Driver Status: (Hex 0xBFFC09F0) ERROR: Instrument status error
I have been receiving this problem in my program. I'm using RTO1002 and using LABView to run my program. I have checked with R&S that this is indeed the correct driver for my program. Can anyone please advise me? Thank you.
Hello,
For the problem description it seems that you have downloaded the instrument driver for this Tektronics scope. If you haven�t you can look for one in ni.com at the Developer Zone or just do a search at the top with the model number of the scope.
One thing you need to check is if the driver version that you have is for the version of LabVIEW that you have and also to check if you don�t need to upgrade any other software and if it is compatible with the OS that you have.
Probably by reinstalling the driver it would fix the problem. You can try on a different computer and see if you have the same problem.
If you still have problems after troubleshoot a bit more, then please provide more information as the scope model numbe
r, driver version, OS, LabVIEW version, 488.2 version, etc.
Thank you
Best Regards
Ricardo S.
National Instruments.
Similar Messages
-
Hi NI.
I'm trying to aquire signals from an Tektronix DPO2014 oscilloscope using Labview SignalExpress.
I have downloaded and installed the appropriate driver (at least I think )) : tkdpo2k using NI download station.
I run an ethernet connection and I do see the device in MAX, however im not quite sure if I have configured the IVI driver sessions correctly.
Anyway, when I open Signal Express, and select "IVI scope aquire" I can select my device under "resource descriptor" and the appropriate driver under "Instrument driver". I then turn on my Oscilloscope, tune in the machines tachogenerator, which is the signal the oscilloscope is to measure, and then select "autosetup" The sinosoidal waweform shows up on the oscilloscope and in SignalExpress, it is only done once. I then try and run the program and the error message accurs:
Timeout.
<ERR>Driver Status: (Hex 0xBFFA2003) Max Time exceeded before operation completed.
Is the problem regarding problems with triggertime or write/read problems with the TCP/IP connection?
What can I do to fix this problem?
Best Regards
Danny Joergensen
University of Aalborg Denmark
Attachments:
MAXscreenshot.png 265 KB
device.png 320 KBHow are you communicating? GPIB? Are you sure you have the correct address. Can you send an IDN command with MAX? Does MAX see the instrument?
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps -
I am trying to get a reading from the KE6487, but I am receiving the following error.
"KE6485 Initialize.vi<ERR> Driver Status: (Hex 0xBFFF0015) Timeout expired before operation completed."
The driver I download for this device is KE6485, but is also compatible for KE6487. Therefore I think it should not be a problem.
I have attached the VI I'm using for your consideration.
Please advice, thank you for your time
Attachments:
Capture.PNG 5 KB
Capture 1.PNG 21 KB
KE6485_ZeroChk_LV6.vi 45 KBHow are you communicating? GPIB? Are you sure you have the correct address. Can you send an IDN command with MAX? Does MAX see the instrument?
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps -
Hi,
I have received this trap from the Call Manager PUB server running version 7.1.5.31900-3
hwStringMatch - cmaidad[5579]: Physical Drive Status Change: Slot 1 Port 2l Box 1 Bay 1. Status is now Predictive Failure
I have checked the drive status via CLI and all drives show OK, both physical & logical
Is there anywhere you can check what is causing this event and is it merely advising of a potential drive failureHi
Modern drives have embedded monitoring. Whilst the disk hasn't failed, something internally is telling the embedded monitoring that it may soon fail - it's running a little hot, having excessive write errors, latency is drifting up... something subtle is going wrong.
It could be caused by a firmware error... but I'd take it at face value.
It might have failed by the time you read this, or it might work fine for another 20 years.
Either way - when I was a server admin I would get any disk with a predictive failure swapped out immediately. No point waiting for it to fail - even on a RAID system when a disk fails although you don't lose data you have your trousers down as a coincidental second failure would ruin your day!
Regards
Aaron -
Server Monitor Notifications - Drive Status Changed - Time Machine
I'm using an Xserve as a file server for a small workgroup . It has a Raid 1 set which is being backed up via Time Machine to an attached disk array.
Whenever Time Machine runs (every hour), I get two notifications from Server Monitor that the drive status has changed:
*Reason(s) for notification:*
*Drive status changed*
The timestamps on the notifications coincide with these messages in system.log
Feb 2 11:28:05 ciesaxserve2 Server Monitor[854]: * _NSSocket.m:243 read() failed; socket=0x197060 error=(NSPOSIXErrorDomain,61)
Feb 2 11:28:05 ciesaxserve2 Server Monitor[854]: * _NSSocket.m:243 write() failed; socket=0x197060 error=(NSPOSIXErrorDomain,61)
Feb 2 11:28:05 ciesaxserve2 Server Monitor[854]: * _NSSocket.m:243 read() failed; socket=0x2090e90 error=(NSPOSIXErrorDomain,61)
Feb 2 11:28:05 ciesaxserve2 Server Monitor[854]: * _NSSocket.m:243 write() failed; socket=0x2090e90 error=(NSPOSIXErrorDomain,61)
and:
Feb 2 11:28:55 ciesaxserve2 servermgrd[78]: servermgr_backup: TimeMachinePostBackupHook called.
Feb 2 11:28:55 ciesaxserve2 servermgrd[78]: servermgr_backup: TimeMachinePostBackupHook done.
The notifications simply report that all is normal, and the number of available drives goes from 6, to 7, back to 6. Something to do with making the backup volume available, I presume.
I would like to disable these specific messages. I realize I can disable all messages from server monitor regarding disk statuses, but then I would be turning off messages about failures and actual problems.
Is there a config I can edit which will only alert me to actual problems? I'd like to stop getting 48 emails each day; reduce the noise and increase the signal.I know this post is old but this has recently cropped up for me. I have been backing up with Time Machine for months without a single alert. It started happening after I replaced the failed battery on my RAID card. A coincidence...however the prolonged down time surely caused an SMC (and perhaps PRAM) reset which I assume triggered the change in behavior.
I've pinned it down to Time Machine backing up service settings, in particular the Open Directory archive. Time Machine backs up all the service data independently from the rest of the data on your server startup volume.
http://support.apple.com/kb/ht5139
You can see this data in Terminal.
serveradmin$ cd /Volumes/[YourBackupVolume]/Backups.backupdb/[YourServerName]/Latest/[YourBootVolume]/.ServerBackups
serveradmin$ ls -al
total 16
drwxr-xr-x@ 2 root admin 68 4 Jun 14:44 (null)
drwxr-xr-x@ 14 root admin 476 4 Jun 14:44 .
drwxrwxr-t@ 43 root admin 1462 4 Jun 14:43 ..
-rw-r--r--@ 1 root admin 37 4 Jun 14:44 .serverBackupSignature
drwxr-xr-x@ 2 root admin 68 4 Jun 14:44 addressBookServer
drwxr-xr-x@ 2 root admin 68 4 Jun 14:44 calendarServer
drwxr-xr-x@ 5 root admin 170 4 Jun 14:44 iChatServer
drwxr-xr-x@ 6 root admin 204 4 Jun 14:44 mailServer
-rw-r--r--@ 1 root admin 3826 4 Jun 14:44 master.browse.plist
drwxr-xr-x@ 4 root admin 136 4 Jun 14:43 openDirectory
drwxr-xr-x@ 61 root admin 2074 4 Jun 14:44 serverSettings
drwxr-xr-x@ 23 root admin 782 4 Jun 14:44 sharePoints
drwxr-xr-x@ 8 root admin 272 4 Jun 14:44 webServer
drwxr-xr-x@ 2 root admin 68 4 Jun 14:44 wikiServer
If you take a look inside the openDirectory folder you should see this:
serveradmin$ cd openDirectory
serveradmin$ ls -al
total 81936
drwxr-xr-x@ 4 root admin 136 4 Jun 15:32 .
drwxr-xr-x@ 14 root admin 476 4 Jun 15:33 ..
-rw-rw----@ 1 root admin 41947136 4 Jun 15:32 ServerBackup_OpenDirectoryMaster.sparseimage
-rw-r--r--@ 1 root admin 249 4 Jun 15:32 openDirectory.browse.plist
The ServerBackup_OpenDirectoryMaster.sparseimage contains an archive of your Open Directory database like the one you create from Server Admin. The only difference is that it appears to be unencrypted. This is a bit worrying since Snow Leopard, as far as I know, does not have an option to encrypt your Time Machine backup. This image seems to invisibly mount whenever a Time Machine backup is triggered. This can be verified by checking /private/var/log/system.log and filtering for backup
serveradmin$ tail -b 100 /var/log/system.log | grep backup
Jun 4 16:00:56 yourservername com.apple.backupd[25117]: Starting standard backup
Jun 4 16:00:56 yourservername com.apple.backupd[25117]: Backing up to: /Volumes/YourBackupVolume/Backups.backupdb
Jun 4 16:00:56 yourservername servermgrd[75]: servermgr_backup: TimeMachinePreBackupHook called.
Jun 4 16:09:26 yourservername servermgrd[75]: servermgr_backup: TimeMachinePreBackupHook done.
Jun 4 16:09:44 yourservername com.apple.backupd[25117]: No pre-backup thinning needed: 4.60 GB requested (including padding), 8.40 GB available
Jun 4 16:10:14 yourservername com.apple.backupd[25117]: Copied 744 files (364.4 MB) from volume YourBootDrive.
Jun 4 16:10:14 yourservername com.apple.backupd[25117]: No pre-backup thinning needed: 4.09 GB requested (including padding), 8.04 GB available
Jun 4 16:10:17 yourservername com.apple.backupd[25117]: Copied 87 files (877 KB) from volume YourBootDrive.
Jun 4 16:10:18 yourservername servermgrd[75]: servermgr_backup: TimeMachinePostBackupHook called.
Jun 4 16:10:18 yourservername servermgrd[75]: servermgr_backup: TimeMachinePostBackupHook done.
Jun 4 16:10:18 yourservername com.apple.backupd[25117]: Starting post-backup thinning
Jun 4 16:10:29 yourservername com.apple.backupd[25117]: Deleted backup /Volumes/YourBackupVolume/Backups.backupdb/yourservername/2013-06-03-155910: 8.40 GB now available
Jun 4 16:10:29 yourservername com.apple.backupd[25117]: Post-back up thinning complete: 1 expired backups removed
Jun 4 16:10:29 yourservername com.apple.backupd[25117]: Backup completed successfully.
You can see at 16:00:56 Server Manager got a call from Time Machine to start the services backup and finished at 16:09:26. Open Directory would have been backed up during that process. Take a look at /private/var/log/hwmond.log
serveradmin$ tail /private/var/log/hwmond.log
Tue Jun 4 16:08:36 BST 2013 - Number of drives change from 4 to 5.
Tue Jun 4 16:08:48 BST 2013 - Number of drives change from 5 to 4.
You'll see that both drive change warnings from Server Monitor occured just before the services backup completed. You can also use the sudo diskarbitrationd -d command along with tail /private/var/log/diskarbitrationd.log in another terminal window, trigger a Time Machine backup manually and watch this disk image mount during the backup process. Compare the mount times with the above logs to see if they all match up.
Although I have discovered the cause (which thankfully seems harmless) I have not discovered a way to stop it from generating pointless alerts. I'll post here if I figure it out. I am in the process of upgrading all of my servers to Mountain Lion so it may be a moot point. I am hopeful this information may help someone out there even though it is thoroughly out of date.
Scot -
How can i ensure that the harddisk3 designation is relatd with USB etxernal disk?
I have several erros in LOGs:
An error was detected on device \Device\Harddisk3\DR3 during a paging operation.
and
The driver detected a controller error on \Device\Harddisk3\DR7
All times are HardDisk3 and sometimes it references to DR3 and sometimes DR7
My disk structure is:
2 RAID5 arrays fomr the same disks (80GB and 2 TB)
and USB 2 TB External hard disk with several partitions
I´m 99% sure that the error is related to the external USB disk and the Dell DIag tool shows no problems with any component
DISKPART> list disk
Disk ### Status Size Free Dyn Gpt
Disk 0 Online 80 GB 0 B
Disk 1 Online 2711 GB 0 B *
Disk 2 Online 1862 GB 1024 KB
DISKPART> sele disk 0
Disk 0 is now the selected disk.
DISKPART> detail disk
DELL PERC H700 SCSI Disk Device
Disk ID: 6EFE3928
Type : RAID
Status : Online
Path : 1
Target : 0
LUN ID : 0
Location Path : PCIROOT(0)#PCI(0400)#PCI(0000)#RAID(P01T00L00)
Current Read-only State : No
Read-only : No
Boot Disk : Yes
Pagefile Disk : Yes
Hibernation File Disk : No
Crashdump Disk : Yes
Clustered Disk : No
Volume ### Ltr Label Fs Type Size Status Info
Volume 3 System Rese NTFS Partition 100 MB Healthy System
Volume 4 C DISCO NTFS Partition 79 GB Healthy Boot
DISKPART> sele disk 1
Disk 1 is now the selected disk.
DISKPART> detail disk
DELL PERC H700 SCSI Disk Device
Disk ID: {A42559A8-43EF-4570-B4CF-336A22A718BF}
Type : RAID
Status : Online
Path : 1
Target : 1
LUN ID : 0
Location Path : PCIROOT(0)#PCI(0400)#PCI(0000)#RAID(P01T01L00)
Current Read-only State : No
Read-only : No
Boot Disk : No
Pagefile Disk : No
Hibernation File Disk : No
Crashdump Disk : No
Clustered Disk : No
Volume ### Ltr Label Fs Type Size Status Info
Volume 5 DADOS NTFS Partition 2711 GB Healthy
C:\DADOS\
DISKPART> sele disk 2
Disk 2 is now the selected disk.
DISKPART> detail disk
HP External HDD USB Device
Disk ID: 000904F0
Type : USB
Status : Online
Path : 0
Target : 0
LUN ID : 0
Location Path : UNAVAILABLE
Current Read-only State : No
Read-only : No
Boot Disk : No
Pagefile Disk : No
Hibernation File Disk : No
Crashdump Disk : No
Clustered Disk : No
Volume ### Ltr Label Fs Type Size Status Info
Volume 6 SOFTWARE NTFS Partition 300 GB Healthy
C:\DADOS\DISCO-EXTRA\
Volume 7 TEMPORARIO- NTFS Partition 148 GB Healthy
C:\DADOS\NEW_TRANSF\TEMPORARIO\
Volume 8 TRANSF_LIXO NTFS Partition 149 GB Healthy
C:\DADOS\NEW_TRANSF\TRANSF_LIXO\
Volume 9 R RESTORE NTFS Partition 1264 GB HealthyHi,
For finding the exact hard disk you could refer to this article. It is an old article but the structure is not changed:
How to Distinguish a Physical Disk Device from an Event Message
http://support.microsoft.com/kb/159865
Meanwhile for the error message "error was detected on device \Device\Harddisk3\DR3 during a paging operation", according to my search result it could be related to fragments. So please try a defragment on your hard disk (if it is the USB disk then perform
a defragment on USB disk) and see the result.
If you have any feedback on our support, please send to [email protected] -
Windows is Scanning and repairing drive... (- Errors in Event Viewer)
Long post, please be patient... :)
I have a fairly new (purchased 8/2013) Lenovo ThinkPad T431s with Windows 8.1 Pro 64-bit (updated from 8.0 -> 8.1). It has a very tricky error coming basically 8 / 10 boots:
Windows is Scanning and repairing drive...
Error details from Windows Event Viewer (a new similar error appears on every boot to event viewer):
A corruption was discovered in the file system structure on volume \?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984}.
A file on the volume is no longer reachable from its parent directory. The parent file reference number is 0x2000000000002. The name of the parent directory is "". The parent index attribute is ":$I30:$INDEX_ALLOCATION". The file reference
number of the file that needs to be reconnected is 0x400000003db80. There may be additional files on the volume that also need to be reconnected to this parent directory.
What has been done 1st trying to fix that:
SSD disk has been changed (image from previous SSD copied back) ->
no solution, error remains
chkdsk /F /R -> no solution, error remains
SFC /scannow -> no solution, error remains
dism /online /cleanup-image /restorehealth -> no solution, error remains after a few boots
TRIED using Windows 8.1 "Update & Recovery -> Refresh Your PC without affecting your files" -> Inserted the Lenovo "Operating System Recovery Disk Windows 8 Pro (OEM Activation 3.0 Required)" BUT Windows did not accept
that DVD claiming "The media inserted is not valid"... ???
Ended up calling Lenovo Support and they instructed me to order the Recovery DVD from
Lenovorecovery.com -> Unfortunatelly Windows does not recognice the DVD(s)...
mountvol returns:
\\?\Volume{4d337687-0033-42f7-8a8e-b6968b533cb3}\
(This is my C:\ drive where Windows installation resides)
\\?\Volume{e010cf9d-c04d-4c82-b517-3cda1b647fe7}\
*** NO MOUNT POINTS ***
\\?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984}\
*** NO MOUNT POINTS ***
\\?\Volume{33f0062f-0aff-4fd2-8402-1c7911d86897}\
*** NO MOUNT POINTS ***
Then running fsutil dirty query on each returns:
Volume - \\?\Volume{4d337687-0033-42f7-8a8e-b6968b533cb3} is NOT Dirty
Volume - \\?\Volume{e010cf9d-c04d-4c82-b517-3cda1b647fe7} is NOT Dirty
Volume - \\?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984} is Dirty
Volume - \\?\Volume{33f0062f-0aff-4fd2-8402-1c7911d86897} is NOT Dirty
The chkdsk on the dirty volume
\\?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984}\ returned:
The type of the file system is NTFS.
Insufficient storage available to create either the shadow copy storage file or
other shadow copy data.
A snapshot error occured while scanning this drive. Run an offline scan and fix.
Diskpart output on the same volume:
DISKPART> lis par
Partition ### Type Size Offset
Partition 1 Reserved 128 MB 17 KB
Partition 2 Recovery 1000 MB 129 MB
Partition 3 System 260 MB 1129 MB
Partition 4 Primary 146 GB 1389 MB
Partition 5 Recovery 350 MB 147 GB
Partition 6 Recovery 19 GB 148 GB
Questions:
1) Are my Partitions OK, haven't "touched" anything?
2) Excluded the dirty volume from boot checking with chkntfs /x
-> still the Error appears in Event viewer log (but Scanning is skipped/not shown anymore during the boot).
What is causing the error?
3) Why do I have three (3) recovery partitions?What has happened in the past days:
A) Lenovo on-site-Support changed the motherboard -> had no impact on the error (which I expected).
B) I found
instructions how to manually create USB Flash stick with a booting Custom (OEM) Recovery Image.
C) Booted with USB and performed "Refresh your PC without affecting your files."
D) Windows was refreshed but...
-->>
Still the error remains (Windows scanning and repairing drive \?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984} on each and every boot.
1) Related Error in Event viewer (NTFS):
A corruption was discovered in the file system structure on volume \?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984}.
A file on the volume is no longer reachable from its parent directory. The parent file reference number is 0x2000000000002. The name of the parent directory is "". The parent index attribute is ":$I30:$INDEX_ALLOCATION". The file reference number of the
file that needs to be reconnected is 0x400000003db80. There may be additional files on the volume that also need to be reconnected to this parent directory.
2) Related Error in Event viewer (NTFS - Microsoft Windows NTFS):
Volume \\?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984} (\Device\HarddiskVolume5) needs to be taken offline to perform a Full Chkdsk. Please run "CHKDSK /F" locally via the command line, or run "REPAIR-VOLUME <drive:>" locally or remotely via
PowerShell.
-->>
Now Lenovo support is proposing a full re-install (to be performed by myself) of Windows as this is SW issue.
Summary:
- Refreshing my T431s with OEM Image does not help
- The error remains on \?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984} (\Device\HarddiskVolume5; Lenovo Recovery partition) OR at least Windows thinks so... -
Trying to copy iPhoto Library to external hard drive for backup. Error message: The Finder can't complete the operation because some data in "iPhoto Library" can't be read or written (Error code -36).
That code is
-36
ioErr
I/O error (bummers)
Make sure the EHD is formatted OS X Extended (journaled) and run Disk Utilty on the EHD and repair the disk. If that fails to help I'd try the following:
Using iPhoto Library Manager to Rebuild Your iPhoto Library
Download iPhoto Library Manager and launch.
Click on the Add Library button,
navigate to your Home/Pictures folder and select your iPhoto Library folder.
Now that the library is listed in the left hand pane of iPLM, click on your library and go to the Library ➙ Rebuild Library menu option
In the next window name the new library and select the external HD as the location of the newly rebild library.
Click on the Create button.
Note 1: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments. However, books, calendars, cards and slideshows will be lost.
Note 2: Your current library will be left untouched for further attempts at a fix if so desired.
OT -
I'm getting this problem when trying to update my iphone 3gs it says that the iphone software could not be contacted and I went on youtube got some advise to go into my hard drive to fix the error I have nothing in my host file please help me if you can this is all new to me.
Read this: iOS 4: Updating your device to iOS 5 or later
... oh I think it is a 3gs or a 3
This makes a difference. What does it say in Settings > General > About? -
Driver Version Not Found" Error when installing drivers for X-fi Xtreme audio
I recently bought the game Bioshock off steam and have been unable to play as it crashes as soon as I try to launch it. After doing some digging around I found out it was a sound problem. When I was looking at the drivers for my sound card (Sound Blaster X-Fi Xtreme Audio) I noticed that the driver called:?XFXA_PCDRV_LB__04_0079.exe has a fix for Bioshock. However when I install the driver I get the error "Driver version not found". I am positi've it is the correct driver for my sound card. I am on Windows 7 64bit.
Hey!
I have Vista Ultimate x64 and I ran windows update couple days ago. There was a new update for my xtreme audio pci-e. I installed it and now my driver version in creative software update is .3.2. Before i updated i ran creative's own software update. It didn't find any new drivers. I was WTF. I think that new driver fixed my volume problem. I had problem's when there was a deep bass in a song. The sound card lowered volume levels then somehow. Now that happens no more. In vista's device control it shows the driver version as 6.0.0.203. Driver date is 7 october 2008. -
I am using oracle gateway (11.1) for sqlserver on Linux platform with Oracle Server 10g.
I am getting following error when i run any select query:
ORA-28500: connection from ORACLE to a non-Oracle system returned this message:
[Oracle][ODBC SQL Server Driver][libssclient22]General network error. Check your network documentation.[Oracle][ODBC SQL Server Driver][libssclient22]ConnectionOpen (connect()).[Oracle][ODBC SQL Server Driver]Invalid connection string attribute
ORA-02063: preceding 2 lines from SQLSERVER
Another thing is, i have created a ODBC DSN named as "sqlserver" as well. This configuration works fine when "program" parameter is set to dg4odbc in Listener.ora. But with dg4msql, it gives error.
Followings are the configuration files:
initsqlserver.ora
# HS init parameters
HS_FDS_CONNECT_INFO=database_machine:1433//test_master
HS_FDS_TRACE_LEVEL=OFF
HS_FDS_RECOVERY_ACCOUNT=RECOVER
HS_FDS_RECOVERY_PWD=RECOVER
listener.ora
SID_LIST_sqlserver =
(SID_LIST =
(SID_DESC =
(SID_NAME = sqlserver)
(ORACLE_HOME = /u01/app/oracle/product/11.1.0.6.0/gateway)
(PROGRAM = dg4msql)
sqlserver =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = Server_Machine )(PORT = 1522))
(ADDRESS = (PROTOCOL = IPC)(KEY = PNPKEY))
tnsnames.ora
SQLSERVER =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = Server_Machine)(PORT = 1522))
(CONNECT_DATA =
(SID = sqlserver)
(HS = OK)
)Hi,
The error you get is because your HS_FDS_CONNECT_STRING is not correct:
Be sure you can ping the SQL SERVER name from the Oracle Server,or use TCP/IP address
Check the port, it is not necessary 1433.
You can use the instance name insted of port:
HS_FDS_CONNECT_STRING=server_ip_address/instance_name/database_name
Be careful, in the LISTENER.ORA, you must specify the Gateway machine and not the SQL SERVER machine:
sqlserver =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = Gateway_Machine )(PORT = 1522)) <====you must specify Oracle Gateway machine
(ADDRESS = (PROTOCOL = IPC)(KEY = PNPKEY))
Idem for TNSNAMES.ORA:
SQLSERVER =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = Gateway_Machine)(PORT = 1522))
(CONNECT_DATA =
(SID = sqlserver)
(HS = OK)
Regards
Mireille -
[ODBC Driver Manager] Function sequence error
Hi all,
i´m trying to built an webservice and if i try to run my code i get following
error: [ODBC Driver Manager] Function sequence error .CAn someone tell me what
this means?
Here comes my code:
static String Daten(int Nummer)
java.sql.Connection conn = null;
java.sql.Statement stmt = null;
try
Context ctx = null;
Hashtable ht = new Hashtable();
ht.put(Context.INITIAL_CONTEXT_FACTORY,
"weblogic.jndi.WLInitialContextFactory");
ht.put(Context.PROVIDER_URL,
"t3://localhost:7001");
// Get a context for the JNDI look up
ctx = new InitialContext(ht);
javax.sql.DataSource ds
= (javax.sql.DataSource) ctx.lookup ("webservice-data-source");
conn = ds.getConnection();
System.out.println("Making connection...\n");
// execute some SQL statements to demonstrate the connection.
stmt = conn.createStatement();
System.out.println("Vor ResultSet");
ResultSet result = stmt.getResultSet(); //Bringt Fehler
final Vector erstespalte = new Vector();
final Vector zweitespalte = new Vector();
final Vector drittespalte = new Vector();
final Vector Zeilen;
final Vector end = new Vector();
try {//2.Block
stmt.executeQuery("Select * from Person where Kundennummer=5");
while(result.next())
erstespalte.add(result.getObject(1));
zweitespalte.add(result.getObject(2));
drittespalte.add(result.getObject(3));
Zeilen = new Vector();
for(Enumeration a = erstespalte.elements() ; a.hasMoreElements()
for(Enumeration b = zweitespalte.elements() ;b .hasMoreElements()
for(Enumeration c = drittespalte.elements() ; c.hasMoreElements()
Zeilen.add(a.nextElement());
Zeilen.add(b.nextElement());
Zeilen.add(c.nextElement());
end.add(Zeilen);
}System.out.println(end);
result.close();
}//2.try-Block
catch (SQLException e) {
System.out.println(e);
}//1.try-Block schliessen
catch (Exception e) {
System.out.println("Exception was thrown: " + e.getMessage());
finally {
try {
if (stmt != null)
stmt.close();
if (conn != null)
conn.close();
catch (SQLException sqle) {
System.out.println("SQLException during close(): " + sqle.getMessage());
}//finally-Block schliessen
return ("HAllo");
}//Methode abschliessen
Thank you very much for helping !!!Please post this in the JDBC newsgroup: weblogic.developer.interest.jdbc
Also, please include your full error message.
-- Rob
Hakan wrote:
Hi all,
i´m trying to built an webservice and if i try to run my code i get following
error: [ODBC Driver Manager] Function sequence error .CAn someone tell me what
this means?
Here comes my code:
static String Daten(int Nummer)
java.sql.Connection conn = null;
java.sql.Statement stmt = null;
try
Context ctx = null;
Hashtable ht = new Hashtable();
ht.put(Context.INITIAL_CONTEXT_FACTORY,
"weblogic.jndi.WLInitialContextFactory");
ht.put(Context.PROVIDER_URL,
"t3://localhost:7001");
// Get a context for the JNDI look up
ctx = new InitialContext(ht);
javax.sql.DataSource ds
= (javax.sql.DataSource) ctx.lookup ("webservice-data-source");
conn = ds.getConnection();
System.out.println("Making connection...\n");
// execute some SQL statements to demonstrate the connection.
stmt = conn.createStatement();
System.out.println("Vor ResultSet");
ResultSet result = stmt.getResultSet(); //Bringt Fehler
final Vector erstespalte = new Vector();
final Vector zweitespalte = new Vector();
final Vector drittespalte = new Vector();
final Vector Zeilen;
final Vector end = new Vector();
try {//2.Block
stmt.executeQuery("Select * from Person where Kundennummer=5");
while(result.next())
erstespalte.add(result.getObject(1));
zweitespalte.add(result.getObject(2));
drittespalte.add(result.getObject(3));
Zeilen = new Vector();
for(Enumeration a = erstespalte.elements() ; a.hasMoreElements()
for(Enumeration b = zweitespalte.elements() ;b .hasMoreElements()
for(Enumeration c = drittespalte.elements() ; c.hasMoreElements()
Zeilen.add(a.nextElement());
Zeilen.add(b.nextElement());
Zeilen.add(c.nextElement());
end.add(Zeilen);
}System.out.println(end);
result.close();
}//2.try-Block
catch (SQLException e) {
System.out.println(e);
}//1.try-Block schliessen
catch (Exception e) {
System.out.println("Exception was thrown: " + e.getMessage());
finally {
try {
if (stmt != null)
stmt.close();
if (conn != null)
conn.close();
catch (SQLException sqle) {
System.out.println("SQLException during close(): " + sqle.getMessage());
}//finally-Block schliessen
return ("HAllo");
}//Methode abschliessen
Thank you very much for helping !!! -
Spectrum digital DSK5416 driver setup gives an error when test wizard is run.
Please help us with the following problem we are facing:
1. Spectrum digital DSK5416 driver setup gives an
error when test wizard is run. A snap shot of the same has been
attached.
2. The A/D module doesn’t pickup microphone signal or
an audio sample for loopback but the implementation of the same works
fine in CCS environment. (We are using Mic In and Speaker Out lines)
3. When a real-time application has run successfully
and if you close the VAB environment the application starts running
automatically until you reset the board.
4. We don’t find the flash program button enabled, so
that any real-time program can be burned into flash and demonstrate the
embedded feature.
Note:
We are using Windows Xp professional edition.
Program is developed using DSK5416Hello, I have included some information that will help address your questions: (1) I couldn't see the attached image file (contained errors). The RIDE/VAB DSK5416 Driver makes use of a JTAG communication when reading/writing memory on the DSK5416 hardware. You will need to make sure that the JTAG transfer option has been selected in the Driver Setup dialog box. The memory test process may seem to take a long time due to the amount of memory being accessed. (2) The VAB RTDSKAD block component provides a one-channel A/D input that makes use of the line-in channel on the DSK5416 hardware. (3) VAB does not remove the downloaded DSP executable program from DSK5416 memory, and it does remain resident. That being said, I wouldn't expect that the program would begin execution when VAB is closed. I would recommend that you verify that the DSP program stopped properly upon selecting the VAB Stop command. Then, close VAB as normal. (4) The RIDE/VAB driver for the DSK5416 does not support programming of flash memory on the DSK5416 hardware. Regards, Steve
-
[Microsoft][ODBC driver for Oracle]Syntax error or access violation
Hi,
When I am trying to connect to Oracle 8.1.6 database using Microsoft ODBC driver for Oracle. The connection is established.
But while creating CallableStatement, I am getting error "[Microsoft][ODBC driver for Oracle]Syntax error or access violation".
What I need to do to resolve this problem.
RajHi Satish
It could be an issue with the driver.
You can try with the OLEDB n Oracle native connection to test if the issue persists.
Also you can refer to the [Troubleshooting Database Connectivity for Crystal Reports|http://www.sdn.sap.com/irj/boc/index?rid=/library/uuid/d05b3bb7-0f28-2c10-4ea3-84dbdc4e414e&overridelayout=true]
Hope this helps!!
Regards
Sourashree -
Dvd caddy and drive replaced...error results
i have a powerbook g3 pismo...dvd caddy broke...i ordered a whole new module...in a new caddy...when i try to put it in computer it says "there was an initialization error
a valid dvd drive could not be found (-70012)"
i have os x 10.9.3....400 mhz, 256 ram
have tried to get help from discussion groups, but no one so far has been able to help...
would really!! appreciate any help....
ariellaariella,
This article discusses using an external DVD drive to play DVD movies and generating the -70012 error:
http://docs.info.apple.com/article.html?artnum=42727
Are you saying inserting the DVD drive module generates this error or the error occurs when you insert a DVD optical disk?
Since you are apparently using a media bay optical drive, a few questions:
- Does your new drive work properly with CDs and data DVDs like a MacOS X System Install disk?
- Open your System Profiler > Hardware > ATA and please report on the model number of the optical drive. If OEM, it should report LG or Matshita and also say DVD-ROM.
Let us know the results of the above...
Maybe you are looking for
-
Does anyone know what is the major differences between the windows 8.1 option listed
Hello, I have two questions. I downloaded Windows 8.1 Enterprise, Enterprise N, Pro VL, and Pro N VL ISO from msdn.microsoft.com. Then upgraded my computer with that ISO. That was a mistake. Now I want to download another version, but not sure what t
-
HP 1200 not printing pdfs/uses default fonts in Word docs
Happy Birthday USA! Last week I loaded 10.4.10 to Mac mini and eversince I have not been able to print pdfs from Adobe Reader or print desired fonts from Word. (I have overcome default to US letter problem in Word) I have loaded latest drivers from H
-
Hi everybody, I have a problem and I will be very happy if you could help me, when I startup database the problem is appeared as shown below: SQL> STARTUP ORACLE instance started. Total System Global Area 599785472 bytes Fixed Size 1250356 bytes Vari
-
After several years my Quicken Essentials will not open. I repeatedly get a cocoa error 266 message. Downloaded another version of Essentials with no results.
-
Setup F110 as an automatic nightly batch job
Hello Gurus, Can anyone please tell me how do I set up the F110 payment batch job as an automatic nightly batch job. I tried doing it in sm36 but I dont think so it would work because i was not able to create the parameters