DPS backend configuration question

In DPS 5.2, the storage of the rules were put in the configuration instance of the directory server you installed with DPS. We were able to then have multiple DPS servers read that same configuration from that same instance so we could do configuration in one place. Now going to 6.3, where are the rules stored? They don't appear to be in the ads instance. Is everything only in the conf.ldif? Does that mean if I have 4 DPS servers and want to make a configuration change, that I need to make it in 4 places? Or do I make the change in 1 and then use the GUI to copy the configuration to the others? Thanks in advance.

DPS 6.x and 7.x no longer use a LDAP directory to store the configuration.
DPS instance config is made of
- conf.ldif
- the keystores in <instance_path>/alias containing ssl certs + encryption key used to encrypt sensitive data in conf.ldif
- optionally pass.txt file in <instance_path>/etc containing offuscated password to protect keystores.
It is therefore possible to "clone" instances by copying these 3 file sets all together.
However, the recomended and supported procedure is to use the copy_config feature provided by the GUI.
Hope this helps
-Sylvain

Similar Messages

DPS 6.3 backend configuration

Hello all,
I've got some problems when I tried to configure datasources with dps6.3 .
I've created 2 dps running at different servers but the same configuration.
Interestingly, one of the dps shows the operational status of the datasources as "*Could Not Retrieve Status*", the other one as "*Available*" .
This remains even when the config of both dps is created from scratch with the same commands / actions in dscc.
But both dps log "*LDAP server ldap1.abc.org:637/ is up and running*." in the error-log.
I attached the backend-servers to the defaultDataSourcePool, but this didn't change anything.
By the way:
I' ve disabled the non-ssl port of all the backend servers. Anyway, I had to declare it at the creation of the datasources.
Afterwards the data-sources are listed with their non-ssl port, e.g. ldap1.abc.org:390 , but the dps is configured to use alway ssl to the backends.
Does anybody have a glue for the different state of the datasources?
Additionally, both servers log the following int the dps error-log (mgs-source: backend):
Can't retrieve LDAP schema (LDAP error code: 32) No data view were found to process the search request.
So I've checked the access-log for cn=schema, but could not find anything. But I'm not sure if backend connections will be listed here.
How to get rid of this message? The attachment of the datasources tho the defaultDataSourcePool didn't help.
Edited by: go_insane on Aug 25, 2008 2:55 AM

UPDATE:
The msg 'Could Not Retrieve Status' is no more. It seemed to be caused by use of non-fqdn of the registered servers.
Anyway, the issue with the data view for the ldap schema still exists:
"*Can't retrieve LDAP schema (LDAP error code: 32) No data view were found to process the search request.*"
How has a dataview to be configured to get rid of the message?

SAP-JEE, SAP_BUILDT, and SAP_JTECHS and Dev Configuration questions

Hi experts,
I am configuring NWDI for our environment and have a few questions that I'm trying to get my arms around.
I've read we need to check-in SAP-JEE, SAP_BUILDT, and SAP_JTECHS as required components, but I'm confused on the whole check-in vs. import thing.
I placed the 3 files in the correct OS directory and checked them in via the check-in tab on CMS.   Next, the files show up in the import queue for the DEV tab. My questions are what do I do next?
1. Do I import them into DEV? If so, what is this actually doing? Is it importing into the actual runtime system (i.e. DEV checkbox and parameters as defined in the landscape configurator for this track)? Or is just importing the file into the DEV buildspace of NWDI system?
2. Same question goes for the Consolidation tab.    Do I import them in here as well?
3. Do I need to import them into the QA and Prod systems too? Or do I remove them from the queue?
Development Configuration questions ***
4. When I download the development configuration, I can select DEV or CON workspace. What is the difference? Does DEV point to the sandbox (or central development) runtime system and CONS points to the configuration runtime system as defined in the landscape configurator? Or is this the DEV an CON workspace/buildspace of the NWDI sytem.
5. Does the selection here dictate the starting point for the development? What is an example scenarios when I would choose DEV vs. CON?
6. I have heard about the concept of a maintenance track and a development track. What is the difference and how do they differ from a setup perspective?   When would a Developer pick one over the over?
Thanks for any advice
-Dave

Hi David,
"Check-In" makes SCA known to CMS, "import" will import the content of the SCAs into CBS/DTR.
1. Yes. For these three SCAs specifically (they only contain buildarchives, no sources, no deployarchives) the build archives are imported into the dev buildspace on CBS. If the SCAs contain deployarchives and you have a runtime system configured for the dev system then those deployarchives should get deployed onto the runtime system.
2. Have you seen /people/marion.schlotte/blog/2006/03/30/best-practices-for-nwdi-track-design-for-ongoing-development ? Sooner or later you will want to.
3. Should be answered indirectly.
4. Dev/Cons correspond to the Dev/Consolidation system in CMS. For each developed SC you have 2 systems with 2 workspaces in DTR for each (inactive/active)
5. You should use dev. I would only use cons for corrections if they can't be done in dev and transported. Note that you will get conflicts in DTR if you do parallel changes in dev and cons.
6. See link in No.2 ?
Regards,
Marc

Why "backend configuration" at monitoring portal disabled

Hi!
We have an MI 7.1 newly installed.
At URL: http://FQDN:8000/sap/.../sdoe_administration, the link configuration->backend configuration
is disabled and no body can edit anything.
Is this a role issue? We granted all SAP_DOE* roles already.
Thanks!

Hi Jennifer,
Please ensure the following:
1. User Comparison is Executed for all the SAP_DOE_* Roles.
2. The User who has all SAP_DOE_* role is logging into the NW Admin Portal.
Sometimes, Portal Login asks for a login in the form of pop-up which mite result in accidentally typing user who does not have sufficient rights [ roles ].
Also, Do let us know the version of SP used at your end and the process used to setup the Server.
Best Regards, Suresh BJ

Configuration question on css11506

Hi
One of our vip with 4 local servers, currently has https. the http is redirected to https.
Now, my client has problem which a seriel directories need use http, not https. some thing like. quistion:
     1. If there is any possible, I can configure the vip to filter the special directories and let them to use http not https. and rest pages and directories redirect to https?
     2. If not, I can make another vip to use same local servers, but, is possible to only limited to special directories? and with wild code? some like the directories are partially wild coded, something like, http://web.domain/casedir*/casenumber?
     3. if not on both option, is any way I can fix this problem?
Any comments will be appreciated
Thanks in advance
Julie

I run my Tangosol cluster with 12 nodes on 3
machines(each machine with 4 cache server nodes). I
have 2 important configuration questions. Appreciate
if you can answer them ASAP.
- My requirement is that I need only 10000 objects to
be in cluster so that the resources can be freed upon
when other caches are loaded. I configured the
<high-units> to be 10000 but I am not sure if this is
per node or for the whole cluster. I see that the
total number of objects in the cluster goes till
15800 objects even when I configured for the 10K as
high-units (there is some free memory on servers in
this case). Can you please explain this?
It is per backing map, which is practically per node in case of distributed caches.
- Is there an easy way to know the memory stats of
the cluster? The memory command on the cluster
doesn't seem to be giving me the correct stats. Is
there any other utility that I can use?
Yes, you can get this and quite a number of other information via JMX. Please check this wiki page for more information.
I started all the nodes with the same configuration
as below. Can you please answer the above questions
ASAP?
<distributed-scheme>
<scheme-name>TestScheme</scheme-name>
<service-name>DistributedCache</service-name>
<backing-map-scheme>
<local-scheme>
<high-units>10000</high-units>
<eviction-policy>LRU</eviction-policy>
<expiry-delay>1d</expiry-delay>
<flush-delay>1h</flush-delay>
</local-scheme>
</backing-map-scheme>
</distributed-scheme>
Thanks
RaviBest regards,
Robert

Configuration Question on local-scheme and high-units

I run my Tangosol cluster with 12 nodes on 3 machines(each machine with 4 cache server nodes). I have 2 important configuration questions. Appreciate if you can answer them ASAP.
- My requirement is that I need only 10000 objects to be in cluster so that the resources can be freed upon when other caches are loaded. I configured the <high-units> to be 10000 but I am not sure if this is per node or for the whole cluster. I see that the total number of objects in the cluster goes till 15800 objects even when I configured for the 10K as high-units (there is some free memory on servers in this case). Can you please explain this?
- Is there an easy way to know the memory stats of the cluster? The memory command on the cluster doesn't seem to be giving me the correct stats. Is there any other utility that I can use?
I started all the nodes with the same configuration as below. Can you please answer the above questions ASAP?
<distributed-scheme>
<scheme-name>TestScheme</scheme-name>
<service-name>DistributedCache</service-name>
<backing-map-scheme>
<local-scheme>
<high-units>10000</high-units>
<eviction-policy>LRU</eviction-policy>
<expiry-delay>1d</expiry-delay>
<flush-delay>1h</flush-delay>
</local-scheme>
</backing-map-scheme>
</distributed-scheme>
Thanks
Ravi

I run my Tangosol cluster with 12 nodes on 3
machines(each machine with 4 cache server nodes). I
have 2 important configuration questions. Appreciate
if you can answer them ASAP.
- My requirement is that I need only 10000 objects to
be in cluster so that the resources can be freed upon
when other caches are loaded. I configured the
<high-units> to be 10000 but I am not sure if this is
per node or for the whole cluster. I see that the
total number of objects in the cluster goes till
15800 objects even when I configured for the 10K as
high-units (there is some free memory on servers in
this case). Can you please explain this?
It is per backing map, which is practically per node in case of distributed caches.
- Is there an easy way to know the memory stats of
the cluster? The memory command on the cluster
doesn't seem to be giving me the correct stats. Is
there any other utility that I can use?
Yes, you can get this and quite a number of other information via JMX. Please check this wiki page for more information.
I started all the nodes with the same configuration
as below. Can you please answer the above questions
ASAP?
<distributed-scheme>
<scheme-name>TestScheme</scheme-name>
<service-name>DistributedCache</service-name>
<backing-map-scheme>
<local-scheme>
<high-units>10000</high-units>
<eviction-policy>LRU</eviction-policy>
<expiry-delay>1d</expiry-delay>
<flush-delay>1h</flush-delay>
</local-scheme>
</backing-map-scheme>
</distributed-scheme>
Thanks
RaviBest regards,
Robert

What are the backend configuration required for photo upload from portal?

Hi all,
When i am trying to upload the photo from portal it is giving error
can not archive the photo
we are using portal 7 and ecc 6.0
I want to know
What are the backend configuration required for photo upload from portal
Can any but help me out
Rajendra

Hi,
Are you using the standard iview. If that's the case you need to configure in the backend. Meaning you need to store the photo in the Org management(HR) which the HR functional guys will do. You just need to add the iview to your role.
Let me know if you require further informationn.
Award points if helpful.
Cheers,
sathya

DPS Potential buyer questions

Hi. I have a little experience with InDesign CS6 which I have used to create and publish epub books. I now would like to create single edition apps. I already have an Apple Developer account. After looking at a number of different solutions Adobe DPS single edition looks most suitable but I am confused by the options so I have some questions.
1) Is Indesign and DPS all the software I need to create and output the app or is there something else that must be bought?
2) Does the price of Adobe DPS single edition mean I own it, ie it won't expire after a set period of time?
3) Adobe Creative Cloud gives a 1 year license to adobe software - does this license also include Adobe DPS single edition?
4) I don't need all the Adobe Creative Cloud software, if I just licensed Indesign CC, because it's cheaper, is Adobe DPS single edition still included.
5) Is it likely that support for Android and Amazon single editions will be added in the next year?
6) Can you point me to any resources on the internet that are good for teaching how to use DPS?
Thanks!

1. InDesign is the base, but any HTML knowledge will be a big help as will Edge Animate and Muse (both part of Creative Cloud)
2. It's an app, you create it and submit it to Apple. If approved it will stay on the app store as long as your Apple Developer account is active.
3. Creative Cloud includes an unlimted number of Single Edition apps. The first year is less than the cost of one SE license.
4. No. And you will quickly discover the rest of the CC apps are indeed quite a nice compliment to InDesign.
5. No. (my opinion only)
6. www.google.com and look around here as well.

Closed loop configuration question

I have a motor(with encoder feedback) attached to a linear actuator(with end limit switches).
The motor has a commercially bought servo drive for control.
The servo drive will accept either a step/direction (2 seperate TTL
digital pulse train inputs) or an analog -10 to 10vdc input for
control.
The purpose is to drive a linear actuator(continiously in and out) in
closed loop operation utilizing a ( (SV) Setpoint variable)value from a
file converted to a frequency to compare with an actual ( (PV) Position
variable) measured frequency.
I have created and experimented with individual vi's allows analog
control and digital pulse train control (thankfully with the help of
examples).
Before I pose my question, I would like to make the following
observations: It is my understanding that Closed loop control
means that I dont need to know an exact position at which to drive, but
constant comparision of PV and SV through PID applictation.
Without getting into any proprietery information I can say that the
constant positioning of the linear actuator will produce a latency of 2
to 3 seconds based on the time the actuator moves to a new position and
when the PV will change. While experimenting with the analog
input, i noticed imediate response to motor velocity, but after the
motor is stopped, position is not held in place. However, while
experimenting with the Digital pulse train input, I noticed that the
servo drive can only accept one command at one time; if, halfway
through a move, position error produces a response to move the linear
actuator in the opposite or different direction, the origional move
must finish first.
Can anyone recommend the proper configuration for the closed loop control i have described?
If I can make the system work with the servo drive/motor I plan to use
the simple (pci 6014) daq card with the Analog out, or utilize the
digital out.
If I cant get this to work, we do have a pxi with 7344 motion card(I
would like to exhaust all efforts to use the PCI 6014 card).
Depending on where I go from here, I planned to use the PID vi's for the loop control.
Thanks,
Wayne Hilburn

Thanks for the reply
Jochen. I realize there is a built-in latency with windows but I
think the I/O control would be ok. A change in actuator position
will not result in an immediate change in process variable; Is
there a way to measure the latency or is it calculated? A
satisfactory reaction time could be from 1 to 1.5 sec.
Use of the PCI-6014 is to supply the control output to the servo
drive/amp, and not to drive the motor itself. As stated earlier,
while using the 6014 board, I have the choice of digital or analog
output.
Currently I am at a point where I must choose which configuration,
analog control or digital control(in the form of digital pulse train),
(i am inserting from first message)
While experimenting with the analog
input, i noticed imediate response to motor velocity, but after the
motor is stopped, position is not held in place. However, while
experimenting with the Digital pulse train input, I noticed that the
servo drive can only accept one command at one time; if, halfway
through a move, position error produces a response to move the linear
actuator in the opposite or different direction, the origional move
must finish first. .
I dont claim to understand all the limitations with the
specific boards, however, i am using an approach that is showing me the
characteristics(a couple are listed in the above paragraph) of
the hardware and software configurations.
So I am really back to my origional question; Which configuration
would be better for closed loop control, analog or digital pulse train?
Thanks,
Wayne Hilburn

Multiple Oracle Configuration Question

We have a typical environment setup. I will explain it below:
Our application works in Online and Offline Mode. For Online mode we connect to Oracle 10g enterprise server and a Local instance of Access and In offline application totally works in Access.
Now we want to move away from Access and have Oracle PE instead just because we want to use stored procedure and same set of code for offline and online processing.
So a typical user machine will have a PE instance and a Oracle Client. Currently we use LDAP.ora for Configuring connections. Now i have few questions
1. How do we ensure that Oracle PE will work when we don't have network connection. Can we have like PE setup with Tnsnames.ORA
2. What can be the smallest possible package for PE.
3. Can I use one client to access both PE and Server databases.
Any help will be highly appreciated.
Thanks in advance.

Assuming the "Xcopy installation" refers to using the Windows xcopy command, can you clarify what, exactly, you are installing via xcopy? Are you just using xcopy to copy the ODP.Net bits? Or are you trying to install the Oracle client via that approach?
If you are concerned about support, you would generally want to install everything via the Oracle Universal Installer (barring those very occasional components that don't use the OUI). Oracle generally only supports software installed via the installer because particularly on Windows, there are a number of registry entries that need to get created.
You can certainly do a custom install of the personal edition on the end user machines. There are a few required components that I believe have to be installed (that the installer will take care of). I assume your customization will take the form of a response file to the OUI in order to do a silent install?
Justin

CCMS configuration question - more than one sapccmsr agent on one server

Hello all,
this might be a newbie question, please excuse:
We have several SAP systems installed on AIX in several LPARs. SAP aplication server and SAP database is always located in different LPARs, but one LPAR can share application server of several SAP systems or databases of several SAP systems.
So I want to configure SAPOSCOL and CCMS-Agents (sapccmsr) on our databse LPARS. SAPOSCOL is running - no problem so far. Due to the circumstance that we have DBs for SAP systems with kernel 4.6d, 6.40 (nw2004), 7.00 (nw2004s) I want to use two different CCMS-Agents (Version 6.40 non-unicode to connect to SAP 4.6d and 6.40 + Version 7.00 unicode to connect to SAP 7.00).
AFAIK only one of these can use shared memory segment #99 (default) - the other one has to be configured to use another one (e.g. #98) but I don't know how (could'nt find any hints on OSS + Online Help + CCMs-Agent manual).
Any help would be appreciated
regards
Christian
Edited by: Christian Mika on Mar 6, 2008 11:30 AM

Hello,
has really no one ever had this kind of problem? Do you all use either one (e.g. windows) server for one application (e.g. SAP application or database) or the same server for application and database? Or don't you use virtual hostnames (aliases) for your servers, so that in all mentioned cases one CCMS-Agent on one server would fit your requirements? I could hardly believe that!
kind regards
Christian

Master iPad configurator question concerning cart syncing with different versions of iPads.

I have a question concerning configurator syncing.Can the master iPad be a different version of iPad than the other synced iPads? For instance can iPad 2 be the master iPad to a group of iPad Air's? The iPad 2 has some fewer capabilities than the Air, would some settings or restrictions be left off of the iPad Airs if they were set up this way? Thanks.

There is no such thing as 'master iPad'. If you're using Configurator or Profile Manager control of the setup is done from a Macintosh.

Setup/ Configuration Question

The network setup I'm using is a wireless G router, Belkin brand, and I have four WRE54G expanders throughout the warehouse. I don't have WEP turned on so I used the auto configuration on all of them. They all made connection and they all work. However, each one of them tends to lose connection from time to time. At least once every couple of weeks I have to reset one of them. When they stop working the red light comes on and I know the link is gone. I'll reset it and everything will be fine for a while. I thought I'd try to get into the web utility to check if any settings are off, however because it has been auto configured I'm not sure what the ip address is. It's not the default. We use a 10.x.x.x range and I've scanned the entire range and none of them show up on an IP. The only thing that does, besides the computers connecting, is the router. I've run the linksys setup utility and had it do a site survey but it keeps coming back saying that the site survey failed. I hate to take them all down from where they are mounted and physically connect them to check things, but I'm not sure it that's the problem. Any ideas would be appreciated. Thanks. If the question I am asking here has already been addressed, please point me to the related thread.
(Edited subject to keep page from stretching. Thanks!)
Message Edited by JOHNDOE_06 on 06-21-2007 08:57 AM

Still kinda funny that the site survey fails. Are you using a Vista computer? Saw that using a XP computer solved someone's problem.
If you can't get the setup software to work you really need to find out what IPs were assigned to the REs to access the IE interface or hard wire them (v2 and 3). I know it is alot of work. I guess you have to assess how much of a hassle it is.
I don't know if the RE shows up on ipconfig/all. I guess it should since it has a unique IP address. Mines the default so I'll check and repost.
I'm wondering what the effect is of having 4 REs in relatively "close" proximity is? When mine loses connection (infrequently), the light turns red but immediately turns blue cuz it connects to router again (got only 1 RE). Would your's connect to the router or to another RE? If it connects to another RE, I guess you lose half the speed again. Interesting....
Also, other than the blue lights, do have any other indication that the REs are working, e.g. increased signal?
Message Edited by Luckydog on 06-21-2007 11:53 AM
Message Edited by Luckydog on 06-21-2007 12:02 PM
Message Edited by Luckydog on 06-21-2007 12:13 PM

Oracle hardware and storage solution configuration questions

Hi all,
I am configuring hardware and the storage solution for a project and am hoping to have some questions answered about using Oracle as the storage solution.
The current setup will have 2 Dell NX3100 NAS gateways each with dual quad core processors, 24GB of RAM, 12x2TB data disks, and running Windows Storage Server 2008 64bit as the OS.
Will also have direct attached storage of 2 Dell PowerVault MD1200 disk arrays, each disk array with 12 x 2Terabyte SAS disk drives giving a total of 36TB of storage space for each NAS Gateway.
Based on this information, is there any problem with two Oracle Standard Edition installation (1 per NAS) holding up to 36TB of data (mostly high res images) in this hardware configuration?
Does Oracle have a built in solution for replicating data between the 2 NAS heads and down to the disk arrays? Where the application sever will write to one of the NAS+disk arrays and then that data is written from the first NAS to the 2nd NAS+disk array? Currently I've used DoubleTake in other projects but am wondering if Oracle has something similar that is built in.
Finally, will Backup Exec Oracle agent work with this configuration for backing up the data to a Dell PowerVault ML6020 Tape backup device?
Thanks in advance for any insight.

Hi,
Does Oracle have a built in solution for replicating data between the 2 NAS heads and down to the disk arrays? Where the application sever will write to one of the NAS+disk arrays and then that data is written from the first NAS to the 2nd NAS+disk array? Currently I've used DoubleTake in other projects but am wondering if Oracle has something similar that is built in.NAS - I still doubt during the network issues (In case of RAC - all nodes would get afftected), I would not suggest certainly for this. Let the other experts reply back.
- Pavan Kumar N

SQL Server 2012 Failover Cluster configuration questions

Hi,
I have few questions on , SQL Server 2012 Failover cluserting pleasse provide suggestions:
1) In SQL Server 2012 is there a configuration for active / passive Failover Cluster installation? If so how is it done? if you could provide any links or articles that would help.
OR
Is this been replaced by Always ON Availability Groups?
2) Also in our environment we have done active/active installation but at a time my understanding is only node has the ownership to the shared storage versus both the nodes, is that correct? If not please provide an explanation?
Any additional information would be valuable in clearing my doubts?
Thank youy
Malini=

Hi malinisethi,
If you install SQL Server in a cluster and configure Active-Passive cluster. In the first node, select “New SQL Server Failover Cluster installation” option , when we are installing Active-Passive cluster, we have to specify one virtual/network name. (Note:
For Active-Active clustering you have specify different network names as per the number of nodes). on the other nodes is similar to installing on the first node except that we have select the Add Node to a SQL Server failover cluster option from the initial
menu. For more information, there is a similar issue about SQL Server 2008 Active-Passive/Active-Active cluster installation, you can review the following article.
http://sqldbpool.com/2009/10/07/sql-server-2008-active-passive-cluster-installation/
About Active/Active SQL Cluster, two clustered SQL Server instance are created in different nodes. Then apply Active /Active configuration of both instance. There is an example about creating an Active/Active SQL Cluster using Hyper-V. you can review the
following article.
http://blogs.msdn.com/b/momalek/archive/2012/04/11/creating-an-active-active-sql-cluster-using-hyper-v-part2-the-clustered-instances.aspx
Regards,
Sofiya Li
Sofiya Li
TechNet Community Support

DPS backend configuration question

Similar Messages

Maybe you are looking for