DPC3825 Blocks communication between wired and wireless
I currently have six devices connected to this cable modem/router over wireless and two devices connected through wired ethernet connections. I can ping the wireless devices from the wired device without issue, but services such as Apple's file sharing, AirPlay, etc. are blocked - the AppleTV can't see the Mac Mini unless they're both wired or both wireless.
I have no MAC filtering enabled. I use WPA security with a pre-shared key. CTS protection mode is disabled. WMM is enabled, "No ACK" is disabled.
SPI Firewall protection is disabled. Block anonymous internet requests is checked. There is no IP filtering, no parental controls, no time of day rules, etc. I have no port filtering, forwarding, or triggering. DMZ is disabled. UPnP is disabled.
I'm using firmware version
DPC3825-v302r12901-100914a
I'm hoping there's something simple that I'm missing here. Any thoughts?
Hi Mikael
Thank you for your question. However, this community is for Cisco Small Business Products which the DPC3825 is not.
We did some research for you and found out that this is an internet service provider (ISP) supported product. In otherwords you need to contact your ISP or technology reseller that you purchased this from to help you with your question.
Regards,
Cindy Toy
Cisco Small Business Community Manager
for Cisco Small Business Products
www.cisco.com/go/smallbizsupport
Similar Messages
-
NetworkManager - switching between wired and wireless
Hello!
I’ve set up a new laptop with Arch and now have a question concerning NetworkManager. Is it possible in NM to switch between wired and wireless connections like it is with Connman (https://wiki.archlinux.org/index.php/Co … d_wireless)?
So far it appears that NM only disables the wired connection when wireless is used but keeps the wireless alive when switching to wired.
I have already looked for a corresponding configuration but couldn’t find anything that helps.
Thanks in advance.Easy Mode:
You can install the tlp-rdw package and edit the /etc/default/tlp configuration file which has an option that does that.
Hard Mode:
If you don't want to install a package and its dependencies, you can write your own script and put it in /etc/NetworkManager/dispatcher.d and have the NetworkManager dispatcher hook run the script (which is actually what tlp-rdw does but you don't have to install the tlp package as a dependency)
Note: tlp is a power manager and if you have any other power managers installed it might conflict with them so be wary of that.
Here is the wiki page on tlp https://wiki.archlinux.org/index.php/Tlp
Last edited by fungle (2014-08-05 23:05:00) -
Sharing iTunes between wired and wireless Macs
Hi,
I have a Mac laptop connected wirelessly to an Airport Express -- which is wired to a desktop Mac Mini. I'm trying to share music but cannot. I've done all the proper settings in the iTunes preferences and the same in System Preferences -- I think -- on both computers, but on neither computer is anything showing in the Sources window. It says that there are no users online.
Is there something in the System Preferences box that I'm missing? Should I turn the firewall off (I shouldn't need to, since I've checked the iTunes Sharing box)? Is the main problem here that you can't share music between a wired and wireless computer? (This would be a bit strange to me, but you never know.)
One other thing. I was trying out the network and I can only get access to the wired Mini's Public folder as a Guest, not as a Registered User. Is there something very badly wrong here?
Any suggestions welcome. Thanks.Thanks for the rapid response. All of those preferences, however, are already set properly (i.e., as you said) on both computers. When I try to go to the Network, I can access the wired desktop Mini's hard drive, but when I try to do it on the mini to get into the laptop's it can't find the afp. It just keeps searching but then says it doesn't exist. Not sure if this network-connectivity problem is relevant or not for this particular issue of iTunes sharing. Grateful for any advice.
-
Bridge between wired and wireless
This is what I am hoping to accomplish
router *****wireless connection 802.11******wlan0 - laptop - eth0 --------Wired ethernet---------------- another host(s)
routers IP is 192.168.1.1
The "other host(s)" need to be able to pull information via dhcp from the router.
What I've tried so far
I've installed bridge-utils and enabled ip forwarding in /proc
brctl addbr br0
brctl addif br0 wlan0
brctl addif br0 eth0
This is where I get lost. I think I need to manually configure wlan0 and eth0. In Ubuntu I think I remember setting br0 to bridge_ports in /etc/network.d/interfaces but I am not sure how to do this in Arch.
Any suggestions?
Thanks
band-aid
Ok I think I have been going about this all wrong, is it possible to do what I need to do using iptables masquerading?
Last edited by band-aid (2008-07-21 07:20:33)You can use bridging OR ip masquerading - you don't need both. If you use bridging, wlan0 and eth0 join the bridge, which then gets its own virtual interface br0. This is the interface that gets an IP address, so that the laptop can continue to function normally. In this scenario, everything is on single subnet, and no ip forwarding or routing manipulation is required.
If you use IP masquerading, you're basically setting up NAT (Network Address Translation). The router and wlan0 are on one subnet, eth0 and the other hosts(s) are on another, and the laptop functions as the router between the two - as well as doing its normal laptop-y things, of course.
There are probably various pros and cons either way - one that occurs to me now is that the IP masquerade option will probably leave you with a double-NAT setup, because your existing router is most likely doing NAT already. This may or may not be a problem for you - depends really on the kind of network apps you will be running. Personally, I prefer bridging in this kind of situation, just because I find it simpler. -
Autoselection for a switch between wired and wireless network
Hello,
We currently have a VTC codec installed on a mobile cart that can connect via wireless or wired network. The cart has the Linksys WET610N Dual-Band Wireless-N gaming and video adapter bridge. If you want to go wireless you will have to unplug the CAT5 that goes into the walljack and plug in the cable from the bridge into the codec.
We need a 3-5 port switch. Port 1 will connect to the wireless bridge. Port 2 would be available to connect to a wall jack. Port 3 will connect to the codec.
We need the ability for the switch to autoselect port 1 and 2. If Port 2 is not connected (no link light), then Port 1 will be active. If Port 2 is active, Port 1 will be inactive.
I need to know how to configure the bridge and a network switch if this is scenerio is possible. Any help is appreciated.
Thanks,
AaronWell, I thought i had tried this before, but I followed another board's suggestion of turning of IGMP proxy and it is now working. I can see my iTunes server which is wired on my wireless devices.
-
WRT54G2 v1 - Substantial Speed Difference Between Wired and Wireless Connection
Hi everyone,
I have a WRT54G2 v.1 router connected to an RCN Cable Modem. My download transfer rate direct from the cable modem is 18 Mbps. Thankfully, I can get the same download rate when I plug my laptop into a wired ethernet connection from the router. However, the wireless connection only gets a download rate of 0.8Mbps. Also, my wireless card is pretty new (Intel 4965AGN) and has the latest driver (I can get far higher download rates at mobile hotspots, for instance). Here is what I've tried with the router:
- I've upgraded the router firmware to the latest build (Version 1.0.04, 07/08/2009).
- I've tried multiple channels on the network (1, 6, 11).
- I use WPA Security.
- Upon advice from the Linksys live chat support, I've changed the MTU settings to manual and set them to 1300.
- They also recommended that I change the following settings: “RTS Threshold” – 2304 “Fragmentation Threshold” – 2304 “Beacon Interval” – 50
- And of course: I've got my own SSID. The router is 5 feet off the ground. There are no other wireless devices that would cause interference. The router is not near large metal objects, fish tanks, or any other physical obstruction.
Is there anything else I can do? Thank you so much in advance for reading. I really appreciate it.Also, is there anything to the fact that only the download rate seems to change?
Wired:
Wireless: -
Communication between : AP and WLAN controller
Hi,
The communication between AP and WLAN Controller is ( Data and Control ) UDP.
Source port 1024 and destination port 12222 and 12223. Actually which device listen to which port or both should listen as control and data can be generated from both the devices.
How does the user ( wireless client) traffic is switched - if user traffic is a TCP traffic. It will be sent to WLANC and then WLANC forwards it to respective VLAN or default gateway ( depending upon the destination in the packet ).
Please explain / share the experience.
any link on cisco.com
Thanka in advance
Subodh"the LWAPP Control and Data messages are encapsulated in UDP packets that are carried over the IP network. The only requirement is established IP connectivity between the access points and the WLC. The LWAPP tunnel uses the access point's IP address and the WLC's AP Manager interface IP address as endpoints. The AP Manager interface is explained in further detail in the
implementation section. On the access point side, both LWAPP Control and Data messages use an ephemeral port that is derived from a hash of the access point MAC address as the UDP port. On the WLC side, LWAPP Data messages always use UDP port 12222. On the WLC side, LWAPP Control messages always use UDP port 12223.
The mechanics and sequencing of Layer 3 LWAPP are similar to Layer 2 LWAPP except that the packets are carried in UDP packets instead of being encapsulated in Ethernet frames."
Taken from "Cisco 440X Series Wireless LAN Controllers Deployment Guide" -
A very strange wired and wireless network issue
Hello,
I have never had any issue at all with my macbook (2008) until this week, I use it both for work and personal use.
Most of time, I'm used to be on customer site, so I use wired and wireless connections depending of the situation....
I have never had any issue at all with wifi neither ethernet connections during three years, until this week... and I can say this is the most strange thing I have ever seen....
Using wired or wireless connection, always the speed of network was really good, at home, many customers, etc never had any problem...
But this week I'm currently out of home, and the hotel where I'm staying I'm having very poor network rate....
Using wireless connection, the download speed is no more than 10kb.... and using ethernet I get less speed... but during the day I'm on customer site, using the ethernet connection and download speed is really good, more than 500k-800k....
I have already tried in the hotel few wifi connections (there are three) and differents wired connections (in diferent rooms) and the download speed is always the same, no more than 10kb...
During this afternoon, I could go into hotel's lab and could connect directly to the router using cable, same speed no more than 10kb....
The most strange thing is on their computers the download speed using wired connection is around 6Mb....
how is possible I'm getting no more than 10kb of download speed when the pc's at hotel using same wired connection gets 6Mb?
I have already deleted current network connections, execute onyx to clear everything, perform dhcp connection, tried manual ip etc, and always the results are the same...
I know there is no problem with the macbook, because it works pretty good at every location I've been... but until this week...
Sincerely I'm getting a little crazy here, I'll appreciate any help!!!
thanks in advanceI've seen something like this on my T400 when it was running Vista. Now that I use Win 7 it's been OK. I rather doubt that your issue is the same but I'm tossing it out here just on the off chance.
Im my case, I had to downgrade my Intel 5300 card to a 5100 (as suggested by a Lenovo 2nd-tier tech) to get things working.
My symptoms were a little different. Wifi was fine until I went back to a wired network. After that, trying to use the same wifi AP as before would end up associated, but no internet access. DHCP wasn't working. The GUI "find" app didn't work as expected either. Some APs showed up, and some didn't.
If I configured for automatic connection to my home AP it would try and fail. Just rebooting at that point would again attempt an automatic connection that would succeed.
What I have noticed now that I run Win 7 is that Access Connections is completely useless. Often the "finder" doesn't show an AP 3 feet away. I didn't notice that this happened after a switch from wired, but maybe.
Are you using Access Connections? If so, you might try uninstalling it.
Sorry I can't be of real help,
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество -
Error during VM container communication between ABAP and JAVA
Hello,
While creation of SC, I am getting error "Error during VM container communication between ABAP and JAVA"
Based on earlier responses in this forum, I checked following activity.
1. T Code - BBP_CND_CHECK_CUST
Result - IPC Pricing is Active and IPC is now running in VMC
2. Run Report - RSVMCRT_HEALTH_CHECK
Result - The Java component is deactivated
3. As per OSS note 854170, Profile parameters were existed as below
a) vmcj/enable - on
b) vmcj/option/maxJavaHeap = 200M
So, How to get Java component activated?
Thanks,
Rahul MandaleThanks Markus,
For SM53, I am getting resulets as " Java is not active on this application server - Message no. SVMCRT011"
Can you suggest, what I need to do for it? I can't use SRM Shopping cart because of it. thanks in advance, Rahul
and dev_w0 trace ....
trc file: "dev_w0", trc level: 1, release: "700"
ACTIVE TRACE LEVEL 1
ACTIVE TRACE COMPONENTS all, MJ
B
B Wed Aug 31 15:45:40 2011
B create_con (con_name=R/3)
B Loading DB library 'D:\usr\sap\CUS\DVEBMGS04\exe\dboraslib.dll' ...
B Library 'D:\usr\sap\CUS\DVEBMGS04\exe\dboraslib.dll' loaded
B Version of 'D:\usr\sap\CUS\DVEBMGS04\exe\dboraslib.dll' is "700.08", patchlevel (0.46)
B New connection 0 created
M sysno 04
M sid CUS
M systemid 560 (PC with Windows NT)
M relno 7000
M patchlevel 0
M patchno 52
M intno 20050900
M make: multithreaded, Unicode, optimized
M pid 456
M
M kernel runs with dp version 210000(ext=109000) (@(#) DPLIB-INT-VERSION-210000-UC)
M length of sys_adm_ext is 572 bytes
M ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 456) [dpxxdisp.c 1293]
I MtxInit: 30000 0 0
M DpSysAdmExtCreate: ABAP is active
M DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active
M DpShMCreate: sizeof(wp_adm) 18304 (1408)
M DpShMCreate: sizeof(tm_adm) 3954072 (19672)
M DpShMCreate: sizeof(wp_ca_adm) 24000 (80)
M DpShMCreate: sizeof(appc_ca_adm) 8000 (80)
M DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
M DpShMCreate: sizeof(comm_adm) 528064 (1048)
M DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
M DpShMCreate: sizeof(file_adm) 0 (72)
M DpShMCreate: sizeof(vmc_adm) 0 (1452)
M DpShMCreate: sizeof(wall_adm) (38456/34360/64/184)
M DpShMCreate: sizeof(gw_adm) 48
M DpShMCreate: SHM_DP_ADM_KEY (addr: 05C00040, size: 4613144)
M DpShMCreate: allocated sys_adm at 05C00040
M DpShMCreate: allocated wp_adm at 05C01E28
M DpShMCreate: allocated tm_adm_list at 05C065A8
M DpShMCreate: allocated tm_adm at 05C065D8
M DpShMCreate: allocated wp_ca_adm at 05FCBB70
M DpShMCreate: allocated appc_ca_adm at 05FD1930
M DpShMCreate: allocated comm_adm at 05FD3870
M DpShMCreate: system runs without file table
M DpShMCreate: allocated vmc_adm_list at 06054730
M DpShMCreate: allocated gw_adm at 06054770
M DpShMCreate: system runs without vmc_adm
M DpShMCreate: allocated ca_info at 060547A0
M DpShMCreate: allocated wall_adm at 060547A8
X EmInit: MmSetImplementation( 2 ).
X MM diagnostic options set: 0
X <ES> client 0 initializing ....
X Using implementation flat
M <EsNT> Memory Reset disabled as NT default
X ES initialized.
M
M Wed Aug 31 15:45:41 2011
M ThInit: running on host crmsys
M
M Wed Aug 31 15:45:42 2011
M calling db_connect ...
C Prepending D:\usr\sap\CUS\DVEBMGS04\exe to Path.
C
C Wed Aug 31 15:45:47 2011
C Client NLS settings: AMERICAN_AMERICA.UTF8
C Logon as OPS$-user to get SAPSR3's password
C Connecting as /@CRM on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 0619F158 061A46F4 061A3F7C
C Attaching to DB Server CRM (con_hdl=0,svchp=061A3EC8,svrhp=061B5794)
C Starting user session (con_hdl=0,svchp=061A3EC8,srvhp=061B5794,usrhp=061CA558)
C
C Wed Aug 31 15:45:48 2011
C Now '/@CRM' is connected (con_hdl 0, nls_hdl 0).
C Got SAPSR3's password from OPS$-user
C Disconnecting from connection 0 ...
C Closing user session (con_hdl=0,svchp=061A3EC8,usrhp=061CA558)
C Now I'm disconnected from ORACLE
C Connecting as SAPSR3/<pwd>@CRM on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 0619F158 061A46F4 061A3F7C
C Starting user session (con_hdl=0,svchp=061A3EC8,srvhp=061B5794,usrhp=061CA558)
C Now 'SAPSR3/<pwd>@CRM' is connected (con_hdl 0, nls_hdl 0).
C Database NLS settings: AMERICAN_AMERICA.UTF8
C Database instance CRM is running on CRMSYS with ORACLE version 10.2.0.1.0 since 20110831
B
B Wed Aug 31 15:45:49 2011
B Connection 0 opened (DBSL handle 0)
B Wp Hdl ConName ConId ConState TX PRM RCT TIM MAX OPT Date Time DBHost
B 000 000 R/3 000000000 ACTIVE NO YES NO 000 255 255 20110831 154542 CRMSYS
M db_connect o.k.
M ICT: exclude compression: .zip,.cs,.rar,.arj,.z,.gz,.tar,.lzh,.cab,.hqx,.ace,.jar,.ear,.war,.css,.pdf,.js,.gzip,.uue,.bz2,.iso,.sda,.sar,.gif
I
I Wed Aug 31 15:46:12 2011
I MtxInit: 0 0 0
M SHM_PRES_BUF (addr: 0A7C0040, size: 4400000)
M SHM_ROLL_AREA (addr: 788A0040, size: 61440000)
M SHM_PAGING_AREA (addr: 0AC00040, size: 32768000)
M SHM_ROLL_ADM (addr: 0CB50040, size: 615040)
M SHM_PAGING_ADM (addr: 0CBF0040, size: 525344)
M ThCreateNoBuffer allocated 544152 bytes for 1000 entries at 0CC80040
M ThCreateNoBuffer index size: 3000 elems
M ThCreateVBAdm allocated 12160 bytes (50 server) at 0CD10040
X EmInit: MmSetImplementation( 2 ).
X MM diagnostic options set: 0
X <ES> client 0 initializing ....
X Using implementation flat
X ES initialized.
B db_con_shm_ini: WP_ID = 0, WP_CNT = 13, CON_ID = -1
B dbtbxbuf: Buffer TABL (addr: 10E700C8, size: 30000000, end: 12B0C448)
B dbtbxbuf: Buffer TABLP (addr: 12B100C8, size: 10240000, end: 134D40C8)
B dbexpbuf: Buffer EIBUF (addr: 0FBA00D0, size: 4194304, end: 0FFA00D0)
B dbexpbuf: Buffer ESM (addr: 134E00D0, size: 4194304, end: 138E00D0)
B dbexpbuf: Buffer CUA (addr: 138F00D0, size: 3072000, end: 13BDE0D0)
B dbexpbuf: Buffer OTR (addr: 13BE00D0, size: 4194304, end: 13FE00D0)
M rdisp/reinitialize_code_page -> 0
M icm/accept_remote_trace_level -> 0
M rdisp/no_hooks_for_sqlbreak -> 0
M CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
S
S Wed Aug 31 15:46:15 2011
S *** init spool environment
S initialize debug system
T Stack direction is downwards.
T debug control: prepare exclude for printer trace
T new memory block 1946AA80
S
S Wed Aug 31 15:46:16 2011
S spool kernel/ddic check: Ok
S using table TSP02FX for frontend printing
S 1 spool work process(es) found
S frontend print via spool service enabled
S printer list size is 150
S printer type list size is 50
S queue size (profile) = 300
S hostspool list size = 3000
S option list size is 30
S found processing queue enabled
S found spool memory service RSPO-RCLOCKS at 1D6D00A8
S doing lock recovery
S setting server cache root
S found spool memory service RSPO-SERVERCACHE at 1D6D0430
S using messages for server info
S size of spec char cache entry: 297028 bytes (timeout 100 sec)
S size of open spool request entry: 2132 bytes
S immediate print option for implicitely closed spool requests is disabled
A
A Wed Aug 31 15:46:18 2011
A
A -PXA--
A PXA INITIALIZATION
A PXA: Fragment Size too small: 73 MB, reducing # of fragments
A System page size: 4kb, total admin_size: 5132kb, dir_size: 5076kb.
A Attached to PXA (address 688A0040, size 150000K)
A abap/pxa = shared protect gen_remote
A PXA INITIALIZATION FINISHED
A -PXA--
A
A
A Wed Aug 31 15:46:20 2011
A ABAP ShmAdm attached (addr=57A40000 leng=20955136 end=58E3C000)
A >> Shm MMADM area (addr=57EB5E58 leng=126176 end=57ED4B38)
A >> Shm MMDAT area (addr=57ED5000 leng=16150528 end=58E3C000)
A RFC Destination> destination crmsys_CUS_04 host crmsys system CUS systnr 4 (crmsys_CUS_04)
A
A Wed Aug 31 15:46:21 2011
A RFC Options> H=crmsys,S=04,d=2,
A RFC FRFC> fallback activ but this is not a central instance.
A
A RFC rfc/signon_error_log = -1
A RFC rfc/dump_connection_info = 0
A RFC rfc/dump_client_info = 0
A RFC rfc/cp_convert/ignore_error = 1
A RFC rfc/cp_convert/conversion_char = 23
A RFC rfc/wan_compress/threshold = 251
A RFC rfc/recorder_pcs not set, use defaule value: 2
A RFC rfc/delta_trc_level not set, use default value: 0
A RFC rfc/no_uuid_check not set, use default value: 0
A RFC rfc/bc_ignore_thcmaccp_retcode not set, use default value: 0
A RFC Method> initialize RemObjDriver for ABAP Objects
M ThrCreateShObjects allocated 13730 bytes at 0FFB0040
N
N Wed Aug 31 15:46:22 2011
N SsfSapSecin: putenv(SECUDIR=D:\usr\sap\CUS\DVEBMGS04\sec): ok
N
N =================================================
N === SSF INITIALIZATION:
N ===...SSF Security Toolkit name SAPSECULIB .
N ===...SSF trace level is 0 .
N ===...SSF library is D:\usr\sap\CUS\DVEBMGS04\exe\sapsecu.dll .
N ===...SSF hash algorithm is SHA1 .
N ===...SSF symmetric encryption algorithm is DES-CBC .
N ===...sucessfully completed.
N =================================================
N
N Wed Aug 31 15:46:23 2011
N MskiInitLogonTicketCacheHandle: Logon Ticket cache pointer retrieved from shared memory.
N MskiInitLogonTicketCacheHandle: Workprocess runs with Logon Ticket cache.
M JrfcVmcRegisterNativesDriver o.k.
W =================================================
W === ipl_Init() called
B dbtran INFO (init_connection '<DEFAULT>' [ORACLE:700.08]):
B max_blocking_factor = 15, max_in_blocking_factor = 5,
B min_blocking_factor = 10, min_in_blocking_factor = 5,
B prefer_union_all = 0, prefer_join = 0,
B prefer_fix_blocking = 0, prefer_in_itab_opt = 1,
B convert AVG = 0, alias table FUPD = 0,
B escape_as_literal = 1, opt GE LE to BETWEEN = 0,
B select * =0x0f, character encoding = STD / <none>:-,
B use_hints = abap->1, dbif->0x1, upto->2147483647, rule_in->0,
B rule_fae->0, concat_fae->0, concat_fae_or->0
W
W Wed Aug 31 15:46:24 2011
W ITS Plugin: Path dw_gui
W ITS Plugin: Description ITS Plugin - ITS rendering DLL
W ITS Plugin: sizeof(SAP_UC) 2
W ITS Plugin: Release: 700, [7000.0.52.20050900]
W ITS Plugin: Int.version, [32]
W ITS Plugin: Feature set: [10]
W ===... Calling itsp_Init in external dll ===>
W === ipl_Init() returns 0, ITSPE_OK: OK
W =================================================
E Enqueue Info: rdisp/wp_no_enq=1, rdisp/enqname=<empty>, assume crmsys_CUS_04
E Replication is disabled
E EnqCcInitialize: local lock table initialization o.k.
E EnqId_SuppressIpc: local EnqId initialization o.k.
E EnqCcInitialize: local enqueue client init o.k.
B
B Wed Aug 31 15:46:48 2011
B table logging switched off for all clients
M
M Wed Aug 31 15:47:55 2011
M SecAudit(RsauShmInit): WP attached to existing shared memory.
M SecAudit(RsauShmInit): addr of SCSA........... = 05BD0040
M SecAudit(RsauShmInit): addr of RSAUSHM........ = 05BD07A8
M SecAudit(RsauShmInit): addr of RSAUSLOTINFO... = 05BD07E0
M SecAudit(RsauShmInit): addr of RSAUSLOTS...... = 05BD07EC
A
A Wed Aug 31 15:48:44 2011
A RFC FRFC> fallback on the central gateway crmsys sapgw04 activ
B
B Wed Aug 31 15:49:47 2011
B dbmyclu : info : my major identification is 3232288873, minor one 4.
B dbmyclu : info : Time Reference is 1.12.2001 00:00:00h GMT.
B dbmyclu : info : my initial uuid is D98FA690E8AA314D9B69930868792664.
B dbmyclu : info : current optimistic cluster level: 0
B dbmyclu : info : pessimistic reads set to 2. -
Wired and Wireless sometimes work (mostly not) after update.
So I have an issue with my network connection. It sometimes works, sometimes doesn't (mostly doesn't). This is for both wired and wireless. This started to happen a couple of days ago after an update. I had not updated for about a month prior. Prior to the update I used WICD and it worked just fine with no problems. I have no exotic hardware (ipw2200 using its firmware, dell xps gen2 notebook) and I set up everything about 6 months ago based on all the wikis. I have a dlink dir-825 router. Both wired and wireless connections work in windows every boot so it's not hardware.
I've included as much info as possible... sorry for the length.
Things I've tried:
Removing the ! from the INTERFACES=(!eth0 !eth1) in rc.conf
Removing netfs from the daemons
all the hostnames match in hosts and rc.conf
Here is my rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="local"
USEDIRECTISA="no"
TIMEZONE="America/New_York"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(acpi-cpufreq cpufreq_ondemand cpufreq_powersave cpufreq_conservative cpufreq_userspace fuse ipw2200)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="yes"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="stupendiousman"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
INTERFACES=(!eth0 !eth1)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng hal cpufreq wicd alsa crond fam bluetooth)
Here is my hosts
# /etc/hosts: static lookup table for host names
#<ip-address> <hostname.domain.org> <hostname>
127.0.0.1 localhost.localdomain localhost stupendiousman
# End of file
Here is my mkinitcpio.conf
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES=""
CRYPTO_MODULES="aes_generic aes_i586 dm_crypt xts"
# BINARIES
# This setting includes, into the CPIO image, and additional
# binaries a given user may wish. This is run first, so may
# be used to override the actual binaries used in a given hook.
# (Existing files are NOT overwritten is already added)
# BINARIES are dependancy parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in anyway. This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options,
# like so:
# FILES="/etc/modprobe.conf"
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'modload' may be used in place of 'udev', but is not recommended
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
# This setup specifies all modules in the MODULES setting above.
# No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
# This setup will autodetect all modules for your system and should
# work as a sane default
# HOOKS="base udev autodetect pata scsi sata filesystems"
# This is identical to the above, except the old ide subsystem is
# used for IDE devices instead of the new pata subsystem.
# HOOKS="base udev autodetect ide scsi sata filesystems"
# This setup will generate a 'full' image which supports most systems.
# No autodetection is done.
# HOOKS="base udev pata scsi sata usb filesystems"
# This setup assembles an pata raid array with an encrypted root FS.
# Note: See 'mkinitcpio -H raid' for more information on raid devices.
# HOOKS="base udev pata raid encrypt filesystems"
# This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev usb lvm2 filesystems"
HOOKS="base udev autodetect pata scsi sata encrypt lvm2 resume filesystems firmware"
lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI Express Root Port (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
01:00.0 VGA compatible controller: nVidia Corporation NV41.9 [GeForce Go 6800 Ultra] (rev a2)
03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705M_2 Gigabit Ethernet (rev 03)
03:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
03:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08)
03:01.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17)
03:03.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)
ifconfig returns:
[rick@stupendiousman ~]$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:12:F0:3E:CA:66
inet6 addr: fe80::212:f0ff:fe3e:ca66/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:25 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:4454 (4.3 Kb)
Interrupt:17 Base address:0x6000 Memory:dcfef000-dcfeffff
eth1 Link encap:Ethernet HWaddr 00:11:43:72:B5:96
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:18
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:280 (280.0 b) TX bytes:280 (280.0 b)
If I do a iwlist scan I get:
[rick@stupendiousman ~]$ iwlist scan
lo Interface doesn't support scanning.
eth0 No scan results
eth1 Interface doesn't support scanning.
pan0 Interface doesn't support scanning.
Here is a portion of my /var/log/wicd/wicd.log
2009/08/15 09:19:29 :: ---------------------------
2009/08/15 09:19:29 :: wicd initializing...
2009/08/15 09:19:29 :: ---------------------------
2009/08/15 09:19:29 :: wicd is version 1.6.2 436
2009/08/15 09:19:29 :: setting backend to external
2009/08/15 09:19:29 :: trying to load backend external
2009/08/15 09:19:30 :: successfully loaded backend external
2009/08/15 09:19:30 :: trying to load backend external
2009/08/15 09:19:30 :: successfully loaded backend external
2009/08/15 09:19:30 :: Automatically detected wireless interface eth0
2009/08/15 09:19:30 :: setting wireless interface eth1
2009/08/15 09:19:30 :: automatically detected wired interface eth1
2009/08/15 09:19:30 :: setting wired interface eth0
2009/08/15 09:19:30 :: setting wpa driver wext
2009/08/15 09:19:30 :: setting use global dns to False
2009/08/15 09:19:30 :: setting global dns
2009/08/15 09:19:30 :: global dns servers are None None None
2009/08/15 09:19:30 :: domain is None
2009/08/15 09:19:30 :: search domain is None
2009/08/15 09:19:30 :: setting automatically reconnect when connection drops True
2009/08/15 09:19:30 :: Setting dhcp client to 0
2009/08/15 09:19:30 :: Wireless configuration file found...
2009/08/15 09:19:30 :: Wired configuration file found...
2009/08/15 09:19:30 :: chmoding configuration files 0600...
2009/08/15 09:19:30 :: chowning configuration files root:root...
2009/08/15 09:19:30 :: Using wireless interface...eth1
2009/08/15 09:19:30 :: Using wired interface...eth0
2009/08/15 09:19:36 :: Autoconnecting...
2009/08/15 09:19:39 :: Attempting to autoconnect with wired interface...
2009/08/15 09:19:39 :: Putting interface down
2009/08/15 09:19:39 :: Releasing DHCP leases...
2009/08/15 09:19:39 :: Setting false IP...
2009/08/15 09:19:39 :: Flushing the routing table...
2009/08/15 09:19:39 :: Putting interface up...
2009/08/15 09:19:39 :: Running DHCP
2009/08/15 09:19:39 :: dhcpcd: version 5.0.6 starting
2009/08/15 09:19:39 ::
2009/08/15 09:19:39 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 09:19:39 ::
2009/08/15 09:20:09 :: dhcpcd: timed out
2009/08/15 09:20:09 ::
2009/08/15 09:20:09 :: DHCP connection failed
2009/08/15 09:20:09 :: exiting connection thread
2009/08/15 09:20:11 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 09:20:11 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 09:20:11 :: Sending connection attempt result dhcp_failed
2009/08/15 09:21:03 :: trying to load backend ioctl
2009/08/15 09:21:03 :: WARNING: python-iwscan not found, falling back to using iwlist scan.
2009/08/15 09:21:03 :: WARNING: python-wpactrl not found, falling back to using wpa_cli.
2009/08/15 09:21:03 :: trying to load backend external
2009/08/15 09:21:10 :: Putting interface down
2009/08/15 09:21:10 :: Releasing DHCP leases...
2009/08/15 09:21:10 :: Setting false IP...
2009/08/15 09:21:10 :: Flushing the routing table...
2009/08/15 09:21:10 :: Putting interface up...
2009/08/15 09:21:10 :: Running DHCP
2009/08/15 09:21:10 :: dhcpcd: version 5.0.6 starting
2009/08/15 09:21:10 ::
2009/08/15 09:21:10 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 09:21:10 ::
2009/08/15 09:21:40 :: dhcpcd: timed out
2009/08/15 09:21:40 ::
2009/08/15 09:21:40 :: DHCP connection failed
2009/08/15 09:21:40 :: exiting connection thread
2009/08/15 09:21:40 :: Sending connection attempt result dhcp_failed
2009/08/15 09:22:28 :: Putting interface down
2009/08/15 09:22:28 :: Releasing DHCP leases...
2009/08/15 09:22:28 :: Setting false IP...
2009/08/15 09:22:28 :: Flushing the routing table...
2009/08/15 09:22:28 :: Putting interface up...
2009/08/15 09:22:28 :: Running DHCP
2009/08/15 09:22:28 :: dhcpcd: version 5.0.6 starting
2009/08/15 09:22:28 ::
2009/08/15 09:22:28 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 09:22:28 ::
2009/08/15 09:22:58 :: dhcpcd: timed out
2009/08/15 09:22:58 ::
2009/08/15 09:22:58 :: DHCP connection failed
2009/08/15 09:22:58 :: exiting connection thread
2009/08/15 09:22:58 :: Sending connection attempt result dhcp_failed
2009/08/15 09:23:17 :: Daemon going down, killing wicd-monitor...
2009/08/15 09:23:17 :: Removing PID file...
2009/08/15 09:23:17 :: Shutting down...
2009/08/15 13:16:59 :: ---------------------------
2009/08/15 13:16:59 :: wicd initializing...
2009/08/15 13:16:59 :: ---------------------------
2009/08/15 13:16:59 :: wicd is version 1.6.2 436
2009/08/15 13:16:59 :: setting backend to external
2009/08/15 13:16:59 :: trying to load backend external
2009/08/15 13:17:00 :: successfully loaded backend external
2009/08/15 13:17:00 :: trying to load backend external
2009/08/15 13:17:00 :: successfully loaded backend external
2009/08/15 13:17:00 :: Automatically detected wireless interface eth0
2009/08/15 13:17:00 :: setting wireless interface eth1
2009/08/15 13:17:00 :: automatically detected wired interface eth1
2009/08/15 13:17:00 :: setting wired interface eth0
2009/08/15 13:17:00 :: setting wpa driver wext
2009/08/15 13:17:00 :: setting use global dns to False
2009/08/15 13:17:00 :: setting global dns
2009/08/15 13:17:00 :: global dns servers are None None None
2009/08/15 13:17:00 :: domain is None
2009/08/15 13:17:00 :: search domain is None
2009/08/15 13:17:00 :: setting automatically reconnect when connection drops True
2009/08/15 13:17:00 :: Setting dhcp client to 0
2009/08/15 13:17:00 :: Wireless configuration file found...
2009/08/15 13:17:00 :: Wired configuration file found...
2009/08/15 13:17:00 :: chmoding configuration files 0600...
2009/08/15 13:17:00 :: chowning configuration files root:root...
2009/08/15 13:17:00 :: Using wireless interface...eth1
2009/08/15 13:17:00 :: Using wired interface...eth0
2009/08/15 13:17:06 :: Autoconnecting...
2009/08/15 13:17:09 :: Attempting to autoconnect with wired interface...
2009/08/15 13:17:09 :: Putting interface down
2009/08/15 13:17:09 :: Releasing DHCP leases...
2009/08/15 13:17:09 :: Setting false IP...
2009/08/15 13:17:09 :: Flushing the routing table...
2009/08/15 13:17:09 :: Putting interface up...
2009/08/15 13:17:09 :: Running DHCP
2009/08/15 13:17:09 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:17:09 ::
2009/08/15 13:17:09 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:17:09 ::
2009/08/15 13:17:39 :: dhcpcd: timed out
2009/08/15 13:17:39 ::
2009/08/15 13:17:39 :: DHCP connection failed
2009/08/15 13:17:39 :: exiting connection thread
2009/08/15 13:17:41 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:17:41 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:17:41 :: Sending connection attempt result dhcp_failed
2009/08/15 13:18:10 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:18:10 :: Removing PID file...
2009/08/15 13:18:10 :: Shutting down...
2009/08/15 13:19:01 :: ---------------------------
2009/08/15 13:19:01 :: wicd initializing...
2009/08/15 13:19:01 :: ---------------------------
2009/08/15 13:19:01 :: wicd is version 1.6.2 436
2009/08/15 13:19:01 :: setting backend to external
2009/08/15 13:19:01 :: trying to load backend external
2009/08/15 13:19:02 :: successfully loaded backend external
2009/08/15 13:19:02 :: trying to load backend external
2009/08/15 13:19:02 :: successfully loaded backend external
2009/08/15 13:19:02 :: Automatically detected wireless interface eth0
2009/08/15 13:19:02 :: setting wireless interface eth1
2009/08/15 13:19:02 :: automatically detected wired interface eth1
2009/08/15 13:19:02 :: setting wired interface eth0
2009/08/15 13:19:02 :: setting wpa driver wext
2009/08/15 13:19:02 :: setting use global dns to False
2009/08/15 13:19:02 :: setting global dns
2009/08/15 13:19:02 :: global dns servers are None None None
2009/08/15 13:19:02 :: domain is None
2009/08/15 13:19:02 :: search domain is None
2009/08/15 13:19:02 :: setting automatically reconnect when connection drops True
2009/08/15 13:19:02 :: Setting dhcp client to 0
2009/08/15 13:19:02 :: Wireless configuration file found...
2009/08/15 13:19:02 :: Wired configuration file found...
2009/08/15 13:19:02 :: chmoding configuration files 0600...
2009/08/15 13:19:02 :: chowning configuration files root:root...
2009/08/15 13:19:02 :: Using wireless interface...eth1
2009/08/15 13:19:02 :: Using wired interface...eth0
2009/08/15 13:19:08 :: Autoconnecting...
2009/08/15 13:19:11 :: Attempting to autoconnect with wired interface...
2009/08/15 13:19:11 :: Putting interface down
2009/08/15 13:19:11 :: Releasing DHCP leases...
2009/08/15 13:19:11 :: Setting false IP...
2009/08/15 13:19:11 :: Flushing the routing table...
2009/08/15 13:19:11 :: Putting interface up...
2009/08/15 13:19:11 :: Running DHCP
2009/08/15 13:19:11 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:19:11 ::
2009/08/15 13:19:11 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:19:11 ::
2009/08/15 13:19:41 :: dhcpcd: timed out
2009/08/15 13:19:41 ::
2009/08/15 13:19:41 :: DHCP connection failed
2009/08/15 13:19:41 :: exiting connection thread
2009/08/15 13:19:43 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:19:43 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:19:43 :: Sending connection attempt result dhcp_failed
2009/08/15 13:30:36 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:30:36 :: Removing PID file...
2009/08/15 13:30:36 :: Shutting down...
2009/08/15 13:31:29 :: ---------------------------
2009/08/15 13:31:29 :: wicd initializing...
2009/08/15 13:31:29 :: ---------------------------
2009/08/15 13:31:29 :: wicd is version 1.6.2 436
2009/08/15 13:31:29 :: setting backend to external
2009/08/15 13:31:29 :: trying to load backend external
2009/08/15 13:31:30 :: successfully loaded backend external
2009/08/15 13:31:30 :: trying to load backend external
2009/08/15 13:31:30 :: successfully loaded backend external
2009/08/15 13:31:30 :: Automatically detected wireless interface eth0
2009/08/15 13:31:30 :: setting wireless interface eth1
2009/08/15 13:31:30 :: automatically detected wired interface eth1
2009/08/15 13:31:30 :: setting wired interface eth0
2009/08/15 13:31:30 :: setting wpa driver wext
2009/08/15 13:31:30 :: setting use global dns to False
2009/08/15 13:31:30 :: setting global dns
2009/08/15 13:31:30 :: global dns servers are None None None
2009/08/15 13:31:30 :: domain is None
2009/08/15 13:31:30 :: search domain is None
2009/08/15 13:31:30 :: setting automatically reconnect when connection drops True
2009/08/15 13:31:30 :: Setting dhcp client to 0
2009/08/15 13:31:30 :: Wireless configuration file found...
2009/08/15 13:31:30 :: Wired configuration file found...
2009/08/15 13:31:30 :: chmoding configuration files 0600...
2009/08/15 13:31:30 :: chowning configuration files root:root...
2009/08/15 13:31:30 :: Using wireless interface...eth1
2009/08/15 13:31:30 :: Using wired interface...eth0
2009/08/15 13:31:37 :: Autoconnecting...
2009/08/15 13:31:39 :: Attempting to autoconnect with wired interface...
2009/08/15 13:31:39 :: Putting interface down
2009/08/15 13:31:39 :: Releasing DHCP leases...
2009/08/15 13:31:39 :: Setting false IP...
2009/08/15 13:31:39 :: Flushing the routing table...
2009/08/15 13:31:39 :: Putting interface up...
2009/08/15 13:31:39 :: Running DHCP
2009/08/15 13:31:39 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:31:39 ::
2009/08/15 13:31:40 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:31:40 ::
2009/08/15 13:32:09 :: dhcpcd: timed out
2009/08/15 13:32:09 ::
2009/08/15 13:32:09 :: DHCP connection failed
2009/08/15 13:32:09 :: exiting connection thread
2009/08/15 13:32:12 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:32:12 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:32:12 :: Sending connection attempt result dhcp_failed
2009/08/15 13:38:00 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:38:00 :: Removing PID file...
2009/08/15 13:38:00 :: Shutting down...
2009/08/15 13:39:19 :: ---------------------------
2009/08/15 13:39:19 :: wicd initializing...
2009/08/15 13:39:19 :: ---------------------------
2009/08/15 13:39:19 :: wicd is version 1.6.2 436
2009/08/15 13:39:19 :: setting backend to external
2009/08/15 13:39:19 :: trying to load backend external
2009/08/15 13:39:20 :: successfully loaded backend external
2009/08/15 13:39:20 :: trying to load backend external
2009/08/15 13:39:20 :: successfully loaded backend external
2009/08/15 13:39:20 :: Automatically detected wireless interface eth0
2009/08/15 13:39:20 :: setting wireless interface eth1
2009/08/15 13:39:20 :: automatically detected wired interface eth1
2009/08/15 13:39:20 :: setting wired interface eth0
2009/08/15 13:39:20 :: setting wpa driver wext
2009/08/15 13:39:20 :: setting use global dns to False
2009/08/15 13:39:20 :: setting global dns
2009/08/15 13:39:20 :: global dns servers are None None None
2009/08/15 13:39:20 :: domain is None
2009/08/15 13:39:20 :: search domain is None
2009/08/15 13:39:20 :: setting automatically reconnect when connection drops True
2009/08/15 13:39:20 :: Setting dhcp client to 0
2009/08/15 13:39:20 :: Wireless configuration file found...
2009/08/15 13:39:20 :: Wired configuration file found...
2009/08/15 13:39:20 :: chmoding configuration files 0600...
2009/08/15 13:39:20 :: chowning configuration files root:root...
2009/08/15 13:39:20 :: Using wireless interface...eth1
2009/08/15 13:39:20 :: Using wired interface...eth0
2009/08/15 13:39:27 :: Autoconnecting...
2009/08/15 13:39:29 :: Attempting to autoconnect with wired interface...
2009/08/15 13:39:29 :: Putting interface down
2009/08/15 13:39:29 :: Releasing DHCP leases...
2009/08/15 13:39:29 :: Setting false IP...
2009/08/15 13:39:29 :: Flushing the routing table...
2009/08/15 13:39:29 :: Putting interface up...
2009/08/15 13:39:29 :: Running DHCP
2009/08/15 13:39:29 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:39:29 ::
2009/08/15 13:39:30 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:39:30 ::
2009/08/15 13:39:59 :: dhcpcd: timed out
2009/08/15 13:39:59 ::
2009/08/15 13:39:59 :: DHCP connection failed
2009/08/15 13:39:59 :: exiting connection thread
2009/08/15 13:40:02 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:40:02 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:40:02 :: Sending connection attempt result dhcp_failed
2009/08/15 13:45:10 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:45:10 :: Removing PID file...
2009/08/15 13:45:10 :: Shutting down...
2009/08/15 13:46:13 :: ---------------------------
2009/08/15 13:46:13 :: wicd initializing...
2009/08/15 13:46:13 :: ---------------------------
2009/08/15 13:46:13 :: wicd is version 1.6.2 436
2009/08/15 13:46:13 :: setting backend to external
2009/08/15 13:46:13 :: trying to load backend external
2009/08/15 13:46:14 :: successfully loaded backend external
2009/08/15 13:46:14 :: trying to load backend external
2009/08/15 13:46:14 :: successfully loaded backend external
2009/08/15 13:46:14 :: Automatically detected wireless interface eth1
2009/08/15 13:46:14 :: setting wireless interface eth1
2009/08/15 13:46:14 :: automatically detected wired interface eth0
2009/08/15 13:46:14 :: setting wired interface eth0
2009/08/15 13:46:14 :: setting wpa driver wext
2009/08/15 13:46:14 :: setting use global dns to False
2009/08/15 13:46:14 :: setting global dns
2009/08/15 13:46:14 :: global dns servers are None None None
2009/08/15 13:46:14 :: domain is None
2009/08/15 13:46:14 :: search domain is None
2009/08/15 13:46:14 :: setting automatically reconnect when connection drops True
2009/08/15 13:46:14 :: Setting dhcp client to 0
2009/08/15 13:46:14 :: Wireless configuration file found...
2009/08/15 13:46:14 :: Wired configuration file found...
2009/08/15 13:46:14 :: chmoding configuration files 0600...
2009/08/15 13:46:14 :: chowning configuration files root:root...
2009/08/15 13:46:14 :: Using wireless interface...eth1
2009/08/15 13:46:14 :: Using wired interface...eth0
2009/08/15 13:46:20 :: Autoconnecting...
2009/08/15 13:46:22 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:46:22 :: trying to automatically connect to...101
2009/08/15 13:46:22 :: Connecting to wireless network 101
2009/08/15 13:46:23 :: Putting interface down
2009/08/15 13:46:23 :: Releasing DHCP leases...
2009/08/15 13:46:23 :: Setting false IP...
2009/08/15 13:46:23 :: Stopping wpa_supplicant
2009/08/15 13:46:23 :: Flushing the routing table...
2009/08/15 13:46:23 :: Putting interface up...
2009/08/15 13:46:23 :: Generating psk...
2009/08/15 13:46:23 :: Attempting to authenticate...
2009/08/15 13:46:34 :: Running DHCP
2009/08/15 13:46:34 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:46:34 ::
2009/08/15 13:46:34 :: dhcpcd: eth1: broadcasting for a lease
2009/08/15 13:46:34 ::
2009/08/15 13:46:35 :: dhcpcd: eth1: offered 192.168.0.183 from 192.168.0.1
2009/08/15 13:46:35 ::
2009/08/15 13:46:35 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 13:46:35 ::
2009/08/15 13:46:35 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 13:46:35 ::
2009/08/15 13:46:38 :: dhcpcd: eth1: carrier lost
2009/08/15 13:46:38 ::
2009/08/15 13:46:40 :: dhcpcd: eth1: carrier acquired
2009/08/15 13:46:40 ::
2009/08/15 13:46:40 :: dhcpcd: eth1: broadcasting for a lease
2009/08/15 13:46:40 ::
2009/08/15 13:46:45 :: dhcpcd: eth1: offered 192.168.0.183 from 192.168.0.1
2009/08/15 13:46:45 ::
2009/08/15 13:46:45 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 13:46:45 ::
2009/08/15 13:46:45 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 13:46:45 ::
2009/08/15 13:46:51 :: dhcpcd: eth1: leased 192.168.0.183 for 86400 seconds
2009/08/15 13:46:51 ::
2009/08/15 13:46:51 :: dhcpcd: forking to background
2009/08/15 13:46:51 ::
2009/08/15 13:46:51 ::
2009/08/15 13:46:51 :: DHCP connection successful
2009/08/15 13:46:51 :: Connecting thread exiting.
2009/08/15 13:46:55 :: Sending connection attempt result Success
2009/08/15 13:48:50 :: Putting interface down
2009/08/15 13:48:50 :: Releasing DHCP leases...
2009/08/15 13:48:50 :: Setting false IP...
2009/08/15 13:48:51 :: Flushing the routing table...
2009/08/15 13:48:51 :: Putting interface up...
2009/08/15 13:48:51 :: Running DHCP
2009/08/15 13:48:51 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:48:51 ::
2009/08/15 13:48:51 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:48:51 ::
2009/08/15 13:48:51 :: dhcpcd: eth0: carrier lost
2009/08/15 13:48:51 ::
2009/08/15 13:48:53 :: dhcpcd: eth0: carrier acquired
2009/08/15 13:48:53 ::
2009/08/15 13:48:53 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:48:53 ::
2009/08/15 13:48:54 :: dhcpcd: eth0: offered 192.168.0.193 from 192.168.0.1
2009/08/15 13:48:54 ::
2009/08/15 13:48:54 :: dhcpcd: eth0: acknowledged 192.168.0.193 from 192.168.0.1
2009/08/15 13:48:54 ::
2009/08/15 13:48:54 :: dhcpcd: eth0: checking for 192.168.0.193
2009/08/15 13:48:54 ::
2009/08/15 13:49:00 :: dhcpcd: eth0: leased 192.168.0.193 for 86400 seconds
2009/08/15 13:49:00 ::
2009/08/15 13:49:00 :: dhcpcd: forking to background
2009/08/15 13:49:00 ::
2009/08/15 13:49:00 ::
2009/08/15 13:49:00 :: DHCP connection successful
2009/08/15 13:49:00 :: Connecting thread exiting.
2009/08/15 13:49:00 :: Sending connection attempt result Success
2009/08/15 13:53:46 :: Connecting to wireless network 102
2009/08/15 13:53:47 :: Putting interface down
2009/08/15 13:53:47 :: Releasing DHCP leases...
2009/08/15 13:53:47 :: Setting false IP...
2009/08/15 13:53:47 :: Stopping wpa_supplicant
2009/08/15 13:53:47 :: Flushing the routing table...
2009/08/15 13:53:47 :: Putting interface up...
2009/08/15 13:53:47 :: Generating psk...
2009/08/15 13:53:47 :: Attempting to authenticate...
2009/08/15 13:54:03 :: Running DHCP
2009/08/15 13:54:03 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:54:03 ::
2009/08/15 13:54:03 :: dhcpcd: eth1: rebinding lease of 192.168.0.183
2009/08/15 13:54:03 ::
2009/08/15 13:54:03 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 13:54:03 ::
2009/08/15 13:54:03 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 13:54:03 ::
2009/08/15 13:54:05 :: dhcpcd: eth1: carrier lost
2009/08/15 13:54:05 ::
2009/08/15 13:54:06 :: dhcpcd: eth1: carrier acquired
2009/08/15 13:54:06 ::
2009/08/15 13:54:06 :: dhcpcd: eth1: rebinding lease of 192.168.0.183
2009/08/15 13:54:06 ::
2009/08/15 13:54:06 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 13:54:06 ::
2009/08/15 13:54:06 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 13:54:06 ::
2009/08/15 13:54:11 :: dhcpcd: eth1: leased 192.168.0.183 for 86400 seconds
2009/08/15 13:54:11 ::
2009/08/15 13:54:11 :: dhcpcd: forking to background
2009/08/15 13:54:11 ::
2009/08/15 13:54:11 ::
2009/08/15 13:54:11 :: DHCP connection successful
2009/08/15 13:54:11 :: Connecting thread exiting.
2009/08/15 13:54:11 :: Sending connection attempt result Success
2009/08/15 13:55:03 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:55:03 :: Removing PID file...
2009/08/15 13:55:03 :: Shutting down...
2009/08/15 13:55:52 :: ---------------------------
2009/08/15 13:55:52 :: wicd initializing...
2009/08/15 13:55:52 :: ---------------------------
2009/08/15 13:55:52 :: wicd is version 1.6.2 436
2009/08/15 13:55:52 :: setting backend to external
2009/08/15 13:55:52 :: trying to load backend external
2009/08/15 13:55:53 :: successfully loaded backend external
2009/08/15 13:55:53 :: trying to load backend external
2009/08/15 13:55:53 :: successfully loaded backend external
2009/08/15 13:55:53 :: Automatically detected wireless interface eth0
2009/08/15 13:55:53 :: setting wireless interface eth1
2009/08/15 13:55:53 :: automatically detected wired interface eth1
2009/08/15 13:55:53 :: setting wired interface eth0
2009/08/15 13:55:53 :: setting wpa driver wext
2009/08/15 13:55:53 :: setting use global dns to False
2009/08/15 13:55:53 :: setting global dns
2009/08/15 13:55:53 :: global dns servers are None None None
2009/08/15 13:55:53 :: domain is None
2009/08/15 13:55:53 :: search domain is None
2009/08/15 13:55:53 :: setting automatically reconnect when connection drops True
2009/08/15 13:55:53 :: Setting dhcp client to 0
2009/08/15 13:55:53 :: Wireless configuration file found...
2009/08/15 13:55:53 :: Wired configuration file found...
2009/08/15 13:55:53 :: chmoding configuration files 0600...
2009/08/15 13:55:53 :: chowning configuration files root:root...
2009/08/15 13:55:53 :: Using wireless interface...eth1
2009/08/15 13:55:53 :: Using wired interface...eth0
2009/08/15 13:55:59 :: Autoconnecting...
2009/08/15 13:56:02 :: Attempting to autoconnect with wired interface...
2009/08/15 13:56:02 :: Putting interface down
2009/08/15 13:56:02 :: Releasing DHCP leases...
2009/08/15 13:56:02 :: Setting false IP...
2009/08/15 13:56:02 :: Flushing the routing table...
2009/08/15 13:56:02 :: Putting interface up...
2009/08/15 13:56:02 :: Running DHCP
2009/08/15 13:56:02 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:56:02 ::
2009/08/15 13:56:02 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 13:56:02 ::
2009/08/15 13:56:12 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:56:12 ::
2009/08/15 13:56:32 :: dhcpcd: timed out
2009/08/15 13:56:32 ::
2009/08/15 13:56:32 :: DHCP connection failed
2009/08/15 13:56:32 :: exiting connection thread
2009/08/15 13:56:34 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:56:34 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:56:34 :: Sending connection attempt result dhcp_failed
2009/08/15 13:57:31 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:57:31 :: Removing PID file...
2009/08/15 13:57:31 :: Shutting down...
2009/08/15 13:57:32 :: ---------------------------
2009/08/15 13:57:32 :: wicd initializing...
2009/08/15 13:57:32 :: ---------------------------
2009/08/15 13:57:32 :: wicd is version 1.6.2 436
2009/08/15 13:57:32 :: setting backend to external
2009/08/15 13:57:32 :: trying to load backend external
2009/08/15 13:57:32 :: successfully loaded backend external
2009/08/15 13:57:32 :: trying to load backend external
2009/08/15 13:57:32 :: successfully loaded backend external
2009/08/15 13:57:32 :: Automatically detected wireless interface eth0
2009/08/15 13:57:32 :: setting wireless interface eth1
2009/08/15 13:57:32 :: automatically detected wired interface eth1
2009/08/15 13:57:32 :: setting wired interface eth0
2009/08/15 13:57:32 :: setting wpa driver wext
2009/08/15 13:57:32 :: setting use global dns to False
2009/08/15 13:57:32 :: setting global dns
2009/08/15 13:57:32 :: global dns servers are None None None
2009/08/15 13:57:32 :: domain is None
2009/08/15 13:57:32 :: search domain is None
2009/08/15 13:57:32 :: setting automatically reconnect when connection drops True
2009/08/15 13:57:32 :: Setting dhcp client to 0
2009/08/15 13:57:32 :: Wireless configuration file found...
2009/08/15 13:57:32 :: Wired configuration file found...
2009/08/15 13:57:32 :: chmoding configuration files 0600...
2009/08/15 13:57:32 :: chowning configuration files root:root...
2009/08/15 13:57:32 :: Using wireless interface...eth1
2009/08/15 13:57:32 :: Using wired interface...eth0
2009/08/15 13:57:38 :: Autoconnecting...
2009/08/15 13:57:38 :: Putting interface down
2009/08/15 13:57:38 :: Attempting to autoconnect with wired interface...
2009/08/15 13:57:38 :: Releasing DHCP leases...
2009/08/15 13:57:38 :: Setting false IP...
2009/08/15 13:57:38 :: Flushing the routing table...
2009/08/15 13:57:38 :: Putting interface up...
2009/08/15 13:57:38 :: Running DHCP
2009/08/15 13:57:38 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:57:38 ::
2009/08/15 13:57:38 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 13:57:38 ::
2009/08/15 13:57:48 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:57:48 ::
2009/08/15 13:58:08 :: dhcpcd: timed out
2009/08/15 13:58:08 ::
2009/08/15 13:58:08 :: DHCP connection failed
2009/08/15 13:58:08 :: exiting connection thread
2009/08/15 13:58:08 :: Sending connection attempt result dhcp_failed
2009/08/15 13:58:10 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:58:10 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:58:46 :: Putting interface down
2009/08/15 13:58:46 :: Releasing DHCP leases...
2009/08/15 13:58:46 :: Setting false IP...
2009/08/15 13:58:46 :: Flushing the routing table...
2009/08/15 13:58:46 :: Putting interface up...
2009/08/15 13:58:46 :: Running DHCP
2009/08/15 13:58:46 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:58:46 ::
2009/08/15 13:58:46 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 13:58:46 ::
2009/08/15 13:58:56 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:58:56 ::
2009/08/15 13:59:16 :: dhcpcd: timed out
2009/08/15 13:59:16 ::
2009/08/15 13:59:16 :: DHCP connection failed
2009/08/15 13:59:16 :: exiting connection thread
2009/08/15 13:59:16 :: Sending connection attempt result dhcp_failed
2009/08/15 14:10:08 :: Daemon going down, killing wicd-monitor...
2009/08/15 14:10:08 :: Removing PID file...
2009/08/15 14:10:08 :: Shutting down...
2009/08/15 14:10:59 :: ---------------------------
2009/08/15 14:10:59 :: wicd initializing...
2009/08/15 14:10:59 :: ---------------------------
2009/08/15 14:10:59 :: wicd is version 1.6.2 436
2009/08/15 14:10:59 :: setting backend to external
2009/08/15 14:10:59 :: trying to load backend external
2009/08/15 14:10:59 :: successfully loaded backend external
2009/08/15 14:10:59 :: trying to load backend external
2009/08/15 14:10:59 :: successfully loaded backend external
2009/08/15 14:10:59 :: Automatically detected wireless interface eth0
2009/08/15 14:10:59 :: setting wireless interface eth1
2009/08/15 14:10:59 :: automatically detected wired interface eth1
2009/08/15 14:10:59 :: setting wired interface eth0
2009/08/15 14:10:59 :: setting wpa driver wext
2009/08/15 14:10:59 :: setting use global dns to False
2009/08/15 14:10:59 :: setting global dns
2009/08/15 14:10:59 :: global dns servers are None None None
2009/08/15 14:10:59 :: domain is None
2009/08/15 14:10:59 :: search domain is None
2009/08/15 14:10:59 :: setting automatically reconnect when connection drops True
2009/08/15 14:10:59 :: Setting dhcp client to 0
2009/08/15 14:10:59 :: Wireless configuration file found...
2009/08/15 14:10:59 :: Wired configuration file found...
2009/08/15 14:10:59 :: chmoding configuration files 0600...
2009/08/15 14:10:59 :: chowning configuration files root:root...
2009/08/15 14:10:59 :: Using wireless interface...eth1
2009/08/15 14:10:59 :: Using wired interface...eth0
2009/08/15 14:11:06 :: Autoconnecting...
2009/08/15 14:11:09 :: Attempting to autoconnect with wired interface...
2009/08/15 14:11:09 :: Putting interface down
2009/08/15 14:11:09 :: Releasing DHCP leases...
2009/08/15 14:11:09 :: Setting false IP...
2009/08/15 14:11:09 :: Flushing the routing table...
2009/08/15 14:11:09 :: Putting interface up...
2009/08/15 14:11:09 :: Running DHCP
2009/08/15 14:11:09 :: dhcpcd: version 5.0.6 starting
2009/08/15 14:11:09 ::
2009/08/15 14:11:09 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 14:11:09 ::
2009/08/15 14:11:19 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 14:11:19 ::
2009/08/15 14:11:39 :: dhcpcd: timed out
2009/08/15 14:11:39 ::
2009/08/15 14:11:39 :: DHCP connection failed
2009/08/15 14:11:39 :: exiting connection thread
2009/08/15 14:11:41 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 14:11:41 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 14:11:41 :: Sending connection attempt result dhcp_failed
2009/08/15 14:13:00 :: Daemon going down, killing wicd-monitor...
2009/08/15 14:13:00 :: Removing PID file...
2009/08/15 14:13:00 :: Shutting down...
2009/08/15 14:13:50 :: ---------------------------
2009/08/15 14:13:50 :: wicd initializing...
2009/08/15 14:13:50 :: ---------------------------
2009/08/15 14:13:50 :: wicd is version 1.6.2 436
2009/08/15 14:13:50 :: setting backend to external
2009/08/15 14:13:50 :: trying to load backend external
2009/08/15 14:13:50 :: successfully loaded backend external
2009/08/15 14:13:50 :: trying to load backend external
2009/08/15 14:13:50 :: successfully loaded backend external
2009/08/15 14:13:51 :: Automatically detected wireless interface eth1
2009/08/15 14:13:51 :: setting wireless interface eth1
2009/08/15 14:13:51 :: automatically detected wired interface eth0
2009/08/15 14:13:51 :: setting wired interface eth0
2009/08/15 14:13:51 :: setting wpa driver wext
2009/08/15 14:13:51 :: setting use global dns to False
2009/08/15 14:13:51 :: setting global dns
2009/08/15 14:13:51 :: global dns servers are None None None
2009/08/15 14:13:51 :: domain is None
2009/08/15 14:13:51 :: search domain is None
2009/08/15 14:13:51 :: setting automatically reconnect when connection drops True
2009/08/15 14:13:51 :: Setting dhcp client to 0
2009/08/15 14:13:51 :: Wireless configuration file found...
2009/08/15 14:13:51 :: Wired configuration file found...
2009/08/15 14:13:51 :: chmoding configuration files 0600...
2009/08/15 14:13:51 :: chowning configuration files root:root...
2009/08/15 14:13:51 :: Using wireless interface...eth1
2009/08/15 14:13:51 :: Using wired interface...eth0
2009/08/15 14:13:57 :: Autoconnecting...
2009/08/15 14:13:59 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 14:14:00 :: trying to automatically connect to...101
2009/08/15 14:14:00 :: Connecting to wireless network 101
2009/08/15 14:14:00 :: Putting interface down
2009/08/15 14:14:00 :: Releasing DHCP leases...
2009/08/15 14:14:00 :: Setting false IP...
2009/08/15 14:14:00 :: Stopping wpa_supplicant
2009/08/15 14:14:00 :: Flushing the routing table...
2009/08/15 14:14:00 :: Putting interface up...
2009/08/15 14:14:00 :: Generating psk...
2009/08/15 14:14:01 :: Attempting to authenticate...
2009/08/15 14:14:11 :: Running DHCP
2009/08/15 14:14:11 :: dhcpcd: version 5.0.6 starting
2009/08/15 14:14:11 ::
2009/08/15 14:14:11 :: dhcpcd: eth1: rebinding lease of 192.168.0.183
2009/08/15 14:14:11 ::
2009/08/15 14:14:11 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 14:14:11 ::
2009/08/15 14:14:11 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 14:14:11 ::
2009/08/15 14:14:15 :: dhcpcd: eth1: leased 192.168.0.183 for 86400 seconds
2009/08/15 14:14:15 ::
2009/08/15 14:14:15 :: dhcpcd: forking to background
2009/08/15 14:14:15 ::
2009/08/15 14:14:15 ::
2009/08/15 14:14:15 :: DHCP connection successful
2009/08/15 14:14:15 :: Connecting thread exiting.
2009/08/15 14:14:17 :: Sending connection attempt result Success
2009/08/15 14:14:17 :: Autoconnecting...
2009/08/15 14:14:17 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 14:14:17 :: trying to automatically connect to...102
2009/08/15 14:14:17 :: Connecting to wireless network 102
2009/08/15 14:14:17 :: Putting interface down
2009/08/15 14:14:17 :: Releasing DHCP leases...
2009/08/15 14:14:18 :: Setting false IP...
2009/08/15 14:14:18 :: Stopping wpa_supplicant
2009/08/15 14:14:18 :: Flushing the routing table...
2009/08/15 14:14:18 :: Putting interface up...
2009/08/15 14:14:18 :: Generating psk...
2009/08/15 14:14:18 :: Attempting to authenticate...
2009/08/15 14:14:19 :: Running DHCP
2009/08/15 14:14:19 :: dhcpcd: version 5.0.6 starting
2009/08/15 14:14:19 ::
2009/08/15 14:14:19 :: dhcpcd: eth1: rebinding lease of 192.168.0.183
2009/08/15 14:14:19 ::
2009/08/15 14:14:19 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 14:14:19 ::
2009/08/15 14:14:19 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 14:14:19 ::
2009/08/15 14:14:24 :: dhcpcd: eth1: leased 192.168.0.183 for 86400 seconds
2009/08/15 14:14:24 ::
2009/08/15 14:14:24 :: dhcpcd: forking to background
2009/08/15 14:14:24 ::
2009/08/15 14:14:24 ::
2009/08/15 14:14:24 :: DHCP connection successful
2009/08/15 14:14:24 :: Connecting thread exiting.
2009/08/15 14:14:29 :: Sending connection attempt result Success
2009/08/15 14:15:02 :: Daemon going down, killing wicd-monitor...
2009/08/15 14:15:02 :: Removing PID file...
2009/08/15 14:15:02 :: Shutting down...
2009/08/15 14:15:52 :: ---------------------------
2009/08/15 14:15:52 :: wicd initializing...
2009/08/15 14:15:52 :: ---------------------------
2009/08/15 14:15:52 :: wicd is version 1.6.2 436
2009/08/15 14:15:52 :: setting backend to external
2009/08/15 14:15:52 :: trying to load backend external
2009/08/15 14:15:52 :: successfully loaded backend external
2009/08/15 14:15:52 :: trying to load backend external
2009/08/15 14:15:52 :: successfully loaded backend external
2009/08/15 14:15:52 :: Automatically detected wireless interface eth0
2009/08/15 14:15:52 :: setting wireless interface eth1
2009/08/15 14:15:52 :: automatically detected wired interface eth1
2009/08/15 14:15:52 :: setting wired interface eth0
2009/08/15 14:15:52 :: setting wpa driver wext
2009/08/15 14:15:52 :: setting use global dns to False
2009/08/15 14:15:52 :: setting global dns
2009/08/15 14:15:52 :: global dns servers are None None None
2009/08/15 14:15:52 :: domain is None
2009/08/15 14:15:52 :: search domain is None
2009/08/15 14:15:52 :: setting automatically reconnect when connection drops True
2009/08/15 14:15:52 :: Setting dhcp client to 0
2009/08/15 14:15:52 :: Wireless configuration file found...
2009/08/15 14:15:52 :: Wired configuration file found...
2009/08/15 14:15:52 :: chmoding configuration files 0600...
2009/08/15 14:15:52 :: chowning configuration files root:root...
2009/08/15 14:15:52 :: Using wireless interface...eth1
2009/08/15 14:15:52 :: Using wired interface...eth0
2009/08/15 14:15:59 :: Autoconnecting...
2009/08/15 14:16:02 :: Attempting to autoconnect with wired interface...
2009/08/15 14:16:02 :: Putting interface down
2009/08/15 14:16:02 :: Releasing DHCP leases...
2009/08/15 14:16:02 :: Setting false IP...
2009/08/15 14:16:02 :: Flushing the routing table...
2009/08/15 14:16:02 :: Putting interface up...
2009/08/15 14:16:02 :: Running DHCP
2009/08/15 14:16:02 :: dhcpcd: version 5.0.6 starting
2009/08/15 14:16:02 ::
2009/08/15 14:16:02 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 14:16:02 ::
2009/08/15 14:16:12 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 14:16:12 ::
2009/08/15 14:16:32 :: dhcpcd: timed out
2009/08/15 14:16:32 ::
2009/08/15 14:16:32 :: DHCP connection failed
2009/08/15 14:16:32 :: exiting connection thread
2009/08/15 14:16:34 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 14:16:34 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 14:16:34 :: Sending connection attempt result dhcp_failed
2009/08/15 14:17:02 :: Daemon going down, killing wicd-monitor...
2009/08/15 14:17:02 :: Removing PID file...
2009/08/15 14:17:02 :: Shutting down...
2009/08/15 15:39:03 :: ---------------------------
2009/08/15 15:39:03 :: wicd initializing...
2009/08/15 15:39:03 :: ---------------------------
2009/08/15 15:39:03 :: wicd is version 1.6.2 436
2009/08/15 15:39:03 :: setting backend to external
2009/08/15 15:39:03 :: trying to load backend external
2009/08/15 15:39:03 :: successfully loaded backend external
2009/08/15 15:39:03 :: trying to load backend external
2009/08/15 15:39:03 :: successfully loaded backend external
2009/08/15 15:39:03 :: Automatically detected wireless interface eth0
2009/08/15 15:39:03 :: setting wireless interface eth1
2009/08/15 15:39:03 :: automatically detected wired interface eth1
2009/08/15 15:39:03 :: setting wired interface eth0
2009/08/15 15:39:03 :: setting wpa driver wext
2009/08/15 15:39:03 :: setting use global dns to False
2009/08/15 15:39:03 :: setting global dns
2009/08/15 15:39:03 :: global dns servers are None None None
2009/08/15 15:39:03 :: domain is None
2009/08/15 15:39:03 :: search domain is None
2009/08/15 15:39:03 :: setting automatically reconnect when connection drops True
2009/08/15 15:39:03 :: Setting dhcp client to 0
2009/08/15 15:39:03 :: Wireless configuration file found...
2009/08/15 15:39:03 :: Wired configuration file found...
2009/08/15 15:39:03 :: chmoding configuration files 0600...
2009/08/15 15:39:03 :: chowning configuration files root:root...
2009/08/15 15:39:03 :: Using wireless interface...eth1
2009/08/15 15:39:03 :: Using wired interface...eth0
2009/08/15 15:39:10 :: Autoconnecting...
2009/08/15 15:39:13 :: Attempting to autoconnect with wired interface...
2009/08/15 15:39:13 :: Putting interface down
2009/08/15 15:39:13 :: Releasing DHCP leases...
2009/08/15 15:39:13 :: Setting false IP...
2009/08/15 15:39:13 :: Flushing the routing table...
2009/08/15 15:39:13 :: Putting interface up...
2009/08/15 15:39:13 :: Running DHCP
2009/08/15 15:39:13 :: dhcpcd: version 5.0.6 starting
2009/08/15 15:39:13 ::
2009/08/15 15:39:13 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 15:39:13 ::
2009/08/15 15:39:23 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 15:39:23 ::
2009/08/15 15:39:43 :: dhcpcd: timed out
2009/08/15 15:39:43 ::
2009/08/15 15:39:43 :: DHCP connection failed
2009/08/15 15:39:43 :: exiting connection thread
2009/08/15 15:39:45 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 15:39:45 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 15:39:45 :: Sending connection attempt result dhcp_failed
2009/08/15 15:41:46 :: Daemon going down, killing wicd-monitor...
2009/08/15 15:41:46 :: Removing PID file...
2009/08/15 15:41:46 :: Shutting down...
2009/08/15 15:42:33 :: ---------------------------
2009/08/15 15:42:33 :: wicd initializing...
2009/08/15 15:42:33 :: ---------------------------
2009/08/15 15:42:33 :: wicd is version 1.6.2 436
2009/08/15 15:42:33 :: setting backend to external
2009/08/15 15:42:33 :: trying to load backend external
2009/08/15 15:42:33 :: successfully loaded backend external
2009/08/15 15:42:33 :: trying to load backend external
2009/08/15 15:42:33 :: successfully loaded backend external
2009/08/15 15:42:33 :: Automatically detected wireless interface eth0
2009/08/15 15:42:33 :: setting wireless interface eth1
2009/08/15 15:42:33 :: automatically detected wired interface eth1
2009/08/15 15:42:33 :: setting wired interface eth0
2009/08/15 15:42:33 :: setting wpa driver wext
2009/08/15 15:42:33 :: setting use global dns to False
2009/08/15 15:42:33 :: setting global dns
2009/08/15 15:42:33 :: global dns servers are None None None
2009/08/15 15:42:33 :: domain is None
2009/08/15 15:42:33 :: search domain is None
2009/08/15 15:42:33 :: setting automatically reconnect when connection drops True
2009/08/15 15:42:33 :: Setting dhcp client to 0
2009/08/15 15:42:33 :: Wireless configuration file found...
2009/08/15 15:42:33 :: Wired configuration file found...
2009/08/15 15:42:33 :: chmoding configuration files 0600...
2009/08/15 15:42:33 :: chowning configuration files root:root...
2009/08/15 15:42:33 :: Using wireless interface...eth1
2009/08/15 15:42:33 :: Using wired interface...eth0
2009/08/15 15:42:39 :: Autoconnecting...
2009/08/15 15:42:42 :: Attempting to autoconnect with wired interface...
2009/08/15 15:42:42 :: Putting interface down
2009/08/15 15:42:42 :: Releasing DHCP leases...
2009/08/15 15:42:42 :: Setting false IP...
2009/08/15 15:42:42 :: Flushing the routing table...
2009/08/15 15:42:42 :: Putting interface up...
2009/08/15 15:42:42 :: Running DHCP
2009/08/15 15:42:42 :: dhcpcd: version 5.0.6 starting
2009/08/15 15:42:42 ::
2009/08/15 15:42:42 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 15:42:42 ::
2009/08/15 15:42:52 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 15:42:52 ::
2009/08/15 15:43:12 :: dhcpcd: timed out
2009/08/15 15:43:12 ::
2009/08/15 15:43:12 :: DHCP connection failed
2009/08/15 15:43:12 :: exiting connection thread
2009/08/15 15:43:14 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 15:43:14 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 15:43:14 :: Sending connection attempt result dhcp_failed
2009/08/15 15:44:27 :: Daemon going down, killing wicd-monitor...
2009/08/15 15:44:27 :: Removing PID file...
2009/08/15 15:44:27 :: Shutting down...
2009/08/15 15:44:48 :: ---------------------------
2009/08/15 15:44:48 :: wicd initializing...
2009/08/15 15:44:48 :: ---------------------------
2009/08/15 15:44:48 :: wicd is version 1.6.2 436
2009/08/15 15:44:48 :: setting backend to external
2009/08/15 15:44:48 :: trying to load backend external
2009/08/15 15:44:48 :: successfully loaded backend external
2009/08/15 15:44:48 :: trying to load backend external
2009/08/15 15:44:48 :: successfully loaded backend external
2009/08/15 15:44:48 :: Automatically detected wireless interface eth0
2009/08/15 15:44:48 :: setting wireless interface eth1
2009/08/15 15:44:48 :: automatically detected wired interface eth1
2009/08/15 15:44:48 :: setting wired interface eth0
2009/08/15 15:44:48 :: setting wpa driver wext
2009/08/15 15:44:48 :: setting use global dns to False
2009/08/15 15:44:48 :: setting global dns
2009/08/15 15:44:48 :: global dns servers are None None None
2009/08/15 15:44:48 :: domain is None
2009/08/15 15:44:48 :: search domain is None
2009/08/15 15:44:48 :: setting automatically reconnect when connection drops True
2009/08/15 15:44:48 :: Setting dhcp client to 0
2009/08/15 15:44:48 :: Wireless configuration file found...
2009/08/15 15:44:48 :: Wired configuration file found...
2009/08/15 15:44:48 :: chmoding configuration files 0600...
2009/08/15 15:44:48 :: chowning configuration files root:root...
2009/08/15 15:44:48 :: Using wireless interface...eth1
2009/08/15 15:44:48 :: Using wired interface...eth0
2009/08/15 15:44:58 :: trying to load backend ioctl
2009/08/15 15:44:58 :: WARNING: python-iwscan not found, falling back to using iwlist scan.
2009/08/15 15:44:58 :: WARNING: python-wpactrl not found, falling back to using wpa_cli.
2009/08/15 15:44:58 :: trying to load backend external
2009/08/15 15:45:57 :: Autoconnecting...
2009/08/15 15:45:57 :: Putting interface down
2009/08/15 15:45:57 :: Attempting to autoconnect with wired interface...
2009/08/15 15:45:57 :: Releasing DHCP leases...
2009/08/15 15:45:57 :: Setting false IP...
2009/08/15 15:45:57 :: Flushing the routing table...
2009/08/15 15:45:57 :: Putting interface up...
2009/08/15 15:45:57 :: Running DHCP
2009/08/15 15:45:57 :: dhcpcd: version 5.0.6 starting
2009/08/15 15:45:57 ::
2009/08/15 15:45:57 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 15:45:57 ::
2009/08/15 15:46:07 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 15:46:07 ::
2009/08/15 15:46:27 :: dhcpcd: timed out
2009/08/15 15:46:27 ::
2009/08/15 15:46:27 :: DHCP connection failed
2009/08/15 15:46:27 :: exiting connection thread
2009/08/15 15:46:29 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 15:46:29 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 15:46:29 :: Sending connection attempt result dhcp_failedWas able to boot this weekend and did an update which updated the kernel. Rebooted and there was no network. Rebooted again and no network... rebooted again and... had network!? I tried changing wicd to use dhclient only and did the triple reboot test again and it didn't change anything... randomly working network... same with dhcpcd.
So it appears to be a dhcp timeout issue however it makes no sense because before the update a couple weeks ago it was working every time with no hiccup. Am I not providing enough information that will aid in anyone helping me figure this out? -
Is in PI7.1 possible asynchronous communication between SOAP and ABAPProxy?
Hi,
when method execute_asynchronous has disapeared since XI/PI 7.1, is
there still way how to use ABAP proxy in asynchronous way?
We need to build asynchronous connection SOAP->PI->ABAP_Proxy.
In PI, both interfaces are defined as asynchronous (outbound for SOAP and
inbound for ABAP Proxy).
Despite of this fact, when message is sent, it is processed
synchronous way.
I have set breakpoint in my implementation of method for ABAP Proxy
message processing. When message is sent and breakpoint is reached,
whole connection stays open (between SOAP and PI and between PI and
ABAP Proxy) and waits for processing method (the breakpointed one) to
return. Only when processing method returns, is connection finelly
closed.
If i understand it correctly, this is synchronous behavior. In
asynchronous behavior, as i understand it, should be connection
between PI and ABAP Proxy of application server closed immediately
after message has been delivered. This mean before my processing
method is even called.
The same could be said about SOAP and PI communication. Connection
should be closed immediately after PI has received message. From
definition of asynchronous communication of PI is obvious, that PI
should receive message correctly and close connection to sender system
even when receiver is unreachable. It should deliver message later
when, receiver system is back on line. So why it keeps connection to
sender system open while it waits for receiver?
Why is this happening, when both interfaces are defined as
asynchronous? Could be the reason for this, if APPLICATION
ACKNOWLEDGEMENT is set on by default? If so, how can i change it
to SYSTEM ACKNOWLEDGEMENT, or disable it at all?
Or is this kind of asynchronous communication even possible since
XI/PI 7.1 ?
Processing of message we are sending can take some time, so we dont
want connection pending open while waiting for finish of
processing. Thats the reason why we have chose asynchronous model to
use.Quote from How to Use the J2EE SOAP Adapter:
"If you select Best Effort, the Web service client will receive a response
message in the SOAP body. Otherwise, the Web service client will not receive a
response message if no error occurs."
"if no error occurs" - that is the problem. In either case he still
waits if some error occure or not. I dont want it. Once PI has
received message, I want the connection with sender to be closed. If
there will be error in communication between PI and reciever, I want
to see it only in PI log. That mean no notification to sender to be
send about that error.
Is that possible? -
How to set up WRT54GS so the wired and wireless connections both work?
I have a DSL line in to a Motorola modem.
The modem is connected to the WRT54GS with an ethernet cable.
When I connect my computers directly into the WRT54GS with an ethernet cable (there are four connection spots at the back of the box), I cannot go to the internet. I have 3 computers plugged in, but none of them connect via Ethernet..
Is there a setting on the router so that I can use the router for both wired and wireless connectivity?
Added info: I tried to connect directly from the computer to the modem, but again, got no connectivity. When I "chatted" with ATT, they told me the modem is set to "bridge", and that I could connect only one device. I don't want to change this setting because I want to use the router for the wireless capability. Besides which, I have more than one computer to connect to the internet.
How come I cannot just plug in and go?
My firmware version is v2.07.1.
I don't know how to find out what hardware version I have.
Other info is "DirectEthernet Connection, Speed: 100.0 Mbps, Signal Strength: Excellent, Status: Connected"
Also "1394 Connection 3, Speed: 400.0 Mbps, Status: Connected"
I don't know what that's for, but thought it might prove useful to those of you who are knowledgeable about such things.
Wireless is ok, but if I'm sitting right next to the router, I'd like to connect with Ethernet and take advantage of the better speed, etc.
Thanks in advance.Just click this link.
-
Communication between jsp and abstractportalcomponent
Hello All
Communication between jsp and abstractPortalComponent.
jsp contains one input text field and one submit button.
when the user clicks on submit button it will call the component and that input value will
display in same jsp page.
how this communication will happen?
Rgrds
SriHi Srikanth,
In the JAVA File,
OnSubmit Event,
String inputvalue ;
InputField myInputField = (InputField) getComponentByName("Input_Field_ID");
if (myInputField != null) {
inputvalue = myInputField.getValueAsDataType().toString();
request.putValue("textvalue", inputvalue);
request is IPORTALCOMPONENTREQUEST Object.
In JSP File, to retreive the value,
<%
String textstring = (String) ComponentRequest.getValue("textvalue");
%>
In PORTALAPP.XML File,
<component name="component name">
<component-config>
<property name="ClassName" value="classname"/>
<property name="SafetyLevel" value="no_safety"/>
</component-config>
<component-profile>
<property name="tagLib" value="/SERVICE/htmlb/taglib/htmlb.tld"/>
</component-profile>
</component>
Using the code above, You can pass and read values between abstract portal component and Jsp Page.
Instead of this, I suggest you to use JSPDYNPAGE Component for Data Exchange.
Check the [Link|http://help.sap.com/saphelp_nw2004s/helpdata/de/ce/e0a341354ca309e10000000a155106/frameset.htm].
Hope this helps you.
Regards,
Eben Joyson -
COMMUNICATION BETWEEN JAVASCRIPT AND JAVA APPLET: US$20 AWARD FOR SOLUTION!
COMMUNICATION BETWEEN JAVASCRIPT AND JAVA APPLET PROBLEM (Easy Filter Java Applet) -
US$20 TO ANYONE WHO CAN RESOLVE THE PROBLEM
To forum visitors:
I am prepared to pay a standard shareware fee of US$20 to a user who can resolve this technical problem.
If your advice resolves the problem, I'll forward the payment to your postal address (include your
address with your reply, and also your email address)
I am attempting to enable a HTML button (using Javascript's onClick command) to directly input a number into one of the parameter text boxes in the Easy Filter Java applet (ie, enter a new color value number in the text field of the standard Colors Multiplicator Filter interface).
The applet is Freeware and can be downloaded at: http://www.javazoom.net/applets/easyfilter10/EasyFilter10.html
(It is a very effective bitmap display and editing utility)
To achieve this, I am trying to access the part of the applet that defines and sets the textbox. The text box is defined in the .class file by accessing the parameter details in the genericfilter.txt file (accompanies the .class files). I need to access 'private String appletInitialize()' and then one of the 'textFieldParameters' which sets the textbox.
I understand the basic syntax for referencing the applet:
document.appletname.setString("An example"). However, accessing the text fields in this applet is more complex!!
Please can you recommend the correct Javascript syntax to achieve communication with the applet.
Thank you for your kind assistance.
JM Graham
[email protected]
The Java source code for the applet: EasyFilter.class
# Easy Filter - E.B/JavaZOOM 1999 #
# Contact: [email protected] #
# http://javazoom.hypermart.net #
/* Originally compiled from EasyFilter.java */
import java.awt.*;
import java.io.*;
import java.net.*;
import java.applet.Applet;
import java.awt.event.KeyEvent;
import java.awt.event.KeyListener;
import java.awt.image.MemoryImageSource;
import java.awt.image.PixelGrabber;
import java.util.Vector;
public synchronized class EasyFilter extends Applet implements KeyListener
private String paramFileName;
private Color bgColor;
private Color fgColor;
private Color parColor;
private Color sepColor;
private Color titleColor;
private Color helpColor;
private int WinWidth;
private int WinHeight;
private String title;
private String logoFileName;
private String originalImageFileName;
private String filteredCaption;
private String originalCaption;
private Vector paramsName;
private Vector paramsValue;
private Vector paramsComment;
private Panel panelParameters[];
private Label labelParameters[];
private TextField textFieldParameters[];
private Label labelComments[];
private int nbParameters;
private ScrollPane scrollPaneParams;
private Panel panelParams;
private Image theLogo;
private Image theOriginalImage;
private Image theFilteredImage;
private int theOriginalPixelArray[];
private int logoWidth;
private int logoHeight;
private int imageWidth;
private int imageHeight;
private drawCanvas canvasTitle;
private Panel panelTitle;
private Label labelTitle;
private Panel panelImages;
private Panel panelOriginalImage;
private drawCanvas canvasOriginalImage;
private Label labelOriginalImage;
private Panel panelFilteredImage;
private drawCanvas canvasFilteredImage;
private Label labelFilteredImage;
private Panel panelHelp;
private Label labelHelp;
private int Yspc;
private FilterImplementation theFilter;
public void init()
String string = null;
string = appletInitialize();
setBackground(bgColor);
if (string != null)
removeAll();
setBackground(Color.white);
setForeground(Color.black);
Label label = new Label(new StringBuffer("Error: ").append(string).toString(), 1);
Panel panel = new Panel();
panel.add(label);
add(panel);
setLayout(new FlowLayout(1, 5, Yspc));
public void keyPressed(KeyEvent keyEvent)
panelHelp.removeAll();
boolean flag = true;
if (KeyEvent.getKeyText(keyEvent.getKeyCode()).equals("Enter"))
for (int i = 0; i < nbParameters; )
try
paramsValue.setElementAt(new Double(textFieldParameters.getText()), i);
i++;
catch (NumberFormatException e)
labelHelp.setText(labelParameters[i].getText() + ": Not a Number");
flag = false;
break;
if (flag == 1)
labelHelp.setText(" .... Running, please wait .... ");
labelHelp.setAlignment(1);
panelHelp.add(labelHelp);
panelHelp.doLayout();
theFilter.updateParameters(paramsValue);
theFilter.computeFilter();
theFilteredImage = createImage(new MemoryImageSource(theFilter.getFinalImageWidth(), theFilter.getFinalImageHeight(), theFilter.getFinalImageBuffer(), 0, theFilter.getFinalImageWidth()));
canvasFilteredImage.setImage(theFilteredImage);
canvasFilteredImage.setBounds(0, 0, theFilter.getFinalImageWidth(), theFilter.getFinalImageHeight());
canvasFilteredImage.repaint();
panelHelp.removeAll();
labelHelp.setText("- Done -");
else
labelHelp.setText("- Press Enter to run the Filter -");
labelHelp.setAlignment(1);
panelHelp.add(labelHelp);
panelHelp.doLayout();
public void keyReleased(KeyEvent keyEvent)
public void keyTyped(KeyEvent keyEvent)
private String appletInitialize()
WinWidth = size().width;
WinHeight = size().height;
if (getParameter("bgcolor") == null)
bgColor = new Color(0, 0, 40);
else
bgColor = new Color(Integer.parseInt(getParameter("bgcolor"), 16));
if (getParameter("fgcolor") == null)
fgColor = new Color(255, 255, 255);
else
fgColor = new Color(Integer.parseInt(getParameter("fgcolor"), 16));
if (getParameter("sepcolor") == null)
sepColor = new Color(158, 128, 128);
else
sepColor = new Color(Integer.parseInt(getParameter("sepcolor"), 16));
if (getParameter("parcolor") == null)
parColor = new Color(24, 24, 24);
else
parColor = new Color(Integer.parseInt(getParameter("parcolor"), 16));
if (getParameter("titlecolor") == null)
titleColor = new Color(255, 255, 0);
else
titleColor = new Color(Integer.parseInt(getParameter("titlecolor"), 16));
if (getParameter("helpcolor") == null)
helpColor = new Color(0, 255, 255);
else
helpColor = new Color(Integer.parseInt(getParameter("helpcolor"), 16));
paramsName = new Vector();
paramsValue = new Vector();
paramsComment = new Vector();
paramFileName = getParameter("paramfile");
String string = readParams(paramFileName);
if (string != null)
return string;
MediaTracker mediaTracker = new MediaTracker(this);
theOriginalImage = getImage(getDocumentBase(), originalImageFileName);
mediaTracker.addImage(theOriginalImage, 0);
if (logoFileName != null)
theLogo = getImage(getDocumentBase(), logoFileName);
mediaTracker.addImage(theLogo, 1);
try
mediaTracker.waitForAll();
catch (InterruptedException e1)
return "Error while loading image";
if (mediaTracker.isErrorAny())
return "Error while loading image";
if (logoFileName != null)
logoWidth = theLogo.getWidth(this);
logoHeight = theLogo.getHeight(this);
imageWidth = theOriginalImage.getWidth(this);
imageHeight = theOriginalImage.getHeight(this);
theOriginalPixelArray = new int[imageWidth * imageHeight];
PixelGrabber pixelGrabber = new PixelGrabber(theOriginalImage, 0, 0, imageWidth, imageHeight, theOriginalPixelArray, 0, imageWidth);
try
pixelGrabber.grabPixels();
panelTitle = new Panel();
canvasTitle = new drawCanvas();
labelTitle = new Label();
panelTitle.setLayout(new FlowLayout(1, 10, Yspc));
add(panelTitle);
panelTitle.setBackground(bgColor);
panelTitle.add(canvasTitle);
canvasTitle.setImage(theLogo);
canvasTitle.setBounds(0, 0, logoWidth, logoHeight);
labelTitle.setText(title);
catch (InterruptedException e2)
return "Internal Error, Try RELOAD !";
if (title != null)
panelTitle.add(labelTitle);
labelTitle.setForeground(titleColor);
labelTitle.setFont(new Font("Dialog", 1, 14));
panelImages = new Panel();
panelOriginalImage = new Panel();
canvasOriginalImage = new drawCanvas();
labelOriginalImage = new Label();
panelFilteredImage = new Panel();
canvasFilteredImage = new drawCanvas();
labelFilteredImage = new Label();
panelImages.setLayout(new FlowLayout(1, 10, Yspc));
add(panelImages);
panelImages.setBackground(bgColor);
panelOriginalImage.setLayout(new BorderLayout(0, 2));
panelImages.add(panelOriginalImage);
panelOriginalImage.setBackground(Color.black);
panelOriginalImage.add("Center", canvasOriginalImage);
canvasOriginalImage.setImage(theOriginalImage);
canvasOriginalImage.setBounds(0, 0, imageWidth, imageHeight);
labelOriginalImage.setText(originalCaption);
labelOriginalImage.setAlignment(1);
panelOriginalImage.add("South", labelOriginalImage);
labelOriginalImage.setBackground(Color.lightGray);
labelOriginalImage.setForeground(Color.black);
labelOriginalImage.setFont(new Font("SansSerif", 0, 10));
panelFilteredImage.setLayout(new BorderLayout(0, 2));
panelImages.add(panelFilteredImage);
panelFilteredImage.setBackground(Color.black);
panelFilteredImage.add("Center", canvasFilteredImage);
theFilter = new FilterImplementation(paramsValue, theOriginalPixelArray, imageWidth, imageHeight);
theFilter.computeFilter();
theFilteredImage = createImage(new MemoryImageSource(theFilter.getFinalImageWidth(), theFilter.getFinalImageHeight(), theFilter.getFinalImageBuffer(), 0, theFilter.getFinalImageWidth()));
canvasFilteredImage.setImage(theFilteredImage);
canvasFilteredImage.setBounds(0, 0, theFilter.getFinalImageWidth(), theFilter.getFinalImageHeight());
labelFilteredImage.setText(filteredCaption);
labelFilteredImage.setAlignment(1);
panelFilteredImage.add("South", labelFilteredImage);
labelFilteredImage.setBackground(Color.lightGray);
labelFilteredImage.setFont(new Font("SansSerif", 0, 10));
scrollPaneParams = new ScrollPane(0);
panelParams = new Panel();
nbParameters = paramsName.size();
int i = WinHeight - (33 + 7 * Yspc + logoHeight + imageHeight + 23);
if (i < Yspc + 2 + 24)
i = Yspc + 2 + 24;
scrollPaneParams.setBounds(0, 0, WinWidth - 10, i);
panelParams.setLayout(new GridLayout(nbParameters, 1, 5, Yspc / 2));
scrollPaneParams.add(panelParams);
panelParams.setBackground(sepColor);
panelParameters = new Panel[nbParameters];
labelParameters = new Label[nbParameters];
textFieldParameters = new TextField[nbParameters];
labelComments = new Label[nbParameters];
for (int j = 0; j < nbParameters; j++)
panelParameters[j] = new Panel();
panelParameters[j].setLayout(new FlowLayout(0, 5, 1));
panelParams.add(panelParameters[j]);
panelParameters[j].setBackground(parColor);
labelParameters[j] = new Label();
labelParameters[j].setText((String)paramsName.elementAt(j));
panelParameters[j].add(labelParameters[j]);
labelParameters[j].setForeground(fgColor);
labelParameters[j].setFont(new Font("Dialog", 1, 12));
textFieldParameters[j] = new TextField(8);
textFieldParameters[j].setText(paramsValue.elementAt(j).toString());
panelParameters[j].add(textFieldParameters[j]);
textFieldParameters[j].setBackground(fgColor);
textFieldParameters[j].addKeyListener(this);
labelComments[j] = new Label();
labelComments[j].setText((String)paramsComment.elementAt(j));
panelParameters[j].add(labelComments[j]);
labelComments[j].setForeground(fgColor);
add(scrollPaneParams);
panelHelp = new Panel();
labelHelp = new Label();
panelHelp.setLayout(new FlowLayout(1, 5, 0));
add(panelHelp);
panelHelp.setBackground(bgColor);
labelHelp.setText(" Change colour values and press enter ");
labelHelp.setAlignment(1);
panelHelp.add(labelHelp);
labelHelp.setForeground(helpColor);
return null;
private String readParams(String string1)
Object object1;
String string2;
if (string1 == null)
return "Filename of filter's parameters needed";
try
URL uRL = new URL(getDocumentBase(), string1);
URLConnection uRLConnection = uRL.openConnection();
uRLConnection.setDoInput(true);
uRLConnection.setUseCaches(false);
BufferedReader bufferedReader = new BufferedReader(new InputStreamReader(uRLConnection.getInputStream()));
string2 = null;
catch ()
return object1.getMessage();
catch ()
return object1.getMessage();
catch ()
return object1.getMessage();
if (bufferedReader != null)
Object object2;
try
for (object2 = bufferedReader.readLine(); object2 != null && string2 == null; object2 = bufferedReader.readLine())
string2 = extractFormat(object2);
catch ()
string2 = object2.getMessage();
finally
bufferedReader.close();
if (string2 != null)
return string2;
else
return null;
private String extractFormat(String string1)
if (string1.length() == 0)
return null;
int i = 0;
int j = string1.indexOf(" ", i);
if (j == -1)
return "Bad format error (space missing)";
String string2 = string1.substring(i, j);
if (string2.equals("TITLE"))
i = j;
j = string1.indexOf(34, i);
if (j == -1)
return "Bad format (Double quote in TITLE missing)";
i = j + 1;
j = string1.indexOf(34, i);
if (j == -1)
return "Bad format (Double quote in TITLE missing)";
title = string1.substring(i, j);
return null;
if (string2.equals("ORIGINALCAPTION"))
i = j;
j = string1.indexOf(34, i);
if (j == -1)
return "Bad format (Double quote in ORIGINALCAPTION missing)";
i = j + 1;
j = string1.indexOf(34, i);
if (j == -1)
return "Bad format (Double quote in ORIGINALCAPTION missing)";
originalCaption = string1.substring(i, j);
return null;
if (string2.equals("FILTEREDCAPTION"))
i = j;
j = string1.indexOf(34, i);
if (j == -1)
return "Bad format (Double quote in FILTEREDCAPTION missing)";
i = j + 1;
j = string1.indexOf(34, i);
if (j == -1)
return "Bad format (Double quote in FILTEREDCAPTION missing)";
filteredCaption = string1.substring(i, j);
return null;
if (string2.equals("LOGO"))
i = j + 1;
j = string1.length();
logoFileName = string1.substring(i, j);
return null;
if (string2.equals("ORIGINALIMAGE"))
i = j + 1;
j = string1.length();
originalImageFileName = string1.substring(i, j);
return null;
if (!string2.equals("PARAM"))
return null;
i = j;
j = string1.indexOf(34, i);
if (j == -1)
return "Bad format in a PARAM line";
i = j + 1;
j = string1.indexOf(34, i);
if (j == -1)
return "Bad format in a PARAM line";
paramsName.addElement(string1.substring(i, j));
i = j + 2;
j = string1.indexOf(32, i);
if (j == -1)
return "Bad format in a PARAM line";
try
paramsValue.addElement(new Double(string1.substring(i, j)));
j = string1.indexOf(34, i);
catch (NumberFormatException e)
return "Bad format in a PARAM line";
if (j == -1)
return "Bad format (Double quote in PARAM comment missing)";
i = j + 1;
j = string1.indexOf(34, i);
if (j == -1)
return "Bad format (Double quote in PARAM comment missing)";
paramsComment.addElement(string1.substring(i, j));
return null;
public EasyFilter()
logoHeight = 33;
Yspc = 5;Addition to my above submission
To clarify, I'll offer the US$20 to the FIRST person who offers me a workable solution to the problem, not to everyone!!!
JMGRAHAM -
Communication between SAP and 3rd Party Systems using IDOC HTTP XML Interfa
Hi
i am try do
Communication between SAP and 3rd Party Systems using IDOC HTTP XML Interface
With The help of SDN Contribution
link----
( have look on it)
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/4943f2b7-0a01-0010-37af-faff35b2f08c
I am getting error in
Partner system as HTTPLOG and "Execute" to check the results
Error is -- Port could not be created
RFC destination HTTPLOG Not specified for system HTTPLOG
any 1 have any idea if plzzzzzzzz...........
Thank u
RamHello .
we are also in process of implementing the same
could you share the knowledge pl?
1)is it a separate add on with ALE to saphr
or using ECC ??
2)can u share the configuration part ??
we are trying it on webas as addon 3.0 .
Maybe you are looking for
-
I'm having an issue where the display fails after boot, and displays only a fixed noise pattern. The screen looks completely normal through POST, GRUB, and when initially loading the kernel, when the display is still in a text mode. After that, the s
-
SEM BPS locking even after user switches to a new variable value
Hi, This is locking related question & appreciate any kind of suggestion. Users are locking previously planned variable value even after changing to a new value which is causing another user with a locking issue. I've a variable GROUP defined at pla
-
Mac os 10.4 on dvd, need to make cd's
I have found a dvd with the mac 10.4 os but my old g3 does not have a dvd drive. I do not have another mac to use to start it. I was wanting to know if I load the dvd to my pc, can I divide it up into smaller segments to write to cd to be able to loa
-
I have a Mac Powerbook G4, running OS X 10.5.8. I'm getting messages from Google that Firefox is an old version and needs updating - so I went to the Firefox website and the message said that "Unfortunately the latest version of Firefox isn't compati
-
Access database/ java application/ jdbc odbc
i am building an access database with a java application and get the following error message when i try to run the application. the log in window that i have does not have a password text field, only a field for the odbc name. java.sql.SQLException: