Driver Setup for PXI 2569 and PXI 2529 in Switch executive

Hi,
What sould be tha "Driver Setup" for PXI 2569 and PXI 2529 in Switch executive under 'Driver Session"
Regards!!!
Vineet Shukla

Hi Vineet,
You do not need to insert anything under Driver Setup.  Anytime you are using NI switches, you can simply click Configure NI Switches when creating a NI Switch Executive Virtual Device to configure the topology settings of those switches.
Just so you know, you can insert information under Driver Setup, and then you wouldn't have to use the Configure NI Switches wizard.  More detail on what to insert under Driver Setup can be found in the following KnowledgeBase:
How Do I Create a Virtual Switch and Use it in my Application?
http://digital.ni.com/public.nsf/websearch/A1F0D6A3357E14B386256E4B0071FDA2?OpenDocument 
In short, you would type "Topology:" followed by the topology name such as "2569/100-SPST" or "2529/2-Wire 4x32 Matrix".
Let me know if you have further questions or if this does not resolve your issue!
Chad Erickson
Switch Product Support Engineer
NI - USA

Similar Messages

  • Error -1074118625 with PXI-4071 and PXI-2527

    When using the LabVIEW IVI drivers for PXI-4071 and PXI-2527, I receive an error -1074118625 in TestStand.  The sequence initializes the MUX, init DMM, connects the MUX, waits for debounce, and then upon reading from the DMM, I receive this error.
    Error: niDMM Read Waveform (waveform data).viExplanation could not be found for the requested status code.
    Verify that the requested status code is correct.
    [Error Code: -1074118625, User-defined error code.]
    This sequence of events is successfully used multiple times elsewhere in the TestStand.  This error does not appear in any knowledgebase article nor in any help.  Any explanation would be greatly appreciated.
    Solved!
    Go to Solution.

    I found this with google that seems like it might apply:
    http://digital.ni.com/public.nsf/allkb/A593DEBFD86A69C68625727900748EEC

  • Is there an output switch at the analog front end of PXI-6723 and PXI-6713?

    I was reading the analaog output user manual and i could not find this. Is there any output switch just before the analog output of each channel for PXI-6723 and PXI-6713? I am would like to have total isolation between when these output are not needed. If yes, is there any specification to refer to?
    Thanks.

    Hello Chris,
         I would recommend having a look at the examples in the LabVIEW
    example finder to start with. In particular i would look at 'Cont Gen
    Wfm-Ext Clk.vi' This is a basic example that allows you to output a
    waveform through the card and source an external clock source to do
    this. I would recommend exporting the sample clock that you wish to use
    from the 4462 on one of the RTSI lines and then setting this as the
    sample clock source for the Analog output card.
    Another good example to look at is the 'Cont Gen Voltage Wfm-Int Clk
    non regeneration.vi' This does not regenerate the same waveform in the
    buffer but instead creates a new waveform to output after the previous
    one has been written to the buffer.
    It should be noted that there may be some gliltching if you are
    updating the waveform. This is because the buffer will already have a
    waveform in there to output before you input the new one so a new
    frequency may not have an exact number periods that fit into the
    pre-defined buffer. If you are looking to generate dynamic waveforms
    then the best option for the best results would be one of our arbitrary
    waveform generators here.
    Good Luck,
    LeeM
    NIUK

  • External hard drive setup for time machine reading as a virtual cd

    Why is my MacBook Pro reading my external hard drive setup for time machine reading as a virtual cd?
    Thanks

    Hi Christian,
    Is this something that has happened from the start? If so, I would reformat the disk and setup TM from scratch again.
    Prepare the external HD by connecting to the Mac, open Disk Utility, select the manufacturer’s name of the external HD, select Partition and choose GUID Partition Table, format to Apple OS Extended (Journaled); quit Disk Utility.
    Open System Preferences.
    Click on Time Machine.
    Click on “Select Disk.”
    Click just to the left of "On" to turn TM on if it's not already on.
    Click on the disk or partition you want to use.
    Click on “Use for backup.”
    Leave external HD connected, and TM will automatically do its thing.

  • How to build FM radio receiver on PXI 5600 and PXI 5142 with help of labview

    How to build FM radio receiver on PXI 5600 and PXI 5142 with help of labview?
    PLZ TELL ME!
    Solved!
    Go to Solution.

    Dude,
    Your way of asking questions sucks!
    - Do not use such fonts!
    - Try to find things out yourself first (apparently GovBob was able to find info, so could you)
    - Have you asked GovBob if he likes it that you mail him for more questions?
    You ask for a complete solution on a project YOU have to do. (you dont learn of it if you dont try it yourself first)
    Hopefully you will ask questions in a less DEMANDING way next time.
    Good luck with your project

  • Why modulation and demodulation with PXI-5673 and PXI-5663 was wrong%3F

    iam using PSK-demodulation-modulation  example found in find examples to perform modulation-demodulation for the transmitted signal iam using PXIe-5673 and PXIe-5663 as VSG-VSA 
    i found that the received bits not as the transmitted bits any help in this issue

    iam sending PN sequence or user defined pattern 01010101 
    the received is not as the transmitted 
    here i attach the code
    Attachments:
    MT RFSG Generate PSK.vi ‏53 KB
    MT niRFSA PSK Demod.vi ‏89 KB
    PN_Sequence_09.txt ‏2 KB

  • I have a tesco router and an external hard drive attached to it as a network drive (shared) for my macbook and MB-Air. Have no problems with my MB accessing it, but with MB-AIR it says -  'the version of the server you are trying to connect to is not supp

    I have a tesco router and an external hard drive attached to it as a network drive (shared) for my macbook and MB-Air. Have no problems with my MB accessing it, but with MB-AIR it says -  'the version of the server you are trying to connect to is not supported. pls contact your system administrator to resolve the problem'. MB-Air uses maverick downloaded yesterday - upgrade from mountain lion. MB uses snow leopard still, as i am quite used to it and am thinking of upgrade if mavericks work fine on air. Also have parallel on snow leopard but it is no longer supported according to mac website - if i upgrade am i going to lose my parallel and will have to buy a new one!!!

    Yes, the Old Master file has a folder for each year where I find all photos from that specific year. I am attaching a screen shot of the file.
    In the meantime i have managed to download all photos (it did not download any video files though in mpg, avi, 3gp, m4v,mp4 and mov format) to a new iphoto library. Unfortunately the photos are quite mixed and often doubled up. I ma considering to purchase iphoto library which checks all duplicates in iphoto. this will save me a lot of time. What do you think?

  • Can I set up multiple usb hard drives- one for time machine and a second for media? Can one also print wirelessly with an old HP C6280 printer?

    Can I set up multiple usb hard drives- one for time machine and a second for media?
    Can one also print wirelessly with an old HP C6280 printer?

    Can I set up multiple usb hard drives- one for time machine and a second for media?
    Yes.
    Can one also print wirelessly with an old HP C6280 printer?
    Possibly by using an Airport Express, but depends on what type of port connection the printer requires.

  • Document Types Setup for Expense Approval and Payable Invoice

    Hi,
    Can anyone please suggest Document Types Setup for 'Expense Approval' and 'Invoice Approval' and its tables related to the same. Table storing its document_type_code and wf_approval_itemtype as we have for PO_DOCUMENT_TYPES_ALL table for Purchase Order.
    Thank You.
    Regards,
    Meghana

    Hi
    It could be because of main memory problem... so Restrict your selections and do the statistical setup
    by the way how many comp codes you have? restrict with comp codes or doc ranges
    Thanks,

  • JDBC Thin Driver Support for Data Encryption and Integrity

    Hello JDev Team,
    I am trying to implement JDBC Thin Driver Support for Data Encryption and Integrity.
    It works fine with java.sql.Connection and java.util.Properties like in the following code:
    DriverManager.registerDriver(new oracle.jdbc.driver.OracleDriver());
    Properties props = new Properties();
    int level = AnoServices.REQUIRED;
    props.put("oracle.net.encryption_client", Service.getLevelString(level));
    props.put("oracle.net.encryption_types_client", "( RC4_40 )");
    props.put("oracle.net.crypto_checksum_client",Service.getLevelString(level));
    props.put("oracle.net.crypto_checksum_types_client", "( MD5 )");
    Connection conn = DriverManager.getConnection ("jdbc:oracle:thin:@localhost:1521:main", props);
    etc...
    But I am developing an application with InfoSwing components and it has a different way to connect to Oracle database using oracle.dacf.dataset.connections.Connection, like this:
    sessionInfo1.setAppModuleInfo(new ModuleInfo("bc", "BcModule"));
    sessionInfo1.setConnectionInfo(new LocalConnection("JDBCThin"));
    sessionInfo1.publishSession();
    My question is:
    Is there any way to implement DataEncryption and Integrity into this type of connection?
    Thanks a lot in advance.
    Victor Bykov
    null

    Victor,
    No, you can't do this from DAC, but I've been discussing it with the developer, and we both think this capability would be useful to have, so I've logged it as an enhancement request.
    I do have a question for you. Once you've made the JDBC connection, do you need access to the Connection object afterwards? We're thinking of how the change could be implemented, and one way would be to allow you to pass in a Properties object when creating your own NamedConnection.
    Thanks
    Blaise

  • Swapping hard drives between PXI-8115 and PXI-8105 won't boot up

    I have a test system running Windows XP on PXI-8105.  I've upgraded the entire test system for another project and need to upgrade my existing systems; the upgrade runs on Windows 7 and PXI-8115.  I have new hard drives with Windows 7 and the new test software which were loaded/configured/tested on a PXI-8115, but I need to retrofit the PXI-8105 with them.  This doesn't work.  Windows begins to boot but fails and tries over and over again.  In an effort to take the PXI-8105 off-line to troubleshoot, I replaced it with one of the PXI-8115 and the old (WinXP) drive.  This didn't boot up, either.
    Here's a summary of my situation:
    An old system has PXI-8105 running WinXP
    A new system has PXI -8115 running Win7
    A hard drive (with Win7) from the PXI-8115 won't boot on the PXI-8105
    A hard drive (with WinXP) from the PXI-8105 won't boot on the PXI-8115
    What is different between the two PXI controllers that keeps me from swapping hard drives?
    Jim
    You're entirely bonkers. But I'll tell you a secret. All the best people are. ~ Alice
    Solved!
    Go to Solution.

    A couple thoughts:
    1. Windows 7 probably works fine on a PXI-8105. Although NI never officially supported or shipped that configuration, I suspect that the default Windows 7 installation contains enough of the driver support needed to boot up.
    2. In general, Windows is not very tolerant of swapping hard drives between completely different systems, especially with Windows XP and prior. Consider whether just installing fresh and copying over what you need is faster than trying to do this, but if you must, I would suspect that Windows 7 would be more tolerant of the swap.
    3. As a debugging step, try pressing 'F8' during the boot process to launch the Windows boot menu and try safe mode or some of the other options.  More information here.
    4. If all else fails, Google is your friend here as there's nothing particularly specific about this being an NI product that you need to know when attempting this operation. Any information you find online about swapping hard drives between PCs should be relevant to your situation. Searching for 'swap hard drive to new computer windows 7' gave some useful hits on the first page. Beyond that, you can also look into using the 'sysprep' utility to try and clean the system and prepare for swapping to a new PC.

  • MAX does not detect my PXI-5122 and PXI-6551 cards in a PXI-1045 chassis.

    I have been using a PC with MXI-3 to PXI-1045 chassis to develop LabView TestStand code.  Things are fine on my development PC.  [Software configuration report attached nireport_rich.txt].
    I have a 2nd PC set aside to test my deployment packages.  I installed a GPIB card and MXI-3 card in my deployment test PC, and loaded a bunch of hardware drivers.  [Report attached nireport_depPC_0006.txt]
    All the PXI cards are found just fine when my development PC is connected, but when I power up my deployment PC (with MXI-3 connected to the 1045 chassis) -- I can't import the development configuration [exported from development PC] because the deployment PC does not see the PXI-6551 DIO card in slot 6 [PXI6::10::INSTR] and the PXI-5122 card in slot 13 [PXI8::15::INSTR].
    I keep reviewing the hardware driver versions installed, and the only small difference that I see at this point is that the deployment PC has a slightly older version of NI-Switch.
    Anybody have any ideas of what I can try next?  I'm out of ideas.
    . . . . hmmm, can't seem to attach more than one file, so here's the software info on the deployment PC
    NI Software Information:
    CVI Run-Time 7.0.0.395
    NI-DAQ 7.3.0f1
    NI-DAQmx 7.3.1f0
    NI Script Editor 1.1
    NI-DMM 2.3.1
         Soft Front Panel 2.3.0
    NI-FGEN 2.2.1
         FGEN Soft Front Panel 2.2
    NI-488.2 Software 2.30
    IVI Compliance Package 2.2 2.2
    LabVIEW Run-Time 7.0
    Measurement & Automation Explorer 3.1.1.3003
    Measurement Studio 6.0
         For Visual Basic 
              ActiveX User Interface 7.0.0.344
              ActiveX 3D Graph 7.0.0.344
              ActiveX DataSocket 4.2.2.1
    NI-USI 1.0.2
    NI-HSDIO 1.2.1.3
    NI-HWS 1.2.2.0
    NI-PAL Software 1.8.2.0
    NI-SCOPE 2.7.0f5
         SCOPE Soft Front Panel 2.1.0
    NI Spy 2.2.0.12
    NI-SWITCH 2.30.49153
    NI-TClk 1.2
    TestStand 3.1
    NI-VISA 3.2
         visa32.dll 3.2.0.19
         NiVisaServer.exe 3.2.0.19
         NIvisaic.exe 3.2.0.19
    LabVIEW Run-Time 7.1

    Hello Maggie,
    Appreciate your assistance and reply.
    The pxisys.ini and pxiesys.ini files are modified by me with referring to
    1)PXI System Alliance PXI-2 SW spec,
    2)PXI-6 SW spec,
    and 3)pxisys.ini pxiesys.ini generated by MAX v5.3.0f0 with NI PXIe-1075 + NI PXIe-8133.
    The content in pxisys.ini/pxiesys.ini generated by MAX looks like simple. Consequently, I modified and checked it line by line according to actual hardware of PXES-2590+PXIe-3975. Then, MAX just list devices as described in the first post. I tried to find the root cause but in vain.
    Is this minor issue can be related any incorrect tag lines in pxisys.ini or pxiesys.ini I posted?
    Is any suggestion tests I can do to troubleshoot root cause?
    Looking forward your reply.
    Cheers,
    KL Tseng

  • Hard Drive Setup for Creative Professional

    Hi. I own a Mac Pro 3Ghz tower, and I only have one 250Gb hard drive along with an Iomega external 250Gb hard drive. I really need to upgrade my hard drives and create proper backups. I'm just not sure about the best options for backing up all my data and what the best options are for setting up my harddrives. Can anyone offer advice to a graphic designer that needs to upgrade his hard drive setup? I'm not sure what Raid is, so I would need to better understand what that does as well. I guess I need a road plan for the best way to go about all this upgrading.
    Thanks.

    Hi There,
    I know you posted this more than a month ago, but i thought i'd see what you found and...what you can offer me in the way of answers. I appreciate any help you can give me!! Thanks in advance. I might have a couple options for you too.
    I have the same set up pretty much. 1 250gb internal, 1 250 gb external, plus a 175gb external that i keep off site. Files are everywhere, yes i have copies, but it's an organizational disaster and not fail safe. If i lost a clients job, i'd loose more than the cost of just setting up a good backup system.
    I found a few things out.
    You can set up a software raid on your macpro using disk utility(although I don't know how to do it yet). (for raid info, look up raid on wikipedia, it's just a variety of ways to create more than one copy of data on any # of drives. 2 drives is a mirror image, 3 can be striped(any one drive can fail), and more...there are speed advantages with these too. )
    Anyway i have 3 bays open for drives in my 2.66ghz quad. So setting up a software raid is option 1 - but from reading forums it seems like this isn't easy and requires maintainance? If you add a drive or remove one it erases all drives(?).
    There is a system my friend turned me on to called Drobo.
    It seems like the easiest solution and one that is lasting, check out the website at drobo.com it's external, has 4 bays and you can add and remove drives on a whim and upgrade up to 4tb. seems the easy solution, but costs 500 and then you need to purchase drives. but you can use any drives and it seems maintanance free.
    Any recommendations - is software raid easier than I imagine?
    Anyone have any offsite storage ideas? (.mac would be ideal, but it costs so much for storage and it's slow).
    Looking forward to hearing your solution, and any advice for me.
    Thanks,
    Josh

  • Media/Disk cache, etc. setup for a desktop and laptop dual configuration

    Hi,
    (New User)
    I have a desktop at home, and a laptop.  I split my time about 50/50 between the two.  I use it for AE, PP, PS mainly
    Desktop hard drive setup:
    1 SSD (Currently, Windows 8 and Adobe CC installed)
    2 - 1TB (7200rpm) drives (1 drive is where I put my project files (gets sync'd with google drive) and the other drive isn't being used at the moment)
    Laptop:
    1TB Hard drvie (Of course, Win 8 and Adobe CC installed)  (And, the folder where I do my projects gets sync'd with google drive).
    As you can see, because I split my time between a laptop and desktop, I need to be working with the most current files (which is why I sync them through google drive).
    My question is (please remember I am new), where should I set up disk cache, media cache, and anything else so that it is effecient and more importantly so I can use either my laptop or desktop to work on the same files?
    Again, I barely know what I am talking about here.  I really don't understand what media cache, disk cache, etc. is.  I am trying to learn but I want to get this setup first so I can start with the tutorials on lynda.com.
    Thanks,
    Chris

    First you do not need disk cache for all projects. For some it may even get in the way. Second, put your disk cache wherever you would like. If you have a second drive that is fast, use that. If you have room on your SSD drive, use that.
    If you get into trouble with a comp and previews are fouled up or things just don't look right, empty your disk cache. It's not a necessity for working with AE, it's just a convenience for some projects that may help you work a little faster.

  • Peer to peer between PXIe-5451 and PXIe-7966R

    Hello,
    I would like to connect two devices - PXIe-5451(waveform generator) and PXIe-7966R(NI FlexRIO) with P2P streaming. I want to transmit data from FPGA to generator and i took example from NI-FGEN. When i'm starting host-vi, there is an error occured (see picture).
    What i'm doing wrong?
    Solved!
    Go to Solution.

    So, i'm solved this problem. It was my mistake. I picked the wrong resource name for my waveform generator. But now i have another problem. "Unknown channel or repeated capability name" error occures, when i'm starting VI.
    Attachments:
    1.png ‏164 KB
    2.png ‏208 KB

Maybe you are looking for