Driver for Canon c5035i on Mac OSX 10.10

Hi,
I am working on OS X 10.10 on  and I cannot connect to a Canon C5035i printer. I have downloaded each and every driver I could on the Canon website but the printer is not recognized. Even by pointing it with its IP address, the driver is not recognized.
Can anyone help me?
Thanks and regards
Max

Tki.design wrote:
But when I try to print a document, it appears for 1 second in my printing list then disappears and no print is done...
This can happen when using the Postscript driver but the C5035 does not have the Postscript kit. So even though you can see the toner levels after adding the printer using the Postscript drivers, it does not mean it supports Postscript. To check if the printer has the Postscript option installed, you can go to the copier and press the Counter Check button. Then on the touch screen, press Device Configuration. You may need to scroll down a page or two. You will see the UFR2 option and possibly PCL. If you don't see PS then it does not have it. So in this case you would need to use the UFR2 driver. Here is a link to the latest UFR2 driver for 10.10.
If the C5035 does have the Postscript option then the other cause for the print job failing is the protocol being used for the print queue. The Canon drivers support the LPD and HP Jetdirect protocols - not IPP. And there has been some users who have found that the LPD protocol does not allow them to print, while the HP Jetdirect protocol has always worked. So if you cannot remember which protocol you used when creating the printer, then remove the printer and add again, selecting HP Jetdirect-Socket for the protocol.
The last thing that can stop the print job is Dept ID Management. This is a security setting in the copier that requires you to enter an ID/PIN to make a copy. If this is enabled for printing also, then you have to enter an ID/PIN for all print jobs, otherwise the print job will disappear. To check if you need to enable this setting, open Printers & Scanners and select the C5035. Then click on Options & Supplies and then the Utilities tab. Then click on Open Printer Utility. This will open the Canon Printer Utility for the respective driver. Here you will see a Printer Information button. Press this to open another window which will show if Dept ID Management is enabled. If it is, then it explains why you prints have been failing and you will need to configure the driver to use an ID/PIN in order to print. Reply if you need help with configuring the driver to use Dept ID management.
If there is no mention of Dept ID in the Printer Information window, and the C5035 does have Postscript kit and you did use the HP Jetdirect protocol, and it still fails to print, then please reply.

Similar Messages

  • Help formatting Hard Drive for best compatibility with Mac OSX 10.5!

    I have a 1TB hard drive that I recently purchased. I would like for format it for best compatibility with Leopard. I must be doing something wrong because everything I try, I get an error.
    Here's the details of my drive.
    What do I need to do in Disk Utility?
    Disk Description : WL1000GS A1672 Media
    Total Capacity : 931.5 GB (1,000,204,886,016 Bytes)
    Connection Bus : USB
    Write Status : Read/Write
    Connection Type : External
    S.M.A.R.T. Status : Not Supported
    USB Serial Number : 240077140FFF
    Partition Map Scheme : Master Boot Record
    Main Partition (Only managed to get it's name to CORY.):
    Mount Point : /Volumes/CORY
    Capacity: 931.5 GB (1,000,204,853,760 Bytes)
    Format : MS-DOS (FAT32)
    Available : 931.3 GB (999,959,166,976 Bytes)
    Owners Enabled : No
    Used : 1.4 MB (1,507,328 Bytes)
    Number of Folders : 0
    Number of Files : 0

    Looks like that's working. My problem was I didn't select GUID Scheme. Thanks.
    EDIT: Yup that did the trick. Thanks so much.

  • OSX Yosemite driver for Canon LBP3000

    OSX Yosemite driver for Canon LBP3000 needed. When will one be available?

    Hi smukhi!
     I will be glad to assist you.  The driver is now available for the commercial release of the OS X 10.10 (Yosemite) driver.  I recommend uninstalling the previous driver before installing the latest driver.  To uninstall the driver, please follow the instructions below:
    1. Click the [Printers & Scanners] icon in [System Preferences].
    2.Select the printer you use on [Printers], then click [-].
    3. Delete the printers that are registered, then close the [Print & Scan] dialog box.
    4. Open Finder application of your Mac OS X.
    5. Select [Go] → [Go to Folder] from the menu bar.
    6. Enter the following folder locations, click [Go], then delete the files and folders.
    Delete Example: You can delete files and folders by dragging them to the [Trash] icon in the Dock.
    Location
    Files and folders to delete
    /Library/Printers/Canon/
    CUPSCAPT
    /Library/LaunchAgents/
    jp.co.canon.CUPSCAPT.BG.plist
    /Library/Printers/PPDs/
    Contents/Resources/
    Delete all the following files in the folders.
    CNMCxxxAUS.ppd.gz
    (xxx is a model name starting with [LBP].)
    When the [Authenticate] dialog box is displayed
    Enter the administrator's name and password, and then click [OK].
    7. Close all open windows.
    8. Restart your computer and empty the Trash Bin.
    The printer driver is uninstalled.
    Next, go to the imageCLASS LBP6000 - Drivers & Software page, and then download the file CAPT Printer Driver Ver.3.67 for Mac OS X 10.5/10.6/10.7/... listed under the [Recommended for You] section.
    After installing the printer, please follow the instructions below to add the printer:
    1. Click the [Printers & Scanners] icon in [System Preferences].
    2. Click [+].
    3. Click [Default], and then select the printer to be used from the printer list.
    4. Select [Select Printer Software] from [Print Using].
    5. Select the printer to be used from [Printer Software], and then click [OK].
    6. Click [Add].
    7. Make sure that the printer to be used is displayed, and then close the [Print & Scan] dialog box.
    The printer registration is now completed.
    I hope this information is helpful to you.  Should you need further assistance, please contact us at 1-800-OK-CANON (1-800-652-2666).
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • I need a driver for canon image Class LBP6000 for Mac Mini Yosemite

    I need a driver for canon image Class LBP6000 for Mac Mini Yosemite

    Go to: > http://www.usa.canon.com/cusa/consumer/products/printers_multifunction/laser_pri nters/imageclass_lbp6000#DriversAndSoftware
    It does not look like the Canon driver has change from Mavericks to Yosemite.
    If you just updated from Mavercks to Yosemite, see > OS X Mavericks: Reset the printing system
    If you have a new or clean install of Yosemite, see  > OS X Mavericks: Set up a printer

  • Need driver for canon mg 5250 as scanner is not working with version 10.7. Can you please help me to find the driver so scanner works with WIFI?

    need driver for canon mg 5250 as scanner is not working with version 10.7. Lion. Can you please help me to find the driver so scanner works with WIFI?

    Try with the latest Apple driver package for Canon (released 15th Feb):
    http://support.apple.com/kb/DL899
    This solved my problem with the printing.

  • Can I use my late 2006 mac mini as an external drive for my late 2012 mac mini?

    I have a (late 2006) Mac mini that I would like to use as an external drive for my (late 2012) Mac mini.  Is this possible and can anyone suggest what cables would be needed.  I am aware that the ports are very different i.e firewire and thunderbolt.  Thanks in advance!

    - You can boo the old Mac in Targe Disk Mode and connect the two via FireWire (FW) You will need a FW 400 to FW 800 cable or a FW 800 or FW 400 cable and appropriate adopters
    How to use and troubleshoot FireWire target disk mode - Apple Support
    - Use the old Mac normally and setup Disk Sharing and access the old Mac via the network. The old Mac's disk will show up  under Devices on the new Mac. One you set up the old Mac yo do not need mouse or keyboard or monitor. You can also setup Screen sharing and actually use the old Mac from the new Mac.
    - Remove the HD from the old Mac and place it in an external USB enclosure of dock and connect it to the new Mac

  • DVD/Lightscribe drive for new (late 2010 Mac Pro?

    Does anyone know a source for an internal DVD w/ Lightscribe drive for a late 2010 Mac Pro? I want to install it in the second drive bay. I got one from OWC, but the depth of the DVD drawer was about twice that of the original drive that came with the Mac Pro. It would have been able to fit through the drop cover on the front of the Pro, but would not clear the internal rack components. It fit in the rack nicely with the 4 screws lining up properly, but would then not open more than about an eighth of an inch before hitting the internal rack frame, causing it to close. Thanks.

    Bummer! The instructions included with the drive did not mention thi. When I called OWC customer service she said that sometimes you had to remove the bezel from the Mac. I told her the Pro had no bezel. She said that the drive info did not specifically say it would fit a 2010 Pro a d gave me a RMA.'nmh bad for not questioning further. Thanks.

  • Need Photoshop Elements RAW plugin for Canon 70D using MAC

    Need Photoshop Elements RAW plugin for Canon 70D using MAC - please advise where I can find it to download. Thanks.

    To work with the Canon 70D, you will need Camera Raw version 8.2 or later:
    http://helpx.adobe.com/creative-suite/kb/camera-raw-plug-supported-cameras.html
    In order to work with this version of Camera Raw, you will need Photoshop Elements 12:
    http://helpx.adobe.com/x-productkb/global/camera-raw-compatible-applications.html
    If you do not have Photoshop Elements 12, you can use the DNG converter to convert the CR2 files to DNG, which will then work in whatever version of Photoshop Elements you have:
    Windows: https://www.adobe.com/support/downloads/product.jsp?product=106&platform=Windows
    Mac: http://www.adobe.com/support/downloads/product.jsp?product=106&platform=Macintosh

  • Which version of ACR for CS4 on Intel Mac, OSX 10.6.8?

    Which version of ACR for CS4 on Intel Mac, OSX 10.6.8?

    Moving this discussion to the Adobe Camera RAW forum.  You may want to review the updates available at http://www.adobe.com/support/downloads/product.jsp?product=106&platform=Macintosh.

  • Can't install win7 scanner driver for canon pixma mp260, help please !!!

    can't install win7 scanner driver for canon pixma mp260, help please !!!

    HOW CAN I FIX MY PIXMA CANON WITH OUT THE CD

  • Missing raw file driver for Canon S90

    I miss raw file driver for Canon S90. The software delivered with the camera works, but it doesn't work in finder, Aperure and so on, just in Canons own software. When will the driver be available for SL?

    Apple hasn't said anything about it, but they're always quiet on everything (I think this works to their advantage for new products, but it works to their detriment for product updates.)
    Anyway, they recently released the latest Camera RAW update and surprised a lot of people by not including the S90. Adobe had problems with the S90 -- images would "load" but looked poor. I can only guess Apple also had problems and decided to push it to a later date rather than hold up the whole stack of RAW camera updates people had been waiting on (typically they release an update with support for a list of cameras).

  • Code for face recognition on mac osx using OpenCV

    Hi,
    I am writing a program for face detection on mac osx and I am using OpenCV. I am following the steps given on this link:
    http://iphone-cocoa-objectivec.blogspot.com/2009/01/using-opencv-for-mac-os-in-xcode.html
    There are three codes given for this program. The first code runs smoothly. In the second code there is no error in the compilation, it is successful. But it is not showing any output. As per the program it should open a new window. That window would store the picture taken from the camera.
    In the debugger console window the following error appears.
    OpenCV ERROR: Internal error (couldnt create new video channel)
    in function icvOpenCamera_QT, /Users/david/Work/Development/Net/opencv/xcode/../otherlibs/highgui/cvcap_qt.cpp(954)
    Terminating the application...
    /Users/david/Work/Development/Net/opencv/xcode/../cxcore/src/cxerror.cpp:360: failed assertion `0'
    Please help……
    Thanks and regards
    Prateek Chaubey

    I don't see what this has to do with Alchemy, or any Adobe product at all even!

  • Is it possible to select a permanent font and colour for my emails on mac OSX 10.9.1

    Is it possible to select a permanent font and colour for my emails on mac OSX 10.9.1

    Sadly that doesn't work, or I cant make it work for text only signature

  • Unable to install a software driver for Canon film scanner on mac OSX 10.6

    I am unable to install a software driver for a Canon film scanner FS4000US. I have downloaded it from Canon then open the package click the install and it asks for a location namely the Applications folder. Then it says it has been installed re -start etc, but still no driver.
    I am using Mac OS 10.6. Any suggestions greatly received. I have repaired/disk and permissions and it still does not work.

    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
    Select "/var/log/install.log" from the file list. Post the messages from the last installation attempt, starting from the time when you launched the Installer or Software Update.
    Post the log text, please, not a screenshot. If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
    Important: Some private information, such as your name, may appear in the log. Edit it out by search-and-replace in a text editor before posting.

  • HT3669 Latest Mac OS Update Driver for Canon 9500 Pro causes text lines all to be printed over the first letter of the line?

    Anyone know how I can 'fix' the Mac OS printer driver for the Canon 9500 Pro - all my text lines end up with the whole line being printed over the first character of the line of text when printing PDFs. It has ruined a lot of work.

    I'd try this:
    Delete the current printer (reset the print system) Mac OS X: How to reset the printing system
    Delete all other Canon software and utilities from your computer.
    Do a factory reset on your printer
    Use Software Update to download the driver from Apple.
    Don't reinstall any other Canon Utilities.
    Make sure you don't have something mechanical stopping the paper from advancing.
    If the problem is really the driver, then you could look in Gutenprint for a different driver. Gutenprint for Mac OS X

Maybe you are looking for