Driver for PCMCIA-CAN series 2 card needed

Looking for the driver for the PCMCIA-CAN series 2 card.......
Solved!
Go to Solution.

Not sure what version is needed, but this may get you started:
http://search.ni.com/nisearch/app/main/p/ap/tech/pg/1/sn/ssnav:sup,catnav:du,n13:hardwareDriver,n8:2...
-AK2DM
~~~~~~~~~~~~~~~~~~~~~~~~~~
"It’s the questions that drive us.”
~~~~~~~~~~~~~~~~~~~~~~~~~~

Similar Messages

I use labview 8.0 and i can not run daqmx driver for pcmcia 6062e daq card

i use labview 8.0 on window xp .when i installed a PCMCIA daq card 6062E, i could not run daqmx driver.It is fine to see that the traditional version is working well.When i install daq card sometimes it is working well with traditional driver but mostly i see error on reading an analog input from PCMCIA daq device.An error called 'base adress' occures .I use last version of driver that is daqmx 8.0.1. and i have installed this correctly but again i could not see any signal on the test panel for daq-mx driver.I don't know what is the problem.Also when i install PCMCIA daq card Please reply this message.I need your helps.
Thanks

Hello,
Thanks for your reply.I will try to answer your questions.
I have checked the Device Mananger and I have seen that the device is detected by Windows XP. For another question the card shows up under both NI-DAQmx Devices and Traditional NI-DAQ (Legacy) Devices consistently in the Measurement & Automation Explorer.I use a way that I reset the driver for traditional NI-DAQ in MAX,and then i reset the device for NI-DAQmx driver in MAX and again i tried to run the test panel of DAQmx driver but again i saw a wrong signal or noise signal on the test panel i could not see the sinusoidal signal that i connected. i do get the test panels to run with the card using the DAQmx driver, But could not run the DAQ diagnostic utility.The error was as i specified below.
03.05.2006 09:49:35
Results saved to: C:\Documents and Settings\serkan\Desktop\Diagnostic Results.txt
Selected Device: Dev1
Device Type: DAQCard-6062E
Serial Number: 107509E
Device Support: (PASS)
NI-DAQmx Version: 8.0 (PASS)
Device Reset: (FAIL)
Error -50002 occurred at an unidentified location
Possible reason(s):
The specified device is not a valid device. The operation could not be completed as specified.
------ DIAGNOSTIC UTILITY ABORTED -----
And for your last question i can say that i have used the DAQ card on other laptops.But the results were the same.İ hope to see your reply
Thanks,
Serkan Buhan
Electrical-Elecronics Engineer
Researcher
TUBITAK-BILTEN

VirtuelPC driver for NI-CAN PCI Cards?

Hi
I could be great if there where a NI-CAN PCI driver usable in a VirtuelPC. We do use VirtuelPC's i our company (ex. in the test area), and the abillity to share a NI-CAN PCI card from the host machine with the virtual PC could be a great feature.
Is there any posibility that this feature will be released in the future?
/Thomas

Hi Thomas,
National Instruments' LabVIEW is supported by Virtual PC. This means that a customer will be able to access his LabVIEW files on the Windows partition on his Macintosh machine. However, we still do not have DAQ driver support or NI-CAN support for Virtual PC.
You are wellcome to make this suggestion at our product suggestion center: http://digital.ni.com/applications/psc.nsf/default?openform
Thanks!
Dennis Morini
Field Sales Engineer
National Instruments Denmark
http://www.ni.com/ask

Need new driver for nVIDIA 7900GTX graphic card (OS : Mac OS X 10.4)

Any one know where i can get the new driver for nVIDIA 7900GTX graphic card (OS : Mac OS X 10.4)

http://www.nvidia.com/object/7seriestechspecs.html
Pls visit above nVIDIA web page.
based on NVIDIA web pages, 7900GTX supports MAC OS X.
but .....seems not so far.

How can I communicate with my PCMCIA-CAN/2 card using Java?

I need to write a Java program to send messages via CAN. The program I used with the Win NT driver of the PCMCIA-CAN/2 card worked. But I have to use Win 2000 now and the new driver nican V 1.6 doesn't work (can't send messages via CAN from my Java program). Thanks in anticipation.

Do you get any error code/message back? Sounds like the Java wrappers that you made for the C dll's need to be recompiled? If the application runs in a weird way using the bus monitor.exe (\NI-CAN) would help.

PCMCIA E series card Voltage Range

In one of our application we want to use E-series daq card for a single channel analog input.
Voltage range is from 0.01 mv to 2 V.
Please let me know could I measure voltage of this range and how?
Please let me know what minimum voltage we can measure using PCMCIA E series card.

Vishal,
The range on our current PCMCIA E Series boards is +/-10V. There are multiple example programs to measure analog voltages for common programming environments that will work with our PCMCIA boards. Hope this helps. Have a great day!

PCMCIA-CAN Series 2 hanging

Hello,
We are using a PCMCIA-CAN series 2 board on two of our machines to get/send PDO data to CANOpen network of 6 nodes.
Built in 2007, Labview 2010 application (using CANOpen library 1.1.3 in combination with NI-CAN version 2.7.4) seemed to work OK mainly because we used it on short period of time (under 12h). To run more longer tests, we run now the machine over 24h continuously and this revealed a small bug. We investigated the case first with NI-SPY. It reported a communication lost problem with the board firmware and propose different solutions or checks (windows interrupts, application code, etc...).
In our application, we have two loops to send and get PDOs on the network. We use function "Wait for PDO" to wait for a TPDO during a time slot and if not received we switch to wait for another one and so on. The other loop takes care of the RPDOs the same way. We have no more than 14 RPDOs or TPDOs for our network. We checked the code and even slow down the switching but bug is still appearing.
We then run the application with other faster computer and made all software updates. Now, NI-TRACE reports (attached with this post) other errors but symptoms are still the same. Application is not able to communicate with board to get/send the PDOs values (or send/recaive SDOs) even the nodes on the CAN network are running OK. It seems that firmware implemented on board stopped functionning or hanged.
We contacted NI sales representative in order to get version 1.1.4 of the CANOpen library (support for LV 2010) but did not get any proposal at this time. We suppose that there is no firmware update as the product is now obsolete. Of course, recommandation was also to switch to new NI PCI board with new library for industrial communications but which is unforunately a little too large to be installed in our panel PC. Another manufacturer hardware will fit for sure...
Reading back my posts in 2007-2008, I remembered also that the PCMCIA boards had more limitations than others PCI boards for example. But, before changing hardware and rewriting the code, I want to give these boards (and all the work done in the past) a last chance.
Does one of you have suggestions or solutions for me ?
Thanks in advance.
Attachments:
20130329SMTSpyCapture.nitrace ‏304 KB
nicanErr.txt ‏5 KB

Hello,
Please find below two snapshots of the code and in particular the TPDO and RPDO loops I have in my main vi.
The TPDO loop receives an array of clusters containing each with TPDO elements declared. Array contains 7 elements actually. TPDO time refresh time has been set to 200ms so that loop switches on a waiting time for each TPDO around 28ms. CAN network speed is 1Mbits/s and the 6 CAN nodes has been setup to send their TPDOs every 20 or 30ms. Only the one used are sent.
The vi "Get TPDO data" is implementing the TPDO wait function. If a new TPDO is available, its value is compared with the stored one (in array element). If new, the TPDO cluster is updated and put in a queue. Then, in this Producer/Consumer queue principle, the second loop dispatches the values in the variables.
The RPDO loop is based on same principle except that the 2 RPDOs are set every 50 ms. The application then uses SDO to send other commands to the nodes.
When our problem appears, we notice that values are not refreshed anymore on the front panel, even commands with SDO are no more possible. Spying the CAN network shows normal activity of the nodes.
First error message we got from NI-SPY was :
“Overflow in the lower level read queue of the CAN card (frames lost). NI-CAN reads this queue at Windows interrupt-time. Solutions: Avoid tasks that generate excessive interrupts on your PC (mouse, ethernet, ...); Avoid running other
applications during your test (screen savers, MAX, ...); use Series 2 Filter Mode to filter incoming traffic; For CAN Objects (Frame API), increase read queue length or call Read more frequently”
So we checked our configuration and computer (scren saver, network connection, etc...). We also ran the application with another one, made updates... Now NI-TRACE reports the information contained in the files attached to my last post. Hard to find the bug if it occurs only after several hours of running time...
With these information, any suggestions or comments ?
Thanks.
Attachments:
TPDO Loop.PNG ‏100 KB
RPDO Loop.PNG ‏68 KB

Device Driver for Quick Can

I want to use quick CAN for the project using LabVIEW .So I need the device driver for Quick CAN so that ,I can interface with LabVIEW.Is there a Driver for Quick CAN for LabVIEW ?
Some Detail on Quick CAN
http://qprotos.com/quickcan.htm

Wow that looks like a piece of junk. You get what you pay for, and that goes for driver support as well. If you bought a NI CAN device or XNET you'd have all kinds of support from this forum trying to help you out. Heck even a Vector device has some love on this forum. And Intrepid has drivers for their hardware in LabVIEW...it needs some attention but it exists.
I say read the documentation, write a set of VIs to talk to the device, and post here if you have any general questions about writing drivers.
Unofficial Forum Rules and Guidelines - Hooovahh - LabVIEW Overlord
If 10 out of 10 experts in any field say something is bad, you should probably take their opinion seriously.

How to get the Windows Vista Driver for ATI Radeon 7500 card?

How to get the Windows Vista Driver for ATI Radeon 7500 card?
I am using a IBM Thinkpad T42 with a 32Mb ATI Radeon 7500 graphic card AGP.
Is there any Vista 32-bit driver to update my card so that this system support Aero effect?
Thank you.
regards,
W. Thong

wthong wrote:
How to get the Windows Vista Driver for ATI Radeon 7500 card?
The Radeon 9000 driver works for the Radeon 7500 card. I have successfully used it on a T43 with Vista Ultimate x86
wthong wrote:
Is there any Vista 32-bit driver to update my card so that this system support Aero effect?
Unfortunately no. The Radeon 9000 driver should bring your graphics score up to close to 2, but it will not get it high enough to enable Aero support.
Cheers,
Bill
I don't work for Lenovo

HT1338 is there a driver for Lexmark X1100 Series All-in-one?

Is there a driver for Lexmark X1100 Series All-in-One ?

Hi,
Might try this...
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-53118-1 &lc=en&cc=us&dlc=en&product=1146331&os=219&lang=en

Install of PCMCIA CAN Series 2 Card

When I boot up my computer with my NI PCMCIA-CAN/2 Series 2 card, it locks up in mid-boot. If I try to put the card in when windows (XP) is running, it freezes. I had this problem at first, and then it disappeared for a short time, but is back again. I essentially had to re-boot my computer several times before it recognized the card, but this trick has stoped working. I have installed the latest NI CAN software (verson 2.3) and still am having the problem. The card is new. I recieved it in march, but only just pulled it out about a month ago, and have only had a few days since then to try and work with it. What could I try to fix this?

Hi James,
That sounds like as if you got a bad card. Your card is still under
warranty. Please contact your local National Instruments branch office to get the board
checked/repaired and give them the same description of the problem.
-B2k

No driver for Airport Exteme WLAN card working in Windows Vista (32bit)

Hello,
Fairly recently I had an Airport Extreme card installed into my Mac Pro. Of course everything works on the Mac side and the card appears with the following info:
Wireless Card Type: AirPort Extreme (0x14E4, 0x8E)
Wireless Card Locale: USA
Wireless Card Firmware Version: Broadcom BCM43xx 1.0 (5.10.38.35)
Current Wireless Network: XXX
Wireless Channel: 1
Under Windows Vista Ultimate (32bit) the card comes up with the following hardware ids:
PCI\VEN14E4&DEV_432B&SUBSYS_008E106B&REV01
PCI\VEN14E4&DEV_432B&SUBSYS008E106B
PCI\VEN14E4&DEV_432B&CC028000
PCI\VEN14E4&DEV_432B&CC0280
The Leopard DVD does not seem to contain any compatible drivers for Windows using Bootcamp for this card. I am really struggling to find a driver that works. The card is listed as 43XX in OS X, and by the Windows hardware ids it seems to be a 432B? I've tried third party drivers for this Broadcom chipset range and nothing will work and even detect a compatible card installed.
Surely there is a working Windows Vista driver for this Broadcom chipset? Does anyone have any suggestions?
Thanks!

thanks for replying..... I'm using the latest driver from the site X.0004 for the x-fi xtremegamer fatality pro. The Sound card is detected just fine. The card shows up correctly, but its just that there are no sound coming out from any of the line out. If I play an mp3 or a movie, I can see that the bar is moving under "Sound" in control panel. I've tested it using headphones etc. The card itself is fine because I tested it on windows xp, well the store where I bought it from did. So its not a hardware problem.

Driver for 3csoho100b-tx LAN card

I searching desperately for a driver for my 3com 3csoho100b-tx LAN card, I have searched Google and several forums but there doesn�t seem to be one available. I know on Linux I can use the tulip driver is there anything similar on Solaris 10??

What happens when you type "ifconfig -a" (while logged in as root to your solaris installation)?
Linux driver won't work.

Looking for LabView driver for Watlow 96 Series Temp. Controller.

In need of LabView driver to control a Watlow 96 Series Temperature Controller. The controller has a RS232 output, so I'm preferably looking for a serial port driver. Thanks in advance.

Nevermind....I found some very useful information in Brian Vibert's postings. Do a search for Watlow 96 Series.

Driver for Linksys Wireless-N CArd

Hi
We need drivers for A Linksys card for the G5 , The card is WMP300N...HELP?????
We can't find anything...
Any help is greatly appreciated
Liz

Hi Steve Webster-
There aren't any Mac drivers as that card is for a Windows machine.
Luck-
-DaddyPaycheck

Driver for PCMCIA-CAN series 2 card needed

Similar Messages

Maybe you are looking for