Download speeds dead in Mavericks!

I'm completely confused. I have a 12Mb internet connections that works great. I've upgraded my Mac Mini, MBP, and MB Air to Mavericks. Since then, my download speeds have gone from over 1MB/sec to about 50-60kb/sec. Doesn't matter if it's from the iTunes Store, a random website, or my web FTP servers.
I can't figure out what in Mavericks could possibly have caused this. I went to speedtest.net to make sure it wasn't my connection, but I get the 12-15Mb speeds through that test. To be sure, I've rebooted my modem and gone through all those normal steps. It is definitely NOT my internet connection. It's something about the Mavericks install.
Anyone else have this happen? Any thoughts as to what I can do to fix it?

I have this problem too and only since upgrading to Mavericks.
I'm downloading an Adobe program and it's averaging about 50-500 kbps. For a while, it sat at 199 for the better part of an hour. It occassionally goes up to 1.5 mbps...but only for a few moments before dropping to the 50-150 kbps range.
I've checked speedtest.net and it shows my speed ranging between 5-10 mbps depending on the time of day. The same results show on my iPhone using the OpenSignal app.
I changed by wireless wire channel over to 1 from 11 and that improved a bit, but not much.
I also pulled out my 4 year old Sony Viao and started downloading the same file. It's processing speed and RAM is glacial compared to my new iMac (just bought it 4 weeks ago). While Windows doesn't display the actual download speed that I can find, the progress showed it would beat my iMac. (The iMac has been downloading for over an hour and only at about 60%....the Sony Viao was at about 20% in 5 minutes.)
I'm with you Jeremy....is there a solution to this issue?

Similar Messages

My Macbook pro early 2012 maverick OS 10.9.5, slow download speed

My Macbook pro early 2012, has a difficult with download speed, I have 5mbps and the speed I m having its almost 1mbps, the issue its with the wifi and also the ethernet, what could be the cause of this, my upload speed is normal, the issue its only with the download, my other devices such as iphone, ipad, windows PC, android phone, work fine.

Can’t Connect to the Internet
Can’t Connect to the Internet (2)
Connect to the Internet
Connect to the Internet – Solutions and Troubleshooting
Connecting to the Internet - Solve Problems

G580 - pathetic download speed & wifi connectivity

I had purchased G580 laptop in October & upgraded to windows 8. Since then, the wifi problem has been regular. After updating the drivers the wifi is mostly. Once in a while I have to restart the router.. That's still OK, but the download speed is really pathetic.
I have another old Acer Laptop with windows 8 (upgraded) too. I have an 8 MBPS broadband connection. The Acer laptop has 1 Mbps download speed without any hindrance. But, the Lenovo G580 is giving 250kbps downloads, that too with regular stoppages. Another big issue - while.. this dead slow download happens, not even a single webpage opens.. Regular "error loading" messages.
Kindly help in rectifying the issue as I have updated all the drivers through windows update as well as lenovo site.
I'm using a bitdefender antivirus, will that have any problem with wifi speed ??
Kindly advice as the only other option is to discard the laptop.
thx
Satish

hi satishrk1978,
If you have the Atheros AR9285 Wireless Adapter, you can try to:
1. Update your wireless card driver to v10.0.0.221, get it here, otherwise skip this step.
2. Depending on your brand of router (and if applicable), make sure you disable WMM QoS (Wireless Multimedia) and WPS (Wi-Fi Protected Setup)
3. Use a WPA2-PSK TKIP or AES encryption.
4. If you have a dual band router (2.4Ghz and 5Ghz), try to use only the 2.4Ghz band.
5. Temporarily disable any running firewall / antivirus software.
5. After applying steps 1-5, try running a speedtest again via www.speedtest.net.
Let me know the result.
Cheers
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

My Macbook pro 2014 downloading speed is slow

Hello guys, I need help! I am new to Macbook, I was checking the internet speed on speedtest.net and my download speed was 11mbps. when I tried to download a movie it's actually 33-100kbps. I don't know if the movie website is slow or my macbook is slow. Any suggestions?
My macbook is 13' with retina display 2014
8gb 1600 MHz DDR3
intel core i5 2.6 GHz

Sounds as if the servers on the movie site are simply overloaded. It happens.
Clinton
MacBook Pro (15-inch Late 2011), OS X Mavericks 10.9.5, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display

Download speed lower than Dial Up

I am stumped. I am getting download speeds of 40 kbs or less from a plan that is 3355/751. Im no dummy I should average somewhere in the high 270's to 300kbs. It takes me 20 minutes to watch a 5 minute video with all the buffering. If I upload something, I am averaging 80kbs which I can live with. I only upload a video or 2.
I phoned support and they told me my modem was going bad and should get another one, then try that. Did that, no change. Call support and they said everything is in order on their end. They have no issues with my line and everything is reading fine with all line tests.There is only 1 phone line in the whole house. DSL is on it since we have to telephone number just a dedicated dsl line.
I am using a Actiontec Modem Router Combination. I am hoping to resolve this issue soon I am tired of going through a dead end support team that walks me through the same steps every time.
Thanks

I assume you get the 3355/751 from the transceiver statistics. If that is correct,the problem isn't in your link between the Modem/Router and Verizon. That leaves the router itself, and your PC.
Check the security settings on the router to make sure you aren't doing anything there that slows you down> In addition software firewalls on your PC, and Anti-Virus software can seriously degrade network performance.
You might also want to run the speedtest/connection analyses from Argonne National Labs, which will tell you what your connection is capable of, and where the delays are.
http://ndt.anl.gov/

I click on the button for download de os x maverick but i doesn't do anything.. it doesn't download it .. nothing- why? .. ps: i run a macbook air 10.7.5

i click on the button for download de os x maverick but it doesnt do anything ... it doesnt download it.. dont know why

Hi,
The problem is resolved. Leave your system for sometime even though the progress bar does not move. Also, keep checking your disk space time to time and you can see that it is depleting. Aftrer a while the progress bar will start moving and you can download and install mavericks. I think it is actually downloading but the progress bar does not move immediately. I just have have 2 mbps broadband speed. So time is virtue here.

Yosemite Drops WiFi Download Speed 25%

I really had no problems with Yosemite on my late-2013 MBP Retina...until I did a Speedtest.net test of my Internet speed, in this case over a wi-fi connection to my router.
I routinely get 55-60 Mbit/sec download speeds, but with Yosemite I got only 40-45 Mbit/sec, roughly a 25% reduction. In case it was just a slowdown from my ISP, I checked using wired Ethernet, which showed my usual 55-60 Mbit/sec throughput. Toggling immediately back to wi-fi, the speed went back down to the 40-45 Mbit/range.
I saw others with wi-fi issues under Yosemite and tried the proposed solutions that some said fixed the wi-fi speed (and wi-fi drops) problems--turn off Bluetooth for one. Nothing helped. So I restored the Time Machine backup of my Mavericks installation and...everything wifi-related is back to normal. Same network speeds as before Yosemite.
Lesson learned--always do a full backup before a major OS upgrade just in case.

Vano3408 wrote:
Having issue on my D6633 since KitKat, now updated to LP 5.0.2 23.1.1.E.0.1 and still same. When I go in 5 meters from router behind 2 walls and signal strength decrease a bit download speed drops almost to Zero, but upload speed is ok.
Please check below video, I have 46080 / 3072 kbps for download /upload... Tried all possible settings combinations without success. Stamina mode never used..
http://1drv.ms/1DjjkcP
When near router 2-3 m without any obstacles download speed is ok.
Any other my phone (Samsunf S3 for ex.) have no such issue in same location...
Please advise what can cause such issue or it is my Sony hardware specific issue ? How can I solve it ?
This issue is not router specific, because same behavior at home and at work.
just in case following settings I have at home: router in mixed mode, 20/40MHz auto, WMM enabled
Download this and take a look which channel of your router had the best signal and make changes on your router to the best channel within 1-11. Try your speed test again to see if this helps.
https://play.google.com/store/apps/details?id=com.farproc.wifi.analyzer&hl=en
You may also want to ensure that no body is downloading or torrent if your home network is shared with other users.
I can accept failure.... I can't accept not trying - Michael Jordan

In Firefox can not see the Downloads window, in the jump in the boot to be seen - the download speed Downloaded much and now can not see how to fix it?

in Firefox can not see the Downloads window, in the jump in the boot to be seen - the download speed
Downloaded much and now can not see how to fix it?

I hate the new downloads-in-a-tab scheme. This was an unnecessary change in my book (if it aint broke, don't "fix it").
So in order to get it back, I performed the about:config browser.download.useToolkitUI change, but now all I get is a blank download window that pops up every time I download something.
Is there something else that I need to do? I've checked the change and it was saved, but it didn't resolve my issue as much as it just caused me a new issue.

WRT310N Playstation 3 Slow Download speed and general lag

Hey guys, I just recently bought the WRT310N and got both of my computers working with it. One is wired directly into the router, while the other is running off wireless. My Playstation 3 is able to connect to the router but I am getting an extremely slow connection speed.
Right now, both PC's get about 6.4-6.5 Mbps download speed while my Playstation is anywhere from 600 Kbs to 1.2 Mbps. I have plugged in my Playstation 3 directly into the modem and got a speed of 3.2 Mbps and was downloaded a demo very fast, but I do not recieve anywhere near those results when using it wireless.
Any advice? I have tried opening the ports, but that only seemed to slow it down. A couple of days ago I opened the ports specific to the game NHL 10 and for two days I was getting such a good speed in the game that it felt like I was playing offline, which was great! Then this morning, it just seemed do a complete 180. Now when I play the game I get an extreme amount of lag, and my other games like CoD4 get random lag spikes. Like, I'll be running and I get a lag spike which seems to happen fairly consistently every minute or so.
Any advice? Should I try opening the ports again or what?
Message Edited by Nimer on 10-02-2009 03:58 PM

I think you need to adjust the wireless settings of your Router, The wireless settings on your Router must have been setup to its default that's the reason you are receiving low signal strength on your PS3.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Here select manual configuration...Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Loss of download speed using airport extreme and express.

I have Wifi using an Airport extreme base station and an airport express extender. However, the download speed drops from 21 Mbps to 8 Mbps. Any suggestions to boost the express other than an ethernet connection which would be difficult.

Temporarily, power down the AirPort Express and take speed measurement at that exact location.
Whatever that is.....likely in the 8-10 Mpbs range......is what the Express will try to "extend".
In other words, the Express can only extend the bandwidth or speed that it receives. It cannot make the connection that it receives go any faster. In that regard, the term "repeater" is probably a more accurate description of what the Express is trying to accomplish.
If you want the Express to extend faster speeds, then it must be located closer to the AirPort Extreme. In addition, anything that you can do to reduce any obstructions in the signal path between the AirPorts will help.
Ideally, you want a line-of-sight relationship between the AirPorts to help reduce the amount of speed loss that occurs with any wireless connection.

New Infinity 2 poor real life download speeds

Hi
I'm hoping someone can help. I had infinity 2 installed on Tuesday and have had poor download speeds since. Now I use mainly iPads and iPhones for connecting to the internet.
My connection downstream on my modem says I'm connected at 78.12 Mbps however I can stand right next to it and try download something from sky go and this downloads at 11-12mbps. This doesn't seem right to me however as it is wireless devices the BT help centre will not help me.
Solved!
Go to Solution.

Are you sure that it is your speeds that are slow or are you possibly confusing your Megabyte (MB) with Megabit (Mb)
A Megabyte (used for file size) and a Megabit (used for download speeds). People often assume that a download speed of 1 Megabit per second (1 Mbps) will allow them to download a 1 Megabyte file in one second. This is not the case, a Megabit is 1/8 as big as a Megabyte, meaning that to download a 1MB file in 1 second you would need a connection of 8Mbps. Most downloads are shown as MB/s
If this is not the problem can you use this speed tester then carry out the further diagnostics and post back a screen shot of all the results including your IP profile for up and down. This test must be done with a wired connection for an accurate reading.
http://speedtest.btwholesale.com/

Slow Internet download speed, OSX 10.9.5

Since updated to 10.9.5, my Mac Pro Internet download speed down to 7 Mbps,
and same on My MacBook Pro 10.9.5 too. both use to be 70 Mbps.
I am paying $50.00 extra to get the highest speed from Time Warner.
My iMac is 10.9.3, tops 70 Mbps.
My iPhone 5s tops tops 30 Mbps
All in same WiFi network.
Upload speed all seem to be fine with 5 Mbps.
Mac Pro = Mid 2010
Processor 2.8 GHz Quad-Core Intel Xeon
Memory 16 GB 1066 MHz DDR3 ECC
Graphics ATI Radeon HD 5770 1024 MB
Mac Book Pro = Retina, 13-inch Late 2012
Memory = 8 GB
Something wrong!

Even the 'respected' tools like Onyx, if you look at what (each and every update) states in the "what is new" and changes will be to improve compatibility.
Never use or install anything (and I include OS X updates in that category) without cloning your system and having TimeMachine that is current, and backup(s) that will be off line.
Some cannot be trashed or deleted or removed without using an "uninstall app" or the installer, doing so without can mean having to reinstall first.
Or wipe the drive and restore from a known good backup set.
Some tips:
https://discussions.apple.com/thread/6522256
What to look for if your system is slower than normal etc:
https://discussions.apple.com/thread/4873022
for malware, check out this user tip (and his other pages too!)

V e e e r r y S l o o o o w Movie Rental Download Speeds

My setup: In my home office is a cable modem connected to my locally owned and operated ISP's coax feed. It's a city operated fiber network (Ashland Fiber Network), not a ComCast/Charter/Verizon conglomerate. The modem is connected to a Time Capsule (500 MB) via ethernet. Also connected to the Time Caspsule via Ethernet is a 2.4 GHz 24" iMac. The Apple TV is in my living room about 30' away through one wood-frame wall.
I get consistent >8 Mb/sec download speeds from Speedtest.net both on my office (Ethernet) iMac and on my MacBook via 802.11g while sitting next to the Apple TV in my living room. The Apple TV shows 5 bars on its signal strength meter, and is running the latest (2.02) software. I have the Airport Utility setup to run 802.11n (802.11b/g compatible) so that it'll work with both the Apple TV and my 802.11g MacBook. There are no 2.4 GHz wireless phones in my house, and no other WiFi devices connected. There are several other WiFi networks within range in my neighborhood, but I use WPA2 Personal security to isolate my network.
My problem: I have tried only 1 SD movie download. but it took 37 minutes to reach "Ready to Play," and then choked after playing for 56 minutes. So rather than wait for more of the movie to download, I went to bed and watched the rest of it the next day. I've rented 2 HD movies, the first download notice told me that it would take 13 hours to be ready to play, and the next said 11 hours. Both times I just went to bed and watched the movie the next day.
Trailers generally take anywhere from 2-5 mins. to begin playing, and they almost always choke after about a minute and have to download more to continue playing. They play much faster on my iMac when downloaded from Apple's Quicktime site, though I can't be sure if different servers are involved there.
This scenario does not jibe at all with what Apple tells me I should expect from the Apple TV, nor with what I read about here on the Apple Discussion boards.
Things I've tried: 1) Changing the WiFi channel from Auto to a discrete channel--I've tried four different channels now. 2) Switching to 802.11n only--both at 2.4 GHz and at 5 Ghz. 3) Unplugging and removing the batteries from my 5.8 GHz wireless phones. 4) Moving the Apple TV a 6' HDMI cable's length away from the TV and sound system in my living room. 4) Resetting everything several times, even once back to 2.0 before reinstalling 2.02. 5) I even unplugged the microwave in the kitchen. About the only obvious thing I haven't yet tried is stringing an ethernet cable from my Time Capsule to the Apple TV because I don't have one that long and would rather not strip down my entire setup just to test that. But it looks like I'm going to have to.
I've had four conversations with Apple tech support, the last one after being bumped up to level 2 support. They had me do (among other things) a 100-ping test using Network Utility between the my iMac and the Apple TV--no dropped packets and the network speed was, according to them, well within spec. When I told them all the other stuff I've tried, they had no suggestion other than: "Something is interfering with your signal."
I took the Apple TV to my local Apple Authorized Dealer (the nearest Apple Store is 300 miles away). It checked out fine and ran great on their network. I got to try downloading a few trailers there and they ran almost instantaneously. Now, they informed me that their network runs at ~15 Mb/sec, but they also have about 30 computers hooked up to it.
Anyway, I read here that almost all of you are seeing much faster download speeds on your Apple TVs, even those of you with DSL. And it seems pretty clear that I'm experiencing some sort of interference here, but can't seem to locate the source. So, my question is: What other possible sources of interference might I be getting, and how might I go about locating them?

cause i bot stock wrote:
How does downloading via your iMac respond?
I haven't tried downloading a movie from iTunes to see if there's a substantial difference, and you can't rent HD movies from iTunes, only SD. Trailers download faster, but there's no telling if they're coming from the same servers as Apple TV's trailers (nor if iTunes movies are, for that matter).
I'm quick to blame the time capsule and time machine. Similar to your problems with AppleTV, I've never had time machine work properly. All it does is suck up all my resources while taking days to do anything.
Unlike some, I've had zero setup or operating problems with my Time Capsule. Works like a charm and doesn't seem to slow anything down on my iMac as far as I can tell.

Transmit rate vs. Download speed: should I switch everything to 5GHZ or does it matter?

Thanks in advance for any help that you can give me. I am not well-schooled in networking so, after doing a lot of research and not being able to get clarity, I figured I would write what I understand and hope that somebody here could point me in the right direction. I have 3 airport stations (a time capsule dual band is the primary and 2 airport expresses) and they are all ethernet wired. All my devices are 802.11n capable and all the base stations are n capable. I have no strictly b/g devices, only n devices. No matter what base station a device is connected to, the speedtest.net rate is about 17mbps (I pay for 18mbps) so that is good. However, the "transmit rate" (and I don't really understand what this does) varies depending on what base station my device hooks into. Whenever I am near the time capsule (primary station), my devices hook in at 5Ghz and I get a transmit rate of about 240 to 300 and a 17mbps download speed. But when I hook into either of the other 2 aiport expresses, it shows that I am hooked into 2.4Ghz and the transmit rate is about 50 to 130, but I still get the 17mbps download speed. I know I can change both expresses to only do 5Ghz. Keep in mind, the speedtest.net test always shows about 17mbps download speed no matter what base station my device connects to. I am not sure I understand what the transmit rate indicates. I want to make my network the fastest it can be no matter what base station I use.
So, my question is should I change the other 2 airport extreme base stations to operate as 5Ghz n network only so that I have 5Ghz operating throughout my whole house which will give a higher "transmit rate" and will that make my experience faster even though I already get maximum 17mbps download speed? Also, if you could, please explain to me the difference between ISP download speed and "transmit rate" because I don't really understand the difference...I mean how does download speed affect my experience vs. how does transmit rate affect my experience? Do I really need to have a higher "transmit rate" to increase my speed or is just having 17mbps download speed necessary and the transmit rate doesn't matter?
One other thing you might need to know: I don't have any 2.4 ghz devices that might interfere with my network (my cordless phones are 1.9Ghz)
Thanks again for the help.

Think of it like this.. Change moving data in air to water in pipes.
You have a 1/2" pipe coming from the ISP into your house..
Inside your house you have 5" and 2" pipes.. (this represents the speeds or flow rate if you like, 1/2" is all the ISP gives you.. but your ethernet is a huge pipe.. think of it as infinite for this situation,, and 5" pipe that is 5ghz and 2" pipe is 2.4ghz.. this is just illustration remember it is area not diameter that matters).
If you transfer files between the computer on the TC to the TC hard disk.. you get all the 5" pipe.. very fast.
If you copy a file between computer on the TC and device on the express.. you are limited by the 2" pipe.. everything goes at the speed the 2" pipe can manage.
Now you do something with internet.. 5" pipe can get the same throughput as the 2" pipe because it is only 1/2"
Pipes btw are still in imperial even if you are in a metric country pretty often.
But I hope that illustrates the situation..
If a computer on 5" pipe and computer on 2" pipe are both trying to access internet .. they both still have to share the 1/2" pipe. In a perfect world they both get half your 18mbps if they are accessing it at the same time.. (QoS represent a flow valve that says this pipe should get more flow even if it is smaller so I shut the valve down on 5" to make sure it only gets what the 2" can get.. no more.. to be fair.).
Same as water in pipes.. the 1/2" pipe can never fill the 5" or even the 2" pipe.. the 2" cannot fill the 5" so the fastest would be everything on 5" pipes.. since you are unlikely to be able to afford a 5" pipe from the ISP then you accept everything is going to go slower when internet is involved.
Jumping out of my illustration..
Apple made 2.4ghz max out at 150mbps..
Although some of the later stuff can get better than that,, 217mbps.
The 5ghz is faster because it is has more bandwidth.. up to 1200mbps in the newest AC .. 450 on Gen3,4 TC and 300 on the older gen1,2
BUT the range is poor.. so generally better sticking with 2.4ghz for express.. they are not high power devices at all.
2.4ghz has better range and penetration.. you are going to be just fine with internet access.. and your setup is actually working really well.. There are some overheads on wireless so you do not quite hit wired speeds.

Download Speed on PIX 515E is Pretty Slow

Hello, I have a PIX 515E set up between our office switch and our Comcast Business Router and the download speeds are not as fast as they should be. We are paying for 30 down 30 up but it's more like 10 down 30 up. I plugged in a computer directly into the router and got 30/30 so I know its not a comcast issue. I think it might be the low amount of memory on the PIX because its running at 109 out of a total 128mb. The PIX has a site-to-site VPN tunnel with a remote ASA 5520 firewall. The inside/outside ports are both auto/auto. The running config is only 161 lines.
Here's some information about the PIX 515E...
Version 8.0(4)
ASDM 6.1(3)
Memory 128MB
Here is the running config..
Result of the command: "show running-config"
: Saved
PIX Version 8.0(4)
hostname --------------------
domain-name -----------------
enable password -------------------------
passwd --------------- encrypted
names
name 1.1.1.1 Data-Center-Firewall    #### Outside Address Changed
name 10.0.0.0 Data-Center-Subnet
dns-guard
interface Ethernet0
nameif inside
security-level 100
ip address 10.10.1.1 255.255.255.0 standby 10.10.1.254
interface Ethernet1
nameif outside
security-level 0
ip address 2.2.2.1 255.255.255.252   #### Outside Address Changed
interface Ethernet2
description LAN/STATE Failover Interface
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns server-group DefaultDNS
domain-name -------------
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service http8080 tcp
description http8080
port-object eq 8080
object-group service DM_INLINE_TCP_1 tcp
port-object range 50000 50100
port-object eq 990
access-list outside_access_in remark ip, tcp/990
access-list outside_access_in extended permit tcp host 1.1.1.1 host 2.2.2.5 object-group DM_INLINE_TCP_1
access-list outside_access_in extended permit icmp any any
access-list ACL-VPN extended permit ip 10.10.1.0 255.255.255.0 Data-Center-Subnet 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
failover
failover lan unit primary
failover lan interface failover Ethernet2
failover lan enable
failover key *****
failover replication http
failover mac address Ethernet0 001e.f732.008f 000d.28f9.628f
failover mac address Ethernet1 001e.f732.0090 000d.28f9.6290
failover link failover Ethernet2
failover interface ip failover 10.10.10.10 255.255.255.252 standby 10.10.10.20
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm image flash:/asdm-613.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 0 access-list ACL-VPN
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) 2.2.2.5 10.10.1.102 netmask 255.255.255.255
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 2.2.2.2 1
route inside 10.10.0.0 255.255.255.0 10.10.1.2 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 10.10.0.0 255.255.255.0 inside
http 10.10.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
service resetoutside
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set AES128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map MAP-VPN 1 match address ACL-VPN
crypto map MAP-VPN 1 set pfs
crypto map MAP-VPN 1 set peer Data-Center-Firewall
crypto map MAP-VPN 1 set transform-set ESP-3DES-SHA
crypto map MAP-VPN 1 set security-association lifetime seconds 28800
crypto map MAP-VPN 1 set security-association lifetime kilobytes 4608000
crypto map MAP-VPN interface outside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 10.10.1.0 255.255.255.0 inside
telnet 10.10.0.0 255.255.255.0 inside
telnet timeout 5
ssh 10.10.0.0 255.255.255.0 inside
ssh 10.10.1.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared-key *
class-map class_ftp
match port tcp eq ftp-data
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
class class_ftp
inspect ftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:b795d4f5f5da3d8283d452ba857d5534
: end

Please check on the speed and duplex settings whether the downstream and upstream links are fine and healthy.
Inside/outside are both set to auto/auto at
Check for the processes usage of the cpu of the pix.
CPU is running at 2%
Process:      tmatch compile thread, PROC_PC_TOTAL: 2, MAXHOG: 8, LASTHOG: 8
LASTHOG At:   19:01:15 EST Dec 31 1992
PC:           26b616 (suspend)
Process:      tmatch compile thread, NUMHOG: 2, MAXHOG: 8, LASTHOG: 8
LASTHOG At:   19:01:15 EST Dec 31 1992
PC:           26b616 (suspend)
Traceback:    26b616 26bdb9 26ec89 1182b3
Process:      Dispatch Unit, NUMHOG: 1, MAXHOG: 5, LASTHOG: 5
LASTHOG At:   09:25:12 EDT Jul 18 2012
PC:           130114b (interrupt)
Traceback:    100178 12edd0c 9771e5 8c0e66 927164 928996 8ec3f5
              8ec7ed 79d35e 2780c3 1182b3
Process:      Unicorn Admin Handler, NUMHOG: 1, MAXHOG: 5, LASTHOG: 5
LASTHOG At:   12:27:25 EDT Jul 18 2012
PC:           130114b (interrupt)
Traceback:    100178 d870cb 13016b3 15cf68 e91a6f e9118b abfcea
              a7cb2e a7daeb 18d800 5ae9a9 5a6aa0 5a7272 5a75e5
Process:      Unicorn Admin Handler, PROC_PC_TOTAL: 4, MAXHOG: 7, LASTHOG: 7
LASTHOG At:   12:34:10 EDT Jul 18 2012
PC:           5ae903 (suspend)
Process:      Unicorn Admin Handler, NUMHOG: 4, MAXHOG: 7, LASTHOG: 7
LASTHOG At:   12:34:10 EDT Jul 18 2012
PC:           5ae903 (suspend)
Traceback:    5ae903 5a6aa0 5a7272 5a75e5 5ad3d5 1182b3
Process:      Unicorn Admin Handler, PROC_PC_TOTAL: 4, MAXHOG: 5, LASTHOG: 5
LASTHOG At:   12:37:47 EDT Jul 18 2012
PC:           f4078b (suspend)
Process:      Unicorn Admin Handler, NUMHOG: 4, MAXHOG: 5, LASTHOG: 5
LASTHOG At:   12:37:47 EDT Jul 18 2012
PC:           f4078b (suspend)
Traceback:    f40be2 130f41e aab54d aac3b0 5a6c2e 5a7272 5a75e5
              5ad3d5 1182b3
Process:      IKE Daemon, NUMHOG: 1, MAXHOG: 5, LASTHOG: 5
LASTHOG At:   23:07:40 EDT Jul 19 2012
PC:           1b6dd0 (interrupt)
Traceback:    100178 1b8a31 1baaeb 6438d7 12efc6f 64250b 653fe9
              654b78 1182b3
Process:      IKE Daemon, PROC_PC_TOTAL: 347, MAXHOG: 31, LASTHOG: 30
LASTHOG At:   16:01:55 EDT Jul 23 2012
PC:           654bab (suspend)
Process:      CTM message handler, PROC_PC_TOTAL: 346, MAXHOG: 27, LASTHOG: 27
LASTHOG At:   16:01:55 EDT Jul 23 2012
PC:           2087ec (suspend)
Process:      IKE Daemon, NUMHOG: 693, MAXHOG: 31, LASTHOG: 27
LASTHOG At:   16:01:55 EDT Jul 23 2012
PC:           654bab (suspend)
Traceback:    1182b3
Process:      Unicorn Admin Handler, NUMHOG: 1, MAXHOG: 5, LASTHOG: 5
LASTHOG At:   17:23:30 EDT Jul 23 2012
PC:           130003b (interrupt)
Traceback:    100178 13008b8 f5a0cd f5ac32 f5ae40 f60828 f617c1
              d38a0d aab50b aac14a 5a6c2e 5a7272 5a75e5 5ad3d5
Process:      Dispatch Unit, PROC_PC_TOTAL: 227, MAXHOG: 432, LASTHOG: 35
LASTHOG At:   17:37:03 EDT Jul 23 2012
PC:           278207 (suspend)
Process:      Dispatch Unit, NUMHOG: 227, MAXHOG: 432, LASTHOG: 35
LASTHOG At:   17:37:03 EDT Jul 23 2012
PC:           278207 (suspend)
Traceback:    278207 1182b3
Process:      Unicorn Admin Handler, PROC_PC_TOTAL: 1901, MAXHOG: 8, LASTHOG: 7
LASTHOG At:   17:44:20 EDT Jul 23 2012
PC:           118ed5 (suspend)
Process:      Unicorn Admin Handler, NUMHOG: 1901, MAXHOG: 8, LASTHOG: 7
LASTHOG At:   17:44:20 EDT Jul 23 2012
PC:           118ed5 (suspend)
Traceback:    118ed5 b2d032 f5a80d f5ac0a f5ae40 f607e5 f617c1
              d38a0d aab50b aac14a 5a6c2e 5a7272 5a75e5 5ad3d5
CPU hog threshold (msec): 5.120
Last cleared: None
Check on the inetrface whetehr u get any crc/input/overrun errors. Please check with the physical connectivity.
Interface Ethernet0 "inside", is up, line protocol is up
Hardware is i82559, BW 100 Mbps, DLY 100 usec
    Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
    MAC address __________, MTU 1500
    IP address 10.10.1.1, subnet mask 255.255.255.0
    60862937 packets input, 29025667892 bytes, 0 no buffer
    Received 1371 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops
    68515603 packets output, 44084404472 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    input queue (curr/max packets): hardware (0/1) software (0/47)
    output queue (curr/max packets): hardware (0/67) software (0/1)
Traffic Statistics for "inside":
    60997029 packets input, 28080179952 bytes
    68553614 packets output, 43104566708 bytes
    29544 packets dropped
      1 minute input rate 63 pkts/sec, 30371 bytes/sec
      1 minute output rate 64 pkts/sec, 16557 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 91 pkts/sec, 45254 bytes/sec
      5 minute output rate 93 pkts/sec, 56181 bytes/sec
      5 minute drop rate, 0 pkts/sec
Interface Ethernet1 "outside", is up, line protocol is up
Hardware is i82559, BW 100 Mbps, DLY 100 usec
    Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
    MAC address ___________, MTU 1500
    IP address ___________, subnet mask 255.255.255.252
    67730933 packets input, 44248541375 bytes, 0 no buffer
    Received 4493 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops
    60418640 packets output, 29310509840 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    input queue (curr/max packets): hardware (0/1) software (0/39)
    output queue (curr/max packets): hardware (0/42) software (0/1)
Traffic Statistics for "outside":
    67782987 packets input, 43276611710 bytes
    60562287 packets output, 28342787997 bytes
    206651 packets dropped
      1 minute input rate 57 pkts/sec, 14273 bytes/sec
      1 minute output rate 61 pkts/sec, 30258 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 89 pkts/sec, 54426 bytes/sec
      5 minute output rate 87 pkts/sec, 45115 bytes/sec
      5 minute drop rate, 0 pkts/sec
enable flowcontrol recieve on on the firewall interfaces and switch/router interfaces connected to the firewall.
Not sure how to do that.

Download speeds dead in Mavericks!

Similar Messages

Maybe you are looking for