Driver issue after win 8 downgrade

Hi there
I need some help acquiring the correct drivers for my netbook. I recently down graded to windows 7 - 8 was running slow and doing my head in.
I have the hardware ID. Please help.
Ethernet Controller:
PCI\VEN_10EC&DEV_8136&SUBSYS_21A9103C&REV_07

Hi:
DL and install the second driver (3rd item) on the list at the link below...
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=7&Level=5&Conn=4&DownTy...

Similar Messages

Apple iPod USB Device driver issue on Win XP - syncing shuffle 2nd gen.

Hello fellow iPod shuffle users. Any of you run into this problem using the following configurations? Any advise/recommendations/workarounds much appreciated as I've burned 3 days on this issue and I'm still stonewalled.
I personally think it's a device driver issue/bug and am searching for a way to update my Apple iPod USB device driver for Win XP. Two brand new ipod shuffles (received for Christmas 2008) are both behaving this way, so the problem most likely points to a global software issue more-so than to shuffle hardware issue.
PROBLEM STATEMENT: Driver data i/o streaming issue does not allow shuffle to sync data with iTunes after initial sync (i.e. reading the content of the shuffle is good, but writing modified content fails). Posted error message "The ipod ... cannot be synced. Required disk cannot be found". After cracking the hood on my device driver, the problem seems to point to the Apple iPod USB device driver for Win XP. Driver will recognize the shuffle and read to it, but subsequent write attempts will result in device driver balks that "this device cannot start (code 10)".
ATTEMPTED WORKAROUNDS:
*Read All "How to Get Started Manuals" to make sure I was using the right technique for syncing my two shuffles from within iTunes... tried and failed
*Ensure only one shuffle was plugged in at a time (saw notice that two shuffles plugged in at the same time is not yet a supported config)... tried and failed
*The 5 R's as recommended by Apple Support... tried and failed.
*I've tried all 3 built in USB ports on my Lenovo T60. no love... tried and failed.
*Per discussion board: From Window's Device Manager-> Scaned for new hardware while shuffle was syncing...tried and failed.
* Per Discussion board: From Window's Disk Management -> Ensured shuffle came up as a FAT32 filesystem... connection tore down as quickly as windows recognized it.... tried and failed.
*From Windows Software config utility: Ran repair to re-install itunes 8... same results.
*From Windows software management utility: Uninstalled and reinstalled itunes 8... same results.
Hardware: IBM Thinkpad/Lenovo T60. Using build in k/b & no external mouse. Has 3 USB built in ports.
Software: Windows XP Pro SP2/iTunes 8.0.2/shuffle (2nd gen) driver 1.0.4 (same behavior using the original driver 1.0.3).
Apple iPod USB Device properties:
Driver Provider - Microsoft
Driver Date - 7/1/2001
Driver Version - 5.1.2535.0
Digital Signer - Microsoft Windows Publisher

Hi. Ive got pretty much the same problem.... Got a new shuffle for christmas..having real problems syncing with itunes. Funnily enough I managed to get 25 tracks on it but then it just stopped. error message says " The ipod shuffle cannot be synced. The required disk cannot be found." Ive done restore, and downloaded a reset utility thingy to try but still no joy.

Lenovo driver issues after upgrade to Windows 10

Hi, i recently upgraded my Y50 to windows 10 after i got the notification. Now the Fn+F6 to disable the trackpad and Fn+F5 for airplane mode don't work. others seem to be working properly. I was unable to find any rivers. Also, i noticed that league of legends now runs at 60fps when uncapped, while previously it ran at about 180. I am not sure if the nvidia graphics card is being detected or if it is using the intel one.

the problem has been fixed by 1- reinstalled win 10 2- win 10 removed intel hd 5500 driver as expected , but i didnt update it manually nor by update from device manager nor make any changes , so i ran windows 10 update tool from system and made all 100% update after restart things are ok now every thing is ok and new intel hd 5500 driver has been installed by win 10 update tool : 10.18.15.4248 //driver date : 29/06/2015 also invidia 840m driver has been updated thanx for any try to help and if any one still stuck with black screen the problem is that win 10 read two monitors instead of 1 so you have to click "windows button + P while black screen already on " and try to hit and click on first choise or other choises till you can see the desktop , sure u cant see any thing while u are trying to choose but you should try or may be you connect another monitor or tv and fix this issue by win button + P good luck

Hard drive issues after update 10.10.3

Question also posted here:Hard Drive Issues (Both new and old)
I'm trapped in a HDD nightmare with my MacBook Pro mid-2012.
I updated to Yosemite 10.10.3 (with the Photos app). A couple of days after the update, I was watching a movie on my TV screen via HDMI. In the middle of the movie I removed the HDMI cable from the MacBook Pro and everything freezes. I forced shut down (Note: My HDD was encrypted). After I forced shut down, I tried to turn on and the loading screen would never stop loading - like, 14 hours stuck with the progress bar. Since I have backups, I decided to access DU and format my HDD. I tried everything. For real. Every command line I could type on Terminal to format, repair, erase and/or partition. I read almost every issue-related questions on the forums and stack exchange groups for a week (even posted my issue here: http://apple.stackexchange.com/questions/181090/erasing-and-partitioning-hard-dr ive-from-internet-recovery?noredirect=1#comment215695_181090).
So, I decided that it was a HDD failure and bought a new one.
I bought the Seagate 1TB SSHD Hybrid - ST1000LM014. Installed the new fresh disk and guess what? All those same problems again. I´m not able to restore from Time Machine because it doesn't recognize the disk in the restore page. But the disk is recognized in the DU. When I try to erase or partition the new SSHD, the same old errors: File system formatter failed. Yes, I tired GUID Partition Table, all of the security options, etc.
Please. Any light that you can throw at this issue, I'll be very grateful for. BTW, the new SSHD is recognized and the SMART Status says: Verified.
Any ideas on *** is going on?
Thanks in advance!
MacBook Pro (13-inch Mid 2012), i7, 8GB RAM

After I erase the hard drive (I assume one pass of writing zeros is good enough, 7 passes not needed?) do I turn off the laptop, then turn on and insert the Install Disk? Will there be a prompt telling me when to put in the disk? Or do I put in the disc right after erasing?
One pass is fine. If you've previously backed up your hard drive to an external hard drive using SuperDuper!, which is what I use and recommend, or another program, if it created a bootable drive, you want to boot off of it, bring up SuperDuper! and copy the drive back to the internal hard drive. SuperDuper also makes the drive bootable. When done, reboot, and you should be all set. If you're using Time Machine, you'll want to install the operating system, then restore the Time Machine backup. SuperDuper! is available from http://www.shirt-pocket.com/superduper/superduperdescription.html
Finally- should I update the OS? Is there a problem with the newest update that caused this crash, or was it just a spurious glitch/bad luck?
I've been running 10.5.8 for awhile with no issues, and would recommend moving to it.

Driver issue after Downgrading to Windows 7 (Pavilion 17-f081no)

So,i went to downgrade yesterday,and have had this problem ever since. Nothing works except one USB port at the right side of the laptop (when looked at front),no usb connections,no wireless or wired connection,nothing. They are all dead,including SD card slot.
I know its the driver issue,but i cant seem to find them. I need something for USB ports,Ethernet/Network card/,SM BUS controller etc. They are all listed under "Other devices" in Device manager.
What drivers should i be getting? I have been trying to google,but i am starting to feel really hopeless here.
My wireless card info:
PCI\VEN_10EC&DEV_B723&SUBSYS_2231103C&REV_00
PCI\VEN_10EC&DEV_B723&SUBSYS_2231103C
PCI\VEN_10EC&DEV_B723&CC_028000
PCI\VEN_10EC&DEV_B723&CC_0280

Hi:
First install the amd chipset drivers and reboot.
http://support.amd.com/en-us/download/chipset?os=Windows%207%20-%2064
See if the generic amd graphics driver works...
http://support.amd.com/en-us/download/mobile?os=Windows%207%20-%2064
Ethernet: DL and install the second driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=7&Level=5&Conn=4&DownTy...
Wireless:
http://h20564.www2.hp.com/hpsc/swd/public/detail?swItemId=ob_143747_1
Bluetooth:
http://h20564.www2.hp.com/hpsc/swd/public/detail?swItemId=ob_142906_1
Card reader: DL and install the first driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=15&PFid=25&Level=4&Conn=3&DownT...

Satellite R630 - Driver issues on Win 7 64bit after SP1 upgrade

Need your help here guys,
My Satellite R-630 is less than a year old, running a Windows 7 Home Premium on 64 bit. For a while, I have been experiencing BSOD's, which I traced through the Event Viewer to here: http://technet.microsoft.com/en-us/library/dd337789(WS.10).aspx
This did not lead me far enough.
Finally, I concluded through other forums that the SP1 upgrade would solve some of the annoying BSOD issues and I launched the download and upgrade. However, on restart, while my laptop seems to have been cured (so far) of the BSOD's, I have issues with drivers for:
- Sound Card
- USB Controllers
- DVD Player
- Webcam
- Bus Enumerators
I have downloaded the indicated Win 7 - 64 bit drivers in each case. I tried installing them first. Nothing happened. I uninstalled the existing drivers, and installed them again. Nothing happened again.
I figured I must be doing things in the wrong order.
So I tried installing
1). the Chip Set Utility (drivers?) first, then
2). the USB drivers
3). Sound card drivers etc.
Nothing is happening still.
I am running out of ideas here.
P.S While all the other drivers executed fine when I extracted them from the .zip format, the Sound card driver refused to execute, even though the "run command" box was ticked when the .msi file was run.
I extracted it into a folder and ran it manually.
Still didn't help.

That's where I got things wrong I think. I did not use the windows automatic update, because it kept saying connection was unsuccessful.
What happened is it identified a component of the SP1 as a "critical update", a 900 mb chunk (listed as windows6.1-KB976932-X64.exe here: http://www.microsoft.com/download/en/details.aspx?id=5842 ) but would not download it. It failed every time. So I went on the windows download centre, looked up for the same component and installed it manually. Right now windows update turned green with the tick and says everything is fine.
I will try to restore my settings to the former configuration and let you know. I was about to try that last night, but I didn't see any restore date prior to the SP1 installation. I'll try this right now.
--*Edit:* So system restore isn't working. There is only one restore point that's prior to the SP1 installation. I've tried 3 times already. Every time it tells me that it could not access a file, probably because of antivirus. I use Avira. I disabled it the second time. Still same message. I uninstalled it completely for the 3rd trial, same message again.--
--So system restore isn't an option. Could it be that I missed a component that would be required for some drivers to work properly after the update?--
*Edit*: In all my troubles, I forgot an elementary step: run system restore in Safe Mode. Which I did. Now my system is back to before SP1, sound, usb connectivity working. I suppose everything is back where it should be. I'll just wait and see if i get a BSOD again and come back here if need be.
Thanks guys.
Message was edited by: 1132nd
Message was edited by: 1132nd

Help on small issues after WinXP downgrade from Vista

Lenovo 3000 v200
I recently downgraded from Vista to WinXP Professional, and I must say I'm much happier with XP.
Some issues on the install: although I downloaded all drivers from the Lenovo site, the install didn't work from my usb floppy drive.
It recognized the floppy on the F6 portion of the install, but then later it kept asking for the disk to be inserted (it was already in the drive). Workaround was to install by changing to "compatibility mode" in the BIOS, and after install, loading all drivers and changing BIOS back to SATA.
All features of the laptop appear to work perfectly; camera, fingerprint reader, wifi, etc.
HOWEVER: in the device manager, there are 3 yellow exclamation points in the "Other Devices" section, and each of them is labeled "Base System Device." Does anyone know what these are? Why are they not recognized as specific devices? LenovoCare doesn't recognize them either, and I have no idea what drivers to attempt to install for mystery devices.
Also, "Modem Device on High Definition Audio Bus" won't install. I have the current driver, and I've tried updating from LenovoCare, but no luck. As I don't use a modem, this seems irrelevant, but I'd like to install it just the same if possible.
Finally, the LenovoCare recognized a need to install a "Hotkey" update, and it claims to successfully install, but everytime I run LenovoCare it says I need it again. Any comments or observations?
Again, the computer works just fine even with these small issues. In fact, it is better than fine; it is a joy to use and a real speed demon with XP instead of Vista. So I'm not trying to do any rocket science or potentially screw up a very nice situation, but I am trying to iron out these small nuisances.
Thanks to all of you who consider my trivial problems. I really appreciate having knowledgable individuals like yourselves help out a very modestly skilled, but reasonably ambitious user.
Cheers,
Fred

Hello Fred,
I created a blog on this forum called.... "I Explain How To Downgrade From Vista To XP Successfully On A 3000 N100 Laptop" Locate this message and read through it. Try the "Auto Detect This System" I Talk about. It will load the latest drivers and the latest...BIOS..... for your particular model if you have not already upgraded it. You did not mention if you had upgraded your BIOS...... if your running an "OLD" version.... THIS..... could be your problem.
Regards

HP Envy dvd drive issues after the Windows 8.1 update

I have a HP Envy and after the Windows 8.1 update the dvd drive is not working. I can see the drve but it is difficult to get the drive to open or recognise there is a disc in it. What can I do?

Hello @Jenino,
I understand that you are having issues with the Optical Drive on your HP ENVY 7 PC. I would be happy to assist you, but first I would encourage you to post your product number for your computer. I am linking an HP Support document below that will show you how to find your product number. As with this I can provide you with accurate information.
How Do I Find My Model Number or Product Number?
Please re-post with the requested information and I would be happy to provide you with assistance. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

CD Driver Issues after installing 11.1.4

After installing Itunes 11.1.4, my HP computer, running Windows 7, could no longer find the CD drive. Upon investigation, someone suggested I update my registry to remove some entries. I did the following:
Start, enter regedit in search bar,
Open regedit
Left hand menus click HKEY_LOCAL_MACHINE
SYSTEM
CURRENT CONTROL SET
CONTROL
CLASS
Then need to find {4D36E965-E325........... (are more figures but not needed)
on right hand window see if there is an upper filter or lower filter.....right click and delete the values if either are there.
RESTART...
This worked, but now Itunes complains every time I open it, saying some registry settings are missing for my CD drivers. I've used Itunes on this computer succssessfully for years, until this upgrade. Apple, whatever you did, please undo it. Horrible release...

Solving the iTunes Installation Problems in Windows
1. Apple has posted their solution here: iTunes 11.1.4 for Windows- Unable to install or open - MSVCR80 issue.
2. If the Apple article does not fully resolve the problem for you, then try Troubleshooting issues with iTunes for Windows updates - MSVCR80.

Bluetooth Mouse Driver Issues after updating to SP1

Greetings!
After upgrading to SP1 my bluetooth mouse stopped working. The dongle I'm using is being detected fine, and when I scan for the mouse I can find it, but when I try to connect to it I get a "Locate driver" message from Vista. When I let it scan for the driver it is unable to find anything compatible, so when I tell it to scan the CD that came with it again it finds nothing. It's like the Bluetooth HID Device driver is no longer working.
This is the dongle:
http://us.kensington.com/html/9403.html
This is the mouse:
http://us.kensington.com/html/12635.html
Some of the things I've tried:
Uninstalling and reinstalling the WIDCOMM Bluetooth stack. I've tried using Vista's Bluetooth stack instead of the WIDCOMM stack, with no luck.
I've also tried the Bluesoleil drivers with no luck there either, in fact those seem to break the dongle and Vista is no longer able to detect it.
I've tried the install CD that came with the mouse, but it seems that is for Windows XP only.
I've tried another Bluetooth mouse that produces the exact same results, with a CD that is for Vista.
Anyone else having this issue?

Just wanted to update this with an answer.
I'm pretty sure that running vsp1cln.exe was the reason why my Bluetooth and iPod stopped working. I reinstalled Vista and upgraded to SP1 without running that tool to clean up the install files and both bluetooth and my iPod are working again. It must clean up the driver files that they were using and the new files are not compatible or something. Not sure really.

Satellite P870 - WiFi issues after Win 8.1 upgrade

Internet through wireless is hopeless.
Maybe 3 in 10 pages will load correctly or not at all, mostly not at all.
Other wireless devices in the house are fine, as is using the Ethernet .
Checked the drivers through the device manager, says they are up to date.
However using the toshiba service station it lists 12 updates including one for the Realtek wireless driver.
The date of release definitely after the current installed version.
Trying to update through the service centre it completes and then comes up with an error message, something like process ended by the user.
Of course I never ended anything.
Any ideas/thoughts? Just uninstall 8.1?
Though I would rather not.

Hi
Did you follow the Win 8.1 installation instruction?
The Win 8.1 drivers should be installed in the right order!
I found this info on the Toshiba EU driver page;
1 Intel Wireless Display -> Uninstall
2 Windows 8.1 update -> Install
3 TOSHIBA Desktop Assist-> Upgrade
4 Intel Display Driver -> Upgrade
5 NVIDIA Display Driver -> Upgrade
6 Intel Rapid Storage Technology Driver -> Upgrade
7 NVIDIA HD Audio Driver -> Upgrade
8 Atheros Wireless LAN Driver -> Upgrade
9 Realtek Wireless LAN Driver -> Upgrade
10 Realtek Bluetooth Filter Driver Package -> Upgrade
11 TOSHIBA System Driver -> Upgrade
12 TOSHIBA Function Key -> Upgrade
13 TOSHIBA eco Utility v2 -> Upgrade
14 TOSHIBA PC Health Monitor -> Upgrade
15 TOSHIBA Fingerprint Utility -> Upgrade
16 TFPU WBF Delete Fingerprint Tool -> Upgrade
17 TOSHIBA HDD Protection -> Upgrade
18 TOSHIBA VIDEO PLAYER -> Upgrade
19 TOSHIBA Blu-ray Disc Player -> Upgrade
20 ArcSoft TV5.0 -> Upgrade
21 TOSHIBA Resolution+ Plug-in for Windows Media Player -> Upgrade
22 CyberLink MediaShow 6 for TOSHIBA -> Upgrade
23 TOSHIBA Media Player by sMedio TrueLink+ -> Upgrade
24 TOSHIBA Service Station -> Upgrade

Google Drive Issue After OS X 10.9.3 Installation

Hello,
Since last week when I install the latest Mavericks version, i.e., the OS X 10.9.3, my Google Drive folders isn't working anymore as should be.
The status icon in the folder and in the files disapear!
I uninstall the Google Drive and installed again and everything come back (working again) until the next reboot.
Then the status icon disapear again!
Any tips about this issue?
Thanks.
Regard,
Before:
After:

I founded that this is a Google Drive known issue on Mac:
https://support.google.com/drive/known-issues/2458941?hl=en&ref_topic=14951
Sync status icons missing on Mac
After you install Google Drive for your Mac, you should see sync status icons next to file names in the Google Drive folder on your computer. If you don’t see these icons, try restarting the application.
Open the Google Drive menu from the toolbar at the top of your screen.
Select "Quit."
Restart Google Drive by opening it from your Applications folder.
Enter your Mac username and password (not your Google Account information).
The sync status icons should now appear in your Google Drive folder.

Audio and video issue after Win 10 Upgrade - Split X2 laptop 64-bit

Any solution to the Audio and Video issues on Split X2 13" laptop after Windows 10 FREE Upgrade?? - Intel Core i5 processor- 4GB memory I'm sure others are have the same Audio/video problems: - there is Sound and video playback but the sound and video is repeated slowly forward....impossible to understand the audio. The video is clear but also being played in repeated frames as it moves slowly forward!- sounds coming out of the speakers ok - everything was working great on Windows 8.1 (before upgrading to Windows 10). there must be some kind of driver upgrade for IDT High Definition CODEC BEATS audio... is there a work-around until a real fix is provided?? Regards - VK

I have downloaded and installed the HP recommended IDT Audio Driver using the HP Assistant. The current installed IDT High Definition Audio CODEC driver is: STWRT64.sys 6.10.6498.0 The laptop was rebooted but the problem still the same.....Audio is garbeled and impossible to understand the words...video seems ok when playing Youtube videos. My Split 13 X2 product id is: E2S66AV BIOS F.27

Audio and (sometimes) video issue after Win 10 Upgrade - Split X2 laptop 64-bit

Any solution to the Audio and Video issues on Split X2 laptop after Windows 10 FREE Upgrade?? I'm sure others are have the same Audio/video problems: - very slow, Repeating audio and video on YouTube and Netflix playback....totally unwatchable- speakers work fine- everything was working great on Windows 8.1 there must be some kind of driver upgrade for IDT High Definition CODEC BEATS audio... is there a work-around until the real problem is fixed? Regards - VK

I have downloaded and installed the HP recommended IDT Audio Driver using the HP Assistant. The current installed IDT High Definition Audio CODEC driver is: STWRT64.sys 6.10.6498.0 The laptop was rebooted but the problem still the same.....Audio is garbeled and impossible to understand the words...video seems ok when playing Youtube videos. My Split 13 X2 product id is: E2S66AV BIOS F.27

CR52 (MS-8352M) 52x32x52x CD-RW Drive - Issue after trying to update the Firmwar

I have the CR52 (MS-8352M) 52x32x52x CD-RW Drive and I'm running Windows XP.
I noticed that I was having issues with CDRW's and my drive was reading data very slow, but I had no issues burning CD-R's.
After finding that the current firmware was 1.70, I decided to update the firmware to 3.70.
Halfway through the firmware it gave me an IDE Error (forgot the actual code, but it just bascially said it could not rerad a present drive).
Now when I boot up, there are no lights coming from the CD drive.
is this drive now dead because of an improper firmware update?

I guess that you have a bad flash of the firmware. I suggest that you flash in Safe Mode and best with only that particular drive that you want to flash to be connected to the controller.

Driver issue after win 8 downgrade

Similar Messages

Maybe you are looking for