=AVAILABLE&rellifecycle=&reltype=all
i hope this helps,
Regards,
Milton Tizoc.

Download devices syslogs of Cisco Prime Infrastructure 2.2

Similar Messages

Maybe you are looking for