DR Server Setup using GLVM/DB2 HADR and HACMP/XD.

We have CI/DB of SAP ERP SR3 and SAP BI 7.0  SR3 based on AIX 6.1 / DB2 9.5 installed on two separate LPAR's ( one LPAR has ABAPJAVA ERP CI/DB and otherABAPJAVA BI CI/DB) in P570 system at main site.
DR site is 20Kms away from main site IBM has proposed to setup Async GLVM for SAP instance & Async DB2 HADR for DB2 HACM/XD based cluster for above mentioned ERP and BI systems on two separate LPAR in P550 system at DR site.
We have Monthly DB growth of approximately 8GB on ERP server and 12 GB on BI server.
DR site is 20 Kilometers away from Main site and connected to main site via 8Mbps dedicated leased line.
I would like to know if this proposal is workable with above mentioned DB growth over the limited bandwidth we have and with possibility of data loss using async setup.
I would also appreciate if anyone forward me SAP best practice or recommend best way going forward for our environment, we intend to failover SAP and DB2 instance to DR site system which is 20 Kilometers apart from main site.
Best Regards
Mohammed Ashraf
Edited by: Mohammed Ashraf on Mar 15, 2010 10:21 AM
Edited by: Mohammed Ashraf on Mar 15, 2010 11:08 AM

Since GLVM and HADR are both replicating data (LOGBUF in case of DB2) over the TCP/IP network, you need to compare the daily (or hourly or even more granular) data volume averages and peaks with the bandwidth of the pipe (which is 8MBps in your case). Theoretically, growth of 12 GB per month is not very high and should not really stress the bandwidth of your TCPIP connection but your network administrators will be able to give you a more detailed answer once you provide them with the amount of volume you expect to see flowing between the primary and the DR site. Since your replication is async, you should not really experience any issues due to workload peaks (provided there is enough bandwidth). We replicate one of our bolt-on (non-SAP) systems using HADR and "rsync" for the application files without any issues. The log volume and growth of this system is about 200 GB per month with about 2 GB of data moving across the wire every hour without any latency or performance problems.
Hope this helps!
- Sameer

Similar Messages

  • Problem-Starting InDesign Server for use with CORBA / Java and IOR file not generated

    I'm trying to start Indesign Server cs3 for use with Corba, as per the document the server should generate the start-up message like this..
    InDesignServer -iorfile c:\ior.txt -pluginpath Server\Corba
    [server] Writing IOR to ... and it should generate the IOR file
    but I'm getting the usual start-up message and the IOR file is not generated, I hope IOR file is required for Java component interaction with IDS, kindly help me to solve this.
    Thanks in advance.

    [From Susan Doan, who is having trouble posting to the forum today}:
    It looks like the example command line in the "Intro to InDesign Server" pdf is using curly quotes instead of straight quotes. If you copy the command from the pdf and paste it in your command shell, it won't work because of the curly quotes.
    You can run the command without the quotes as Rich has said, but, as will all command lines, if your path contains a space, you will need to put quotes (straight ones!) around the path.
    Thanks,
    Ole

  • Can the Adobe Update Server be used to automatically download and install updates?

    Can the Adobe Update Server be used to download and install updates to Creative Cloud apps automatically without admin or user intervention?
    I've noticed there is a Adobe Remote Update Manager, but I would rather all the updates and installs happen in the background.

    Hi Nicholas,
    Please check the link given:- https://helpx.adobe.com/creative-cloud/packager/using-remote-update-manager.html
    Let me know in case you require more detail on the topic.
    Sarika Behal

  • Lion Server Setup (Network Login/Mobile Account and more...)

    Hardware:
         Mac mini Intel Core i7, 2 GHz, 8 GB memory (Server)     x 1
         iMac 21.5" 2.8GHz Intel Core i7, 12 GB memory (Workstation)     x 6
    Operating System:
        Mac OS X Server Lion 10.7.4 (11E53)
         Mac OS X Lion 10.7.4 (11E53)
    Relevant Software:
         Server.app Version 10.7.4 (1.4.3)
         Workgroup Manager Version 10.7 (400.3)
         Server Admin Version 10.7 (355)
    So my head's swimming with "I dunno's" and I've been perusing probably all the wrong threads trying not to sound like a noob and find the literature that will finally lead me to a solution.  This is my first rodeo so make no assumptions about my experience (maybe).
    Short Version
    I can't login network users.  I get an error "You are unable to log in to the user account "<%short_name%>" at this time.  Logging in using >console tells me this No home directory: <path to home directory>    i.e. /Network/Servers/department.domain.com/Department/Accounts/bbunny
    If anyone can point me where to read, I will do so.
    Perhaps a longer discussion on how to verify that the proper permissions exist on the share/home directory in question and what those would be.
    More detail...
    I want to setup a Mac Mini server to have network login accounts stored on the 2nd data volume in a directory we shall call Accounts*.  Here all the "network users/logins" have their home directories, so that when they login at the workstation the idea is the workstation will sync their account and allow them to login, if the server is not available, the hope is I can configure it to allow them to login if they've logged in before and the files will sync when they are able. That being the ideal, I get the impression that for best practices, Apple is discouraging the use of mobile accounts that use Home Sync perhaps because it's reliability has been iffy, please advise.  A windows user might think of this as "roaming profiles" but, if I understand it, its a little more than that.
    Note, I do not want to login to the server and actively work on that network share, I want the account to be local and sync'd as needed.  But I want the user to be able to sit at any of the 6 other workstations and see the same documents, emails etc.  Obviously if the server is down, it won't be possible to authenticate, but I think it should have cached credentials that should allow the user to login if the server is down and still go about their work.
    This is the small picture...there is a larger picture that involves, parallel virtual machines of Windows Server 2008 R2 on server and and Windows 7 on the client, ical, ichat and perhaps wiki's.
    I apologize for the roughness of this question, in the interest of brevity, I have plenty of problems that led me here that I can expound upon if asked.
    Also a silly question someone might know the answer too, Why does the login payload settings that I have pushed to a workstation device, sometimes vanish inconsistently upon logout? 

    Ok, Some Good news and clearer understanding to disseminate in this post I hope it helps
    "the Universe" so I am posting it here in my "ever-the-noob" blog on apple forums.
    Problem
    What do you do when you get an error when logging into a mobile account setup?
    One symptom would be the error message below...
         "You are unable to log in to the user account "<%short_name%>" at this time.
    Logging in using >console  You get the message…
         "No home directory: <path to home directory>"
         or
         "You are unable to log in to the user account "<%short_name%>" at this time. 
         Logging in using >console tells me this No home directory: <path to home directory>
    Solution
    Do the check list…
    Short Version
    Sever Admin.app > Access (Key Component)
    Check Permissions on directories for your file shares. 
    (The reason stuff doesn't work especially when you're rebuilding/recovering a server)
    File sharing setup (Turned ON, Home sharing Enabled)
    Directory Utility > Directory Editor or dscl 
    ( Do not underestimate the importance of this part!!!!
    Use white-gloves when you're handling it though!!! )
    Workgroup Manager
    (You're poopy "main" interface that really is a "window", not a "door", but maybe Apple likes to do things "Dukes of Hazard" style?)
    Long Version
    Check Sever Admin.app > Access
    Make sure that your user has the "Proper" access.  For me I created a test user from Server.app and saw what access he had as a way to "check myself for a properly created users" and because I think one is kind of on his/her own using WGM and duplicated the same access. (I was a little neater, though and did it with a group, not individual users, that would have been a mess!)
    Server Admin.app > Access
    Click the "+" sign, sort by UID and Add the imported users  to the following Services…
    ( You can use a group, but understand when Server.app creates users they get added
    individually to each of these groups. )
    Address Book
    AFP
    iCal
    iChat
    Mail
    Profile Manager
    SMB
    VPN
    Check Permissions on directories for your file shares. 
              (That's an understatement) I could go in depth about all the crap I had to read about, I still
              know I am missing a chunk of tech brain when it comes to the particulars. Basically, I boil
              it down to this…
              Permissions require thinking about things first with regards to POSIX permissions... good
              ole ls, chmod, chgrp, chown to the rescue with ugo permissions or the old 755, 600 etc
              stuff.
              Apple's file-sharing access uses this as a starting point to see what the user is allowed to
              access.
              I also needed to use chflags once to unhide a file that I mucked around with using xattr. 
              I still haven't figured out why folders can lose their triangles, but I didn't find out if you cp or
              move them from terminal, the triangles come back in the moved or copied directory.  For a
              minute I thought it was because cp alone doesn't preserve flag attributes, but mv actually
              works by doing a cp that preserves the flags, unless it's a bug.  I dunno.
              This helped me get my file visible again...
              chflags hidden path_to_file
              chflags nohidden path_to_file
              Read up on those manuals, if you're not a terminal type go to apples website
              http://developer.apple.com/library/mac/#documentation/Darwin/Reference/ManPages/
              or download...
              http://www.bruji.com/bwana/ I thought that was cool.
              or if you prefer to read the manual in pdf try…
      man -t sharing | pstopdf -i -o ./Desktop/Sharing\ Manual.pdf
              man -t chown | pstopdf -i -o ./Desktop/CHOWN\ Manual.pdf
              man -t chmod | pstopdf -i -o ./Desktop/CHMOD\ Manual.pdf
              man -t chgrp | pstopdf -i -o ./Desktop/CHGRP\ Manual.pdf
              My basic guideline was avoid using ACLs if at all possible, if you try to use them, things
              can get crazy complicated, take notes and plan, baby. If you read above, opening up
              permissions wide is wrong though.  You would restrict permissions tightly to begin with and
              then place ACE (Access Control Entries) to specifically target the rights you want to enable.
              Here's one that's obviously a novice attempt to do this, but since the novice is the only one
              speaking…. here it is, Universe… >:P
              sudo chmod -R +ai "admin allow read,write,delete,file_inherit,directory_inherit,search,list" Department/
              That allowed my admin to do all the things a normal user could do so far… It fixed things for
              my admin, which made me happy.  I really hate having to authenticate or sudo just to see
              the contents of a nested directory.  I could explain it, and even give a few notes on why its
              probably overkill, but I will attempt to look less stupid till "poked".
              There's another command line utility I STILL haven't read, which may bear mentioning
              because…well I haven't read it.  umask (see wikipedia or unix.com)…I worked past my
              problems without going into it so far, but obviously it's there, and it serves a purpose.
              I also found this article helpful…and educational.  :O
              http://www.bresink.de/osx/300321023/Docs-en/pgs/ACL.html
              (          Its enlightening to hear the air whistling between a developer/coder's ears, still it's
                        apparent he has a clear idea what's going on.
                        Ever wonder why when you use get info to check or assign permissions it kind of
                        flakes out and doesn't take?  Read this article!          )
              Second, if you can't obtain the "specific" permissions you need with POSIX, chmod also
              can set the 2nd category of permissions, which windows users may be familiar with
              Access Control Lists (ACLs) and here you get some really fine granularity...messy stuff. 
              All in all, if I felt I could guide you through these murky waters, I would, but I think I'll let
              the professionals weigh in on that one and cut my wall-of-text to ribbons.
              To heuristically check I would connect from a client as one or two of my users and see what
              folders I could mount as a share, armored with an understanding of what ls -le@O * showed
              me in Terminal.
    3.)           File sharing setup (Turned ON, Home sharing Enabled)
              Here is an example of using command line sharing utility where each share is properly
              labeled (that took a bit for me to figure out) still this share only enables the AFP share as
              you can see from my flags.
      sudo sharing -a /Volumes/Hard\ Drive/Department/Database -A Database-afp -F Database-ftp -S Database-smb -n Database -s 100 -g 000 -i 10
              Then you do a sudo sharing -l and get back what you just did…
                                              List of Share Points
              name:                    Database
              path:                    /Volumes/Hard Drive/Department/Database
                        afp:          {
                        name:          Database-afp
                        shared:          1
                        guest access:          0
                        inherit perms:          1
                        ftp:          {
                        name:          Database-ftp
                        shared:          0
                        guest access:          0
                        smb:          {
                        name:          Database-smb
                        shared:          0
                        guest access:          0
              If you mess up the sharing command, you may not be paying attention (I wasn't) but there
              are a lot of defaults that Apple will just assume you meant to do anyway and it won't read
              any of your flags, you have to get it right or the flags will be defaulted. 
              (          Basically I could tell I was bombing it for one, I explicitly only wanted afp working, but
                        the default was afp and smb.  So each time I ran sudo sharing -l after I shot my sharing
                        command…back would come smb shared: 1 and I knew that wasn't right.  Also my
                        custom names were defaulting to the name of the directory not the name I had
                        specified.           )
              I like to know what protocol my share is over so when it doesn't work, I know which protocol's
              are connecting. It's not full-proof, but it's a bookmark.  I wish the network browser would
              identify the protocol that its available listed shares are using, because small visual queues
              like that help when you're trying to see what works.  Maybe that's something I should
              investigate via the command line?
              As a note about reading forums, I discovered using command line that "\" is kind of like a
              way of going to next line neatly with long commands…."\ " is a way to insert a space. As you
              can see above where I have a volume with a space in it. 
              Removing shares was a little trickier though, sharing -r Share\ With-space didn't work….I
              had to enclose it in quotes and do "Share With-space" instead. So nooby beware!
              (          *nix users are now rolling their eyes at this tip.          )
              I wasn't sure how you enabled a share for home directories from the command line, maybe its
              in the manual, but I was up to my eyeballs in manuals already so I haven't gone back to
              revisit this question since my work around was to go to Server.app and verify that what I set
              up in the sharing in terminal was being reflected in the gui…sort of my own MVC
              (model-view-controller) check.
    4.)           Directory Utility > Directory Editor or dscl 
      Make sure what you see in WGM and Server.app are reflected here….to that question let's
              take a journey where I did some exploring about that.
      Ever really wonder "WHY CAN"T I REMOVE AN OLD HOME DIRECTORY SHARE?!!!"
              Ah, then you will  - LOVE -  this tip…
              (          Provided my testing or yours, later, doesn't prove that in my ignorance I've broken
                        Open Directory. Remember, WHITEGLOVES!!!! but here we get a little dirty.  I think of
                        OD as Apple's Registry, but that's not what it is at all. However, you as the user do have
                        to "****" around in it from time to time.          )
              I scoured the forums and everyone was saying things like "You have to change your server
              role" etc. which seemed a little bit dumb to me (dumb because you're pushing views around
              not "controlling"), and well, yea, that share that I couldn't modify or delete was REALLY
              bugging me.
              Now hmm… Before you do ANYTHING, how do you try to not hurt yourself…in Windows you
              can make a Registry Backup….(yea bad analogy)  In Server Admin.app you can go to your Open
              Directory Service > Archive and Choose a place to Archive your information. (Figure this out by
              yourself, this is getting long…sheesh! It's easy. Restoring is just as easy and painless.)
      Before we can remove the entry we "SEE" in WGM we should make sure no
              one has it selected so as not to "corrupt" the OD db, so in WGM first before going to Directory
              Utility set the Home directory to "None".  (We need to remember to set this to a correct share
              later….Mental Note!!!)
              Now Open Directory Utility
              Method 1
              System Preferences > Users & Groups > Login Options
              Click the Lock to make changes…
              Authenticate -> click "OK"          (do I REALLY have to step-by-step this?)
              Network Account Sever: • Local Server - click "Edit" button here.
              Open Directory Utility > Directory Editor
              (          Wow, did Apple hire someone from Microsoft?  You'ld think with all their research in to
                        Human Interface Design that's WAY too many clicks to get to something you need.          )
              or
              Method 2 (It's good to know about this directory, neat-o speed-o app's hidden here.)
              Use "Go to Folder" Under Finder > Go > Go to Folder...
      ⇧⌘G /System/Library/CoreServices/ 
              Click "OK"
              and Double click Directory Utility.app
              or
              Method 3
              Terminal
              open /System/Library/CoreServices/Directory\ Utility.app/
              Now From the Directory Editor Pane you will see a Pop-up menu Labeled "Viewing"
              You should glance through this and get to know it.  You should use it to see what
              information is really being stored about your Users, Groups, Mounts…
              We are interested in Mounts, which is where we want to go…and there is the pesky
              mount that you will see reflected in WGM.
              Authenticate, and delete the bugger.
              Quit WGM and restart it.  Voila, bad share is GONE!!!!!
              a.)          First select all my users
              b.)           Then I clicked on the "+" and added the correct share
                        (          Remember, I only showed you the first one we created, this is another and
                                  for THIS one you HAVE to go into Server.app and verify that it is set to be
                                  available for Home Directories in this case for AFP.          )
                        For the home directory entry you do this...
                        afp://computer.domain.com/Accounts-afp
                        %short_name%
                        /Network/Servers/computer.domain.com/Volumes/Hard\ Drive/Department/Accounts/%short_name%
      %short_name% is a wild card for the short name there are other wild cards check out Apple's
                        Documentation on them.  I lost the link   sorry \<shrug\>
              Interesting dscl commands…(check it out in command line form and compare side by side with
              what you see in the GUI Directory Utility)
              dscl . list /users
              dscl . list /groups
              If you want to output information about each user, though, use readall:
              dscl . readall /users
              dscl . readall /groups
              And if you need to programatically parse said information, use -plist to make your life easier:
              dscl -plist . readall /users
              dscl -plist . readall /groups
              This made a little more direct sense to me, language wise…but fyi "." is kind of a wild card I think so the first
              commands I think look in ALL directories local, Search, LDAP whatever you have.  The command here
              corresponds to the Entry from the Pop-up menu "…in node > Blah…" see GUI of Directory Utility to confirm.
              dscl /LDAPv3/127.0.0.1 -list /Users
              dscl /Local/Default -list /Users
    5.)          Workgroup Manager
              Remember this is a utility that is not long for this world.  Apple's Mountain Lion is rumored to fully
              replace it, why? Yea, Apple's making a go at MDM (Mobile Device Management) and somehow
              desktop computers are being pulled/dragged along for the ride.  I have plenty of issues with
              Profile Manager, but I'll likely revisit it in a couple of months and see where we stand.
              Anyway, treat this baby like the bottom rung, because, well it is built like you start your
              foundation here, but it's just a viewer with controlling "tweaks".  Use the other areas to get a solid
              grasp of what is actually going on.  Server.app is where you should create accounts you can
              feel are safe.  When you create accounts in WGM, you are responsible for making sure they
              have the appropriate EVERYTHING.
    This list is by no means complete, but these are the areas this noob is or was prepared to talk about.
    Good night for now.  Enjoy climbing my wall of text, and yea sorry about that.  :O Run for you lives!!!!
      - Signed Shadowwraith

  • Cannot connect to Exchange server (Small Business Server 2008) using Windows 8.1 and Outlook 2013

    I am at my wits end. I have got a new PC running Windows 8.1 and Outlook 2013 simply WILL NOT connect to my work Exchange server. The REALLY annoying thing is that the Windows Mail client inbuilt to Windows 8.1 works perfectly! But I have to have Outlook
    for the functionality. The issue appears to be that in Outlook 2013 on Windows 8.1, it tries to be clever and auto-detect the settings whereas Windows Mail allows you to input the server and domain names.  
    I have tried all the suggestions already on some of the boards - manual setup, etc - nothing works! Is it a compatibilityissue with SBS 2008 and Outlook 2013? Any help appreciated!

    I am at my wits end. I have got a new PC running Windows 8.1 and Outlook 2013 simply WILL NOT connect to my work Exchange server.................... it tries to be clever and auto-detect the settings.  
    I have tried all the suggestions already on some of the boards - manual setup, etc - nothing works! Is it a compatibilityissue with SBS 2008 and Outlook 2013? Any help appreciated!
    There's no issue with O'2013 connecting with Ex '2007. Also not clear about comments of "auto-detect" versus "....have tried all the suggestions ............ manual setup....". On the one hand your stating that only "auto-detect" is available and on the
    other that you've tried "manual settings" (which definitely is an option in O'2013 for EX accounts).
    This may have more to do with the fact that you're using a new computer trying to connect to the server which it may not be configured for - something your admin will need to address.
    Given that your question is in reference to Exchange - you are likely to get a better/faster answer in the following forum which deals with Exchange server related questions:
    Exchange Previous Versions - Outlook, OWA, POP, and IMAP Clients
    http://social.technet.microsoft.com/Forums/en-US/exchangesvrclientslegacy/threads
    Karl Timmermans [Outlook MVP] "Outlook Contact Import/Export/Data Mgmt" http://www.contactgenie.com

  • DLU or DSfW for single server setup using NOWS for Small Bus

    I'm planning to install a single server in a 5 user office, plus a few remote users.
    OES 11 SP1, ZCM 11, GW
    As part of this I want to have single sign on to Windows workstations (Win 7), and could use DLU, but I also wonder about DSfW.
    They both would achieve single sign on but in vastly different ways.
    Which way to go? DLU or DSfW?

    Originally Posted by drops
    5 users? in my opinion everything is overkill then.
    The 5 users is expected to grow to 10 within 3-4 months.
    Overkill or not, no end user likes to have two different passwords when they logon, and most don't comprehend the difference between a local logon and the network (OES) logon. If there is a password change policy in place then the problem is compounded.
    So the goal is single sign on with unique profiles.
    Originally Posted by drops
    if its only about desktop access with a local user you have several options
    1. DLU
    A good candidate, though I haven't used it for some time. Satisfies all criteria.
    Originally Posted by drops
    2. pgina LDAP auth - local gateway and novell client passthrough auth
    Never used this...Is it easy to setup and reliable?
    Originally Posted by drops
    3. use a generic windows user
    I've used this on a small Samba setup once, and it is workable, except for no unique user profile, and not ideal from a security perspective.
    Originally Posted by drops
    4. DSfw or AD (synchronized passwords)
    I've never used DSfW hence my post here. My gut feeling is that it is more complex and difficult to troubleshoot than DLU so I'm leaning towards DLU. That said, I'm also interested on your comments of any PGINA implementations you've done, and if it should be considered.

  • Unable to save/publish Projects on Project Server 2010() using Project Pro 2007 and 2010

    Hi,
    Recently we have upgraded from Project Server 2007 to 2010 SP-2 (BCM enabled) environment and from last few days we are getting issue with Project Plans where PMs are not able to update Projects means save and publish the Project using MS Project  2010/2007.
    Whenever PMs try to open project using MS Project 2010 SP-2, it gets load successfully but when they hit save and publish no jobs are getting fired up nothing is happening. Only way to get out from MS Project 2010 window is to close the Project window and
    and click discard changes. No error and exception windows are popping out in MS Project 2010, no error/problem/issue clue at all from MS Project 2010.
    But when I try to update this Project plan for very first time using MS Project 2007 Sp-2 then I am getting below error
    for any subsequent save and publish using MS Project 2007-SP2 getting below error
    As an alternative I have tried to open this Project Plan using web and there it is getting opened saved and published successfully from PWA absolutely no issue.
    Also I have saved this Project locally as XML and saved and published it on Server successfully. But after someday again this project got corrupt PMs started getting same problem again
    I have also looked at ULS logs but not getting anything useful there.
    So any guesses why this could happen that can give me pointers to find actual root cause, please let me know.
    Thanks much !!!
    Sachin Vashishth MCTS

    Used below steps to fix the Projects on MSP 2010.
    1) Open corrupted project in MS Project connected to PS 2010 Prod env.
    2) Goto > Resource > Add Resource  > Build Team From Enterprise
    3) Check is there any local resource who has not replaced with corresponding enterprise resource. If yes then replace all those local resources with enterprise resource. If not then move to next step.
    4) Open resource sheet view and sort or filter by local resources.
    5) Then add few columns in resource sheet view like "Windows User Account, Email Address , Base Calendar etc".
    6) Now check has any local resource having enterprise attribute assigned to it, if yes then delete or assign local value as appropriate.
    7) Then GoTo > File > Save & Send > Save as project file > Save for sharing (at local location)
    8) Close project plan window and click "Yes" to save changes.
    9) Restart MS Project 2010 and open your project from local location.
    10) Then Goto > File > Save & Send > "Publish to Project Server". This will open "Import Project Wizard" to validate Resources and Task in Project.
    11) Then in Import Project Wizard window at left hand side click "Map Resource" to validate project resources.
    12) This will "Map Project Resource to Enterprise Resource " check all the resources highlighted with "Red" font and map "Standard" calendar to local resources.
           Note: Don't worry about local resource assigned "Standard calendar" but still highlighted "Red".
    13) Then click "OK" and click on "Continue to step 2" at bottom of "Import Project Wizard".
    14) Make sure you get number of errors 0 in step 2, else click on validate resource and take proper corrective action as explained in step 6.
    15) If you leave at least one resource as a local resource (unmapped to an enterprise resource), you will see the local resource in the Import Resource grid on the right side
    of the Confirm Resources page.         
    Examine the value in the "Import" column (if not able to see this column then insert this as new column) for the local resource . 
    The default value is "Yes", then change the value in the "Import" column
    to "No", else system will import the local resource as an enterprise
    resource.
    16) Then "Continue to step 3, 4 and 5".
    17) Then at Step 5 , Save project to Project Server by clicking "Save as" link.
    18) Then publish the project to update the plan at PWA 2010.
    Sachin Vashishth MCTS

  • Can the same IIS web server be used for Web Enrollment and AIA and CDP?

    I'm designing a PKI for my company and will need a web server accessible from outside for doing web enrollment as well as for publishing CRLs and AIAs. Can this be the same server?
    Can anyone point me to a good article on how to set this up?
    Thank you.
    Kenny

    yes, you can use the same web server to host CRT and CRL files. And there is nothing complex to create the site. Just create a web site and point it to a folder that contains your files, or add a virtual folder to existing web site.
    My weblog: http://en-us.sysadmins.lv
    PowerShell PKI Module: http://pspki.codeplex.com
    Check out new:
    PowerShell FCIV tool.

  • '[FAQ] Twonky DLNA Media Server Setup & Use

    Some Frequently Asked Questions Regarding Twonky, And Some Answers The MyCloud includes a Twonky DLNA Media Server.  Sadly it doesn't seem very well integrated into the MyCloud, and the two fight for supremacy.  I've spent a long time trying to understand how it works, and reading the forum, I see many other people also have trouble with it. So I thought that, rather than trying to answer these questions individually, I'd try to write an FAQ covering the things I've found, and the problems I or others have encountered, and the solutions.
    I'm not a member of WD staff.  I'm not a MyCloud, Twonky or Linux expert (but I'm moderately competent).  But I am stubborn, and determined to find out how to make the thing work the way I want it to.  If more expert users find fault in this FAQ, or have other insights to offer, then feel free to post comments.  I'll edit this first post and make corrections and add any FAQ&A that are added.
    Where I am unsure of something, I'll enclose it in [brackets].  Feel free to investigate and confirm or disprove my observations... Where I mention control settings, I use a | to indicate a level of hierarchy in the menu system.  This is to distinguish control settings and file system paths.
    Ideally, we'd shame WD into doing a better job of integrating Twonky into the MyCloud, so it's not such a struggle, and doesn't require Linux administrator-level skills to make it work properly. Starting the Media Server and setting up a Media LibraryQ. What is a Media Server?
    Q. How do I start the Twonky Server?
    Q. How do I control the Twonky server properly?
    Q. Where should I put my media so Twonky finds it?
    Q. Why doesn't Twonky find my media?
    Q. Can I stop Twonky searching in certain folders in my media storage folders?
    Q. What are the 'Shared Media' folders for?
    Q. Why can people using DLNA clients see media in my private share?
    Q. How do I control when Twonky rescans the media store? Optimising operation of the Media Server
    Q: How does the Twonky service work on the MyCloud?
    Q. Where is the Twonky database stored?
    Q. Where are the Twonky settings stored?
    Q. What do all the settings in Twonky's configuration file do?
    Q. How do I clear Twonky's database and start again?
    Q. Where can I find debug log files for Twonky?
    Q. How do I stop MyCloud breaking the Twonky Server?
    Q. Can I change to location of the 'Shared Media' folders?
    Q. Why does setting a Twonky access control password prevent the MyCloud from sleeping?
    Q. Can I replace Twonky with another Media Server?
    Optimising behaviour for Media Clients
    Q. Why does my media player not show the right track information?
    Q. How can I get Twonky to provide full size artwork to clients, rather than crude thumbnails?
    Q. How can I change the media 'views' I see in my DLNA client?
    Q. Can I add my own category to the Music/Photos/Videos categories?
    Some Prerequisites
    You'll need to know how to use the WD Dashboard browser interface to control the MyCloud:
    http://wdc.custhelp.com/app/answers/detail/a_id/10420
    You'll need to know how to use the Twonky UI browser interface to control Twonky:
    http://wdc.custhelp.com/app/answers/detail/a_id/3299
    You'll need to know how to use SSH to log in as root to the MyCloud:
    http://wdc.custhelp.com/app/answers/detail/a_id/10435
    Note the big warning signs about warranty.  IMHO, it's a bit off to make dire threats like this when you often NEED to SSH login to get the advertised services to work properly.
    Some Unix experience will help, but I'll try to explain all the commands you'll need.  Experience with a Unix text editor such as vi or nano is assumed.

    Q. How does the Twonky service work on the MyCloud?
    A: [Twonky is installed as a Linux service.  Like other such services, there is a service control file in the /etc/init.d directory]:
    /etc/init.d/twonky
    This is called when the twonky service is invoked, and there are a number of options for the control of Twonky using an SSH root login:
    service twonky start
    service twonky stop
    service twonky restart
    service twonky status If you execute the start or stop commands with Media Streaming turned on in the Dashboard, you are likely to confuse the Dashboard; you may get an 'Error 400162'.
    'start' calls writeTwonkyContentDir.sh, which, as we'll see later (Q: How do I stop MyCloud breaking the Twonky Server?), reads the /etc/contentdir file and modifies the twonkyserver.ini file to set the media search paths and types, and then starts the Twonky server.
    [It is assumed that the MyCloud Dashboard uses these Twonky service calls to start and stop the Twonky server].  Q. Where is the Twonky database stored?
    A: Since Twonky is a service running on MyCloud, it is not visible in the shared space, so you have to log in via SSH, and navigate around the MyCloud's Linux file system.
    Once you have logged in, use the cd command to change directory to Twonky's area:
    cd /CacheVolume/twonkymedia Now see what's there with a directory list:
    ls -l  Q. Where are the Twonky settings stored?
    A: One of the files listed above is the Twonky configuration file:
    twonkyserver.ini This file contains all the settings that control how Twonky works.
    Now, this is where some of the fighting occurs, because both MyCloud and Twonky can modify this file...
    When you are happy that Twonky is working correctly, I'd recommend making a copy of the file in your Public area, where it won't be mangled by MyCloud firmware upgrades or restarts.  For instance:
    cp /CacheVolume/twonkymedia/twonkyserver.ini /shares/Public/twonkyserver.ini
    If things go wrong, you can reinstate this file by swapping the source and destination.  Q. What do all the settings in Twonky's configuration file do?A: [Most of them are provided with comments that explain their purpose].
    [There are some 'magic numbers' embedded in the configuration file that seem to cause problems, and I don't know what changes those; I suspect that a firmware upgrade does it.  If anyone can monitor these values before and after a MyCloud firmware upgrade and report any changes, I'd be obliged:
    # UserID Please Do NOT change it manually
    userid=<redacted>
    # twonky info for Media Feeds Please Do NOT change it manually
    twonkyinfo=<redacted>]  Q. How do I clear Twonky's database and start again?
    A: If Twonky doesn't seem to be behaving correctly (not finding media correctly, or partially, or finding unwanted media), then it may be useful to clean up the database. There are a number of escalating actions you can take.  Starting with the mildest, and increasing in severity, these are as follows:
    1. Initiate a library rescan, using either Settings|Media|DLNA Database|Rescan in the Dashboard, or Settings|Advanced|Server Maintenance|Rescan Content Folders in the Twonky UI.
    2, Initiate a library rebuild, using either Settings|Media|DLNA Database|Rebuild in the Dashboard, or Settings|Advanced|Server Maintenance|Restart Server in the Twonky UI.
    3. Finally, you can completely clear out Twonky's working area. [This can be useful if you notice the '[Error] - LOG_SYSTEM: Error: 2 No such file or directory' report in the Twonky logfile.  I don't know what causes this error, or whether it has serious consquences, but I have found it to be associated with periods of diffcult behaviour.] Turn Twonky off using the Settings|Media|DLNA Media Server|Media Streaming control in the Dashboard.  Then SSH root login, and hide the entire Twonky working area:cd /CacheVolumemv twonkymedia twonkymedia_bak Restart the Twonky Server using the Dashboard; it will re-create Twonky's working area with a clean version with default settings.  You can then use the Twonky UI to put your settings back in place.  You might try doing this one-by-one, saving the settings and restarting the Twonky server from the Twonky UI each time, then checking the logfile after the Twonky UI has re-appeared. Once you're happy with the operation of the clean startup, you can delete the old Twonky working area:
    rm -f -R /CacheVolume/twonkymedia_bak
    The -f -R flags mean 'delete EVERYTHING from here down... yes, I mean it'.  nb. it will only delete the Twonky database; it won't delete any of your media.  But do be careful that you type the command in correctly; rm -f -R is a powerful command (-f means force, -R means recursive), and could do a lot of damage if you get it wrong...
    Q. Where can I find debug log files for Twonky?
    A: You can enable activity logging using the Settings|Advanced|Logging control in the Twonky UI.  You can also open the logfile from there.
    Alternatively, the logfile is stored in Twonky's area:
    /CacheVolume/twonkymedia/twonkymedia-log.txt
    There's also a MyCloud system logfile that records actions on the Twonky server, such as start and stop:
    /CacheVolume/update.log  Q. How do I stop MyCloud breaking the Twonky Server?
    A: Firstly, go to the Settings|Firmware page in the Dashboard, and disable Auto Update: firmware upgrades completely destroy the /CacheVolume/twonkymedia area, and replace it with new, default version, so you'll be back to square one.
    Secondly, we can stop the problem of Media Streaming restarts overwriting the Twonky UI settings.  Using an SSH root login, enter the following commands:
    cd /usr/local/sbin
    mv writeTwonkyContentDir.sh writeTwonkyContentDir.sh.old
    This disables the script that MyCloud calls when it starts Twonky, which overwrites your settings.
    Another way of fixing the settings is to leave this script alone, but change the file it uses as the source of the settings.  Admittedly, this will still override any changes made via the Twonky UI.  The file is found here:
    /etc/contentdir
    Replace this with a single control line, with no line terminator, e.g.
    +M|/Public/Music,+P|/Public/Pictures,+V|/Public/Videos This will select my earlier settings.
    The format is a comma-separated list of shares and media search and aggregation control flags:
    + enable media searching on the share
    - disable media searching on the share
    A look for all media types
    M look for music
    P look for pictures
    V look for videos
    lower case letters enable aggregation of these media types.
    The | terminates the media type string [you can search for multiple types in a share].  Q: How can I change the location of the 'Shared Media' folders?A: This brings us deep into the guts of the twonkyserver.ini file...  There are a number of settings that control where Twonky stores uploaded files and 'servermanaged' media, [which are used for aggregation], and there is no control setting for them in the Twonky UI.  To change the location of the folders we have to do an SSH root login and edit the twonkyserver.ini file.  The lines in question are as follows:
    uploadmusicdir=/shares/Public/Shared Music
    uploadpicturedir=/shares/Public/Shared Pictures
    uploadvideodir=/shares/Public/Shared Videos
    servermanagedmusicdir=/shares/Public/Shared Music
    servermanagedpicturedir=/shares/Public/Shared Pictures
    servermanagedvideodir=/shares/Public/Shared Videos
    You can change these locations to suit your desired file system.  For instance, you could create a single 'Shared' folder in the Public area, with sub folders for the different media types, e.g.
    uploadmusicdir=/shares/Public/Shared/Music
    Or you could create a Shared sub folder within each of your main media folders, e.g.
    uploadmusicdir=/shares/Public/Music/Shared
    However, if you choose that option, you will need to stop Twonky searching there, by adding 'Shared' to the list of ignored directories discussed above.  Q. Why does setting a Twonky access control password prevent the MyCloud from sleeping?
    A: It has been reported that if a username and password are set using the Settings|Advanced|Secured Server Settings control in the Twonky UI, that the MyCloud then never sleeps.  [It appears that the MyCloud continues to interrogate the drive in some way, hoping to get status of the Media Server from Twonky, but Twonky won't talk to it because it doesn't have the required permission.].
    I don't think this is very important, since the MyCloud is mainly intended for home use, and the Twonky control UI isn't visible external to your local network, and all users on your local network must be trusted*, since you've given them the network access code, [and they have access to the Public area, and could wreak havoc there...] If you need to make your music library available to visitors who cannot be trusted, create a private share and put all your media under that, then enable media serving on that share, and get Twonky to search for media in that private share. DLNA ignores acces control, so DLNA clients will be able to see the media on your private share, but visitors will not have access to your private share via network file access. [However, if you feel that secured access to the Twonky UI is necessary, then I would suggest that you disable the Twonky server using the Settings|Media|Media Streaming conrol, then SSH login as root, and start Twonky using the command:service twonky start You won't get the media scan status in the Dashboard, but the Twonky Server and UI will be running.]
    * Breaches of this trust should be punished in an appropriate manner...
    Q. Can I replace Twonky with another Media Server?A: Yes; forum users hvalentim and Nazar78 have posted good threads about this:MiniDLNA for V3 firmwareMiniDLNA for V4 firmware Kudos to them :-) 

  • Pull large amounts of data using odata, client API and so takes a long time in project server 2013

    We are trying to pull large amounts of data in project server 2013 using both client API and odata calls, but it seem to take a long time. How is this done
    In project server 2010 we did this creating SQL views in both the reporting database and for list creating a view in the content database. Our IT dept is saying we can't do this anymore. How does a view in Project database or content database create issues?
    As long as we don't add a field in the table. So how's one to do this with creating a view?

    Hello,
    If you are using Project Server 2013 on premise I would recommend using T-SQL against the dbo. schema in the Project Web Database for your reports, this will be far quicker that the APIs. You can create custom objects in the dbo. schema, see the link below:
    https://msdn.microsoft.com/en-us/library/office/ee767687.aspx#pj15_Architecture_DAL
    It is not supported to query the SharePoint content database directly with T-SQL or add any custom objects to the content database.
    Paul
    Paul Mather | Twitter |
    http://pwmather.wordpress.com | CPS |
    MVP | Downloads

  • 10.5.1 Server Setup - Help Make it all Work!

    Hello Everyone, I currently have a new MacMini running 10.5.1 with our Calendar, Wiki and File Sharing. I have recently just returned from the Mac OS 10.5 Training Session from Chicago Columbia College and was astonished at what their demo servers did versus what mine has never done lol. We are a small tech company and there isn't much yet in the way of documentation or training or even training materials for Leopard Server. So I wanted to share some of what we learned from the training seminar and hopefully someone will know the proper answers to my questions. This is going to be a bit long winded but I think it's important to convey my questions/concerns.
    1. Ok initial setup of our Leopard server requires you to input a host name and then the domain name. Well after the first install of Leopard we found as I have read amongst the posts for the past 2 hours that if you place let's say macmini in the host-name field then place domain.com in the domain field. After the server setup is complete Leopard Server wants you to chat, vpn, and browse to http://macmini.domain.com/groups as well as mail. This is all well and good if you have access to DNS like I do and can easily make changes to the MX & A records but if your a typical SMB user then you won't and this means that once your e-mail is setup and your ready to start using your server anyone you e-mail will come from [email protected] and not [email protected] which is a huge problem. So be cautious here. I was instructed by Apple after scratching their head to leave the host-name blank and only fill in the domain name here if your on let's say a T1 or other medium with a static IP pointed at your machine or router. So this is my first pet peve, there is a sloppy work around to this by telling the server to receive e-mail for domain.com as well but still whenever you send it comes from the original domain.
    2. Application Setup - Single Sign-on - When I attended Leopard training this week in Chicago I was amazed at how whenever a user (demo -lab environment) logged into ichat, ical, wiki or e-mail there was simple single sign-on kerberos auth. What I mean by this is once the server is up and running and your Mac connects to the network for the first time either by manual add thru the directory application or a new Mac that finds the Leopard server automatically at first boot and you auth a user on the server to that Mac then there is just a single signon from that point on, NOT! For us our users log into their machines, (mind u they are already users on the Leopard server and can log in just fine) and they try to go to their e-mail for the first time it always fails. We then have to disable SSL over SMTP and IMAP and manually type in their passwords because the MacMail clients cannot trust the SSL cert or we simply just delete their accounts and recreate them from scratch. Same happens with iChat. By design when you auth your Mac against the server, the server auto configs the security and client apps, i.e. mail, ichat, directory, VPN, ical. But iCal has consistently failed setup across 5 server builds and 10 clients. What will happen is when you go to prefs in ichat you see your account but it can't auth you and doesn't show up in ical for your personal server calendar. If you manually remove your user account and re-add it works great. But next time you go to ichat, once again you have to recreate. And I can recreate this all day long. But at the demo it worked like magic. So that is problem number two, SSL and single sign-on does not really work and app auto-config does not work at all.
    3. Apple Airport Extreme 802.11N. - As a test and per Apple's recommendation for SMB clients we picked up a new Airport. We patched it and setup user/pass info and setup DHCP on the device for so if server fails we have internet. And during server setup it logged into Airport and tried to configure settings. We were on the net and all was good after server setup. However with VPN enabled per user in Standard mode on server we have only been able to gain VPN access for clients if they are actually inside the network. I have spent about 10 hours back and forth with Apple Support trying to get VPN to work outside. The Manual setup of new Airport Port-Mapping is simple but crude. It does not seem to work. And there is a default hosts setting which should translate to an open DMZ but does not. So that is third on my list, running a MacMini with 2gig's of RAM which is within SPEC for Leopard Server and using the Apple Recommended solution of an Airport Extreme N does not work for s&*% and I would be very surprised if anyone here has gotten that to work.
    4. E-Mail Services - As stated prior Leopards auto app setup utility does not work for crap unless by some magic there are other steps besides the ones outlined and printed with the purchase of server. But the main thing about mail is that we are missing the basics. I mean your going to be hard pressed to find ANY e-mail application on the market today, Notes, Exchange, Gmail, Hotmail, Yahoo, iMail or other that does not include basic vacation/out of the office message replies. This is a huge issue for any small business or for that matter any size business that wants to automate things when they are out and I think this is one of my small peeves but certainly worth a listing here.
    5. VPN - We have tried like **** to get the VPN to work thru the Airport as previously noted but we have also connected MacPro with 2 nics, one for net and one for LAN and not been able to connect to the server from outside our network. Here is my largest frustration, we currently run SBS2003 from MSFT and they run flawlessly. I have literally sat with clients in their office during a new setup for SBS and in 3-4 hours we were up and running with minimal system level changes from the guided path. And for Apple to advertise this in the manual and all online materials as being SMB friendly is a complete slap in the face. Now don't confuse my above descriptions of problems we have seen across 5 Leopard builds as being a rant because it's not but seriously I am a network engineer with 10 years in the field working with 20+ product ranges and in our office we only use Mac because of stability and uptime. But OS X 10.5 is not Small Business Friendly at all even with the half hearted attempt at the new System Admin console for SMB users. However that being said I will still push on and try to get all these little bugs worked out and what I would really like to see is some feedback on my issues and I would love to know if anyone else has had similar issues. I really had hoped that 10.5 could help my firm finally push the proper solution (Mac OS X) for our SMB clients but it just isn't there yet.
    Cheers,
    DM

    Thanks for the quick read and response. Do you feel the issue might lie with the fact that it is a Mac Mini? And possibly just not powerful enough to run Leopard Server? I have to say in our trials with MacPro it was like night and day as to how they performed. And if you could elaborate on this "Many VPNs don't play well with NAT so your VPN server should have a direct connection to the public network (preferably firewalled, of course, but not NATted)." Most every SoHo and for that matter uses simple NAT translation for security even our multi thousand dollar Cisco PIX and ASA's are basic NAT devices to start with. How would you put the VPN on public net while keeping the attack surface low for the rest of the services like file, web, mail and print?
    Don't get me wrong I want this to work more than you can imagine. We are so tired of supporting MSFT technologies that cost thousands a year in antivirus, antispyware, antispam and other malware protection for the enterprise. We know that Leopard has great potential but for an integrator, getting this system up and functional is not an easy task. And the worst part of it is every time we have called for support the tech always lets out a sigh when they hear we have run standard setup because they are not allowed to walk us thru the server console to make repairs. And have been told by 3 techs so far that this is a new product and the support avenues are not there for standard since it just supposed to work out of the box. But when it doesn't then ohh well. Which is sorta sad...
    DM

  • SQL Server Setup Error

    Good Evening,
    I've been having an issue today whilst trying to install SQL Server 2012 to a newly built server running Windows Server 2012 R2. Whilst going through the 'Database Engine Configuration' where you assign parts of the installation to different directories.
    We are trying a new method of installing each part of SQL to an SMB file share on our Netapp. After pointing each part of installation to a specific directory and pressing next I receive the error attached
    I can see that it says that you need to give the SQL Server setup account the  Manage Auditing and Security Log policy on the local policy console. I've gone to this policy and added myself (Local Administrator), The server itself, the SQL Server
    Agent account and also the database engine account. I have rebooted the server and tried again running the installation both as myself and Administrator but still get the same error. Please could someone help me with this issue.
    Regards,

    Hello,
    Please read the following article.
    http://msdn.microsoft.com/en-us/library/hh759341.aspx
    Please review security and operating system considerations.
    Hope this helps.
    Regards,
    Alberto Morillo
    SQLCoffee.com

  • How do you setup a server to use multiple DNS servers that are not connect to each other?

    Is there a way to setup a server that connects to two different domains to use the proper DNS server for name resolution?
    Let say there are two DCs: serverA.subdomaina.domain.com and serverB.subdoamainb.domain.com.  The domains are independent and not connected.  Now you need a common server that is connected to both and need to resolve names from both
    domains.
    Is this possible?
    I have setup a server in a workgroup.  One NIC has the subdomaina.domain.com connection specific suffix and the other nic has the subdomainb.domain.com.  Each NIC has the DNS server listed for the domain it is connected to.
    This configuration will resolve FQDNs of one domain but not the other.  This I believe is due to the fact the server only querys one DNS server and doesn't try the other DNS server.
    Is there any way to make the server try another DNS server, if the first one doesn't have the entry?

    Hi,
    Thank you for posting in Windows Server Forum.
    Here adding to the words of “Tim”, a forwarder is a DNS server on a network used to forward DNS queries for external DNS names to DNS servers outside of that network. You can also forward queries according to specific domain names using conditional forwarders.
    A DNS server on a network is designated as a forwarder by having the other DNS servers in the network forward the queries they cannot resolve locally to that DNS server. You can refer information regarding forwarders and how to configure from beneath link.
    Understanding forwarders
    http://technet.microsoft.com/en-us/library/cc782142(v=ws.10).aspx
    Configure a DNS Server to Use Forwarders
    http://technet.microsoft.com/en-us/library/cc754941.aspx
    Hope it helps!
    Regards.

  • HT4938 New mac-mini server setup without keyboard and mouse

    Im trying to use the server app to setup my new mac mini server without mouse and keyboard, but the server is not listed. I have tried using its IP address with no username and the serial number as password but it won't connect. Any ideas?

    You may have a version mismatch. If I recall, setup assistant is OS version dependent so if the refurb is 10.5 and the Mac Pro is 10.6 you will likely not be able to use setup assistant.
    However, just use ARD or Screen Sharing to connect. If the mini is visible on the network and in the ready for setup mode, you can ssh into the machine using the root user and the first 8 digits of the machine serial number. Then you can use the kickstart command to startup the ARD agent on the system. Use these commands while in the SSH session.
    cd /System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Resources
    sudo ./kickstart -activate
    sudo ./kickstart -configure -access -on -privs -all -users <shortname>
    For now, the user will need to be root because there is no user. Then screen share the system to complete the remainder of the initial setup.
    In theory this will work. Works on Xserves, so I believe the minis work the same for initial setup.
    Hope this helps

  • SQL Server Setup Failure 0x84B10001 (SQL 2012 SP2 and SQL 2014 Standard)

    I'm having a problem with SQL Server Setup. I had SQL Server 2012 R2 SP1 installed, and the SP2 installer would fail.
    I decided to just get SQL Server 2014. The setup (and system configuration checker) for that fails with the same error.
    SQL Server Setup failure
    SQL Server Setup has encountered the following error:
    '.', hexadecimal value 0x00, is an invalid character. Line 1, position 231747.
    Error code 0x84B10001
    I found this and other posts about similar problems that point at MSDE being the cause.
    http://social.msdn.microsoft.com/Forums/sqlserver/en-US/bc9f4949-1b45-427c-aa2b-d2222488a13e/problems-installing-sql-server-2012error-code-0x84b10001?forum=sqlexpress
    I definitely had MSDE installed, but I went through the steps to manually remove it and rebooted with no luck.
    /* Don Reynolds */

    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.SqlBrowserExtension.sqlBrowserStopServicePrivateConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.SqlBrowserExtension.sqlBrowserStopServicePrivateConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.SqlBrowserExtension.sqlBrowserStopServicePrivateConfig.xsd' loaded
    into datastore path '/Datastore/ProductSettings/SqlBrowserStopService/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.SetupExtension.SkuPublicConfigObject.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.SetupExtension.SkuPublicConfigObjectDefault.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.SetupExtension.SkuPublicConfigObjectDefault.xml' validated with schema 'Microsoft.SqlServer.Configuration.SetupExtension.SkuPublicConfigObject.xsd' loaded into datastore path '/Datastore/ProductSettings/Sku/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.SetupExtension.SkuPrivateConfigObject.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.SetupExtension.SkuPrivateConfigObjectDefault.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.SetupExtension.SkuPrivateConfigObjectDefault.xml' validated with schema 'Microsoft.SqlServer.Configuration.SetupExtension.SkuPrivateConfigObject.xsd' loaded into datastore path '/Datastore/ProductSettings/Sku/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Repl_ConfigExtension.ReplPrivateSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Repl_ConfigExtension.ReplPrivateDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Repl_ConfigExtension.ReplPrivateDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.Repl_ConfigExtension.ReplPrivateSettings.xsd' loaded into datastore path
    '/Datastore/ProductSettings/Repl/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.RSSHPExtension.SqlRSSHPConfigPublicDefaultSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.RSSHPExtension.SqlRSSHPConfigPublicDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.RSSHPExtension.SqlRSSHPConfigPublicDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.RSSHPExtension.SqlRSSHPConfigPublicDefaultSettings.xsd' loaded into datastore
    path '/Datastore/ProductSettings/SqlRSSHP/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.RSSHPExtension.SqlRSSHPConfigPrivateDefaultSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.RSSHPExtension.SqlRSSHPConfigPrivateDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.RSSHPExtension.SqlRSSHPConfigPrivateDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.RSSHPExtension.SqlRSSHPConfigPrivateDefaultSettings.xsd' loaded into
    datastore path '/Datastore/ProductSettings/SqlRSSHP/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSConfigPublicDefaultSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSConfigPublicDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSConfigPublicDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSConfigPublicDefaultSettings.xsd' loaded into datastore path
    '/Datastore/ProductSettings/SqlRS/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSConfigPrivateDefaultSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSConfigPrivateDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSConfigPrivateDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSConfigPrivateDefaultSettings.xsd' loaded into datastore path
    '/Datastore/ProductSettings/SqlRS/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSDBConfigPrivateDefaultSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSDBConfigPrivateDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSDBConfigPrivateDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.RSExtension.SqlRSDBConfigPrivateDefaultSettings.xsd' loaded into datastore
    path '/Datastore/ProductSettings/SqlRS/DBPrivate'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsPublicSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsPublicDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsPublicDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsPublicSettings.xsd'
    loaded into datastore path '/Datastore/ProductSettings/ManagementTools/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsPrivateSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsPrivateDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsPrivateDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsPrivateSettings.xsd'
    loaded into datastore path '/Datastore/ProductSettings/ManagementTools/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsAdvancedPublicSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsAdvancedPublicDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsAdvancedPublicDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsAdvancedPublicSettings.xsd'
    loaded into datastore path '/Datastore/ProductSettings/ManagementToolsAdvanced/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsAdvancedPrivateSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsAdvancedPrivateDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsAdvancedPrivateDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.ManagementToolsExtension.ManagementToolsAdvancedPrivateSettings.xsd'
    loaded into datastore path '/Datastore/ProductSettings/ManagementToolsAdvanced/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.DistributedReplayExtension.ControllerPrivateSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.DistributedReplayExtension.ControllerPrivateDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.DistributedReplayExtension.ControllerPrivateDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.DistributedReplayExtension.ControllerPrivateSettings.xsd' loaded
    into datastore path '/Datastore/ProductSettings/DReplayController/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.DistributedReplayExtension.ClientPrivateSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.DistributedReplayExtension.ClientPrivateDefaultSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.DistributedReplayExtension.ClientPrivateDefaultSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.DistributedReplayExtension.ClientPrivateSettings.xsd' loaded into
    datastore path '/Datastore/ProductSettings/DReplayClient/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterDiskPrivateConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterDiskPrivateConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.ClusterDiskPrivateConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.ClusterDiskPrivateConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/ClusterDisk/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterDiskPublicConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterDiskPublicConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.ClusterDiskPublicConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.ClusterDiskPublicConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/ClusterDisk/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterGroupPrivateConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterGroupPrivateConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.ClusterGroupPrivateConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.ClusterGroupPrivateConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/ClusterGroup/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterGroupPublicConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterGroupPublicConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.ClusterGroupPublicConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.ClusterGroupPublicConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/ClusterGroup/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterIPAddressPrivateConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterIPAddressPrivateConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.ClusterIPAddressPrivateConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.ClusterIPAddressPrivateConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/ClusterIPAddresses/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterIPAddressPublicConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterIPAddressPublicConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.ClusterIPAddressPublicConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.ClusterIPAddressPublicConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/ClusterIPAddresses/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.FailoverInstanceNamePrivateConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.FailoverInstanceNamePrivateConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.FailoverInstanceNamePrivateConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.FailoverInstanceNamePrivateConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/FailOverClusterName/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.FailoverInstanceNamePublicConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.FailoverInstanceNamePublicConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.FailoverInstanceNamePublicConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.FailoverInstanceNamePublicConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/FailoverClusterName/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodePrivateConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodePrivateConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodePrivateConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodePrivateConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/ClusterNode/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodePublicConfig.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodePublicConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodePublicConfig.xml' validated with schema 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodePublicConfig.xsd' loaded into datastore path '/Datastore/ProductSettings/ClusterNode/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.SlpExtension.SQLServerSCPPrivateSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.SlpExtension.SQLServerSCPPrivateSettings.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.SlpExtension.SQLServerSCPPrivateSettings.xml' validated with schema 'Microsoft.SqlServer.Configuration.SlpExtension.SQLServerSCPPrivateSettings.xsd' loaded into datastore path '/Datastore/ProductSettings/SQLServerSCP/Private'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodesStatusPublicConfig.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.Cluster.ClusterNodesStatusPublicConfig.xml' loaded into datastore path '/Datastore/ProductSettings/ClusterNodesStatus/Public'
    (01) 2014-07-02 10:52:57 Slp: Reading schema resource 'Microsoft.SqlServer.Configuration.ASExtension.ASSPIInputSettings.xsd'
    (01) 2014-07-02 10:52:57 Slp: Reading XML resource 'Microsoft.SqlServer.Configuration.ASExtension.ASSPIInputSettingsDefaults.xml'
    (01) 2014-07-02 10:52:57 Slp: Document 'Microsoft.SqlServer.Configuration.ASExtension.ASSPIInputSettingsDefaults.xml' validated with schema 'Microsoft.SqlServer.Configuration.ASExtension.ASSPIInputSettings.xsd' loaded into datastore path '/Datastore/ProductSettings/ASSIP/Public'
    (01) 2014-07-02 10:52:57 Slp: Completed Action: LoadPackageDatastoreObjects, returned True
    (01) 2014-07-02 10:52:57 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:57 Slp: Running Action: InitializeInputSettingStore
    (01) 2014-07-02 10:52:57 Slp: Completed Action: InitializeInputSettingStore, returned True
    (01) 2014-07-02 10:52:57 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:57 Slp: Running Action: InitializeRoleService
    (01) 2014-07-02 10:52:57 Slp: Loading role: SPI_AS_NewFarm
    (01) 2014-07-02 10:52:58 Slp: Loading role: SPI_AS_ExistingFarm
    (01) 2014-07-02 10:52:58 Slp: Loading role: AllFeatures_WithDefaults
    (01) 2014-07-02 10:52:58 Slp: Completed Action: InitializeRoleService, returned True
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Running Action: ProcessChainerCommandLineArguments
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: WORKFLOW
    (01) 2014-07-02 10:52:58 Slp: Value specified: RUNRULES
    (01) 2014-07-02 10:52:58 Slp: New setting source: CommandLine; previous setting source: NotSpecified
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: TIMESTAMP
    (01) 2014-07-02 10:52:58 Slp: Value specified: 20140702_105236
    (01) 2014-07-02 10:52:58 Slp: New setting source: CommandLine; previous setting source: Default
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: LOGMARKER
    (01) 2014-07-02 10:52:58 Slp: Value specified:
    (01) 2014-07-02 10:52:58 Slp: New setting source: CommandLine; previous setting source: Default
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: MEDIASOURCE
    (01) 2014-07-02 10:52:58 Slp: Value specified: R:\
    (01) 2014-07-02 10:52:58 Slp: New setting source: CommandLine; previous setting source: NotSpecified
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: INSTALLMEDIAPATH
    (01) 2014-07-02 10:52:58 Slp: Value specified: R:\x64\setup\
    (01) 2014-07-02 10:52:58 Slp: New setting source: CommandLine; previous setting source: NotSpecified
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: ENU
    (01) 2014-07-02 10:52:58 Slp: Value specified: True
    (01) 2014-07-02 10:52:58 Slp: New setting source: CommandLine; previous setting source: Default
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: MEDIALAYOUT
    (01) 2014-07-02 10:52:58 Slp: Value specified: Full
    (01) 2014-07-02 10:52:58 Slp: New setting source: CommandLine; previous setting source: Default
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: ACTION
    (01) 2014-07-02 10:52:58 Slp: Value specified: RUNRULES
    (01) 2014-07-02 10:52:58 Slp: New setting source: CommandLine; previous setting source: NotSpecified
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: RULES
    (01) 2014-07-02 10:52:58 Slp: Value specified: SCCCheckRules
    (01) 2014-07-02 10:52:58 Slp: New setting source: CommandLine; previous setting source: Default
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Completed Action: ProcessChainerCommandLineArguments, returned True
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Running Action: ProcessMediaChainerConfigFileArguments
    (01) 2014-07-02 10:52:58 Slp: Procssing media configuration file R:\x64\setup\..\DefaultSetup.ini.
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Setting: PID
    (01) 2014-07-02 10:52:58 Slp: New setting source: ConfigFile; previous setting source: NotSpecified
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Completed Action: ProcessMediaChainerConfigFileArguments, returned True
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Running Action: ProcessChainerConfigFileArguments
    (01) 2014-07-02 10:52:58 Slp: Completed Action: ProcessChainerConfigFileArguments, returned True
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Running Action: ProcessSlipstreamParameters
    (01) 2014-07-02 10:52:58 Slp: Completed Action: ProcessSlipstreamParameters, returned True
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Skipping Action: SetRoleAndUIModeForExpressMedia
    (01) 2014-07-02 10:52:58 Slp: Action is being skipped due to the following restrictions:
    (01) 2014-07-02 10:52:58 Slp: Condition "IsMediaExpress" did not pass as it returned false and true was expected.
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Running Action: InitializeRetryHandler
    (01) 2014-07-02 10:52:58 Slp: Completed Action: InitializeRetryHandler, returned True
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Running Action: ExecuteBootstrapProcessInputSettings
    (01) 2014-07-02 10:52:58 Slp: Workflow to execute: 'BOOTSTRAPPROCESSINPUTSETTINGS'
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Running Action: StartSqmSession
    (01) 2014-07-02 10:52:58 Slp: Sco: Attempting to create base registry key HKEY_LOCAL_MACHINE, machine
    (01) 2014-07-02 10:52:58 Slp: Sco: Attempting to open registry subkey Software\Microsoft\Microsoft SQL Server\120
    (01) 2014-07-02 10:52:58 Slp: Sco: Attempting to get registry value CustomerFeedback
    (01) 2014-07-02 10:52:58 Slp: SQM Service: Sqm does not have active session.
    (01) 2014-07-02 10:52:58 Slp: SQM is opted-out by command line parameter /SQMREPORTING or registry key setting, SQM session is closed
    (01) 2014-07-02 10:52:58 Slp: Completed Action: StartSqmSession, returned True
    (01) 2014-07-02 10:52:58 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:58 Slp: Running Action: ValidateChainerSetting
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : Compute new PID
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : Read lcid 1033 from CultureInfo
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:58 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: Completed Action: ValidateChainerSetting, returned True
    (01) 2014-07-02 10:52:59 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:59 Slp: Running Action: ProcessFeatureCommandLineArguments
    (01) 2014-07-02 10:52:59 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:59 Slp: Completed Action: ProcessFeatureCommandLineArguments, returned True
    (01) 2014-07-02 10:52:59 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:59 Slp: Running Action: ProcessMediaFeatureConfigFileArguments
    (01) 2014-07-02 10:52:59 Slp: Procssing media configuration file R:\x64\setup\..\DefaultSetup.ini.
    (01) 2014-07-02 10:52:59 Slp: ----------------------------------------
    (01) 2014-07-02 10:52:59 Slp: Completed Action: ProcessMediaFeatureConfigFileArguments, returned True
    (01) 2014-07-02 10:52:59 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:59 Slp: Running Action: ProcessFeatureConfigFileArguments
    (01) 2014-07-02 10:52:59 Slp: Completed Action: ProcessFeatureConfigFileArguments, returned True
    (01) 2014-07-02 10:52:59 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:59 Slp: Running Action: ValidateSettingsAgainstScenario
    (01) 2014-07-02 10:52:59 Slp: Scenario: RunRules
    (01) 2014-07-02 10:52:59 Slp: Completed Action: ValidateSettingsAgainstScenario, returned True
    (01) 2014-07-02 10:52:59 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:59 Slp: Running Action: FinalCalculateSettings
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid is normalizing input pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : NormalizePid found a pid containing dashes, assuming pid is normalized, output pid
    (01) 2014-07-02 10:52:59 Slp: -- PidInfoProvider : Use cached PID
    (01) 2014-07-02 10:52:59 Slp: Completed Action: FinalCalculateSettings, returned True
    (01) 2014-07-02 10:52:59 Slp: Completed Action: ExecuteBootstrapProcessInputSettings, returned True
    (01) 2014-07-02 10:52:59 Slp: Completed Action: ExecuteBootstrapAfterExtensionsLoaded, returned True
    (01) 2014-07-02 10:52:59 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:52:59 Slp: Running Action: RunRemoteDiscoveryAction
    (01) 2014-07-02 10:52:59 Slp: Running discovery on local machine
    (01) 2014-07-02 10:53:03 Slp: Error: Action "Microsoft.SqlServer.Configuration.SetupExtension.RunDiscoveryAction" threw an exception during execution.
    (01) 2014-07-02 10:53:03 Slp: Microsoft.SqlServer.Setup.Chainer.Workflow.ActionExecutionException: '.', hexadecimal value 0x00, is an invalid character. Line 1, position 231747. ---> Microsoft.SqlServer.Chainer.Infrastructure.ChainerInfrastructureException:
    '.', hexadecimal value 0x00, is an invalid character. Line 1, position 231747. ---> System.Xml.XmlException: '.', hexadecimal value 0x00, is an invalid character. Line 1, position 231747.
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlTextReaderImpl.Throw(Exception e)
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlTextReaderImpl.ThrowInvalidChar(Int32 pos, Char invChar)
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlTextReaderImpl.ParseNumericCharRefInline(Int32 startPos, Boolean expand, BufferBuilder internalSubsetBuilder, Int32& charCount, EntityType& entityType)
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlTextReaderImpl.ParseNumericCharRef(Boolean expand, BufferBuilder internalSubsetBuilder, EntityType& entityType)
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlTextReaderImpl.HandleEntityReference(Boolean isInAttributeValue, EntityExpandType expandType, Int32& charRefEndPos)
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlTextReaderImpl.ParseAttributeValueSlow(Int32 curPos, Char quoteChar, NodeData attr)
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlTextReaderImpl.ParseAttributes()
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlTextReaderImpl.ParseElement()
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlTextReaderImpl.ParseElementContent()
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlLoader.LoadNode(Boolean skipOverWhitespace)
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlLoader.LoadDocSequence(XmlDocument parentDoc)
    (01) 2014-07-02 10:53:03 Slp:    at System.Xml.XmlDocument.Load(XmlReader reader)
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Chainer.Infrastructure.DataStoreService.LoadXmlDocument(String xml, XmlSchema schema, String namespacePrefix, String namespaceUri, String rootPath)
    (01) 2014-07-02 10:53:03 Slp:    --- End of inner exception stack trace ---
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Chainer.Infrastructure.DataStoreService.LoadXmlDocument(String xml, XmlSchema schema, String namespacePrefix, String namespaceUri, String rootPath)
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Chainer.Infrastructure.DataStoreService.LoadXmlDocument(XmlDocument doc, XmlSchema schema, String namespacePrefix, String namespaceUri, String rootPath)
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Chainer.Infrastructure.SqlDiscoveryDatastoreInterface.LoadData(IEnumerable`1 machineNames, String discoveryDocRootPath, String clusterDiscoveryDocRootPath)
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Configuration.SetupExtension.RunDiscoveryAction.ExecuteAction(String actionId)
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Chainer.Infrastructure.Action.Execute(String actionId, TextWriter errorStream)
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionInvocation.<>c__DisplayClasse.<ExecuteActionWithRetryHelper>b__b()
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionInvocation.ExecuteActionHelper(ActionWorker workerDelegate)
    (01) 2014-07-02 10:53:03 Slp:    --- End of inner exception stack trace ---
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionInvocation.ExecuteActionHelper(ActionWorker workerDelegate)
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionInvocation.ExecuteActionWithRetryHelper(WorkflowObject metaDb, ActionKey action, ActionMetadata actionMetadata, TextWriter statusStream)
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionInvocation.InvokeAction(WorkflowObject metabase, TextWriter statusStream)
    (01) 2014-07-02 10:53:03 Slp:    at Microsoft.SqlServer.Setup.Chainer.Workflow.PendingActions.InvokeActions(WorkflowObject metaDb, TextWriter loggingStream)
    (01) 2014-07-02 10:53:03 Slp: Received request to add the following file to Watson reporting: c:\temp\tmpFEEB.tmp
    (01) 2014-07-02 10:53:03 Slp: The following is an exception stack listing the exceptions in outermost to innermost order
    (01) 2014-07-02 10:53:03 Slp: Inner exceptions are being indented
    (01) 2014-07-02 10:53:03 Slp:
    (01) 2014-07-02 10:53:03 Slp: Exception type: Microsoft.SqlServer.Chainer.Infrastructure.ChainerInfrastructureException
    (01) 2014-07-02 10:53:03 Slp:     Message:
    (01) 2014-07-02 10:53:03 Slp:         '.', hexadecimal value 0x00, is an invalid character. Line 1, position 231747.
    (01) 2014-07-02 10:53:03 Slp:     HResult : 0x84b10001
    (01) 2014-07-02 10:53:03 Slp:         FacilityCode : 1201 (4b1)
    (01) 2014-07-02 10:53:03 Slp:         ErrorCode : 1 (0001)
    (01) 2014-07-02 10:53:03 Slp:     Stack:
    (01) 2014-07-02 10:53:03 Slp:         at Microsoft.SqlServer.Chainer.Infrastructure.DataStoreService.LoadXmlDocument(String xml, XmlSchema schema, String namespacePrefix, String namespaceUri, String rootPath)
    (01) 2014-07-02 10:53:03 Slp:         at Microsoft.SqlServer.Chainer.Infrastructure.DataStoreService.LoadXmlDocument(XmlDocument doc, XmlSchema schema, String namespacePrefix, String namespaceUri, String rootPath)
    (01) 2014-07-02 10:53:03 Slp:         at Microsoft.SqlServer.Chainer.Infrastructure.SqlDiscoveryDatastoreInterface.LoadData(IEnumerable`1 machineNames, String discoveryDocRootPath, String clusterDiscoveryDocRootPath)
    (01) 2014-07-02 10:53:03 Slp:         at Microsoft.SqlServer.Configuration.SetupExtension.RunDiscoveryAction.ExecuteAction(String actionId)
    (01) 2014-07-02 10:53:03 Slp:         at Microsoft.SqlServer.Chainer.Infrastructure.Action.Execute(String actionId, TextWriter errorStream)
    (01) 2014-07-02 10:53:03 Slp:         at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionInvocation.<>c__DisplayClasse.<ExecuteActionWithRetryHelper>b__b()
    (01) 2014-07-02 10:53:03 Slp:         at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionInvocation.ExecuteActionHelper(ActionWorker workerDelegate)
    (01) 2014-07-02 10:53:03 Slp:     Inner exception type: System.Xml.XmlException
    (01) 2014-07-02 10:53:03 Slp:         Message:
    (01) 2014-07-02 10:53:03 Slp:                 '.', hexadecimal value 0x00, is an invalid character. Line 1, position 231747.
    (01) 2014-07-02 10:53:03 Slp:         HResult : 0x80131940
    (01) 2014-07-02 10:53:03 Slp:         Stack:
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlTextReaderImpl.Throw(Exception e)
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlTextReaderImpl.ThrowInvalidChar(Int32 pos, Char invChar)
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlTextReaderImpl.ParseNumericCharRefInline(Int32 startPos, Boolean expand, BufferBuilder internalSubsetBuilder, Int32&
    charCount, EntityType& entityType)
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlTextReaderImpl.ParseNumericCharRef(Boolean expand, BufferBuilder internalSubsetBuilder, EntityType& entityType)
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlTextReaderImpl.HandleEntityReference(Boolean isInAttributeValue, EntityExpandType expandType, Int32& charRefEndPos)
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlTextReaderImpl.ParseAttributeValueSlow(Int32 curPos, Char quoteChar, NodeData attr)
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlTextReaderImpl.ParseAttributes()
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlTextReaderImpl.ParseElement()
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlTextReaderImpl.ParseElementContent()
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlLoader.LoadNode(Boolean skipOverWhitespace)
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlLoader.LoadDocSequence(XmlDocument parentDoc)
    (01) 2014-07-02 10:53:03 Slp:                 at System.Xml.XmlDocument.Load(XmlReader reader)
    (01) 2014-07-02 10:53:03 Slp:                 at Microsoft.SqlServer.Chainer.Infrastructure.DataStoreService.LoadXmlDocument(String xml, XmlSchema schema, String namespacePrefix,
    String namespaceUri, String rootPath)
    (01) 2014-07-02 10:53:08 Slp: Watson Bucket 2
     Original Parameter Values
    (01) 2014-07-02 10:53:08 Slp: Parameter 0 : SQL Server
    2014@RTM@
    (01) 2014-07-02 10:53:08 Slp: Parameter 1 : Microsoft.SqlServer.Chainer.Infrastructure.DataStoreService.LoadXmlDocument
    (01) 2014-07-02 10:53:08 Slp: Parameter 2 : System.Xml.XmlTextReaderImpl.Throw
    (01) 2014-07-02 10:53:08 Slp: Parameter 3 :
    Microsoft.SqlServer.Chainer.Infrastructure.ChainerInfrastructureException@1201@1
    (01) 2014-07-02 10:53:08 Slp: Parameter 4 :
    System.Xml.XmlException@-2146232000
    (01) 2014-07-02 10:53:08 Slp: Parameter 5 : RunRemoteDiscoveryAction
    (01) 2014-07-02 10:53:08 Slp:
     Final Parameter Values
    (01) 2014-07-02 10:53:08 Slp: Parameter 0 : SQL Server
    2014@RTM@
    (01) 2014-07-02 10:53:08 Slp: Parameter 1 : 0xDBE3EAAC
    (01) 2014-07-02 10:53:08 Slp: Parameter 2 : 0x066FCAFD
    (01) 2014-07-02 10:53:08 Slp: Parameter 3 :
    0xDF039760@1201@1
    (01) 2014-07-02 10:53:08 Slp: Parameter 4 : 0x5539C151
    (01) 2014-07-02 10:53:08 Slp: Parameter 5 : RunRemoteDiscoveryAction
    (01) 2014-07-02 10:53:09 Slp: Sco: Attempting to write hklm registry key Microsoft SQL Server to file C:\Program Files\Microsoft SQL Server\120\Setup Bootstrap\Log\20140702_105236\Registry_SOFTWARE_Microsoft_Microsoft SQL Server.reg_
    (01) 2014-07-02 10:53:09 Slp: Sco: Attempting to write hklm registry key Uninstall to file C:\Program Files\Microsoft SQL Server\120\Setup Bootstrap\Log\20140702_105236\Registry_SOFTWARE_Microsoft_Windows_CurrentVersion_Uninstall.reg_
    (01) 2014-07-02 10:53:09 Slp: Sco: Attempting to write hklm registry key MSSQLServer to file C:\Program Files\Microsoft SQL Server\120\Setup Bootstrap\Log\20140702_105236\Registry_SOFTWARE_Microsoft_MSSQLServer.reg_
    (01) 2014-07-02 10:53:09 Slp: Sco: Attempting to write hklm registry key Microsoft SQL Server to file C:\Program Files\Microsoft SQL Server\120\Setup Bootstrap\Log\20140702_105236\Registry_SOFTWARE_Wow6432Node_Microsoft_Microsoft SQL Server.reg_
    (01) 2014-07-02 10:53:09 Slp: Sco: Attempting to write hklm registry key Uninstall to file C:\Program Files\Microsoft SQL Server\120\Setup Bootstrap\Log\20140702_105236\Registry_SOFTWARE_Wow6432Node_Microsoft_Windows_CurrentVersion_Uninstall.reg_
    (01) 2014-07-02 10:53:09 Slp: Sco: Attempting to write hklm registry key MSSQLServer to file C:\Program Files\Microsoft SQL Server\120\Setup Bootstrap\Log\20140702_105236\Registry_SOFTWARE_Wow6432Node_Microsoft_MSSQLServer.reg_
    (01) 2014-07-02 10:53:10 Slp: '.', hexadecimal value 0x00, is an invalid character. Line 1, position 231747.
    (01) 2014-07-02 10:53:10 Slp: Watson bucket for exception based failure has been created
    (01) 2014-07-02 10:53:10 Slp: Sco: Attempting to create base registry key HKEY_LOCAL_MACHINE, machine
    (01) 2014-07-02 10:53:10 Slp: Sco: Attempting to open registry subkey Software\Microsoft\Microsoft SQL Server\120
    (01) 2014-07-02 10:53:10 Slp: Sco: Attempting to get registry value EnableErrorReporting
    (01) 2014-07-02 10:53:10 Slp: WER: Successfully read app consent from registry Software\Microsoft\Microsoft SQL Server\120\EnableErrorReporting=.
    (01) 2014-07-02 10:53:10 Slp: WER: Application level consent value '' was mapped to consent status 'WerConsentNotAsked'
    (01) 2014-07-02 10:53:12 Slp: WER: Result of the submission:: 'WerReportCancelled'
    (01) 2014-07-02 10:53:12 Slp: WER: Submitted 1 of 1 failures to the Watson data repository
    (01) 2014-07-02 10:53:12 Slp:
    (01) 2014-07-02 10:53:12 Slp: ----------------------------------------------------------------------
    (01) 2014-07-02 10:53:12 Slp:
    (01) 2014-07-02 10:53:12 Slp: Error result: -2068774911
    (01) 2014-07-02 10:53:12 Slp: Result facility code: 1201
    (01) 2014-07-02 10:53:12 Slp: Result error code: 1
    (01) 2014-07-02 10:53:12 Slp: SQM Service: Sqm does not have active session.
    /* Don Reynolds */

Maybe you are looking for

  • Why does my iPhone 5 keep telling me that storage is almost full?

    Since I upgraded my iPhone 5 to iOS 7 it has been acting strange. I keep getting messages telling me that the storage is almost full yet when I check there is over 358mb of free space. I have tried restoring my iPhone but I still keep getting these e

  • Facebook event overload in iOS 6 Calendar.

    I like the idea of easily having events that I am going to synced in my Calendar, but, apparently, it adds events that you've been invited to even if you haven't decided to go.  I don't need my Calendar filled with potential events, I only want the o

  • Do I begin by scanning my illustratration in a pdf and then save it as a png on illustrator?

    Do I begin by scanning my artwork as pdf and then saving it as a png on illustrator?

  • Won't play in edit mode

    In Audition 1.5 multitrack view plays fine and all functions are usable, however when I try to edit a waveform, the stop, play, pause, play from cursor, and play looped are all greyed out and unusable. I've tried pressing the spacebar as well, but no

  • JTextPane first line read only

    Hi all! I'm a beginner in java programming, that said im trying to make a simple text editor (who isn't?), it will be a part of another larger application, nevertheless this editor is a main component, just need some simple editing tips. I want to us