Driver install don't detect Labview 2013

Hello,
After installing Labview 2013 (32bits) , installing driver (Daqmx,etc...) (DVD feb.2013) , application driver don't detect labview 2013, and doesn't want install anything.
Do you know this problem ? and how can i fix ?
Thanks.
Ludovic
Windows 7 32bits
Labview 2013 Eng 32bits
Devices drivers DVD4 feb.13 (also try with Aug12 version)

Hello,
Thanks for answer,
I can't find link for download devices drivers August2013... Exist ?
(@Julien..) Your download link is Labview 2013 download application, but don't contain drivers (i.e. DaqMx)
In other link for download Labview (2013), ( https://lumen.ni.com/nicif/confirmation.xhtml ) recommended download devices drivers is August 2012 ... (http://joule.ni.com/nidu/cds/view/p/id/3145)
Best regards
Ludovic

Similar Messages

64-bit Labview 2013 Ni-845x = ?????

Rediculous....
If I have the following setup:
- Windows 7 64-bit
- Labview 2013 64-bit
- NI USB-8452
What driver do I use???????
v2.1.2 is 32-bit only...
v2.1 coverd 64-bits but not for Labview 2013, stops at 2012. Found this in a random compatibility chart no where near the damn driver or HW pages.
This is a maze of information, and digging for info like this should not be the norm.
My NI USB-8452 is glitchy when looking for it in NI Max. When I try to use the driver for I2C setup and immediately disconnects from USB (I hear the Window USB disconnect noise).
Has anyone had this problem? What driver do I use for Labview 2013 64-bit for the NI USB-8452.

My box is still not working.
I have:
NI USB-8451 (works fine)
NI USB-8452 (fails on ARG1 and I know it is right).
How can the same piece of cod work for one and not the other. It work previously, and now all of the sudden it's broken for the 8452 only.
See attached picture.
Please help me before I go insane.
Attachments:
WTF.png ‏19 KB

I cannot see the NI-DAQmx icon in measurement window in Labview 2013 (student Edition)

Hi All:
I have installed NI-DAQmx and Labview 2013 (Student Edition). I have connected an NI USB-6008 DAQ and tested it using NI-DAQmx and it is working properly.
Now I tried to do logging of data from this device using the installed Labview software but as I open a new project and go to Block Diagram screen and display the measurement menu I cannot see the NI-DAQmx icon in the measurement window (Menu) within Labview 2013 (student Edition).
Any suggestion?
I am attaching two screen shots.
Please help.
Thanks
Solved!
Go to Solution.
Attachments:
1.png ‏77 KB
2.png ‏88 KB

In which order did you install the software packages?
You should install LabVIEW first, followed by DeviceDrivers!
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Installing Windows 7 on Late 2013 iMac w/ Fusion Drive

Sorry in advance for the long post, but I have tried to exhaust all possibilities, and bring as much knowledge about our environment to the table to avoid confusion.
Here's our goal: Install Mac & Windows on a Late 2013 iMac with a 1TB Fusion Drive
Install our Mac Image with Deepfreeze on Partition 1
Install our Windows 7 x64 Image with DeepFreeze on Partition 2
Here's why our goal cannot work out of the box:
Deepfreeze for Mac, is not supported on a Fusion Drive. Now before anyone says "just don't use deepfreeze"...we are using it, and that is that.
In order to get our existing image to work on the iMac, we had to split the Fusion Drive.
Splitting Up the Fusion Drive
We booted into Recovery, Opened up terminal, retrieved the LvGUID, deleted it, and split up the SSD from the HD.
So now, we have a 128GB SSD, and 1TB HD showing up under Diskutilitiy.
We then partitioned the 1TB HD, into two, 500GB Partitions. One for Mac OSX 10.9.4, and the other for Windows.
The 128GB SSD is going to be used for scratch space, temp, etc. And is irrelevant at this time.
Deploying our Mac Image
After splitting the Fusion Drive, we netbooted and installed a "NetRestore" of our image. Worked completely fine, no issues. DeepFreeze Works fine, the 128GB SSD shows up just fine, and the other 500GB Windows Partition shows up fine. All drives / partitions can be written to with no problem.
Deploying our Windows Image
Deployed our Windows Partition image as we have done in the past, by booting into a windows PE Disk. (We have other various 2009, 2010, and 2011 iMacs across campus, with NO FUSION DRIVES installed, and dual boot them successfully using the same procedure. Minus the splitting of the fusion drive part of course) After the Windows image is deployed to the windows partition, we then boot it up to a Windows 7 Install disk to fix the MBR, Bootrec, and BCD options to allow it to boot properly. Here's where we run into issues: Upon getting the Windows 7 Install screen, the USB Keyboard and Mouse, DO NOT WORK.
Here's the options we've tried to get them to work properly
1. Tried another known working Mac USB Keyboard & Mouse = Failed
2. Tried a known working Windows Keyboard & Mouse = Failed
3. Plugged Just a known working Mac Keyboard into each USB Port to see if recognized = Failed
4. Plugged Just a known working Windows Keyboard into each USB Port to see if recognized = Failed
5. Plugged Just a known working Mac Mouse into each USB Port to see if recognized = Failed
6. Plugged Just a known working Windows Mouse into each USB Port to see if recognized = Failed
7. A Windows 8.1 Recovery USB will boot and the USB Mouse & Keyboard are recognized and installed! (YAY!!) However, we cannot repair a Windows 7 install with Windows 8.1..
BootCamp Drivers & Support Media
Downloaded the Current BootCamp Support drivers to enable the USB and other various drivers to be loaded during setup (Placed the $WinPEDriver$ and AutoUnattend.xml, and BootCamp folder on the Root of a USB, and modified a Windows7 Installation disk and placed on the root as well) The drivers do not load. Have also placed on a brand new USB2, and USB3 flash drive formatted at FAT32, to see if that made a difference, which it did not. The BootCamp USB made within Mac, it loads saying "Now booting into Boot Camp Assistant Created USB Drive..." or something like that (Don't remember the exact Message)
Side Note:
Restored Fusion Drive to its original State, and booted from the BootCamp USB drive, still no usb Mouse & Keyboard Support.

I have same issue
Tried everything differend hdd,ssd as well
Basically when trying instal win 7 via iOS maverick when reboting and windows booting to the first scree everything freezing cant do much.
Also tried install clear ssd without any system, but soon after format ssd or hdd I have error that I cant use this disk to install windows!!!!!!!!!!!!!!!!!
What is funny Windows 8 installing without any problem!!!
what is going on APPLE??wher is support
This issue I have only on Late 2013 on my other Late 2012 this issue not exist and everything working as should.

NI-USRP 14.0 driver ,and labview 2013 64 bit

Hi
Is it possible to use the NI-USRP 14.0 (64 bit driver) with Labview 2013 64 bit ?
have someone tried to install NI-USRP 14.0 drivers and then convert the driver ("instr.lib \niUSRP" directory) back to 2013 version ?
or do i need to purchase the 2014 version if i want to run 64 bit labview & USRP?
Thanks

Hi again
i installed the 32 bit verision of niusrp 14.0 driver (selected to install the driver for labview 2013 ,32 bit version)
& copied the installed files from 32 bit labview directories to the 64 bit version directories
, when opening a usrp vi (like "open rx session.vi" ) it says :
"error loading "niusrp.dll" A dynamic link library (DLL) initalization routine failed.
if i then try to point to another niusrp.dll like the one placed at C:\windows\SysWOW64\ , i got :
" the library selected is not valid for the current platform. for example ,you are running 64 bit labview and the library might be a 32 bit library"
where can i find the "right" niusrp.dll ?
so it seems that the niusrp 14.0 driver does not support labview 2013 64 bit version, ?

Usrp driver 1.3 do not support for Labview 2013 64 bit ??

Hello, dear all
Is anyone install the latest USRP driver 1.3 for LV 2013 64 bit ? I found there is no version for 64 bit LV 2013.

Currently the 1.3 driver supports only LabVIEW 2013 32 bit (even on 64 bit computers.)
The LabVIEW 2014 version will support 64 bit and will be available to download very soon.
Please check here within the next week or so: http://search.ni.com/nisearch/app/main/p/bot/no/ap/tech/lang/en/pg/1/sn/ssnav:drv/q/usrp/

I have an Epson printer on a Wifi network. Windows 7 desktop and and HP Win 7 laptop (my wifes) print to it just fine. My MacBook Pro running Yosemite won't detect it, and I have the latest driver installed. No problem when I had a Canon...

I have an Epson printer on a Wifi network. Windows 7 desktop is running the network, and my wife's HP Win 7 laptop prints to it just fine. My MacBook Pro running Yosemite won't detect it, and I do have the latest driver installed. I didn't have a problem when I had a Canon Pixma on the network, but when I replaced it with the Epson nothing seems to work. I go to add a printer to the queue and only the FAX function of the printer shows up - not the WS-4530 print function. Does anyone out there have any suggestions? Please??? :-)

Hi Kelly,
As someone who has to print from my Mac to a networked printer at home all the time, I can certainly understand how frustrating it must be to have that fail to perform as expected. Let's see if we can get you up and running.
I would suggest that you troubleshoot using the steps in this article -
OS X Yosemite: Printing troubleshooting
Start with the section titled Check the network.
Thanks for using Apple Support Communities.
Sincerely,
Brett L

I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you plea

I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you please advise?

You may need many other updates to retain compatibility with Lion. I suggest you reinstall Snow Leopard. Unfortunately, you will need to erase the drive first. Be sure to backup your data if you haven't done so already.
Clean Install of Snow Leopard
Be sure to make a backup first because the following procedure will erase
the drive and everything on it.
     1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
         with your computer. Insert the disc into the optical drive and restart the computer.
         After the chime press and hold down the "C" key. Release the key when you see
         a small spinning gear appear below the dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, click on Options button
         and select GUID, click on OK, then set the format type to MacOS Extended
         (Journaled, if supported), then click on the Apply button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. After you finish Setup Assistant will complete the installation after which
         you will be running a fresh install of OS X. You can now begin the update process
         by opening Software Update and installing all recommended updates to bring your
         installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

*SOLVED* Device not detected/ No driver installed for X-FI Fatal

OK!!!! the only reason I signed up here was to post that I have (for me) solved my problem.
Before I get into details this occurred on a fresh system with latest drivers for hardware used.
The problem was installing my X-Fi card on my 680i m/b (striker extreme).. when I would install the driver it would simply crash the computer and when it started up the hardware was not detected to used the software and the device manager said no driver installed.. I tried everything.. I installed the driver in safe mode (yay it worked without crashing) then I booted for windows only to have it blue screen for a second and restart... repeating the cycle.. so i reinstalled windows again... I tried installing the driver different ways in windows.. nothing worked... I gave up...
BUT!!!
today while i was at work I decided I would try one last thing.
this is what got it going. I have SLI 8800ultras that covered the PCI slot on the bottom of my board and I though I would try the card in this slot to see if it worked there... so I disabled SLI took out my bottom card put in the sound card in the bottom slot, installed the driver... It installed 00% no crash... even better it worked after the restart!!!... so then I had to test if it worked in the top slot so I powered down, moved it up to my top PCI slot and windows auto set the driver for it (as it was already installed) It worked in the top slot now... Finally I put in the second 8800 to make sure it worked with this slot in use... It still worked fine with SLI enabled. because I was unhappy with the mess I made installing drivers all the time as I did with the many crashes I decided to do a fresh install of windows making this card work from the start so here is what you need to do if you have a 680i board with SLI. this is exactly what i did with my fresh install.
install only one GPU card..
Put the X-FI in a different slot that isn't giving you problems
Install windows
Install service pack 2
install your chipset drivers
install sound card drivers
power down, change sound card to permanent slot
test - power down
put in the second GPU card
install GPU drivers
Good luck you all having this problem.. I hope my solution helps you.
Bryan

I think I?got a similar?problem earlier today when I was messing around with?onboard audio?that I later removed and after unplugging a?USB headset.
Have you checked the device manager, is there any higlighted hardware that has a exclamation mark next to it.
I fixed the issue by simply uninstalling the WDM device with the exclamation mark and restarted.

Is it possible to install a ssd in my 2013 imac 27 inch that currently has a serial ATA drive?

Is it possible to install a SSD in my 2013 imac 27 inch that currently has a serial ATA drive?

Not only possible, but well documented as well:
http://www.everymac.com/systems/apple/imac/imac-aluminum-tapered-edge-faq/how-to -upgrade-imac-hard-drive-aluminum-2012-2013.html

How can I build a LabView application that uses the 2012 runtime, on a development system with LabView 2013 or 2014 installed?

I need to build a LabView application .exe to run with the 2012 Runtime, for legacy support. I currently have LabView 2013 installed on my development system, and have 2014 available. How can I build an application that uses the 2012 runtime on this development system? Do I have to downgrade to 2012? Thank you.

We have existing customers that have installed our application that was originally built with 2012 (provided by a contractor that is no longer available). Due to IT regulations, it is far easier to update these customers by simply replacing the .exe file, than creating an install that their IT department must run.
If I have to downgrade to LabView 2012, where can I get the installation for this?

Update tries to install on drive I don't have. What do I do?

Update tries to install on drive I don't have. What do I do?

Brucebre,
I am very sorry, but full versions of the ZoomBrowser program and other software originally packaged with your camera are not available for download. In order to install the software, you will need the original Solutions Disc and a CD/DVD-ROM drive.
If this is a time sensitive-matter, additional support options are available at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

After installing "Java for OS X 2013-004" update, Java apps don't work anymore as expected

After installing "Java for OS X 2013-004" update, Java apps don't work anymore as expected.
Windows of Swing apps don't display all GUI elements.
After replacing System/Library/Java from a Time MAchine Backup, everything works normal again.
Is this update corrupted?

"avoid using Java in a web browser at all,..."
Good advice.
"...old Java apps/applets that aren't written to modern specs ..."
The stand-alone Java Swing applications, that don't display their GUI elements after installing this update, have been written according to modern standards. With Oracle Java7, and with Java6 from Apple prior to this update, they run absolutely flawlessly.
This is absolutely Apple's fault.

Compatibilidad de driver 845 para daq 8451 para labview 2013

Estoy intentando instalar el driver 845 para poder emplear la daq 8451 para un proyecto pero se diseño empleando labview 2011 y actualmente tengo el 2013, al momento de intentar instalar el driver más nuevo me aparece un error debido a que tengo un software más reciente y no se intala generando que al momento de querrer utilizar el proyecto busca el driver para actualizarlo y no llego a nada.
No se si alguien conosc la forma de poder instalar el driver para labview 2013.

Hola Artama,
Gracias por utilizar los foros de National Instruments! Que versión del driver 845x estabas instalando? Que error es el que te aparece al tratar de instalar? Te envío la liga de la última versión del driver (2.1.2 agosto 2013):
http://www.ni.com/download/ni-845x-2.1.2/4141/en/
Podrías descargarlo e intentar nuevamente con esta versión? En caso de que te siga apareciendo el error te agradecería si pudieras adjuntarlo en tu respuesta.
Saludos!

Install LabVIEW 2013 on Scientific Linux 6.4

Has anyone successfully installed on SL6.4? I install and no response - try to start using icon but no errors or slash screens. Did put the 32 libc2 on the machine. It asked for kernel sources, but for 64 bit?. What is correct?
Thanks,

Zander,
I have not installed LabVIEW 2013 on Scientific Linux 6.4 before, but I will see if I can help you out. First did you install LabVIEW 2013 32 bit or 64 bit? Second does just the LabVIEW shortcut on the desktop not work (icon) or can you just not load LabVIEW at all?
Thanks

Driver install don't detect Labview 2013

Similar Messages

Maybe you are looking for