Driver Installation Error, help need

Hi all,
I just downloaded the newest drivers for my Soundblaster Audigy ZS 2, WinVista 32 bit.
When I try to install, everything goes fine till an error occured (see screen)
Screen: http://img5.imageshack.us/img5/660/errordj0.jpg
Something with the APOIM installer, any help would greatly be appreciated. I already searched the FAQ and known issues etc.
Thx in advance, xGj.

Hey I had that same error but?I resolved it.. First download winrar, www.rarlabs.com, second install it and then right click that exe for your driver and click on extract all to that specific folder, for vista the default is downloads, and then just extract and run the setup.exe in that folder and not from the program that you have downloaded from the creative driver website. Worked for me it should work for ya also, Good Luck...

Similar Messages

32bit DIFx Driver Installer Error when Installing 9.0.2

Never had a previous problem with iTunes and when I went to use it this morning, it crashes everytime. Uninstalled completely, reinstalled 9.0.2 and now I get an error "32bit DIFx Driver Installer" and iTunes "finishs" installing and crashes after opening again. Have tried unsuccessfully to figure out a fix for this. All my children got iPod Touches for Christmas and I got a brand new iPod nano and none of us can use them now. Please help!

Hey guys! So, I experienced the same issues with the newest iTunes update. I updated several days ago, but I used iTunes for the first time since the update today. iTunes would load but immediately display a message that it needed to close. After several attempts to open iTunes, I reinstalled QuickTime as suggested by another website. Also suggested was trying to repair QuickTime and iTunes. When that didn't work, I removed both QuickTime and iTunes and did a clean reinstall from new downloads. When I did this, I got the 32bit DIFx Driver Installer error. It "finished" the install, but it still closed immediately upon opening. I ran Malware-Bytes and Hijack This to check for spyware/adware/mal-ware a few days ago so I was fairly certain my system was clean...but after two hours of trying to figure out this problem, I decided to go ahead and check for virus or malware.
Indeed, I found six files (mostly located in the System Volume Information folder). After having Avast remove these files...iTunes successfully installed without the DIFx error! So much for being "sure" my system was clean. The files found were all related to the Win32:Malware-gen virus.
So I suggest you check your system for malware and virus infection. I did my scan in safe mode and did the most in-depth search that Avast will perform. I highly suggest doing a full search with UPDATED virus program even if you think your computer is okay.
I have had no issues with iTunes after cleaning my computer!

Envy 5640 - Windows Vista Driver Installation Error - Please Help

Hi
Having problems installing the supplied (and downloaded) driver for our new HP Envy 5640 on my daughters Sony Vaio running Vista.
The printer is up and running and working perfectly on our iOS and OSX Mac devices.
The PC can see and communicate with the Printer.
But when I go to install the supplied (and the downloaded) driver/software it comes up with the following error:
<<
Install Failed
The software required for your printer could not be installed.
For more information click the Details button below.
DETAILS...
The unsuccessfull instalation will be cleaned up, and then you will be guided through searching for and applying a solution to this issue.
>>
Then when DETAILS... button pressed:
<<
Installation Error
Key not valid for use is specified state.
>>
I haven't entered a key, nor a state? I'm in the UK.
Any ideas?
Thanks in advance
Dave

Hello there! Welcome to the forums @Stodgy70
I understand you're facing troubles when installing your Envy 5640 on a Windows Vista system.
After researching the error you're receiving, I would suggest creating a new User Account on the computer and ensuring it has Administrator Privileges, and trying the installation again from there.
Here is the direct link for you to download and install the printer on Windows Vista:
HP ENVY 5640 e-All-in-One Printer series Full Feature Software and Drivers
Please let me know the results, have a great weekend
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

"An unknown installation error occurred" need help!!!

hey guys so i just recently restored my whole MBP. I ran the original disc, went into Disk Utilities, erased my HDD, installed OSX (10.6.8) and then ran the software updater. Everything is up to date. My only problem is that when i run the disc that came with all the bundled applications, it gives me this error "An unknown installation error occurred." I don't know whats going on and could use some help!
Much is appreciated!!

OK I have the scenario:
Thinkpad printing fine in den, not docked, using a wired / cable network connect etc..
1) Suspend machine, walk into office
2) Cold dock it with docking station with machine suspended
3) Unsuspend machine
4) Surf, need to print an invoice
5) Attempt to Print to normal network printer --> no
Attempted to print to Snagit virtual printer --> no
Attempted to print to Quicken vPrinter --> no
Attempted to print to 2nd network printer --> no
6) Can I open any defined Printer Properties pages in FF or TB --> no
7) "An error occurred while printing..." from FF 27.0.1
8) From TB 24.0, no error message, the print dialog opens and when I select print, the dialog box disappears like it's going to print and then no printouts.. and I do not get "An error occurred while printing.."
8) Time to reboot..
Something is not getting reinitialized properly. I keep all my stuff current and ever since version FF 27.0 and TB 24.x no dice. Im current at FF 27.0.1 and TB 24.3.0. Thanks.

Labview 2009 SP1 Installer build help needed

Hello,
First time posting here. I have a rather large project that I recently converted from Labview 7.0 to 9.0. I am able to build an executable and it starts up Ok but I don't know for sure if it works. Since I couldn't build an installer, I copied the folder containing the .exe onto the targeted machine and installed Labview Run-time Engine 2009 SP1. The executable then complains that it needs the full development version to work. I am not too worry about this part at the moment, but if you have any pointers, please go ahead and post them.
Ok, I have gone through a lot of posts on building and installer but it seems the one post that has something similar to what I experienced didn't get an answer. Here's the Build Errors from the pop-up dialog:
CDK_Item_OnDoProperties.vi.ProxyCaller >> CDK_Item_OnDoProperties.vi >> CDK_InstallerConfiguration_Editor.vi >> CDK_Build_Invoke.vi >> CDK_Engine_Main.vi >> CDK_Engine_BuildDevPart.vi >> NI_MDF.lvlib:MDFBuildDevPart_SetOtherProperties.vi
Loading product deployment information
Loading product deployment information
Loading product deployment information
Loading product deployment information
Adding files to installer
*** Error: An internal tool or library returned an error. (Error code -21)
*** End Error Report
*** Error: Windows SDK function returned an error. (Error code -12)
*** End Error Report
The build log file has slightly more info:
    [LOG ON] Mon May 31 20:55:07 2010
<<<MDFConfig_SetDeveloperLanguage>>> Language id: 9
<<<MDFConfig_SetDistributionLanguage>>> Language id: 9
<<<MDFConfig_SetBuildDir>>> Build directory: C:\HardwareTest\XXX\Release\Installers\Lab Test Suite 4.2.9 Installer - XXX
<<<MDFConfig_SetBuildMode>>> Build mode: 1
    [NMDK BEGIN] Mon May 31 20:55:07 2010
     Building developer part
> Adding files to installer
<<<MDFBuildDevPart_SetFileNames>>>
<<<MDFBuildDevPart_SetDefaultInstallDir>>>
<<<MDFBuildDevPart_SetUpgradeInfo>>>
<<<MDFBuildDevPart_SetOtherProperties>>>
>
> **************
> *** Error: An internal tool or library returned an error. (Error code -21)
Error in MDF API function: _MDFBuildDevPart_SetOtherProperties
nmdkSetInformationalProperties returned error code 26024
> *** End Error Report
> **************
>
Adding product dependencies to developer part
>
> **************
> *** Error: Windows SDK function returned an error. (Error code -12)
Closing dist kit
***** About to begin MAXImportConfig:oMAXPartModifications...
No MAX import files specified - nothing to do - returning.
Error in MDF API function: _MDFBuildDevPart_Close
Error in MDF::BuildDeveloperPart::Close.
ERROR: Caught MSI Exception:
<Unable to format error record.>
MSI error code: 6
> *** End Error Report
> **************
>
    [LOG OFF] Mon May 31 20:55:07 2010
    [MDF END] Mon May 31 20:55:07 2010
     Closing MDF.
I realize that I should post my project file but I can't do that until tomorrow. From those 2 errors, can you tell me what the installer builder is looking for? I have gone through all my dependencies and they look Ok at the moment.
Thanks for you time.

Hi Celeb,
I had to help out on another project and finally only getting back to looking at this issue yesterday. As you suggested, I went ahead and created a new project and created new build specifications (exe and installer). I was able to properly build both items but won't be able to check out the executable til later this week.
I noticed one thing about the project that Labview produced after converting the old *.bld file to a project file.  With the converted project, Labview adds unexpected installer destination folders into WindowsFolder in the Installer/Source Files/Destination View. I thought I deleted them before but they seem to make it back (kinda hazy about this at this point).  My actual installer folder should only go into the WindowsVolume folder. Anyway, on the new build spec, since I don't manually add the installer folder into the WindowsFolder, nothing get populated there and the installer is able to build properly. This might have been the cause of my inability to build an installer with the converted project/build specs.
I hope NI could add in more details into the build error messages. As it is, it's really difficult to know why a build failed because there's no details in those messages.
Thanks again,
T.

"startup drive full" error - help

I have gotten a "startup drive full" error a couple of times while using Microsoft Word. It usually occurs when I am trying to save something. My drives are no where near full. What is causing this? How do I fix it?

One of the reasons (when one exists) for a startup drive full message,
could be if the computer has several temporary files and virtual memory
files on the hard disk drive; this could happen if you have insufficient
installed chip RAM and the computer is using HDD free-space as RAM.
And if you are multi-tasking in Mac OS X, there may be a point where
the drive is fully in-use. The utility "Activity Monitor" could tell you what
is happening in the system at different intervals and perhaps you could
tell what is running in there and using a lot of virtual memory; and also
what that utility says is going on elsewhere at the same time.
You may have to boot the computer from the Installer disc and use
the version of Disk Utility on that (in the Installer's menubar is where
you find options, other than running the installer on that disc) to run
'repair disk.' There also may be some caches and other files on the
drive which are not properly being cleared after quitting applications
or after saving works in progress.
A variety of maintenance tasks can be performed to help the Mac
run better; and maybe these are overdue. I use an easy way out
and do not boot into the single user or other modes to do house-
keeping chores in OS X 10; the software (runs free) I choose to
have do these, on occasion, is called OnyX and is a download
from Titanium Software online. An easy search, to get there and
see the correct download for the OSX version your machine runs.
The OnyX 'automation' selection has several check-boxes and
a few times a year, I run all of the options shown there; otherwise
I only run the default set, and then have the utility automatically
restart itself afterward. There are settings in the OnyX preferences.
Not sure what else may be going on in the computer's hard disk
drive; but to use the boot/install disc's Disk Utility to 'repair disk'
and also to verify or see the status of SMART, may tell you if
the hard disk drive is starting to fail. (Although it could stop work-
ing and not say it was failing; checking anyway, is easy enough.)
If you have a third-party disk utility such as Drive Genius or
maybe DiskWarrior, these may be able to check and repair
some aspects of the hard disk drive's files. Some of these
tools are better at some tasks than others; and so I am not
sure which one(s) are best at specific jobs. Each is a bit
different and so there are times where having more than one
could be very handy... if one knew what they did, and when
to use one over another third-party disk utility. (I don't!)
At some point, it is very handy to have an externally enclosed
FireWire hard disk drive, and be knowledgeable and practiced
in making bootable clones of the computer's hard disk drive
and the contents there in. This can give you great backups
with the ability to clone the complete disk image back as it
was, but on to a repaired or low-level reformatted HDD. I use
a free-running utility to clone, Carbon Copy Cloner.
Hopefully a fix as simple as using the Disk Utility found in
the installer (hold C key on startup with disc in optical drive)
and do not launch the installer, use Disk Utility from menubar;
and 'repair disk' may help. If there is a defect in the Hard Disk
Drive (HDD) a repair may help; or a more invasive approach
may be required, to include other tools in the Disk Utility, which
could totally erase all your stuff plus the OS from that hard drive.
Not sure how much experience you have in any of this; so at
this point...
Good luck & happy computing!

Photoshop installation Error. Need Help! Please.

I downloaded a trial copy of the adobe photoshop cs4, but I was having an error.
"session has dependencies that cannot be satisfied"...
My laptop specs:
Processor: Intel Dual Core 1.7 GHZ
Memory: 2.5 gig
Video card: 256mb Intel GMA 950
HDD: 80gb
Please help me. I really want to try out photoshop before I buy it.

What info is in the Setup log file mentioned in the dialogue box?
Find and read installation logs for Adobe Creative Suite 3 and 4 products
http://kb2.adobe.com/cps/400/kb400593.html

STILL THE SAME: Photoshop installation Error. Need Help! Please.

I downgraded my vista to Windows XP Professional( 5.1, Build 2600) but the same error is showing.. Please advice..
I downloaded a trial copy of the adobe photoshop cs4, but I was having an error.
"session has dependencies that cannot be satisfied"...
My laptop specs:
Processor: Intel Dual Core 1.7 GHZ
Memory: 2.5 gig
Video card: 256mb Intel GMA 950
HDD: 80gb
Please help me. I really want to try out photoshop before I buy it.

As I asked in your other thread on this same issue:
What info is in the Setup log file mentioned in the dialogue box?
Find and read installation logs for Adobe Creative Suite 3 and 4 products
http://kb2.adobe.com/cps/400/kb400593.html
Just follow the link provided above to see where the Setup log file is and what it says. The answers (or the clues to your issue) are in there.

Emu 1616m pcmcia cardbus driver installation errors: this device is not config correctly (code1)

Hi, can anyone help, I use a 1616m pcmcia card bus in my dell inspiron laptop, its been working fine no errors for the last year, then suddenly today, I go to use it and no sound, and my DSP reds out, and it states my hardware or drivers my need re-installing. So I have un-installed all software, drivers etc, Then when I insert the pcmcia card bus in, it reconizes it, found new hardware, I tell it to use the driver disc. This is ok, its installing the software, then I get the blue screen of death, crash!. Iv tried it countless times, clearing the registy etc, but if I dont get the blue screen I get an error that my hardware may not work properly blah blah and this error: e-mu e-dsp audio processor (wdm) this device is not configured correctly (code 1).
Do I have to factory reset my laptop and reload everything, days of fun.
Has my well looked after pcmcia card bus broken, just after the year is up!! the irony
Are there better pcmcia controller drivers than: ricoh r5c475(ii) and would they help this issue
does anyone have any ideas please!!

Upon latest reboot, I also received this error message: "The application failed to initialize properly (0xc0000005). Click OK to terminate the application."
Then I got the iTunesHelper not installed correctly error again.
Then the "Windows can't check for updates" error message.
Then "Apple Push has stopped working." Then a quick DEP error message that disappeared but said something about Apple Push being closed.
I'm also getting denials of service logged by McAffee. Not sure if I'm getting a virus/attack or not.
Not sure if it's a problem with my old desktop machine, my Windows Vista updates, or iTunes, but I'm very frustrated and out of ideas to try.
Thank you for your help!
Tristan

Build installer error, help

Hi all,
There's a problem need your help.
I have a LV8.5 PDS. And I create a exe, when I want to create a installer, I cannot found any information is "additional installer". When I try to build it, error reports as below.
error information:
CDK_Build_Invoke.vi.ProxyCaller >> CDK_Build_Invoke.vi >> CDK_Engine_Main.vi >> CDK_Engine_PreBuild.vi >> CDK_Validate_DistParts.vi >> CDK_DistParts_GetInstalledProducts.vi >> NI_MDF.lvlib:MDFProdInfoList_Open.vi
Before I reinstall my notebook, it worked.
Thanks ahead.

From the forum
The build specification for your installer may have been corrupted. Try the following to correct this:
Open up your project in the Project Explorer window and expand the Build Specifications tree.
Right-click all of the applications (executables) build specifications that are included in your installer and select Build to force each one to rebuild.
If all the executables build successfully, next right-click your installer's build specification and select Properties to change its configuration.
In the Category pane on the left, navigate to the Source Files category.
Find your executable (.exe) files on the right side and click it to select it. Press the Delete key or click the red X at the bottom of the window to remove the executable and its associated files from the build.
Re-add the executable and its files to the same folder by selecting the executable in the Project View pane and the proper folder in the Destination View pane (on Windows systems, this is typically ProgramFilesFolder\[your product name]), and clicking the blue arrow button in the middle of the window.
Repeat steps 5 and 6 for any other executables you have in your installer, as well as for any other files which show up in the ProgramFilesFolder path.
Your installer should now build successfully. If that does not work, try making a new installer build specification which has all of the same settings as the build specification which does not work. If the new installer builds properly, you can keep it and delete the old, corrupted specification.

Tiger installation error - help please

Can anyone give me any advice?
Trying to install Tiger, get through the DVD test and disk verifying, and then get this error message
"There were errors installing the software please try again"
(which of course i have with no luck)
- i've updated firmware
- run disk utilty and cocktail
- removed all peripherals
- Have plenty of harddrive space
I read on the apple support pages this may be a RAM issue. I have 512MB internal RAM which was a replacement for a corrupt card, (done about six months ago and been fine), and 512MB added in the slot. I've removed the 512 in the slot and tried to reinstall Tiger with the same result.
Does anyone have any ideas? Is it possible to turn off the internal RAM and just run off the slot card?
Appreciate any help

Here's a long discussion about the -9972 error. It can be pretty serious, so take the time to explore the solution options that are outlined. If all fails be sure to backup if you can, then erase the drive and reinstall.
The following was contributed by Fumiaki Kawashima.
The error message, "Error: The underlying task reported failure on exit (-9972)" is a serious filesystem error in the Mac OS X Core Foundation. The problem can also lead to other critical errors such as "Keys Out of Order," "Invalid node structure" and/or "Invalid sibling link." The causes and scenarios vary. Troubleshooting a solution may depend upon computer configuration and whether the -9972 error is accompanied by other critical errors. This issue can also lead up to a kernel panic. If the error occurs when an external FireWire device is connected, disconnect it until you verify the device's compatibility.
Symptoms:
In most cases, you are unable to restart from Mac OS X.
* A volume is grayed out or not mounted with or without a kernel panic.
* A folder with a flashing question mark may appear.
* A bad partition map may be reported.
* A target disk mode solution may not work.
* Most likely, Disk Utility, Norton Utilities, TechTool and DiskWarrior cannot fix the issues.
* The high level disk format (Standard format) may unable to perform.
* You may unable to re-initialize the hard drive.
* A disk physically malfunctions in the worst case.
Example of an accompanied error message:
DiskWarrior normally fixes 1 to 6, but cannot fix errors 7 to 10 if the symptoms are very bad. There is no definite case.
01. Volume check failed
02. Invalid B-tree Header
03. Invalid map node
04. Invalid extents entry
05. Invalid clump size
06. Incorrect block count file
07. Invalid node structure
08. Overlapped extent allocation
09. Keys Out of Order
10. Invalid sibling link
Related documents:
What to Do When It Finds an Error
Technical overview of disk volume structures
Possible causes:
* Third-party FireWire device or enclosure, or other peripheral devices.
* Third-party mass storage drives or PCI card issues.
* Incompatible third-party kernel extensions.
* Mac OS X installer disc is improperly treated.
Solutions:
If possible and needed, back up data before troubleshooting. Methods (4) and (5) are for Power Mac desktop computers other than G5 models. The best bet is method (4) if you encounter multiple bad errors.
1. Unplug the power cord. Disconnect all third-party hardware except Apple keyboard and mouse before you start.
2. Do NOT re-install any third-party software/hardware until you completely solve the issue(s) and carefully investigate the compatibility with Mac OS X 10.3.x you install.
3. If another critical error "Invalid sibling link" is detected at any phases, disconnect and reconnect all internal power cords and data cables for hard drives and any ATAPI device. To do so, you may need to read the computer's CIP Instructions in advance. Normally, you do not need to remove third-party RAMs.
Method 1:
(1) Start up from Mac OS X 10.3.x Panther Full Install CD or DVD.
(2) Re-initialize and re-partition the hard drive. RECOMMENDATION: Select "Zero all data" option if "Invalid node structure" or "Keys Out of Order" error is detected.
If this method is of avail, go to Method 2 or greater.
Method 2:
(1) Start up in Mac OS 9.2.2 and shut down the computer.
(2) Start up from a copy of a Disk Warrior bootable CD for Mac OS 9.2.2.
(3) Run DW to fix the damage(s).
Method 3:
(1) Unplug the computer.
(2) Find a second ATA drive and jumper it as MASTER. Jumper the hard drive in question as SLAVE. Verify the jumper pin settings.
(3) Install Mac OS 9.2.x system on the MASTER drive, and update it to Mac OS 9.2.2.
(4) Start up from Mac OS 9.2.2. Re-initialize and re-partition the damaged hard drive with Drive Setup using the "Zero all data" option. Unplug the computer and reconfigure the jumper pin setting on the repaired drive for MASTER and the second drive for SLAVE.
(5) Restart from Mac OS X 10.3 Panther full install CD. Re-initialize and re-partition the repaired drive to install Mac OS X 10.3. Update to Mac OS X 10.3.7 via Software Update. Repair the disk permissions after each Mac OS X 10.3 installation and Mac OS X 10.3.7 update.
You may want to try starting up from Mac OS 9.2.x Full Install CD instead of from (2) to (4).
Method 4:
(1) Find a desktop computer that has an ATA controller PCI card (SCSI environment) and has two hard drive bays. This will make your damaged drive appear as a quasi-SCSI hard drive. Mac OS 9.2.2 must be pre-installed on the computer. I recommend a host computer that installs an Ultra DMA/xxx or xxx (ATA-x) interface equal to or better than the damaged drive with backwards compatible.
(2) Set the host computer's primary drive as MASTER and your damaged hard drive as SLAVE and install the damaged drive in the second drive bay of the host computer. Verify properly configured jumper pin settings in advance.
(3) Start up the host computer from Mac OS 9.2.2. Launch the "Drive Setup" utility. Re-initialize the damaged disk on the second drive using the "Low level format" option. It may take hours but less than "Zero all data" option. Note: Normally, a low level format with a quasi-SCSI drive takes much less (30 - 40%) time than an ATA configuration drive. Note that "Low level format" fixes all difficult logical damage.
(4) Put the fixed disk back in your computer's drive bay. Re-configure the jumper pin setting to MASTER before you place it into the drive bay of your computer.
(5) Restart from Mac OS X 10.3 Panther full install CD. Re-initialize and re-partition it to install Mac OS X 10.3. Update to Mac OS X 10.3.7 via Software Update. Repair the disk permissions after each Mac OS X 10.3 installation and Mac OS X 10.3.7 update.
Note that Panther's Disk Utility does not implement a "Low level format" option.
Method 5:
If Method 4 does not work or fix the damaged drive, let me know. You may need an advanced technique to fix it if the drive is physically not a problem.
OPTION:
Purchase a known good hard drive that conforms to your computer's ATA specification. Fix the damaged hard drive some other time. Nowadays, prices of hard drives are inexpensive.

Oracle forms installation - some help need

I am trying to install Oracle forms - but get the follwing message:
Checking swap space: 576 MB available, 1535 MB required. Failed <<<<
Some requirement checks failed. You must fulfill these requirements before
continuing with the installation,at which time they will be rechecked.
Continue? (y/n) [n]
actually - I have no choice to choose y and try what's going on - so - is this means that I shoul add some 1.5 GB of RAM to my computer? (I have already 700MB, only 300 of them are used)? I am using WinXP, free HD is above 3.5 GB, 2.4GHz processor.
Can I try to find some workaround - e.g. simply try to copy jar's from 'stage' (direcotry in installation disk) in Oracle application server's lib directory (where it is in Oracle_Home directory?)?
Any experience with installing Oracle forms?
This was trying to run setup.exe, but when I am trying to run wsf.exe - I get:
SEVERE: Unable to locate the MDAC Update Status registry key value, probably because the installation was aborted.
MDAC possibly stands for Microsoft Data Access Components? If so - where is problem - I can run a lot of DB servers, including Oracle server itself normally?
BTW - is there any free service available for Oracle Forms skills development (e.g. as for Oracle SQL the Intel test drive is available?)
user454720

OK - now I increased the max limit of my page file and now I achieved this:
Starting Oracle Universal Installer...
Checking installer requirements...
Checking operating system version: must be 5.0, 5.1 or 5.2 . Actual 5.1
Passed
Checking monitor: must be configured to display at least 256 colors . Actual
4294967296 Passed
Checking swap space: must be greater than 1535 MB . Actual 1600MB Passed
Checking Temp space: must be greater than 150 MB . Actual 1942 MB Passed
All installer requirements met.
Preparing to launch Oracle Universal Installer from C:\DOCUME~1\ADMINI~1\LOCALS
~1\Temp\OraInstall2006-03-18_01-57-43PM. Please wait ...
however - after this I receive the standard messgae:
'setup.exe has encountered a problem and need to close. we are sorry for the inconvenience..... Please tell Microsoft about thsi problem'
actually - I have little ideas what to do further - maybe I should look for other Oracle Installer version? I am using:
Oracle Universal Installer version: 10.1.0.2.0
and I am trying to install
Oracle Deveoper Suite: 10.1.2.0.2 (so - a bit higher)
I can run OUI without any problems, my Default JRE is 1.5_1 - so - all seems to be OK?
Please - if any idea - help me :))
Thanks in advance!

How can I get the scrubber software to correct a driver installation error?

I am currently on Windows 8.1. When I try to install the printer driver for my OfficeJet Pro L7650 I get the following error message: "System cannot find file specified".
I have read that there is a scrubber software that will solve this issue. How can I get this software?
This question was solved.
View Solution.

You can get that HP program here.
Restart your computer.
Next run the HP Printer Install Wizard program found here.
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

Using 2 drives in MBP - help needed please.

I have an 2009 Unibody MBP with a 320GB 7200 HDD, that's nearly full.
I want to instal 2 drives in it; one 60GB SSD for my applications and the OS, and one 1TB normal HDD for everything else (by removing the Superdrive). The idea being that the machine boots from the SSD for quick start-ups, while the HDD has all my data on it.
I need:
- 1x fast/quality 60GB 2.5" SSD, with dual drive kit/enclosure thingy.
- 1x 1TB 2.5" HDD. (I believe the only ones available this size currently run at a weird 5200 RPM?)
- 1x easy transfer/set-up method (to get apps/OS onto the SSD separately off my current single drive safely, then my data onto the new HDD).
- 1x Superdrive connection/enclosure for occasional external use of the DVD drive when I need it.
Questions:
(1) Is it best to set-it up as ONE drive partition, or have them as separate partitions?
(2) Will my 1TB Time Capsule be able to back both drives up easily, anything I need to do?
(3) Are there any downsides to doing this (yes, Applecare will not fix due to removing the Superdrive if future probs, but I can live with that)?
(4) Where in the UK can this be stuff be bought from, really need somewhere that offers help setting it up; videos and all.
In the US you have OWC (http://www.macsales.com ) who offer some great options, but I haven't found anywhere online in the UK offering a similar helpful package for the non-tech people. (importing from OWC would add £60+ import taxes I really don't want to pay - shame they don't have a UK operation :-|).
I know there are some cool tech people around here who know about this stuff, so really any other advice/links to help very gratefully received.

jimthing wrote:
(1) Is it best to set-it up as ONE drive partition, or have them as separate partitions?
For most purposes, the SSD and HD should each have only a single partition for normal use.
(Some folks put a copy of a heavy-duty disk repair app on a separate partition; and/or copy their Install disc to one via the Restore tab of Disk Utility; and/or install a different version of OSX on a separate partition.)
Be sure to have at least a minimal Admin account on the SSD.
(2) Will my 1TB Time Capsule be able to back both drives up easily, anything I need to do?
Yes. They should both be backed-up by default.

ORA 12170 : Connection timeout error : Help needed

Hi,
The scenario is as follows: I have Oracle 11g R2 installed on a Windows Server 2008 (32-bit) server. The database SID is 'PGMS'. I am accessing (or want to access remotely) the Oracle database from the Visual Studio 2008 development environment (client environment) running on a Windows XP (SP3) platform. I have already installed the ODAC (Ver. 11.2.0.2.1) package for the Visual Studio environment.
I have created a sample Windows Forms application that uses the Oracle data access components. The sample schema HR in the Oracle database has already been unlocked. This is the schema that I am using in the application.
The issue that I am facing is that when I am adding the data connection in the Visual Studio environment; 'Test Connection' functionality returns the following error: ORA-12170 ... Connection timed out.
I have checked the TNSNAMES.ORA file, and everything is as is mentioned in the Oracle documentation. It is as follows:
PGMS=
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.0.161)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = PGMS)
Kindly request the community to help me out in overcoming the error and in making the connection successfully. We have a System administrator but not a database administrator. The Oracle installation has been done by me.
Thanks,
Renj
----------

Sunny, it's as follows:
(1) SQLNET.ORA file contents are as follows:
# This file is actually generated by netca. But if customers choose to
# install "Software Only", this file wont exist and without the native
# authentication, they will not be able to connect to the database on NT.
SQLNET.AUTHENTICATION_SERVICES = (NTS)
(2) LISTENER.ORA file content are as follows:
# listener.ora Network Configuration File: C:\app\Administrator\product\11.2.0\dbhome_1\network\admin\listener.ora
# Generated by Oracle configuration tools.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = CLRExtProc)
(ORACLE_HOME = C:\app\Administrator\product\11.2.0\dbhome_1)
(PROGRAM = extproc)
(ENVS = "EXTPROC_DLLS=ONLY:C:\app\Administrator\product\11.2.0\dbhome_1\bin\oraclr11.dll")
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.0.161)(PORT = 1521))
ADR_BASE_LISTENER = C:\app\Administrator
Edited by: Renjith2 on May 9, 2011 3:17 PM
Edited by: Renjith2 on May 9, 2011 3:22 PM

Driver Installation Error, help need

Similar Messages

Maybe you are looking for